Re-initialize the target when fw crash is reported.
This would make the device functional again after
target crash. During the target re-initialization
it is made sure that target is not bugged with data/cmd
request, ar->state ATH6KL_STATE_RECOVERY is used
for this purpose.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
a minor cleanup in assigning the driver specific network type
based on interface type.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since WOW_MASK_SIZE and WOW_PATTERN_SIZE have the same value, are
logically equivalent, and part of the WMI API so therefore unlikely to
change, consolidate these into WOW_PATTERN_SIZE.
Reported-by Kalle Valo <kvalo@qualcomm.com>
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch reflects changes in the firmware scheduled scan
implementation to behave better in cases with multiple concurrent vifs.
Major changes:
- scheduled scan filters and state are now programmed per-vif.
- decouple scheduled scan from host sleep.
To maintain graceful failure with old firmwares, a new firmware
capability bit is introduced: ATH6KL_FW_CAPABILITY_SCHED_SCAN_V2.
ath6kl simply won't advertise scheduled scan to cfg80211 if the
SCHED_SCAN_V2 is not supported.
Since firmwares from here on out won't support the previous implicit API
for scheduled scan (set WoW filters and host sleep), bump the firmware
API to protect old drivers.
Unfortunately, due to firmware RAM constraints ath6kl still cannot
expect a scan complete event at the end of a scheduled scan results
cycle, so the sched_scan_timer is retained.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If the firmware decides to initiate a channel switch on an AP vif
running an RSN BSS, reconfigure the saved RSN IE capabilities as well.
Fixes a bug where the beacon and 4-way handshake would have a capability
mismatch after a channel switch, since the firmware apparently clears
these on an AP disconnect.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Only WoW filters for the first vif were being set, causing failures to
wake up on any concurrent connected vifs. Handle all per-vif suspend
and resume tasks.
Since cfg80211 issues user wow filters on a per-wiphy basis, set any
custom filters on all connected vifs.
Starting WoW in firmware and setting host sleep mode is still handled on
a global per-phy level. The first vif is always used for bookkeeping
regardless of whether it is connected or not.
WoW is cancelled if no connected vifs are found.
No firmware capability bits or API bump is needed for this patch, as
setting filters for vifs with index > 0 will simply overwrite the index
0 filters in the current implementation. While not correct, this is
identical to the existing behavior.
kvalo: fix a checkpatch warning in ath6kl_wow_resume()
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To make it possible to change the country code from user space via nl80211
add handler for reg_notifier. The feature is only enabled when built
time option CONFIG_ATH6KL_REGDOMAIN is enabled, which again depends on
CFG80211_CERTIFICATION_ONUS for certication purposes.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ATH6KL_FW_CAPABILITY_STA_P2PDEV_DUPLEX was checked in cfg80211.c which is
a bit awkward when adding more callsites to the scan functions. Refactor
the code to wmi.c so that it's transparent to the callers.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath6kl firmware can monitor a connection and report when a certain
TX failure threshold is crossed. Support this configuration and event
reporting on compatible firmwares.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware and driver generate MAC addresses for the second and third interfaces.
In addition to the existing algorithm, flip bit 7 of 5th octet. Since both
firmware and driver individually generate the MAC addresses, introduce a new
firmware capability bit to keep them compatible.
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath6kl firmware can filter scan results based on rssi. This is
useful to limit hosts wakeups on scheduled scans.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The include file linux/ieee80211.h contains three definitions for
the same thing in enum ieee80211_eid due to historic changes:
/* Information Element IDs */
enum ieee80211_eid {
:
WLAN_EID_WPA = 221,
WLAN_EID_GENERIC = 221,
WLAN_EID_VENDOR_SPECIFIC = 221,
:
};
The standard refers to this as "vendor specific" element so the
other two definitions are better not used. This patch changes the
wireless drivers to use one definition, ie. WLAN_EID_VENDOR_SPECIFIC.
Cc: Jouni Malinen <j@w1.fi>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath6kl]
Acked-by: Bing Zhao <bzhao@marvell.com> [mwifiex]
Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com> [ipw2x00]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[change libipw as well]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The next patch will introduce a flag that is set
by default in cfg80211 so drivers and mac80211
need to use |= to set features they have so that
they don't clear the already-set feature.
We could set the flag in wiphy_register() instead
of wiphy_new() to avoid this patch, but then the
drivers couldn't *unset* flags they don't want to
use even though the implementation is generic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new P2P Device will have to be able to scan for
P2P search, so move scanning to use struct wireless_dev
instead of struct net_device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to be able to create P2P Device wdevs, move
the virtual interface management over to wireless_dev
structures.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The management frame and remain-on-channel APIs will be
needed in the P2P device abstraction, so move them over
to the new wdev-based APIs. Userspace can still use both
the interface index and wdev identifier for them so it's
backward compatible, but for the P2P Device wdev it will
be able to use the wdev identifier only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When CONFIG_PM is disabled, no device can possibly
support WoWLAN since it can't go to sleep to start
with. Due to this, mac80211 had even rejected the
hardware registration. By making all the code and
data for WoWLAN depend on CONFIG_PM we can promote
this runtime error to a compile-time error.
Add #ifdef around all WoWLAN code to remove it in
systems that don't need it as they never suspend.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support for dtim_period configuration in beacon.
kvalo: add a comment about ignoring the error, use vif_idx,
add \n to the warning message
Signed-off-by: Etay Luz <eluz@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Messages without newlines can be interleaved.
Avoid this by adding terminations.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Instead of setting the channel first and then
starting the AP, let cfg80211 store the channel
and provide it as one of the AP settings.
This means that now you have to set the channel
before you can start an AP interface, but since
hostapd/wpa_supplicant always do that we're OK
with this change.
Alternatively, it's now possible to give the
channel as an attribute to the start-ap nl80211
command, overriding any preset channel.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In virtual interface structure, for each band separate ht cap
is needed. so that one can disable or enable ht capability band
wise.
This will fix the following issue:
1) Disable 11n from supplicant and start a P2P GO.
2) In beacon frames no HT-CAP IE is seen which is expected.
3) Now remove the P2P GO and kill the supplicant.
4) Beacon stops
5) Now using iw associate to an external AP in 5 GHZ
6) In 5 GHZ no HT IE going in assoc request but
when associated in 2.4 GHZ can see HT IES over the air
in assoc request.
In the code for del_beacon in cfg80211.c,set_ht_cap is being
called first for 2.4 GHZ and then for 5 GHZ. When called
for the first time for 2.4 GHZ the enable flag will be set to true
and so when called for the second time for 5 GHZ it just returns
after checking the flag.
Also using this one can have different HT capabilities
per band (for example one may decide not to use 20/40 in 2.4 GHZ
but use it in 5 GHZ). So maintaining a single context is not ok.
it is true for even the enable/disable flag and other HT
capabilities as well
Signed-off-by: Kiran Reddy <c_lreddy@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tx legacy and mcs rateset can configured using iw for
2.4 and 5 bands. Add support for the same in driver.
kvalo: add an enum for the hw flags and rename the flag accordingly,
rename ath6kl_cfg80211_set_bitrate_mask() to a shorter version to make
it easier to indent
Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl would issue a wmi disconnect command in response to a remote
disconnect and return early without notifying cfg80211, only sending a
cfg80211_disconnected (with reason code always 3) in response to the
second disconnect firmware event.
Pass the right reason code to cfg80211 on the first disconnect instead.
This fixes at least one bug where a p2p client would stop trying to
connect after receiving a stale RSN deauth which was reported to
cfg80211 as GO leaving BSS.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Scheduled scan implementation was only taking probed list into
consideration. The matched list was dropped. This would cause
FW not to report the AP as the list never had that AP's SSID
populated. This was causing long connection time when supplicant
would just issue a wild card SSID in probed list. As a part of
this implementation, ath6kl driver would create a complete list
by taking both probed and matched list and pass it to FW. FW would
probe for the SSID that it needs to and would match against the
relevant SSIDS that is been configured.
kvalo: whitespace changes, less indentation in the for loop, use ++
Signed-off-by: Naveen Singh <navesing@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable enhanced bmiss detection if the firmware supports it. This
feature is only enabled on some firmwares since it comes with a power
cost.
Also add a few missing command ids to keep the enums straight.
kvalo: fix a compiler with ath6kl_err(), add few empty lines
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Infrastructure to enable Multicast WOW support based on
firmware capability added to the driver.This enables
different customers or chips to control this feature based
on firmware capability.
kvalo: Firmware capability infrastructure for multicast wow feature,
indetation fixes.
Signed-off-by: Naveen Gangadharan <ngangadh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The currently used firmware images support 16 SSIDs in the scan
request (indexes 0..15), so update the host driver to use the same
limit to allow some more SSIDs to be scanned per request. In addition,
change the max-index to max-SSIDs to make it easier to understand the
implementation and fix couple of off-by-one checks that could limit
the maximum number of entries too strictly.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
bss filter is configured to allow the frames from all the bss other
than the currenly connected one, this is done when a scan is requested
in connected state. There is no reason to filter out the currently
connected bss, configure the filter to allow all the bss. This would
fix the reporting of stale rssi of the current bss while scanning.
Reported-by: Naveen singh <navesing@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With firmwares which do not support rsn capability override
(ATH6KL_FW_CAPABILITY_RSN_CAP_OVERRIDE) from host would
cause 4-way handshake failure when HT cap is advertised.
To fix this, do not advertise HT cap with cfg80211 for
those fw.
kvalo: fix a checkpatch warning
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch enables all multicast packets in non suspend mode
and enable multicast filtering in wow suspend mode. This also
fixes a bug in multicast where the driver assumed disable
multicast-all command disabled/filtered all multicast
packets, which was wrong assumption, because firmware will
apply the programmed filter.
Multicast requirements
- Enable forward all multicast packets(no filtering) in
non suspend mode.
- Enable multicast filtering in wow suspend mode for both
AP and CLIENT.
kvalo: fix a checkpatch warning and drop unrelated newline removal
Signed-off-by: Naveen Gangadharan <ngangadh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath6kl fw does not have enough memory to support the WoW filters of
more than one vif. Disallow WoW suspend if this is the case.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now that we know the supported PHY capabilities, only restore supported
bands / HT capabilities in firmware when stopping AP.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently the supported bands are just hard coded in the driver.
However, the ath6kl FW will include its 11n and band capabilites in a
WMI_READY event. Handle this and report capabilites to cfg80211
accordingly.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Set max_scan_ssids and max_sched_scan_ssids to same value. These use the
same probed SSID list, so there is no point in using different maximum
number of SSIDs.
Clear probed SSID entries that are not used. This was already done for
sched_scan, but not for scan. Be consistent and clear the table for both
cases to avoid leaving bogus entries.
In addition, share the same function for setting the probed SSIDs for
scan and sched_scan paths. This fixes setting of wildcard SSID flag
(ANY_SSID_FLAG) and changes the scan path to use probed SSID index
consistently (i.e., start with 0 similarly to sched_scan; firmware
will handle the needed internal mapping).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl does not support Probe Response offloading for Interworking (IEEE
802.11u), so remove the incorrectly added capability flag for it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Background scan interval should not be modified while starting
schedule scanning as it changes the bg scan interval when connected to AP.
Use the currently configured interval instead.
kvalo: improve commit log
Signed-off-by: Subramania Sharma <sharmat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Added a new member bg_scan_period in struct ath6kl_vif
to retain background scan period value configured via debugfs
entry 'bgscan_interval'. This backup is needed in schedule scan
path while configuring scan parameters.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Aafter wlan interface is down WLAN_ENABLED flags will be cleared and
deepsleep_suspend function will be blocked in this senario. This patch
allows deepsleep_suspend function when wlan interface down by removed
the WLAN_ENABLED flag checking.
kvalo: fix commit log
Signed-off-by: Ming Jiang <mjiang@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently rsn capability is not set when it is not available in
rsn IE. Set it to 0 in firmware when it is not there in the ie to
make sure host and target are consistent.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
alignment is not taken care in accessing pairwise cipher and AKM suite
count which are parsed from rsn ie. Fix this alignment issue.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If an ath6kl AP vif is beaconing on one channel, and a STA vif
associates on a different channel, a WMI_DISCONNECT event will be sent
to the AP vif. Make the AP vif follow the STA interface, and notify
userspace.
kvalo: fix a sparse warning with vif->next_chan
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use a more current logging style.
Make sure all output is prefixed appropriately.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RSN capability field of RSN IE which is generated (which is what really
advertised in beacon/probe response) differs from the one generated in
wpa_supplicant. This inconsistency in rsn IE results in 4-way handshake
failure. To fix this, configure rsn capability used in wpa_supplicant
in firmware using a new wmi command, WMI_SET_IE_CMDID. There is a bit
(ATH6KL_FW_CAPABILITY_RSN_CAP_OVERRIDE) in fw_capabilities to advertise
this support to driver.
Signed-off-by: Subramania Sharma <sharmat@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch disables HT in start_ap if the type of the channel on
which the AP mode is going to be operating is non-HT. HT is enabled
with default ht cap setting if the operating channel is going to be
11n.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HT40 is not supported in 2.4Ghz.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
