Add the missing definitions for BCM6345.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4091/
Signed-off-by: John Crispin <blogic@openwrt.org>
If the controller has no PCIe module attached, accessing of the device
configuration space causes a data bus error. Avoid this by checking the
status of the PCIe link in advance, and indicate an error if the link
is down.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4293/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Lantiq socs have a General Purpose Timer Unit (GPTU). This driver allows us to
initialize the timers. The voice firmware needs these timers as a reference.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4236/
The xrx200 SoC family has the same PCI clock register layout as the AR9.
Enable the same quirk as for AR9
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4235/
As a result of a non populated ->bits field inside the clock struct, the clock
domains were never powered on the Falcon. Until now we only used domains that
were also used and powered by the bootloader.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4234/
Register nmi and ejtag bootrom vectors for FALC-ON SoC.
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4238/
Support for the external interrupt unit was broken when the code was converted
to devicetree support.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4231/
The SVIP SoC has its timer IRQ on a different IRQ than 7. Fix up the irq
code to be able to handle this.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4229/
Up to now all our SoCs had the 5 IM ranges in a consecutive order. To accomodate
the SVIP we need to support IM ranges that are scattered inside the register range.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4237/
Needed by SPI driver.
Signed-off-by: David Daney <david.daney@cavium.com>
Patchwork: http://patchwork.linux-mips.org/patch/3796/
Signed-off-by: John Crispin <blogic@openwrt.org>
VSMP kernel build for non-malta platforms fails with following error
LD init/built-in.o
LD .tmp_vmlinux1
arch/mips/built-in.o: In function `vsmp_init_secondary':
smp-mt.c:(.cpuinit.text+0x23cc): undefined reference to `gic_present'
smp-mt.c:(.cpuinit.text+0x23d0): undefined reference to `gic_present'
make: *** [.tmp_vmlinux1] Error 1
gic_present variable is declared only if IRQ_GIC is selected.
Signed-off-by: Anoop P A <anoop.pa@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/2039/
Signed-off-by: John Crispin <blogic@openwrt.org>
R4K-style CPUs having common code to support their caches and tlb have this
boolean defined by default. Allows us to remove some lines in
arch/mips/mm/Makefile.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/3328/
Signed-off-by: John Crispin <blogic@openwrt.org>
R4K-style CPUs have this boolean defined by default. Allows us
to remove some lines in arch/mips/kernel/Makefile.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/3330/
Signed-off-by: John Crispin <blogic@openwrt.org>
Allows us not to duplicate more lines in arch/mips/lib/Makefile.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/3329/
Signed-off-by: John Crispin <blogic@openwrt.org>
Enable more devices and options for XLP default configuration:
- Serial ports from FDT
- NOR Flash support and partitions from FDT
- PCI and PCI bus support and devices - SATA, e1000e, sky2
- I2C ocores controller and devices - ds1374, lm90
- Misc options such as RTC, partition formats etc.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Provide a config option to embed a device tree for XLP evaluation
boards. This DTB will be used if the firmware does not pass in a
device tree pointer.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Patchwork: http://patchwork.linux-mips.org/patch/4103/
Signed-off-by: John Crispin <blogic@openwrt.org>
Add the serial ports to the device tree and remove the platform
code for adding them.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Patchwork: http://patchwork.linux-mips.org/patch/4098/
Signed-off-by: John Crispin <blogic@openwrt.org>
Add a basic DTS file netlogic/dts/nlm_xlp.dts which contains
memory, i2c devices, NOR flash and command line arguments.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Patchwork: http://patchwork.linux-mips.org/patch/4100/
Signed-off-by: John Crispin <blogic@openwrt.org>
Move the function device_tree_init() from netlogic/xlp/of.c
to setup.c, and remove the wrapper functions reserve_mem_mach()
and free_mem_mach().
Remove file netlogic/xlp/of.c, and the Makefile entry for it.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Patchwork: http://patchwork.linux-mips.org/patch/4097/
Signed-off-by: John Crispin <blogic@openwrt.org>
Previously we relied on the bootloader to have enabled this bit. However some
bootloaders seem to not enable this for us.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4120/
2ec8663f9c03a96f2c328c7c483603c31d62ad37 (lmo) rsp.
497e5ff03f (kernel.org) [MIPS: Malta: Move
PIIX4 PCI fixup to where it belongs.] attempted to move this PCI fixup
but really only added it at it's new location without deleting the old
instance.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The ath79 platform code allows to run a single kernel image on various
SoCs which are based on the 24Kc and 74Kc cores. The current code
explicitely disables the DSP ASE, but that is available in the 74Kc core.
Remove the override in order to let the kernel to detect the availability
of the DSP ASE at runtime.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4222/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current implementation of synchronise_count_{master,slave} blocks
slave CPUs in early boot until all of them come up. This no longer
works because blocking a CPU with interrupts off after notifying the
CPU to be online causes problems with the current kernel.
Specifically, after the workqueue changes
(commit a08489c569 "Pull workqueue changes from Tejun Heo")
the CPU_ONLINE notification callback workqueue_cpu_up_callback()
will hang on wait_for_completion(&idle_rebind.done), if the slave
CPUs are blocked for synchronize_count_slave().
The changes are to update synchronize_count_{master,slave}() to handle
one CPU at a time and to call synchronise_count_master() in __cpu_up()
so that the CPU_ONLINE notification goes out only after the COP0 COUNT
register is synchronized.
[ralf@linux-mips.org: This matter only to those few platforms which are
using the cp0 counter as their clocksource which are XLP, XLR and MIPS'
CMP solution.]
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4216/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
BCM6338 and BCM6348 have a message control register width of 8 bits, instead
of 16-bits like what the SPI driver assumes right now. Also the SPI message
type shift value of 14 is actually 6 for these SoCs.
This resulted in transmit FIFO corruption because we were writing 16-bits
to an 8-bits wide register, thus spanning on the first byte of the transmit
FIFO, which had already been filed in bcm63xx_spi_fill_txrx_fifo().
Fix this by passing the message control register width and message type
shift through platform data back to the SPI driver so that it can use
it properly.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: grant.likely@secretlab.ca
Cc: spi-devel-general@lists.sourceforge.net
Cc: jonas.gorski@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/3983/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In case a series of R_MIPS_HI16 relocations was not followed by an
R_MIPS_LO16 relocation we were leaking the hi16 relocation chain.
Handle that error and return an error.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The relocation code was essentially taken from the 2.4 modutils which
perform relocation in userspace. In 2.6 relocation of multiple modules
may be performed in parallel by the in-kernel loader so the global
variable mips_hi16_list won't fly anymore. Fix race by moving it into
mod_arch_specific.
[ralf@linux-mips.org: folded in Tony's followup fix. Thanks Tony!]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Tony Wu <tung7970@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/4189/
Commit 6f5d2e970452b5c86906adcb8e7ad246f535ba39 (lmo) /
477c4b0740 (kernel.org) [[MIPS: VPE: Free
relocation chain on error.] fixed the same issue in the vpe loader in 2009
but back then the same bug in module.c went unfixed.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Akhilesh Kumar <akhilesh.lxr@gmail.com>
Without this udelay(1) PCI idsel does not work correctly on the
"singleboard" (T-Mobile Surfbox) for the MiniPCI device. The result is
that PCI configuration fails and the MiniPCI card is not detected
correctly. Instead of
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fffffff]
pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
pci 0000:00:03.0: BAR 0: assigned [mem 0x40000000-0x4000ffff]
pci 0000:00:00.0: BAR 0: assigned [mem 0x40010000-0x40010fff]
pci 0000:00:00.1: BAR 0: assigned [mem 0x40011000-0x40011fff]
We see only the CardBus device:
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fffffff]
pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
pci 0000:00:00.0: BAR 0: assigned [mem 0x40000000-0x40000fff]
pci 0000:00:00.1: BAR 0: assigned [mem 0x40001000-0x40001fff]
Later the device driver shows this error:
ath5k 0000:00:03.0: cannot remap PCI memory region
ath5k: probe of 0000:00:03.0 failed with error -5
I assume that the logic chip which usually supresses the signal to the CardBus
card has some settling time and without the delay it would still let the
Cardbus interfere with the response from the MiniPCI card.
What I cannot explain is why this behaviour shows up now and not in earlier
kernel versions before. Maybe older PCI code was slower?
Signed-off-by: Bruno Randolf <br1@einfach.org>
Cc: linux-mips@linux-mips.org
Cc: manuel.lauss@googlemail.com
Cc: florian@openwrt.org
Patchwork: https://patchwork.linux-mips.org/patch/4087/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It is needed in order to get rid of the following errors:
arch/mips/ath79/clock.c:353:13: error: redefinition of 'clk_get'
include/linux/clk.h:281:27: note: previous definition of 'clk_get' was here
arch/mips/ath79/clock.c:377:5: error: redefinition of 'clk_enable'
include/linux/clk.h:295:19: note: previous definition of 'clk_enable' was here
arch/mips/ath79/clock.c:383:6: error: redefinition of 'clk_disable'
include/linux/clk.h:300:20: note: previous definition of 'clk_disable' was here
arch/mips/ath79/clock.c:388:15: error: redefinition of 'clk_get_rate'
include/linux/clk.h:302:29: note: previous definition of 'clk_get_rate' was here
arch/mips/ath79/clock.c:394:6: error: redefinition of 'clk_put'
include/linux/clk.h:291:20: note: previous definition of 'clk_put' was here
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4170/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The currently assigned IRQ number to the OHCI controller is incorrect for
the AR7240 SoC, and that leads to the following error message from the
OHCI driver:
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ath79-ohci ath79-ohci: Atheros built-in OHCI controller
ath79-ohci ath79-ohci: new USB bus registered, assigned bus number 1
ath79-ohci ath79-ohci: irq 14, io mem 0x1b000000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usb 1-1: new full-speed USB device number 2 using ath79-ohci
ath79-ohci ath79-ohci: Unlink after no-IRQ? Controller is probably using the wrong IRQ.
Fix this by using the correct IRQ number.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4168/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since 3.6.0-rc1, We are getting many messages like:
WARNING: at kernel/irq/irqdomain.c:444 irq_domain_associate_many+0x23c/0x260()
Modules linked in:
Call Trace:
[<ffffffff814cb698>] dump_stack+0x8/0x34
[<ffffffff81133d00>] warn_slowpath_common+0x78/0xa8
[<ffffffff81187e44>] irq_domain_associate_many+0x23c/0x260
[<ffffffff81187f38>] irq_create_mapping+0xd0/0x220
[<ffffffff81188104>] irq_create_of_mapping+0x7c/0x158
[<ffffffff813e5f08>] irq_of_parse_and_map+0x28/0x40
.
.
.
Both the CIU and GPIO interrupt domains were somewhat screwed up.
For the CIU domain, we need to call irq_domain_associate() for each of
the preassigned irq numbers. For the GPIO domain, we were applying
the register bit offset in octeon_irq_gpio_xlat, but it should be done
in octeon_irq_gpio_map instead.
Also: Reserve all 8 'core' irqs for the 'core' irq_chip so that they
don't get used by the other domains. Remove unused OCTEON_IRQ_*
symbols.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4190/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The changes in linux-next removing serial8250_register_port() cause
OCTEON to fail to compile.
Lets make OCTEON use the new serial8250_register_8250_port() instead.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull MIPS updates from Ralf Baechle:
"The lion share of this pull request are fixes for clk-related breakage
caused by other changes during this merge window. For some platforms
the fix was as simple as selecting HAVE_CLK, for others like the
Loongson 2 significant restructuring was required.
The remainder are changes required to get the Lantiq code to work
again."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Loongson 2: Sort out clock managment.
MIPS: Loongson 1: more clk support and add select HAVE_CLK
MIPS: txx9: Fix redefinition of clk_* by adding select HAVE_CLK
MIPS: BCM63xx: Fix redefinition of clk_* by adding select HAVE_CLK
MIPS: AR7: Fix redefinition of clk_* by adding select HAVE_CLK
MIPS: Lantiq: Platform specific CLK fixup
MIPS: Lantiq: Add device_tree_init function
MIPS: Lantiq: Fix interface clock and PCI control register offset
For unexplainable reasons the Loongson 2 clock API was implemented in a
module so fixing this involved shifting large amounts of code around.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fixes a redefinition of clk_*:
arch/mips/loongson1/common/clock.c:23:13: error: redefinition of 'clk_get'
include/linux/clk.h:281:27: note: previous definition of 'clk_get' was here
arch/mips/loongson1/common/clock.c:41:15: error: redefinition of 'clk_get_rate'
include/linux/clk.h:302:29: note: previous definition of 'clk_get_rate' was here
make[3]: *** [arch/mips/loongson1/common/clock.o] Error 1
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips@linux-mips.org
Reviewed-by: John Crispin <blogic@openwrt.org>
Acked-by: Kelvin Cheung <keguang.zhang@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/4143/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/txx9/generic/setup.c:87:13: error: redefinition of 'clk_get'
include/linux/clk.h:281:27: note: previous definition of 'clk_get' was here
arch/mips/txx9/generic/setup.c:97:5: error: redefinition of 'clk_enable'
include/linux/clk.h:295:19: note: previous definition of 'clk_enable' was here
arch/mips/txx9/generic/setup.c:103:6: error: redefinition of 'clk_disable'
include/linux/clk.h:300:20: note: previous definition of 'clk_disable' was here
arch/mips/txx9/generic/setup.c:108:15: error: redefinition of 'clk_get_rate'
include/linux/clk.h:302:29: note: previous definition of 'clk_get_rate' was here
arch/mips/txx9/generic/setup.c:114:6: error: redefinition of 'clk_put'
include/linux/clk.h:291:20: note: previous definition of 'clk_put' was here
make[3]: *** [arch/mips/txx9/generic/setup.o] Error 1
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips@linux-mips.org
Reviewed-by: John Crispin <blogic@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/4142/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/bcm63xx/clk.c:249:5: error: redefinition of 'clk_enable'
include/linux/clk.h:295:19: note: previous definition of 'clk_enable' was here
arch/mips/bcm63xx/clk.c:259:6: error: redefinition of 'clk_disable'
include/linux/clk.h:300:20: note: previous definition of 'clk_disable' was here
arch/mips/bcm63xx/clk.c:268:15: error: redefinition of 'clk_get_rate'
include/linux/clk.h:302:29: note: previous definition of 'clk_get_rate' was here
arch/mips/bcm63xx/clk.c:275:13: error: redefinition of 'clk_get'
include/linux/clk.h:281:27: note: previous definition of 'clk_get' was here
arch/mips/bcm63xx/clk.c:302:6: error: redefinition of 'clk_put'
include/linux/clk.h:291:20: note: previous definition of 'clk_put' was here
make[2]: *** [arch/mips/bcm63xx/clk.o] Error 1
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips@linux-mips.org
Reviewed-by: John Crispin <blogic@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/4141/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/ar7/clock.c:420:5: error: redefinition of 'clk_enable'
include/linux/clk.h:295:19: note: previous definition of 'clk_enable' was here
arch/mips/ar7/clock.c:426:6: error: redefinition of 'clk_disable'
include/linux/clk.h:300:20: note: previous definition of 'clk_disable' was here
arch/mips/ar7/clock.c:431:15: error: redefinition of 'clk_get_rate'
include/linux/clk.h:302:29: note: previous definition of 'clk_get_rate' was here
arch/mips/ar7/clock.c:437:13: error: redefinition of 'clk_get'
include/linux/clk.h:281:27: note: previous definition of 'clk_get' was here
arch/mips/ar7/clock.c:454:6: error: redefinition of 'clk_put'
include/linux/clk.h:291:20: note: previous definition of 'clk_put' was here
make[2]: *** [arch/mips/ar7/clock.o] Error 1
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips@linux-mips.org
Reviewed-by: John Crispin <blogic@openwrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/4140/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As we use CLKDEV_LOOKUP but dont have support for COMMON_CLK yet, we need to
provide our own version of of_clk_get_from_provider().
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4117/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a lantiq specific version of device_tree_init. The generic MIPS version
was removed by.
commit 594e966bc412d64eec9282d28ce511bdd62fea39
Author: David Daney <david.daney@cavium.com>
Date: Thu Jul 5 18:12:38 2012 +0200
MIPS: Prune some target specific code out of prom.c
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4116/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The XRX200 based SoC have a different register offset for the interface
clock and PCI control registers. This patch detects the SoC and sets the
register offset at runtime. This make PCI work on the VR9 SoC.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4113/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch is preparation for the next patch which removes the zeroing of
the pg_data_t in core MM. All archs except MIPS already do this.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge Andrew's first set of patches:
"Non-MM patches:
- lots of misc bits
- tree-wide have_clk() cleanups
- quite a lot of printk tweaks. I draw your attention to "printk:
convert the format for KERN_<LEVEL> to a 2 byte pattern" which
looks a bit scary. But afaict it's solid.
- backlight updates
- lib/ feature work (notably the addition and use of memweight())
- checkpatch updates
- rtc updates
- nilfs updates
- fatfs updates (partial, still waiting for acks)
- kdump, proc, fork, IPC, sysctl, taskstats, pps, etc
- new fault-injection feature work"
* Merge emailed patches from Andrew Morton <akpm@linux-foundation.org>: (128 commits)
drivers/misc/lkdtm.c: fix missing allocation failure check
lib/scatterlist: do not re-write gfp_flags in __sg_alloc_table()
fault-injection: add tool to run command with failslab or fail_page_alloc
fault-injection: add selftests for cpu and memory hotplug
powerpc: pSeries reconfig notifier error injection module
memory: memory notifier error injection module
PM: PM notifier error injection module
cpu: rewrite cpu-notifier-error-inject module
fault-injection: notifier error injection
c/r: fcntl: add F_GETOWNER_UIDS option
resource: make sure requested range is included in the root range
include/linux/aio.h: cpp->C conversions
fs: cachefiles: add support for large files in filesystem caching
pps: return PTR_ERR on error in device_create
taskstats: check nla_reserve() return
sysctl: suppress kmemleak messages
ipc: use Kconfig options for __ARCH_WANT_[COMPAT_]IPC_PARSE_VERSION
ipc: compat: use signed size_t types for msgsnd and msgrcv
ipc: allow compat IPC version field parsing if !ARCH_WANT_OLD_COMPAT_IPC
ipc: add COMPAT_SHMLBA support
...
Rather than #define the options manually in the architecture code, add
Kconfig options for them and select them there instead. This also allows
us to select the compat IPC version parsing automatically for platforms
using the old compat IPC interface.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE and use this instead
of the multitude of #if defined() checks in atomic64_test.c
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull MIPS updates from Ralf Baechle:
"More hardware support across the field including a bunch of device
drivers. The highlight however really are further steps towards
device tree.
This has been sitting in -next for ages. All MIPS _defconfigs have
been tested to boot or where I don't have hardware available, to at
least build fine."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (77 commits)
MIPS: Loongson 1B: Add defconfig
MIPS: Loongson 1B: Add board support
MIPS: Netlogic: early console fix
MIPS: Netlogic: Fix indentation of smpboot.S
MIPS: Netlogic: remove cpu_has_dc_aliases define for XLP
MIPS: Netlogic: Remove unused pcibios_fixups
MIPS: Netlogic: Add XLP SoC devices in FDT
MIPS: Netlogic: Add IRQ mappings for more devices
MIPS: Netlogic: USB support for XLP
MIPS: Netlogic: XLP PCIe controller support.
MIPS: Netlogic: Platform changes for XLR/XLS I2C
MIPS: Netlogic: Platform NAND/NOR flash support
MIPS: Netlogic: Platform changes for XLS USB
MIPS: Netlogic: Remove NETLOGIC_ prefix
MIPS: Netlogic: SMP wakeup code update
MIPS: Netlogic: Update comments in smpboot.S
MIPS: BCM63XX: Add 96328avng reference board
MIPS: Expose PCIe drivers for MIPS
MIPS: BCM63XX: Add PCIe Support for BCM6328
MIPS: BCM63XX: Move the PCI initialization into its own function
...
Recently, glibc made a change to suppress sign-conversion warnings in
FD_SET (glibc commit ceb9e56b3d1). This uncovered an issue with the
kernel's definition of __NFDBITS if applications #include
<linux/types.h> after including <sys/select.h>. A build failure would
be seen when passing the -Werror=sign-compare and -D_FORTIFY_SOURCE=2
flags to gcc.
It was suggested that the kernel should either match the glibc
definition of __NFDBITS or remove that entirely. The current in-kernel
uses of __NFDBITS can be replaced with BITS_PER_LONG, and there are no
uses of the related __FDELT and __FDMASK defines. Given that, we'll
continue the cleanup that was started with commit 8b3d1cda4f
("posix_types: Remove fd_set macros") and drop the remaining unused
macros.
Additionally, linux/time.h has similar macros defined that expand to
nothing so we'll remove those at the same time.
Reported-by: Jeff Law <law@redhat.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
CC: <stable@vger.kernel.org>
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
[ .. and fix up whitespace as per akpm ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
