This patch adds another entry (HP hs2434 Mobile Broadband) to the list
of exceptional devices that require a zero length packet in order to
function properly. This list was added in commit 844e88f0. The hs2434
is manufactured by Sierra Wireless, who also produces the MC7710,
which the ZLP exception list was created for in the first place. So
hopefully it is just this one producer's devices that will need this
workaround.
Tested on a DM1-4310NR HP notebook, which does not function without this
change.
Signed-off-by: Rob Gardner <robmatic@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a cpu_relaxt to sk_busy_loop.
Julie Cummings reported performance issues when hyperthreading is on.
Arjan van de Ven observed that we should have a cpu_relax() in the
busy poll loop.
Reported-by: Julie Cummings <julie.a.cummings@intel.com>
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixed the pbl(programmable burst length) setting
using DT. Even though the default pbl is 8, If there is no
pbl property in device tree file, pbl is set 0 and it causes
bandwidth degradation.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netlink dump operations take module as parameter to hold
reference for entire netlink dump duration.
Currently it holds ref only on genl module which is not correct
when we use ops registered to genl from another module.
Following patch adds module pointer to genl_ops so that netlink
can hold ref count on it.
CC: Jesse Gross <jesse@nicira.com>
CC: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of genl-family with parallel ops off, dumpif() callback
is expected to run under genl_lock, But commit def3117493
(genl: Allow concurrent genl callbacks.) changed this behaviour
where only first dumpit() op was called under genl-lock.
For subsequent dump, only nlk->cb_lock was taken.
Following patch fixes it by defining locked dumpit() and done()
callback which takes care of genl-locking.
CC: Jesse Gross <jesse@nicira.com>
CC: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some architectures, such as ARM-32 do not return the same base address
when you call kmap_atomic() twice on the same page.
This causes problems for the memmove() call in the XDR helper routine
"_shift_data_right_pages()", since it defeats the detection of
overlapping memory ranges, and has been seen to corrupt memory.
The fix is to distinguish between the case where we're doing an
inter-page copy or not. In the former case of we know that the memory
ranges cannot possibly overlap, so we can additionally micro-optimise
by replacing memmove() with memcpy().
Reported-by: Mark Young <MYoung@nvidia.com>
Reported-by: Matt Craighead <mcraighead@nvidia.com>
Cc: Bruce Fields <bfields@fieldses.org>
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Tested-by: Matt Craighead <mcraighead@nvidia.com>
This reverts commit bb2314b479.
It wasn't necessarily wrong per se, but we're still busily discussing
the exact details of this all, so I'm going to revert it for now.
It's true that you can already do flink() through /proc and that flink()
isn't new. But as Brad Spengler points out, some secure environments do
not mount proc, and flink adds a new interface that can avoid path
lookup of the source for those kinds of environments.
We may re-do this (and even mark it for stable backporting back in 3.11
and possibly earlier) once the whole discussion about the interface is done.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The net_device might be not set on the skb when we try refcounting.
This leads to a null pointer dereference in xdst_queue_output().
It turned out that the refcount to the net_device is not needed
after all. The dst_entry has a refcount to the net_device before
we queue the skb, so it can't go away. Therefore we can remove the
refcount on queueing to fix the null pointer dereference.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The recent commit to delay the release of kobject triggered NULL
dereferences of opti9xx drivers. The cause is that all
snd-opti92x-ad1848, snd-opti92x-cs4231 and snd-opti93x drivers
register the PnP card driver with the very same name, and also
snd-opti92x-ad1848 and -cs4231 drivers register the ISA driver with
the same name, too. When these drivers are built in, quick
"register-release-and-re-register" actions occur, and this results in
Oops because of the same name is assigned to the kobject.
The fix is simply to assign individual names. As a bonus, by using
KBUILD_MODNAME, the patch reduces more lines than it adds.
The fix is based on the suggestion by Russell King.
Reported-and-tested-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the PF gathers statistics for the VF, when the VF is about to unload
we must synchronize the release of its statistics buffer with the PF, so that
no DMA operation will be made to that address after the buffer release.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to incorrect VF/PF conditions, when unloading a VF it will not release
part of the memory it has previously allocated.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check on return code of bnx2x_vfop_config_vlan0() would lead to error
handling flow as the return value indicating an existing pending ramrod would
be erroneously considered as an error.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If driver will fail to allocate all queues, it will shrink the number of
queues and move the storage queue to its correct place (i.e., the last
queue among the newly supported number).
When changing the pointers of the new location of the FCoE queue, we need
to pay special attention to the aggregations pointer - that memory is allocated
during probe and released upon driver removal. Current implementation has 2
pointers pointing to the same chunk of allocated memory, meaning upon removal
there will be two kfree() of the same chunk while the other won't be released.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Solve issue where no stats were being collected for VF devices due to missing
configuration in the stats' atomic synchronization mechanism.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch permits the generation of the Kirkwood audio driver which
may be used in the Dove boards.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
John W. Linville says:
====================
This is one more set of fixes intended for the 3.11 stream...
For the mac80211 bits, Johannes says:
"I have three more patches for the 3.11 stream: Felix's fix for the
fairly visible brcmsmac crash, a fix from Simon for an IBSS join bug I
found and a fix for a channel context bug in IBSS I'd introduced."
Along with those...
Sujith Manoharan makes a minor change to not use a PLL hang workaroun
for AR9550. This one-liner fixes a couple of bugs reported in the Red Hat
bugzilla.
Helmut Schaa addresses an ath9k_htc bug that mangles frame headers
during Tx. This fix is small, tested by the bug reported and isolated
to ath9k_htc.
Stanislaw Gruszka reverts a recent iwl4965 change that broke rfkill
notification to user space.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 82dc3c63 ("net: introduce NAPI_POLL_WEIGHT")
netif_napi_add() produces an error message if a NAPI poll weight
greater than 64 is requested.
GELIC_NET_NAPI_WEIGHT is defined to GELIC_NET_RX_DESCRIPTORS,
which is 128.
Use the standard NAPI weight.
v2: proper reference to the related commit
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 82dc3c63 ("net: introduce NAPI_POLL_WEIGHT")
netif_napi_add() produces an error message if a NAPI poll weight
greater than 64 is requested.
Use the standard NAPI weight.
v2: proper reference to the related commit
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 82dc3c63 ("net: introduce NAPI_POLL_WEIGHT")
netif_napi_add() produces an error message if a NAPI poll weight
greater than 64 is requested.
jme requests a quarter of the rx ring size as the NAPI weight.
jme's rx ring size is 1 << 9 = 512.
Use the standard NAPI weight.
v2: proper reference to the related commit
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nsproxy.pid_ns is *not* the task's pid namespace. The name should clarify
that.
This makes it more obvious that setns on a pid namespace is weird --
it won't change the pid namespace shown in procfs.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a security bug.
The follow-up will fix nsproxy to discourage this type of issue from
happening again.
Cc: stable@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two changes here:
- Fix a bug in the rbtree code which could cause it to create two
different cache entries for the same register by adding a single
register at a time to the cache. This isn't awesome for performance
but it's non-invasive which we need for this late in the release
cycle and the I/O costs we're trying to avoid are high.
- Add another header used in the !CONFIG_REGMAP stubs where we had been
relying on implicit inclusion.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=8r8F
-----END PGP SIGNATURE-----
Merge tag 'regmap-v3.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"Two changes here:
- Fix a bug in the rbtree code which could cause it to create two
different cache entries for the same register by adding a single
register at a time to the cache. This isn't awesome for
performance but it's non-invasive which we need for this late in
the release cycle and the I/O costs we're trying to avoid are high.
- Add another header used in the !CONFIG_REGMAP stubs where we had
been relying on implicit inclusion"
* tag 'regmap-v3.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: rbtree: Fix overlapping rbnodes.
regmap: Add another missing header for !CONFIG_REGMAP stubs
Pull powerpc fixes from Ben Herrenschmidt:
"Here are 3 bug fixes that should probably go into 3.11 since I'm also
tagging them for stable.
Once fixes our old /proc/powerpc/lparcfg file which provides partition
informations when running under our hypervisor and also acts as a
user-triggerable Oops when hot :-(
The other two respectively are a one liner to fix a HVSI protocol
handshake problem causing the console to fail to show up on a bunch of
machines until we reach userspace, which I deem annoying enough to
warrant going to stable, and a nasty gcc miscompile causing us to pass
virtual instead of physical addresses to the firmware under some
circumstances"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/hvsi: Increase handshake timeout from 200ms to 400ms.
powerpc: Work around gcc miscompilation of __pa() on 64-bit
powerpc: Don't Oops when accessing /proc/powerpc/lparcfg without hypervisor
Dave reported corrupted swap entries
| [ 4588.541886] swap_free: Unused swap offset entry 00002d15
| [ 4588.541952] BUG: Bad page map in process trinity-kid12 pte:005a2a80 pmd:22c01f067
and Hugh pointed that in move_ptes _PAGE_SOFT_DIRTY bit set regardless
the type of entry pte consists of. The trick here is that when we carry
soft dirty status in swap entries we are to use _PAGE_SWP_SOFT_DIRTY
instead, because this is the only place in pte which can be used for own
needs without intersecting with bits owned by swap entry type/offset.
Reported-and-tested-by: Dave Jones <davej@redhat.com>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Pavel Emelyanov <xemul@parallels.com>
Analyzed-by: Hugh Dickins <hughd@google.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
snd_soc_dapm_new_widgets() works on the ASoC card as a whole not on a specific
DAPM context. The DAPM context that is passed as the parameter is only used to
look up the pointer to the card. This patch updates the signature of
snd_soc_dapm_new_widgets() to take the card directly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Call snd_soc_dapm_new_widgets() before the auto non-connected pins have been
marked as not connected will power the system under the assumption that those
pins are connected. Once the pins have been marked as disconnected the system
there will be an additional power run. This can cause unnecessary power
transitions. Calling snd_soc_dapm_new_widgets() only after the pins have been
marked as non-connected avoids this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Each time snd_soc_dapm_new_widgets() is called it will instantiate all the
widgets and routes that have been added so far and then power them. Doing this
multiple times before the card is fully initialized and all widgets have been
added can cause unnecessary and even invalid power state transitions which can
result in extra register writes and and also might cause clicks and pops.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
snd_soc_jack_add_pins() does not create any new DAPM widgets, so there is no
need to call snd_soc_dapm_new_widgets().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The core will call snd_soc_dapm_new_widgets() once all components of the card
have been initialized, so there is no need to do this manually in the driver.
Calling it earlier also might result in a partially instantiated system being
powered up which cause undesired side effects.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Let the core take care of instantiating the controls and DAPM widgets and
routes, this makes the code a bit shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The current calls to dapm_mark_dirty() in snd_soc_dapm_add_path() are on a path
that is only reached if the sink widget is either a mixer or a mux. Move the
calls further up so they are called for all widget types.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Let the core take care of instantiating the DAPM widgets and routes, this makes
the code a bit shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
CONFIG_SND_HDA_I915 doesn't have to be user-selectable as this is almost
mandatory when i915 driver is available. Let's enable it always when
CONFIG_DRM_I915 is set, so that user won't be bothered by useless
questions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds two fields to unsolicited response, according to spec HDA040-A:
- Device Entry (bit 20:15)
- Inactive (bit 2)
and show the info in debug message.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch is only to allow codec proc file to expose devices list/select info
for Haswell codec pins.
Since Haswell Gfx driver cannot support DP1.2 MST now, so all pins' device list
is empty, meaning no pin is multi-streaming capaple.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If a display codec supports multi-stream transport on the pins, the pin's
device list length and device entries will be exposed to codec proc file.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds flags and routines to get device list & selection info on
a pin.
To support Display Port 1.2 multi-stream transport (MST) over single DP port,
a pin can support multiple devices. Please refer to HD-A spec Document Change
Notificaton HDA040-A.
A display audio codec can set flag "dp_mst" in its patch, indicating its pins
can support MST. But at runtime, a pin may not be multi-streaming capable and
report the device list is empty, depending on Gfx driver configuration.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This solves a problem observed in kexec'ed kernel where 200ms timeout is
too short and bootconsole fails to initialize. Console did eventually
become workable but much later into the boot process.
Observed timeout was around 260ms, but I decided to make it a little bigger
for more reliability.
This has been tested on Power7 machine with Petitboot as a primary
bootloader and PowerNV firmware.
CC: <stable@vger.kernel.org>
Signed-off-by: Eugene Surovegin <surovegin@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On 64-bit, __pa(&static_var) gets miscompiled by recent versions of
gcc as something like:
addis 3,2,.LANCHOR1+4611686018427387904@toc@ha
addi 3,3,.LANCHOR1+4611686018427387904@toc@l
This ends up effectively ignoring the offset, since its bottom 32 bits
are zero, and means that the result of __pa() still has 0xC in the top
nibble. This happens with gcc 4.8.1, at least.
To work around this, for 64-bit we make __pa() use an AND operator,
and for symmetry, we make __va() use an OR operator. Using an AND
operator rather than a subtraction ends up with slightly shorter code
since it can be done with a single clrldi instruction, whereas it
takes three instructions to form the constant (-PAGE_OFFSET) and add
it on. (Note that MEMORY_START is always 0 on 64-bit.)
CC: <stable@vger.kernel.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
/proc/powerpc/lparcfg is an ancient facility (though still actively used)
which allows access to some informations relative to the partition when
running underneath a PAPR compliant hypervisor.
It makes no sense on non-pseries machines. However, currently, not only
can it be created on these if the kernel has pseries support, but accessing
it on such a machine will crash due to trying to do hypervisor calls.
In fact, it should also not do HV calls on older pseries that didn't have
an hypervisor either.
Finally, it has the plumbing to be a module but is a "bool" Kconfig option.
This fixes the whole lot by turning it into a machine_device_initcall
that is only created on pseries, and adding the necessary hypervisor
check before calling the H_GET_EM_PARMS hypercall
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Here is a single bugfix that resolves the "can not build the OHCI driver
with CONFIG_PM disabled" problem that lots of people have been reporting
with 3.11-rc7. Sorry about that one, it missed my build tests, and it
seems, a number of others as well.
Thank goodness for Guenter :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIcDYsACgkQMUfUDdst+ykhqwCaAykv4ypLeDQa9cuKoxZcDeRb
wEEAoLWUzWk/ic2XrXbNZ0/pJ69bMmzs
=2yMG
-----END PGP SIGNATURE-----
Merge tag 'usb-3.11-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB bugfix from Greg KH:
"Here is a single bugfix that resolves the "can not build the OHCI
driver with CONFIG_PM disabled" problem that lots of people have been
reporting with 3.11-rc7. Sorry about that one, it missed my build
tests, and it seems, a number of others as well.
Thank goodness for Guenter :)"
* tag 'usb-3.11-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: OHCI: fix build error related to ohci_suspend/resume
client reporting a readdir loop.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)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=+aYs
-----END PGP SIGNATURE-----
Merge tag 'jfs-3.11-rc8' of git://github.com/kleikamp/linux-shaggy
Pull jfs fix from Dave Kleikamp:
"One JFS patch to fix an incompatibility with NFSv4 resulting in the
nfs client reporting a readdir loop"
* tag 'jfs-3.11-rc8' of git://github.com/kleikamp/linux-shaggy:
jfs: fix readdir cookie incompatibility with NFSv4
Commit 9a11899c5e (USB: OHCI: add missing PCI PM callbacks to
ohci-pci.c) added missing ohci_suspend and ohci_resume callback
pointers, but forgot that these callbacks are declared and defined
only when CONFIG_PM is enabled.
This patch adds a preprocessor conditional to avoid build errors when
PM is disabled.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Meelis Roos <mroos@linux.ee>,
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In suspend-resume sequence, the OS could attempt to initialize the controller
before it is ready, check for POST state before going ahead.
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver core clears the driver data to NULL after device_release or on probe
failure, so just remove it from here.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current FSI is supporting DMAEngine transfer,
but, it needs to use work queue.
Therefore, DMA transfer settings might be late if there is heavy task.
This patch reserves next period beforehand on DMA transfer function.
Android sound will be breaking up without this patch.
Tested-by: Tomohito Esaki <etom@igel.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove the "====" pattern to let the comments cleaner and more uniform.
Also, do not use multi-line style for a single line comment.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
