Since the introduction of clk-si5351 the way we should deal with DT provided
clocks has changed from indexed to named clock phandles. Amend the binding
documentation to reflect named clock phandles by clock-names property.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Add small documentation for GTM601 UMTS modem audio interface.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Open firmware is already using the serial-number property for passing the
device's serial number from the bootloader to the kernel. In addition, lshw
already has support for scanning this property.
The serial number is a string that somewhat represents the device's serial
number. It might come from some form of storage (e.g. an eeprom) and be
programmed at factory-time by the manufacturer or come from identification
bits available in e.g. the SoC (note that the soc_id property in the SoC bus
should hold a full account of those bits).
The serial number is taken as-is from the bootloader, so it is up to the
bootloader to define where the serial number comes from and what length it
should be. Some use cases for the serial number require it to have a maximum
length (e.g. for USB serial number) and some other cases imply more restrictions
on what the serial number should look like (e.g. in Android, the ro.serialno
property is usually a 16-bytes (plus one null byte) representation of a 64 bit
number).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The H3 SoC has the same dma engine as the A31 (sun6i), with a
reduced amount of endpoints and physical channels. Add the proper
config data and compatible string to support it.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use 'clock-controller' and 'power-controller' as node names in the
examples rather than the specific names of the units.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
There is a subtle typo phys-names should be phy-names. Using the
current example means you don't have working usb (as you fail to
obtain the phys). Also update the example to use the generic phy
type constants which are now used for miphy28.
Additionally also remove the unnecessary new line in the example.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
uart -> serial
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
creeping up during idle, and two l3-noc device fixes:
- Fix power consumption creeping up with I2C4 staying on
- Fix n900 microphone bias voltages
- Fix dra7 l3-noc for host clock
- Fix omap5 l3-noc id address decoding
The rest are all just minor dts fixes:
- Fix changed EXTCON_USB_GPIO_USB in defconfig
- Fix missing isp and iva #iommu-cells property
- Various beagle x15 dts fixes for pre-production changes
- Fix am437x-sk display dts entries
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tOGf
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.1/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v4.1-rc1" from Tony Lindgren:
Fixes for omaps, mostly a fix for power power consumption
creeping up during idle, and two l3-noc device fixes:
- Fix power consumption creeping up with I2C4 staying on
- Fix n900 microphone bias voltages
- Fix dra7 l3-noc for host clock
- Fix omap5 l3-noc id address decoding
The rest are all just minor dts fixes:
- Fix changed EXTCON_USB_GPIO_USB in defconfig
- Fix missing isp and iva #iommu-cells property
- Various beagle x15 dts fixes for pre-production changes
- Fix am437x-sk display dts entries
* tag 'omap-for-v4.1/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: omap_l3_noc: Fix master id address decoding for OMAP5
bus: omap_l3_noc: Fix offset for DRA7 CLK1_HOST_CLK1_2 instance
ARM: dts: dra7: Fix efuse register size for ABB
ARM: dts: am57xx-beagle-x15: Switch GPIO fan number
ARM: dts: am57xx-beagle-x15: Switch UART mux pins
ARM: dts: am437x-sk: reduce col-scan-delay-us
ARM: dts: am437x-sk: fix for new newhaven display module revision
ARM: dts: am57xx-beagle-x15: Fix RTC aliases
ARM: dts: am57xx-beagle-x15: Fix IRQ type for mcp7941x
ARM: dts: omap3: Add #iommu-cells to isp and iva iommu
ARM: omap2plus_defconfig: Enable EXTCON_USB_GPIO
ARM: dts: OMAP3-N900: Add microphone bias voltages
ARM: OMAP2+: Fix omap off idle power consumption creeping up
The LSM303DLH accelerometer/magnetometer has a different
device identification method than using register 0x0f, instead
three registers contain a magic value. We rely on WhoAmI
to be zero for this variant.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The mtk 8250 needs two clocks, one for providing the baudrate and
one that needs to be enabled for register accesses. The latter has
not been supported, this patch adds support for it. It is optional
for now since not all SoCs provide a bus clock.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 52bec4ed4e("serial: sirf: add a new uart type
support").
we misunderstood the clock dependency in atlas7. Actually involved
several clocks are in a tree structure. we still only need to take
the leaf clock node for BT uarts.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Barry.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since SCLK, MISO and MOSI are the only mandatory signals at Zynq's SPI
interfaces, SS0, SS1 and SS2 have to be configured separately as they may
be used as simple GPIO lines.
This, of course, has to be considered in the devicetree, so pin controller
configuration for e.g. an SPI0 using SS0 and SS1 only might look like the
following snippet (derived from the example of chapter "17.5.3
MIO/EMIO" Routing of Zynq-7000 TRM UG585). So MIO20 can now be used
as GPIO instead of being occupied by SPI0 SS2 function. Note the separate
pinmux function for the slave select signals:
pinctrl_spi0_default: spi0-default {
mux_spi {
function = "spi0";
groups = "spi0_0_grp";
};
mux_ss {
function = "spi0_ss";
groups = "spi0_0_ss0_grp", "spi0_0_ss1_grp";
}
conf-output {
pins = "MIO16", "MIO21";
slew-rate = <0>;
bias-disable;
low-power-disable;
io-standard = <1>;
};
conf-input {
pins = "MIO17";
slew-rate = <0>;
bias-high-impedance;
low-power-disable;
io-standard = <1>;
};
conf-select {
pins = "MIO18", "MIO19";
slew-rate = <0>;
bias-pull-up;
low-power-disable;
io-standard = <1>;
};
};
pinctrl_gpio0_default {
mux {
function = "gpio0";
groups = "gpio0_20_grp"
};
conf {
pins = "MIO20";
slew-rate = <0>;
bias-pull-up;
low-power-disable;
io-standard = <1>;
};
};
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the binding documentation for the apmixedsys, perisys and
infracfg controllers found on Mediatek SoCs.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Document the bindings for abracon,abx80x and related compatibles.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Philippe De Muyter <phdm@macqel.be>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MC driver needs some timing-specific information to program the EMEM
during a rate change of the EMC clock.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Introduce an optional property called, sustainable-power, which
represents the power (in mW) which the thermal zone can safely
dissipate.
If provided the property is parsed and associated with the thermal
zone via the thermal zone parameters.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add support for the temperature alarm peripheral found inside
Qualcomm plug-and-play (QPNP) PMIC chips. The temperature alarm
peripheral outputs a pulse on an interrupt line whenever the
thermal over temperature stage value changes.
Register a thermal sensor. The temperature reported by this thermal
sensor device should reflect the actual PMIC die temperature if an
ADC is present on the given PMIC. If no ADC is present, then the
reported temperature should be estimated from the over temperature
stage value.
Cc: David Collins <collinsd@codeaurora.org>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This adds device tree binding documentation for the Broadcom BCM6328 LED controller.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch adds device tree binding documentation for
1.5A Step-Up Current Regulator for Flash LEDs.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: devicetree@vger.kernel.org
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Document the binding for the TLC591xx LED driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Imre Kaloz <kaloz@openwrt.org>
Cc: Matthew.Fatheree@belkin.com
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The L3 Error handling on OMAP5 for the most part is very similar
to that of OMAP4, and had leveraged common data structures and
register layout definitions so far. Upon closer inspection, there
are a few minor differences causing an incorrect decoding and
reporting of the master NIU upon an error:
1. The L3_TARG_STDERRLOG_MSTADDR.STDERRLOG_MSTADDR occupies
11 bits on OMAP5 as against 8 bits on OMAP4, with the master
NIU connID encoded in the 6 MSBs of the STDERRLOG_MSTADDR
field.
2. The CLK3 FlagMux component has 1 input source on OMAP4 and 3
input sources on OMAP5. The common DEBUGSS source is at a
different input on each SoC.
Fix the above issues by using a OMAP5-specific compatible property
and using SoC-specific data where there are differences.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
rcar_sound -> sound
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document the bindings for the soon-to-be-added tas571x driver.
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
For consistency with other device tree content, use lower-case
hexadecimal digits in register region specifications.
Signed-off-by: Thierry Reding <treding@nvidia.com>
HwSpinlock IP is present only on OMAP4 and other newer SoCs,
which are all device-tree boot only. This patch adds the
DT bindings information for OMAP hwspinlock module.
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
This patch adds the generic common bindings used to represent
a hwlock device and use/request locks in a device-tree build.
Each hwspinlock provider should have the '#hwlock-cells' property,
which represents the number of cells to be used for representing
a specific hwspinlock. Client users shall use the property
'hwlocks' for requesting specific lock(s).
Note that the document is named hwlock.txt deliberately to keep
it a bit more generic.
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
On current ST platforms the LPC controls a number of functions including
Watchdog and Real Time Clock. This patch provides the bindings used to
configure LPC in RTC mode.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On current ST platforms the LPC controls a number of functions including
Watchdog and Real Time Clock. This patch provides the bindings used to
configure LPC in Watchdog mode.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
VBUS is not routed to USB PHY on recent Qualcomm platforms. USB controller
must see VBUS in order to pull-up DP when setting RS bit. Henc configure
USB PHY and LINK registers sense VBUS and enable manual pullup on D+ line.
Cc: Vamsi Krishna <vskrishn@codeaurora.org>
Cc: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On recent Qualcomm platforms VBUS and ID lines are not routed to
USB PHY LINK controller. Use extcon framework to receive connect
and disconnect ID and VBUS notification.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since the DT should describe the hardware (not the driver limitation),
This patch revises the binding document about the dma-names to change
simple numbering as "ch%d" instead of "tx<n>" and "rx<n>".
Also this patch fixes the actual code of renesas_usbhs driver to handle
the new dma-names.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix a typo in the TX DMA interrupt name for AUART4.
This patch makes AUART4 operational again.
Signed-off-by: Marek Vasut <marex@denx.de>
Fixes: f30fb03d4d ("ARM: dts: add generic DMA device tree binding for mxs-dma")
Cc: stable@vger.kernel.org
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The adau1701 has two power domains, DVDD and AVDD.
Enable them both as long as the codec is in use.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds vendor-prefix for Wexler.
WEXLER trademark owned by AVIRSA Electronics, a member of the
diversified holding AVIRSA.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a cubietech vendor prefix, as it is missing. The cubietruck, cubieboard2,
and cubieboard all already reference this prefix.
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A23 is a dual Cortex-A7. Add the logic to use the IPs used to
control the CPU configuration and the CPU power so that we can
bring up secondary CPUs at boot.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
MSIOF Base Address H'E6xx can be accessed by CPU and DMAC.
MSIOF Base Address H'E7xx for DMAC was removed from H/W manual.
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAlU70nMACgkQ31LbvUHyf1cYgwCfSmPhyLFmr0pGM/BxsVY7K1v6
PaEAn2+7xfZV38E6hwrGMrT42ZvKyL6r
=LHQU
-----END PGP SIGNATURE-----
Merge tag 'cris-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris
Pull arch/cris updates from Jesper Nilsson:
"Some much needed love for the CRIS-port.
There's a bunch of changes this time, giving the CRISv32 port a bit of
modern makeover with device-tree, irq domain and gpiolib support, and
more switchover to generic frameworks.
Some small fixes and removal of the theoretical SMP support brings up
the rear"
* tag 'cris-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
cris: fix integer overflow in ELF_ET_DYN_BASE
CRISv32: use GENERIC_SCHED_CLOCK
CRISv32: use MMIO clocksource
CRISv32: use generic clockevents
CRIS: use generic headers via Kbuild
CRIS: use generic cmpxchg.h
CRIS: use generic atomic.h
CRIS: use generic atomic bitops
CRISv10: remove redundant macros from system.h
CRIS: remove SMP code
CRISv32: don't enable irqs in INIT_THREAD
CRISv32: handle multiple signals
CRISv32: prevent bogus restarts on sigreturn
CRISv32: don't attempt syscall restart on irq exit
Add binding documentation for CRIS
CRIS: add Axis 88 board device tree
CRISv32: add device tree support
CRISv32: add irq domains support
CRIS: enable GPIOLIB
Not much has been happening in PWM land lately, so this contains mostly
minor fixes that didn't seem urgent enough for a late pull-request last
cycle.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=X+q2
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm changes from Thierry Reding:
"Not much has been happening in PWM land lately, so this contains
mostly minor fixes that didn't seem urgent enough for a late
pull-request last cycle"
* tag 'pwm/for-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: Remove __init initializer for pwm_add_table()
pwm: samsung: Fix output race on disabling
pwm: mxs: Fix period divider computation
pwm: atmel-hlcdc: Add errata handling for sama5d4
pwm: pca9685: Constify struct regmap_config
pwm: imx-pwm: add explicit compatible strings and required clock properties
