Enable HS-USB device for the Henninger board, defining the GPIO that the driver
should check when probing (which is the ID output from MAX3355 OTG chip).
Note that there will be pinctrl-related error messages if both internal PCI
and HS-USB drivers are enabled but they should be just ignored.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[Sergei: added pin function/group and prop, moved device node, fixed summary,
added changelog]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable HS-USB device for the Koelsch board, defining the GPIO that the driver
should check when probing (which is the ID output from MAX3355 OTG chip).
Note that there will be pinctrl-related error messages if both internal PCI
and HS-USB drivers are enabled but they should be just ignored.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[Sergei: added pin function/group and prop, moved device node, fixed summary,
added changelog]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the R8A7791 generic part of the HS-USB device node. It is up to the board
file to enable the device.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[Sergei: fixed summary, added changelog]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable HS-USB device for the Lager board, defining the GPIO that the driver
should check when probing. Since this board doesn't have the OTG ID pin, we
assume that GP5_18 (USB0_PWEN) is an ID pin because it is 1 when the SW5 is
in position 2-3 (meaning USB function) and 0 in other positions.
Note that there will be pinctrl-related error messages if both internal PCI
and HS-USB drivers are enabled but they should be just ignored.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[Sergei: added pin node and prop, moved device node, fixed summary, supplemented
changelog]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the R8A7790 generic part of the HS-USB device node.
It is up to the board file to enable the device.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[Sergei: fixed summary, added changelog]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since the PHY of USB3.0 and EHCI/OHCI ch2 are the same, the USB3.0
driver cannot use the phy driver when the EHCI/OHCI ch2 already used it:
phy phy-e6590100.usb-phy.3: phy init failed --> -16
xhci-hcd: probe of ee000000.usb failed with error -16
If so, we have to unbind the EHCI/OHCI ch2, and then we have to bind
the USB3.0 driver as the following:
echo 0000:02:02.0 > /sys/bus/pci/drivers/ehci-pci/unbind
echo 0000:02:01.0 > /sys/bus/pci/drivers/ohci-pci/unbind
echo ee000000.usb > /sys/bus/platform/drivers/xhci-hcd/bind
Note that there will be pinctrl-related error messages if both
internal PCI and USB3.0 are enabled but they should be just ignored:
sh-pfc e6060000.pfc: pin GP_5_22 already requested by ee0d0000.pci; cannot claim for ee000000.usb
sh-pfc e6060000.pfc: pin-182 (ee000000.usb) status -22
ata1: SATA link down (SStatus 0 SControl 300)
sh-pfc e6060000.pfc: could not request pin 182 (GP_5_22) from group usb2 on device sh-pfc
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Initialise TMU device using DT when booting bockw
using DT-reference.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This describes all of the TMU hardware of the r8a7778.
Each node is disabled and may be enabled as necessary
by board DTS files.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ch0 will be used for clock events and for periodic clock events,
ch1 will be used as clock source.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The clocks property for the scifa2 device node referred to the scifa0
clock index instead of the scifa2 clock index.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SCIF and SCIFA can be plexed onto the same wires on Lager board. The
datasheet also describes the wires as SCIFA. So, to make use of the
bigger FIFOs switch to SCIFA instead.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the PCI USB devices that are behind the PCI bridges, adding necessary
links to the USB PHY device.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the PCI USB devices that are behind the PCI bridges, adding necessary
links to the USB PHY device.
Based on the original work by Ben Dooks <ben.dooks@codethink.co.uk>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable USB PHY device for the Henninger board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable USB PHY device for the Koelsch board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the R8A7791 generic part of the USB PHY device node. It is up to the
board file to enable the device.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable USB PHY device for the Lager board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the R8A7790 generic part of the USB PHY device node. It is up to the
board file to enable the device.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This clock drives the INTCA irqpin controller modules.
Before, it was assumed enabled by the bootloader or reset state.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: devicetree@vger.kernel.org
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Specify the DU output topology, enable the DU device and configure the
related pins.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Specify the DU output topology, enable the DU device and configure the
related pins.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Specify the DU output topology, enable the DU device and configure the
related pins.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Apparently some versions of nolo don't mux the all the necessary GPMC
pins for the smc91x probe to work properly. Let's fix this issue
by adding mux support for GPMC to the kernel.
Note that GPMC clk needs input enabled for OnenNAND to work.
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With SDHCI for BG2, we can now enable the port and allow to access
Samsung M8G2FA 8GB eMMC on Sony NSZ-GS7.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
With SDHCI for BG2CD, we can now enable the port and allow to access
AzureWave WiFi/BT module on Google Chromecast.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Marvell Berlin BG2 has three, BG2CD just one pxav3 compatible
sdhci controllers, add them to the corresponding DT SoC
includes.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Marvell Berlin BG2 based Sony NSZ-GS7 has one ethernet controller
connected to rear RJ45 jack. Enable it by default.
Tested-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Internal FastEthernet PHY on BG2Q is connected via MII, add a
corresponding phy-connection-type property to the Ethernet node.
Tested-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Marvell BG2CD has two fast ethernet controllers with internal PHY,
add the corresponding nodes to SoC dtsi.
Tested-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Marvell BG2 has two fast ethernet controllers with internal PHY,
add the corresponding nodes to SoC dtsi.
Tested-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
With GPIO support for Marvell Berlin, now add the two gpio-connected
LEDs on Google Chromecast.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Enable timer 1 to be the source for the sched_clock, allowing to have a
more precise value than 1/HZ.
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The chip controller node now also describes the Marvell Berlin reset
controller. Add the required 'reset-cells' property.
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The BG2Q has an AHCI SATA controller with an eSATA interface. Enable it.
Only enable the first port, the BG2Q DMP does not support the second one.
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The BG2Q has an AHCI SATA controller. Add the corresponding nodes
(AHCI, PHY) into its device tree.
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The i2c-nomadik driver handle these devices properly from a runtime PM
perspective. Therefore, let's add them into VAPE PM domain for ux500.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The spi-pl022 driver handle these devices properly from a runtime PM
perspective. Therefore, let's add them into VAPE PM domain for ux500.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mmci driver handle these devices properly from a runtime PM
perspective, including register context save/restore. Therefore let's
add them into VAPE PM domain for ux500.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a DT node for the ux500 PM domains. Follow the DT semantics of the
generic PM domain.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Roman Byshko <rbyshko@gmail.com>
During the GPL to GPL/X11 licensing migration, the GPL notice introduced
mentionned the device trees as a library, which is not really accurate. It
began to spread by copy and paste. Fix all these library mentions to reflect
the file that it's actually just a file.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
