On Power8 we can freeze PMC5 and 6 if we're not using them. Normally they
run all the time.
As noticed by Anshuman, we should unfreeze them when we disable the PMU
as there are legacy tools which expect them to run all the time.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
CC: <stable@vger.kernel.org> [v3.10]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In pmu_disable() we disable the PMU by setting the FC (Freeze Counters)
bit in MMCR0. In order to do this we have to read/modify/write MMCR0.
It's possible that we read a value from MMCR0 which has PMAO (PMU Alert
Occurred) set. When we write that value back it will cause an interrupt
to occur. We will then end up in the PMU interrupt handler even though
we are supposed to have just disabled the PMU.
We can avoid this by making sure we never write PMAO back. We should not
lose interrupts because when the PMU is re-enabled the overflowed values
will cause another interrupt.
We also reorder the clearing of SAMPLE_ENABLE so that is done after the
PMU is frozen. Otherwise there is a small window between the clearing of
SAMPLE_ENABLE and the setting of FC where we could take an interrupt and
incorrectly see SAMPLE_ENABLE not set. This would for example change the
logic in perf_read_regs().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
CC: <stable@vger.kernel.org> [v3.10]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A mistake we have made in the past is that we pull out the fields we
need from the event code, but don't check that there are no unknown bits
set. This means that we can't ever assign meaning to those unknown bits
in future.
Although we have once again failed to do this at release, it is still
early days for Power8 so I think we can still slip this in and get away
with it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
CC: <stable@vger.kernel.org> [v3.10]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Similar to the facility unavailble exception, except the facilities are
controlled by HFSCR.
Adapt the facility_unavailable_exception() so it can be called for
either the regular or Hypervisor facility unavailable exceptions.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
CC: <stable@vger.kernel.org> [v3.10]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The exception at 0xf60 is not the TM (Transactional Memory) unavailable
exception, it is the "Facility Unavailable Exception", rename it as
such.
Flesh out the handler to acknowledge the fact that it can be called for
many reasons, one of which is TM being unavailable.
Use STD_EXCEPTION_COMMON() for the exception body, for some reason we
had it open-coded, I've checked the generated code is identical.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
CC: <stable@vger.kernel.org> [v3.10]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
KVMTEST is a macro which checks whether we are taking an exception from
guest context, if so we branch out of line and eventually call into the
KVM code to handle the switch.
When running real guests on bare metal (HV KVM) the hardware ensures
that we never take a relocation on exception when transitioning from
guest to host. For PR KVM we disable relocation on exceptions ourself in
kvmppc_core_init_vm(), as of commit a413f47 "Disable relocation on
exceptions whenever PR KVM is active".
So convert all the RELON macros to use NOTEST, and drop the remaining
KVM_HANDLER() definitions we have for 0xe40 and 0xe80.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
CC: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have relocation on exception handlers defined for h_data_storage and
h_instr_storage. However we will never take relocation on exceptions for
these because they can only come from a guest, and we never take
relocation on exceptions when we transition from guest to host.
We also have a handler for hmi_exception (Hypervisor Maintenance) which
is defined in the architecture to never be delivered with relocation on,
see see v2.07 Book III-S section 6.5.
So remove the handlers, leaving a branch to self just to be double extra
paranoid.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
CC: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The topology update code that updates the cpu node registration in sysfs
should not be called while in stop_machine(). The register/unregister
calls take a lock and may sleep.
This patch moves these calls outside of the call to stop_machine().
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
the smp_release_cpus is a normal funciton and called in normal environments,
but it calls the __initdata spinning_secondaries.
need modify spinning_secondaries to match smp_release_cpus.
the related warning:
(the linker report boot_paca.33377, but it should be spinning_secondaries)
-----------------------------------------------------------------------------
WARNING: arch/powerpc/kernel/built-in.o(.text+0x23176): Section mismatch in reference from the function .smp_release_cpus() to the variable .init.data:boot_paca.33377
The function .smp_release_cpus() references
the variable __initdata boot_paca.33377.
This is often because .smp_release_cpus lacks a __initdata
annotation or the annotation of boot_paca.33377 is wrong.
WARNING: arch/powerpc/kernel/built-in.o(.text+0x231fe): Section mismatch in reference from the function .smp_release_cpus() to the variable .init.data:boot_paca.33377
The function .smp_release_cpus() references
the variable __initdata boot_paca.33377.
This is often because .smp_release_cpus lacks a __initdata
annotation or the annotation of boot_paca.33377 is wrong.
-----------------------------------------------------------------------------
Signed-off-by: Chen Gang <gang.chen@asianux.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A few new i2c-drivers came into the kernel which clear the clientdata-pointer
on exit or error. This is obsolete meanwhile, the core will do it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When error occurs, need return the related error code to let upper
caller know about it.
ppc_md.nvram_size() can return the error code (e.g. core99_nvram_size()
in 'arch/powerpc/platforms/powermac/nvram.c').
Also set ret value when only need it, so can save structions for normal
cases.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
cuda_init_via() is called from find_via_cuda() only, which is __init.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
This removes all the powerpc uses of the __cpuinit macros. There
are no __CPUINIT users in assembly files in powerpc.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This typedef is unnecessary and should just be removed.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This typedef is unnecessary and should just be removed.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pci_iommu_init() and pci_direct_iommu_init() are not referenced anywhere,
so remove them.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For an unknown relocation type since the value of r4 is just the 8bit
relocation type, the sum of r4 and r7 may yield an invalid memory
address. For example:
In normal case:
r4 = c00xxxxx
r7 = 40000000
r4 + r7 = 000xxxxx
For an unknown relocation type:
r4 = 000000xx
r7 = 40000000
r4 + r7 = 400000xx
400000xx is an invalid memory address for a board which has just
512M memory.
And for operations such as dcbst or icbi may cause bus error for an
invalid memory address on some platforms and then cause the board
reset. So we should skip the flush/invalidate the d/icache for
an unknown relocation type.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With pm81/pm91/pm121, when the overtemperature state is entered, and
when it remains on after skipped ticks, the driver will try to leave
it too soon (immediately on the next tick). This is because the active
FAILURE_OVERTEMP state is not visible in "new_failure" variable of the
current tick. Furthermore, the driver will keep trying to clear condition
in subsequent ticks as FAILURE_OVERTEMP remains set in the "last_failure"
variable. These will start to trigger WARNINGS from windfarm core:
[ 100.082735] windfarm: Clamping CPU frequency to minimum !
[ 100.108132] windfarm: Overtemp condition detected !
[ 101.952908] windfarm: Overtemp condition cleared !
[...]
[ 102.980388] WARNING: at drivers/macintosh/windfarm_core.c:463
[...]
[ 103.982227] WARNING: at drivers/macintosh/windfarm_core.c:463
[...]
[ 105.030494] WARNING: at drivers/macintosh/windfarm_core.c:463
[...]
[ 105.973666] WARNING: at drivers/macintosh/windfarm_core.c:463
[...]
[ 106.977913] WARNING: at drivers/macintosh/windfarm_core.c:463
Fix by adding a helper global variable. We leave the overtemp state only
after all failure bits have been cleared.
I saw this error on iMac G5 iSight (pm121). Also pm81/pm91 are fixed
based on the observation that these are almost identical/copy-pasted code.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, we're using the combo (PCI bus + devfn) in the PCI
config accessors and PCI config accessors in EEH depends on them.
However, it's not safe to refer the PCI bus which might have been
removed during hotplug. So we're using device node in the PCI
config accessors and the corresponding backends just reuse them.
The patch also fix one potential risk: We possiblly have frozen
PE during the early PCI probe time, but we haven't setup the PE
mapping yet. So the errors should be counted to PE#0.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch is for avoiding following build warnings:
The function .pnv_pci_ioda_fixup() references
the function __init .eeh_init().
This is often because .pnv_pci_ioda_fixup lacks a __init
The function .pnv_pci_ioda_fixup() references
the function __init .eeh_addr_cache_build().
This is often because .pnv_pci_ioda_fixup lacks a __init
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We needn't the the whole backtrace other than one-line message in
the error reporting interrupt handler. For errors triggered by
access PCI config space or MMIO, we replace "WARN(1, ...)" with
pr_err() and dump_stack(). The patch also adds more output messages
to indicate what EEH core is doing. Besides, some printk() are
replaced with pr_warning().
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On the PowerNV platform, the EEH address cache isn't built correctly
because we skipped the EEH devices without binding PE. The patch
fixes that.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have 2 fields in "struct pnv_phb" to trace the states. The patch
replace the fields with one and introduces flags for that. The patch
doesn't impact the logic.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
After reset (e.g. complete reset) in order to bring the fenced PHB
back, the PCIe link might not be ready yet. The patch intends to
make sure the PCIe link is ready before accessing its subordinate
PCI devices. The patch also fixes that wrong values restored to
PCI_COMMAND register for PCI bridges.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When the PHB is fenced or dead, it's pointless to collect the data
from PCI config space of subordinate PCI devices since it should
return 0xFF's. The patch also fixes overwritten buffer while getting
PCI config data.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Toralf Förster reported that the cpufreq ondemand governor behaves erratically
(doesn't scale well) after a suspend/resume cycle. The problem was that the
cpufreq subsystem's idea of the cpu frequencies differed from the actual
frequencies set in the hardware after a suspend/resume cycle. Toralf bisected
the problem to commit a66b2e5 (cpufreq: Preserve sysfs files across
suspend/resume).
Among other (harmless) things, that commit skipped the call to
cpufreq_update_policy() in the resume path. But cpufreq_update_policy() plays
an important role during resume, because it is responsible for checking if
the BIOS changed the cpu frequencies behind our back and resynchronize the
cpufreq subsystem's knowledge of the cpu frequencies, and update them
accordingly.
So, restore the call to cpufreq_update_policy() in the resume path to fix
the cpufreq regression.
Reported-and-tested-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: 3.10+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull another powerpc fix from Benjamin Herrenschmidt:
"I mentioned that while we had fixed the kernel crashes, EEH error
recovery didn't always recover... It appears that I had a fix for
that already in powerpc-next (with a stable CC).
I cherry-picked it today and did a few tests and it seems that things
now work quite well. The patch is also pretty simple, so I see no
reason to wait before merging it."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/eeh: Fix fetching bus for single-dev-PE
This is a set of seven bug fixes. Several fcoe fixes for locking problems,
initiator issues and a VLAN API change, all of which could eventually lead to
data corruption, one fix for a qla2xxx locking problem which could lead to
multiple completions of the same request (and subsequent data corruption) and
a use after free in the ipr driver. Plus one minor MAINTAINERS file update
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRy9qEAAoJEDeqqVYsXL0MIoUH/RkCyVWZqj2utTMXg0olPxm/
GE2OC5X944mBrMeY0wSfEj58NQoo9cRiXGTxZLl+X0lRHbTU4CCGUAAEu/0o5N/M
Gqtmk3Gn+iY819F0gYqs/En4IjLPsifonXaamHA1341NlNjDqb6IQdOQN8qjlfQT
aDebRuzS/z5jFO8pviem+GD2FDVSCdkM24SeJLxqxoyuOR77W/3n6bjlVY1jkCoI
lFA5k9OeqQRiEGqR+Da2nLWmCPt85R+qjNzxTqFmF2gh+Z/VW1hwAcjWz+/xSc4O
V7d/ZN9Qhk31PY3oQ1Q1jJU0fW95bqOo6dZvGrLkOVc1FkaFgjMF7RQuA8rVxRI=
=xWnQ
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of seven bug fixes. Several fcoe fixes for locking
problems, initiator issues and a VLAN API change, all of which could
eventually lead to data corruption, one fix for a qla2xxx locking
problem which could lead to multiple completions of the same request
(and subsequent data corruption) and a use after free in the ipr
driver. Plus one minor MAINTAINERS file update"
(only six bugfixes in this pull, since I had already pulled the fcoe API
fix directly from Robert Love)
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] ipr: Avoid target_destroy accessing memory after it was freed
[SCSI] qla2xxx: Fix for locking issue between driver ISR and mailbox routines
MAINTAINERS: Fix fcoe mailing list
libfc: extend ex_lock to protect all of fc_seq_send
libfc: Correct check for initiator role
libfcoe: Fix Conflicting FCFs issue in the fabric
This reverts commit 8d2f8cd424.
As reported by Stefan, this device already works with the parport_serial
driver, so the 8250_pci driver should not also try to grab it as well.
Reported-by: Stefan Seyfried <stefan.seyfried@googlemail.com>
Cc: Wang YanQing <udknight@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
codec->control_data has to be left unset to make the ASoC core access
the regmap properly.
That bug slipped in during a rebase session of the driver refactoring.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Replace calls to snd_soc_update_bits() with regmap_update_bits().
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is a DT only driver and st_pctl_of_match is always compiled
in. Hence of_match_ptr is unnecessary.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
When we treclaim and trecheckpoint there's an unavoidable period when r1
will not be a valid kernel stack pointer.
This patch clears the MSR recoverable interrupt (RI) bit over these
regions to indicate we have an invalid kernel stack pointer.
For treclaim, the region over which we clear MSR RI is larger than
required to avoid the need for an extra costly mtmsrd.
Thanks to Paulus for suggesting this change.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
String instruction emulation would erroneously result in a segfault if
the upper bits of the EA are set and is so high that it fails access
check. Truncate the EA to 32 bits if the process is 32-bit.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
While running Linux as guest on top of phyp, we possiblly have
PE that includes single PCI device. However, we didn't return
its PCI bus correctly and it leads to failure on recovery from
EEH errors for single-dev-PE. The patch fixes the issue.
Cc: <stable@vger.kernel.org> # v3.7+
Cc: Steve Best <sbest@us.ibm.com>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
