The Kconfig symbols OMAP_PACKAGE_ZAC and OMAP_PACKAGE_ZAF were added in
v2.6.36. They have never been used. Setting them has no effect. These
symbols can safely be removed.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
[tony@atomide.com: updated to remove also the related mux.h entries]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SyncTimer in AM43x is clocked using the following two sources:
1) An inaccuarte 32k clock (CLK_32KHZ) derived from PER DPLL, causing system
time to go slowly (~10% deviation).
2) external 32KHz RTC clock, which may not always be available on board like
in the case of ePOS EVM
Use gptimer as clocksource instead, as is done in the case of AM335x
(which does not have a SyncTimer). With this, system time keeping works
accurately.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Determine AM43x device features by reusing AM335x helper as feature
register layout is similar.
And also exporting AM43xx family name.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
sbc-t3x boards features two external USB ports on SB-T35 baseboard.
The baseboardi USB hub reset signal should be de-asserted to make
those ports functional.
sbc-t3517 features additional (assembled on CoM) USB hub which also
requires reset signal handling.
Add quirks code to handle proper reset pulse signal.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for CM-T3517 CoM and SBC-T3517 board.
reused common support for sbc-t3x boards
(omap3-cm-t3x.dtsi, omap3-sb-t35.dtsi):
* SB-T35 baseboard eth
* MMC1, UART3
* HS USB Port 1/2
* I2C1/3
* Heartbit led
Added basic support for:
* MMC1 wp/cd signals
* CM-T3517 Usb Hub
* WL12xx WiFi chip
* Davinci EMAC
* AM35X OTG
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for CM-T3530 CoM and SBC-T3530 board.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap3_noncore_dpll_set_rate forces a reparent to the same clk_ref
for every call that takes place. This is an can be done only if a change
is detected.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Printing with unsigned long rates with %ld gives wrong result if the
rate is high enough. Fix this by using %lu.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
AM43xx has a spinlock module which is identical to the
one present on AM33xx. Register the spinlock ocp_if link
so that the spinlock hwmod and associated omap_device can
be instantiated, and the runtime pm API could be used by
the OMAP hwspinlock driver.
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Since commit 65aa94b204 (ARM: OMAP4: clockdomain/CM code: Update supported
transition modes), on OMAP4, all CLKDMs support HW_AUTO so this is used
instead of SW_SLEEP for the idling of clockdomains. However, additional
SoCs now leverage the OMAP4 clockdomain code so update it to use SW_SLEEP
if the clockdomain data specifies that the CLKDM has the
CLKDM_CAN_FORCE_SLEEP flag set rather than using HW_AUTO for both cases.
Without this patch, clockdomain handling is broken on AM43xx and no
clockdomains are actually being put into idle on this platform. Any
attempt to idle them results in the HW_AUTO value (0x3) being written
to them with no apparent effect.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[paul@pwsan.com: added extra explanatory text from patch set intro]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add restart hook so that AM4372 builds can restart the platform.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Move the power GPIO handling from the board code into
the driver. This is a dependency for device tree support.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the wl1251 part of the wl12xx platform data structure into a new
structure specifically for wl1251. Change the platform data built-in
block and board files accordingly.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Sebastian Reichel <sre@debian.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
of individual platforms as they are redundant.
- Make SMP, CACHE_L2X0 and GPIO config options user visible on
multi-platform builds as most platforms enable these options and all
platforms can run with them enabled.
- Make multi-platform v6 default to more optimal v6k rather than v6
- Remove the last bit of mach-virt and convert it to just a kconfig
option.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJTBT1nAAoJEMhvYp4jgsXikI0IAIv2GmBCgbg0XhHZBSheSNOh
Th1bv4KeEci/3uezwVTAA3AtJIvDNMAQjRYjNSyOnCCC7s5czex1w/Mk/6IzgX8C
eCauM5kiOV3ZKPMbPI6gxg0bmFe+YzWREbm7fpAqxpc3IXwzYlShnq/kKISq25Qj
mRZtv97AB2xqAy9zTyy18y+c+F/1mAgd+NeiDbjBimHbTK4urjiD7PpcWvmbYZld
H9Qw4d9JwVTRpRHw9PRR9glnvFYiFpp+s9ehSjcyYi8wjZKO1+67c56fS+ScsoV7
qM4J2qtS2kpzvyFvOI7wY6E2M5Es7zOeuJAmh0jEkbDtRa0a4YFYL0DAp5k9Xiw=
=NEez
-----END PGP SIGNATURE-----
Merge tag 'kconfig-cleanup-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux into next/cleanup
Merge "kconfig clean-up and mach-virt removal for 3.15" from Rob Herring
- Remove common kconfig options required by multi-platform builds out
of individual platforms as they are redundant.
- Make SMP, CACHE_L2X0 and GPIO config options user visible on
multi-platform builds as most platforms enable these options and all
platforms can run with them enabled.
- Make multi-platform v6 default to more optimal v6k rather than v6
- Remove the last bit of mach-virt and convert it to just a kconfig
option.
* tag 'kconfig-cleanup-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
ARM: virt: select ARM_AMBA
ARM: virt: make mach-virt just a kconfig option
ARM: vt8500: enable V6K instead of plain V6
ARM: cns3xxx: enable V6K instead of plain V6
ARM: bcm2835: enable V6K instead of plain V6
ARM: Select V6K instead of V6 by default for multi-platform
ARM: select MIGHT_HAVE_CACHE_L2X0 for V6 and V7 multi-platform
ARM: select HAVE_SMP for V7 multi-platform
ARM: centralize common multi-platform kconfig options
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
and random crashes if booting n900 with device tree and
thumb mode. Also few other regressions and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQIcBAABAgAGBQJTD9JgAAoJEBvUPslcq6VzKMcP/05G4FO3Z0VAqvysVZSkcqsm
n7g/ayi5PYDyWu8idPTg+5YmIWDl8rp8QCiPcRivlSABCiqHG5+I+qyeE3Wq0gVH
9BfBkWqkHtrmCmGofO3dLACAqstG7tzaIhfAziOME5kolYv4P4Pb/9FqIxEUYvGD
NDh+skwYQ/C4ZNPZbx04kCNuN/FdotJ9W9SZeriuHi1buV9pHtMXU38avbrj0VVF
YDl6RgyiVJloAnI6WLTiZ6fYf0hbb0WVZk6m0qciFdQG5X3vzCry2VCFYyXh7Ex7
vuJ40HQAKtCPP4zsWQH0pscL1EKpXpZnGZsRAjO3Gxu8LOme336DAisWU5qmbNox
TaPLQ8oA9WenwjeoUY3Pr8rt1EfIzlFmTW21+E1lij8QEgbVcF3FJu+57CtblVxw
vN79X3EN+ufxQImfuX8pUJ7o3vIqMtALAz7YcxSgyFIko/KiMLILyPwGKG0uQf4R
igoyuzXtGnUXx7KPr1BjuBnd6BFa4OPFoLGzYXP7mjmpL9ddXu2tQxdKR+ssSBaA
1MpeA3NkWMi9L0u51HBt/8WCt/ZcJnxl/rRHmhtNvtTZ/uLy4R/3ptPFj8ds3WYZ
BIIAmGEpgC6V7APasGt0W3ok78Q1LTOAP0WY+AZEaZNPryGjIfZc4DSohzavknVZ
Zri9UxByEIu4YFsYX84D
=2y5d
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.14/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Omap fixes from Tony Lindgren:
Fixes for omaps mostly to fix the 3430 display regression,
and random crashes if booting n900 with device tree and
thumb mode. Also few other regressions and fixes.
* tag 'omap-for-v3.14/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: Fix pinctrl interrupts for core2
ARM: OMAP: Kill warning in CPUIDLE code with !CONFIG_SMP
ARM: OMAP2+: Add support for thumb mode on DT booted N900
ARM: OMAP2+: clock: fix clkoutx2 with CLK_SET_RATE_PARENT
ARM: OMAP4: hwmod: Fix SOFTRESET logic for OMAP4
ARM: DRA7: hwmod data: correct the sysc data for spinlock
ARM: OMAP5: PRM: Fix reboot handling
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The omapdss driver no longer uses get_context_loss_count call, so we can
remove it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
After splitting padconf core into two parts to avoid exposing
unaccessable registers, the new padconf core2 domain was left
without a wake-up interrupt.
Fix the issue by passing the shared wake-up interrupt in
platform data like we do for padconf core and wkup domains
already.
Fixes: 3d49538364 (ARM: dts: Split omap3 pinmux core device)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Delete ARM's asm/system.h. It's the last holdout and should be got rid of.
This builds for defconfig, lpc32xx_defconfig, exynos_defconfig + XEN, the
previous changed to a Gemini system and an omap3 config with TI_DAVINCI_EMAC.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The camera sensor will soon require regulators and clocks. Register
fixed regulators for its VAA and VDD power supplies and a fixed rate
clock for its master clock.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=g6PN
-----END PGP SIGNATURE-----
Merge tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux
This cleanup series gets rid of <mach/timex.h> for platforms not using
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
Conflicts:
arch/arm/mach-at91/at91sam9260.c
arch/arm/mach-at91/at91sam9261.c
arch/arm/mach-at91/at91sam9263.c
arch/arm/mach-at91/at91sam9rl.c
arch/arm/mach-mmp/time.c
arch/arm/mach-sa1100/time.c
for non SMP build, NR_CPUS is 1 and hence the code complains with below
warnings.
arch/arm/mach-omap2/cpuidle44xx.c:207:8: warning: array subscript is above array bounds [-Warray-bounds]
arch/arm/mach-omap2/cpuidle44xx.c:212:11: warning: array subscript is above array bounds [-Warray-bounds]
Kill it by making array size fixed.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without enabling the workaround for ARM errata 430973 thumb
compiled userland crashes randomly on the Nokia N900.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
reboot fix in there, plus a clock fix for rate computations involving
x2 multipliers.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/prcm-fixes-a-v3.14-rc/20140219131753/
Note that most full-chip PM is broken since the v3.14 merge; it's
not caused by this series.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aMQk
-----END PGP SIGNATURE-----
Merge tag 'for-v3.14-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.14/fixes
Several OMAP clock/PM/device data fixes for v3.14-rc. There's an OMAP5
reboot fix in there, plus a clock fix for rate computations involving
x2 multipliers.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/prcm-fixes-a-v3.14-rc/20140219131753/
Note that most full-chip PM is broken since the v3.14 merge; it's
not caused by this series.
All V7 platforms can run SMP kernels, so make CONFIG_SMP visible for V7
multi-platform builds.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Multi-platform requires various kconfig options to be selected, so
platforms don't need to select them individually.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
If CLK_SET_RATE_PARENT is set for a clkoutx2 clock, calling
clk_set_rate() on the clock "skips" the x2 multiplier as there are no
set_rate and round_rate functions defined for the clkoutx2.
This results in getting double the requested clock rates, breaking the
display on omap3430 based devices. This got broken when
d0f58bd3bb and related patches were merged
for v3.14, as omapdss driver now relies more on the clk-framework and
CLK_SET_RATE_PARENT.
This patch implements set_rate and round_rate for clkoutx2.
Tested on OMAP3430, OMAP3630, OMAP4460.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 313a76e (ARM: OMAP2+: hwmod: Fix SOFTRESET logic) introduced
softreset bit cleaning right after set one. It is caused L3 error for
OMAP4 ISS because ISS register write occurs when ISS reset process is in
progress. Avoid this situation by cleaning softreset bit later, when reset
process is successfully finished.
Signed-off-by: Illia Smyrnov <illia.smyrnov@globallogic.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The spinlock module's SYSCONFIG register on DRA7xx does not
support smart wakeup, and also does not have the CLKACTIVITY
field. The sysc data for spinlock module has been appropriately
fixed up to reflect the same.
Cc: Ambresh K <ambresh@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Use the correct register offset for issuing the
reset command in OMAP5. Since dev_inst is set dynamically
OMAP4 should not be affected by this change.
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@gmail.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=g6PN
-----END PGP SIGNATURE-----
Merge tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux into next/cleanup
This cleanup series gets rid of <mach/timex.h> for platforms not using
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
* tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux:
ARM: ixp4xx: fix timer latch calculation
ARM: drop <mach/timex.h> for !ARCH_MULTIPLATFORM, too
ARM: rpc: stop using <mach/timex.h>
ARM: ixp4xx: stop using <mach/timex.h>
input: ixp4xx-beeper: don't use symbols from <mach/timex.h>
ARM: at91: don't use <mach/timex.h>
ARM: ep93xx: stop using mach/timex.h
ARM: mmp: stop using mach/timex.h
ARM: netx: stop using mach/timex.h
ARM: sa1100: stop using mach/timex.h
clocksource: sirf/marco+prima2: drop usage of CLOCK_TICK_RATE
rtc: pxa: drop unused #define TIMER_FREQ
rtc: at91sam9: include <mach/hardware.h> explicitly
ARM/serial: at91: switch atmel serial to use gpiolib
Signed-off-by: Olof Johansson <olof@lixom.net>
USB_ARCH_HAS_EHCI, USB_ARCH_HAS_OHCI, and USB_ARCH_HAS_XHCI were just
removed. Selecting them is a nop. The select statements for these
symbols can be removed too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 97411608fd ("ARM: OMAP2+: Remove legacy support for zoom
platforms") removed the Kconfig symbols MACH_OMAP_ZOOM2 and
MACH_OMAP_ZOOM3. Remove the last usage of the related macros too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The last caller of machine_is_nokia_n800() was removed in commit
5a87cde490 ("ARM: OMAP2+: Remove legacy booting support for n8x0").
That means that the Kconfig symbol MACH_NOKIA_N800 is now unused. It can
safely be removed.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes: commit 75d3625e0e
ARM: OMAP2+: gpmc: add DT bindings for OneNAND
OMAP SoC(s) depend on GPMC controller driver to parse GPMC DT child nodes and
register them platform_device for ONENAND driver to probe later. However this does
not happen if generic MTD_ONENAND framework is built as module (CONFIG_MTD_ONENAND=m).
Therefore, when MTD/ONENAND and MTD/ONENAND/OMAP2 modules are loaded, they are unable
to find any matching platform_device and remain un-binded. This causes on board
ONENAND flash to remain un-detected.
This patch causes GPMC controller to parse DT nodes when
CONFIG_MTD_ONENAND=y || CONFIG_MTD_ONENAND=m
CC: <stable@vger.kernel.org> # 3.9.x+
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes: commit bc6b1e7b86
ARM: OMAP: gpmc: add DT bindings for GPMC timings and NAND
OMAP SoC(s) depend on GPMC controller driver to parse GPMC DT child nodes and
register them platform_device for NAND driver to probe later. However this does
not happen if generic MTD_NAND framework is built as module (CONFIG_MTD_NAND=m).
Therefore, when MTD/NAND and MTD/NAND/OMAP2 modules are loaded, they are unable
to find any matching platform_device and remain un-binded. This causes on board
NAND flash to remain un-detected.
This patch causes GPMC controller to parse DT nodes when
CONFIG_MTD_NAND=y || CONFIG_MTD_NAND=m
CC: <stable@vger.kernel.org> # 3.9.x+
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP5, DRA7, AM43xx all have OPPs. So select the same to allow SoC
only configuration boot to work with OPP.
Reported-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The wakeup gen mask/unmask callback uses the irq element of the
irq_data to setup. The irq is the linux virtual irq number and
is same as the hardware irq number only when the parent irqchip
is setup as a legacy domain. When it is used as a linear domain,
the virtual irqs are allocated dynamically and wakeup gen code
cannot rely on these numbers to access the irq registers. Instead
use the hwirq element of the irq_data which represent the physical
irq number.
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The selection of HAVE_ARM_TWD for OMAP and shmobile depend on LOCAL_TIMER
which no longer exists. They should depend on SMP instead.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Here's a set of patches for (hopefully) -rc1. Some of them are fixes,
but a good number of them also do things such as enable new drivers in
the defconfigs for platforms that have such devices, increases coverage
of the multiplatform defconfig and some DTS changes that plumbs up some
of the devices that now have bindings and driver support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ymAC
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's a set of patches for (hopefully) -rc1. Some of them are fixes,
but a good number of them also do things such as enable new drivers in
the defconfigs for platforms that have such devices, increases
coverage of the multiplatform defconfig and some DTS changes that
plumbs up some of the devices that now have bindings and driver
support.
The commit dates are recent; we've mostly collected these fixes in the
last few days but I also had to rebuild the branch yesterday to sort
out some internal conflicts which reset the timestamps. The changes
should have been tested by each platform maintainer already (and few
of them have cross-platform impact) so I'm personally not too
concerned by it at this time"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
ARM: multi_v7_defconfig: remove redundant entries and re-enable TI_EDMA
ARM: multi_v7_defconfig: add mvebu drivers
clocksource: kona: Add basic use of external clock
drivers: bus: fix CCI driver kcalloc call parameters swap
ARM: dts: bcm28155-ap: Fix Card Detection GPIO
ARM: multi_v7_defconfig: Select CONFIG_AT803X_PHY
ARM: keystone: config: fix build warning when CONFIG_DMADEVICES is not set
MAINTAINERS: ARM: SiRF: use regex patterns to involve all SiRF drivers
ARM: dts: zynq: Add SDHCI nodes
ARM: hisi: don't select SMP
ARM: tegra: rebuild tegra_defconfig to add DEBUG_FS
ARM: multi_v7: copy most options from tegra_defconfig
ARM: iop32x: fix power off handling for the EM7210 board
ARM: integrator: restore static map on the CP
ARM: msm_defconfig: Enable MSM clock drivers
ARM: dts: msm: Add clock controller nodes and hook into uart
ARM: OMAP4+: move errata initialization to omap4_pm_init_early
ARM: OMAP4460: cpuidle: Extend PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD on cpuidle
ARM: mvebu: fix compilation warning on Armada 370 (i.e. non-SMP)
ARM: shmobile: r8a7790.dtsi: ficx i2c[0-3] clock reference
...
Move all OMAP4 PM errata initializations to centralized location in
omap4_pm_init_early. This allows for users to utilize the erratas
in various submodules as needed.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The same workaround as ff999b8a09
"ARM: OMAP4460: Workaround for ROM bug because of CA9 r2pX GIC ..."
need to be applied not only when system is booting, but when MPUSS hits
OSWR state through CPUIdle too. Without this WA the same issue is
reproduced now on boards PandaES and Tablet/Blaze with SOM OMAP4460
when CONFIG_CPU_IDLE is enabled.
After MPUSS has enterred OSWR and waken up:
- GIC distributor became disabled forever
- scheduling is not performed any more
Cc: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reported-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull media updates from Mauro Carvalho Chehab:
- a new jpeg codec driver for Samsung Exynos (jpeg-hw-exynos4)
- a new dvb frontend for ds2103 chipset (m88ds2103)
- a new sensor driver for Samsung S5K5BAF UXGA (s5k5baf)
- new drivers for R-Car VSP1
- a new radio driver: radio-raremono
- a new tuner driver for ts2022 chipset (m88ts2022)
- the analog part of em28xx is now a separate module that only
load/runs if the device is not a pure digital TV device
- added a staging driver for bcm2048 radio devices
- the omap 2 video driver (omap24xx) was moved to staging. This driver
is for an old hardware and uses a deprecated Kernel internal API. If
nobody cares enough to fix it, it would be removed on a couple Kernel
releases
- the sn9c102 driver was moved to staging. This driver was replaced by
gspca, and disabled on some distros, as almost all devices are known
to work properly with gspca. It should be removed from kernel on a
couple Kernel releases
- lots of driver fixes, improvements and cleanups
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (421 commits)
[media] media: v4l2-dev: fix video device index assignment
[media] rc-core: reuse device numbers
[media] em28xx-cards: properly initialize the device bitmap
[media] Staging: media: Fix line length exceeding 80 characters in as102_drv.c
[media] Staging: media: Fix line length exceeding 80 characters in as102_fe.c
[media] Staging: media: Fix quoted string split across line in as102_fe.c
[media] media: st-rc: Add reset support
[media] m2m-deinterlace: fix allocated struct type
[media] radio-usb-si4713: fix sparse non static symbol warnings
[media] em28xx-audio: remove needless check before usb_free_coherent()
[media] au0828: Fix sparse non static symbol warning
Revert "[media] go7007-usb: only use go->dev after allocated"
[media] em28xx-audio: provide an error code when URB submit fails
[media] em28xx: fix check for audio only usb interfaces when changing the usb alternate setting
[media] em28xx: fix usb alternate setting for analog and digital video endpoints > 0
[media] em28xx: make 'em28xx_ctrl_ops' static
em28xx-alsa: Fix error patch for init/fini
[media] em28xx-audio: flush work at .fini
[media] drxk: remove the option to load firmware asynchronously
[media] em28xx: adjust period size at runtime
...
dominated by platform support for Qualcomm's MSM SoCs, DT binding
updates for TI's OMAP-ish processors and additional support for Samsung
chips. Additionally there are other smaller clock driver changes and
several last minute fixes. This pull request also includes the HiSilicon
support that depends on the already-merged arm-soc pull request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=WRJD
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.14-part2' of git://git.linaro.org/people/mike.turquette/linux
Pull more clock framework changes from Mike Turquette:
"The second half of the clock framework pull requeust for 3.14 is
dominated by platform support for Qualcomm's MSM SoCs, DT binding
updates for TI's OMAP-ish processors and additional support for
Samsung chips.
Additionally there are other smaller clock driver changes and several
last minute fixes. This pull request also includes the HiSilicon
support that depends on the already-merged arm-soc pull request"
[ Fix up stupid compile error in the source tree with evil merge - Grumpy Linus ]
* tag 'clk-for-linus-3.14-part2' of git://git.linaro.org/people/mike.turquette/linux: (49 commits)
clk: sort Makefile
clk: sunxi: fix overflow when setting up divided factors
clk: Export more clk-provider functions
dt-bindings: qcom: Fix warning with duplicate dt define
clk: si5351: remove variant from platform_data
clk: samsung: Remove unneeded semicolon
clk: qcom: Fix modular build
ARM: OMAP3: use DT clock init if DT data is available
ARM: AM33xx: remove old clock data and link in new clock init code
ARM: AM43xx: Enable clock init
ARM: OMAP: DRA7: Enable clock init
ARM: OMAP4: remove old clock data and link in new clock init code
ARM: OMAP2+: io: use new clock init API
ARM: OMAP2+: PRM: add support for initializing PRCM clock modules from DT
ARM: OMAP3: hwmod: initialize clkdm from clkdm_name
ARM: OMAP: hwmod: fix an incorrect clk type cast with _get_clkdm
ARM: OMAP2+: clock: use driver API instead of direct memory read/write
ARM: OMAP2+: clock: add support for indexed memmaps
ARM: dts: am43xx clock data
ARM: dts: AM35xx: use DT clock data
...
This branch is reducing in size for every release since most board-related
changes have started happening in devicetrees now. Still, we have some things
going on here.
* Renesas platforms are still adding a bit more legacy device support, something
that should trail off shortly as they move to full DT.
* We group most defconfig updates into this branch out of old habits
* Removal of legacy OMAP2 platforms over to DT continues, and a handful of old
code is being removed here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wLdE
-----END PGP SIGNATURE-----
Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"This branch is reducing in size for every release since most
board-related changes have started happening in devicetrees now.
Still, we have some things going on here.
* Renesas platforms are still adding a bit more legacy device
support, something that should trail off shortly as they move to
full DT
* We group most defconfig updates into this branch out of old habits
* Removal of legacy OMAP2 platforms over to DT continues, and a
handful of old code is being removed here"
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: dts: OMAP2: fix interrupt number for rng
ARM: dts: Split omap3 pinmux core device
ARM: dts: Add omap specific pinctrl defines to use padconf addresses
ARM: bcm2835: bcm2835_defconfig updates
ARM: msm_defconfig: Enable restart driver
defconfig: msm_defconfig: Enable CONFIG_ARCH_MSM8974
ARM: msm: Add support for APQ8074 Dragonboard
ARM: exynos_defconfig: Enable S2MPS11 voltage regulator
ARM: tegra: Enable DRM panel support
ARM: shmobile: mackerel: Fix USBHS pinconf entry
ARM: shmobile: Let Koelsch multiplatform boot with Koelsch DTB
ARM: shmobile: Let Lager multiplatform boot with Lager DTB
ARM: shmobile: Remove non-multiplatform Koelsch reference support
ARM: shmobile: Remove non-multiplatform Lager reference support
ARM: shmobile: koelsch-reference: Instantiate clkdevs for SCIF and CMT
ARM: shmobile: lager-reference: Instantiate clkdevs for SCIF and CMT
ARM: shmobile: koelsch-reference: Remove duplicate CCF initialization
ARM: shmobile: lager-reference: Enable multiplaform kernel support
ARM: shmobile: armadillo: Set backlight enable GPIO
ARM: shmobile: Koelsch: add Ether support
...
Conflicts:
arch/arm/mach-omap2/omap_hwmod_2xxx_ipblock_data.c
New core SoC-specific changes.
New platforms:
* Introduction of a vendor, Hisilicon, and one of their SoCs with some
random numerical product name.
* Introduction of EFM32, embedded platform from Silicon Labs (ARMv7m, i.e. !MMU).
* Marvell Berlin series of SoCs, which include the one in Chromecast.
* MOXA platform support, ARM9-based platform used mostly in industrial products
* Support for Freescale's i.MX50 SoC.
Other work:
* Renesas work for new platforms and drivers, and conversion over to
more multiplatform-friendly device registration schemes.
* SMP support for Allwinner sunxi platforms.
* ... plus a bunch of other stuff across various platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pgLW
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New core SoC-specific changes.
New platforms:
* Introduction of a vendor, Hisilicon, and one of their SoCs with
some random numerical product name.
* Introduction of EFM32, embedded platform from Silicon Labs (ARMv7m,
i.e. !MMU).
* Marvell Berlin series of SoCs, which include the one in Chromecast.
* MOXA platform support, ARM9-based platform used mostly in
industrial products
* Support for Freescale's i.MX50 SoC.
Other work:
* Renesas work for new platforms and drivers, and conversion over to
more multiplatform-friendly device registration schemes.
* SMP support for Allwinner sunxi platforms.
* ... plus a bunch of other stuff across various platforms"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (201 commits)
ARM: tegra: fix tegra_powergate_sequence_power_up() inline
ARM: msm_defconfig: Update for multi-platform
ARM: msm: Move MSM's DT based hardware to multi-platform support
ARM: msm: Only build timer.c if required
ARM: msm: Only build clock.c on proc_comm based platforms
ARM: ux500: Enable system suspend with WFI support
ARM: ux500: turn on PRINTK_TIME in u8500_defconfig
ARM: shmobile: r8a7790: Fix I2C controller names
ARM: msm: Simplify ARCH_MSM_DT config
ARM: msm: Add support for MSM8974 SoC
ARM: sunxi: select ARM_PSCI
MAINTAINERS: Update Allwinner sunXi maintainer files
ARM: sunxi: Select RESET_CONTROLLER
ARM: imx: improve the comment of CCM lpm SW workaround
ARM: imx: improve status check of clock gate
ARM: imx: add necessary interface for pfd
ARM: imx_v6_v7_defconfig: Select CONFIG_REGULATOR_PFUZE100
ARM: imx_v6_v7_defconfig: Select MX35 and MX50 device tree support
ARM: imx: Add cpu frequency scaling support
ARM i.MX35: Add devicetree support.
...
