According to the legacy drivers the AUTOWAKEUP_CFG
register must be reset to 0 before loading the firmware.
Instead of during rt2800{pci,usb}_write_firmware it
must actually be done in rt2800_load_firmware() before
resetting the WPDMA_GLO_CFG and PWR_PIN_CFG registers.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of printing a warning when the PID, ACK, or WCID of
an entry don't match the TX status report, we should skip the
entry to search for the entry which actually does match
the TX status data.
This reduces the number of watchdog errors on the TX queues
for rt2800usb, and seems to improve the reliability of the
TX flow a bit.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to rt2800_wait_wpdma_ready() we can add a
function to waiting until the CSR is ready. This
centralizes some additional code into rt2800lib.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Variables containing queue ids are called qid everywhere else, hence
rename the queue field in txentry_desc to qid as well.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to the hardware documentation, the MIC failure bit is only
valid if the frame was decrypted using a valid TKIP key and is not a
fragment.
In some setups I've seen hardware-reported MIC failures on an AP that
was configured for CCMP only, so it's clear that additional checks are
necessary.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch was adapted from 06f7bc7db7
(from linus's linux-2.6 tree of kernel.org)
here's the original message:
The queue stopping/waking functionality was broken in a way that could
cause huge latencies in TX transfers and even cause the TX to stall in the
right circumstances. Correct these problems.
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In file included from drivers/net/stmmac/stmmac_ethtool.c:30:
drivers/net/stmmac/stmmac.h:111: warning: 'struct platform_device' declared inside parameter list
drivers/net/stmmac/stmmac.h:111: warning: its scope is only this definition or declaration, which is probably not what you want
drivers/net/stmmac/stmmac_main.c: In function 'stmmac_dvr_probe':
drivers/net/stmmac/stmmac_main.c:1744: warning: cast from pointer to integer of different size
In file included from drivers/net/stmmac/stmmac_mdio.c:31:
drivers/net/stmmac/stmmac.h:111: warning: 'struct platform_device' declared inside parameter list
drivers/net/stmmac/stmmac.h:111: warning: its scope is only this definition or declaration, which is probably not what you want
drivers/net/stmmac/dwmac1000_core.c: In function 'dwmac1000_dump_regs':
drivers/net/stmmac/dwmac1000_core.c:56: warning: cast from pointer to integer of different size
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
resource_size_t changed from `unsigned long' to `phys_addr_t`, which is either
`u32' or `u64'.
Print the whole resource to remove the cast and to make it future-proof.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael reported that p54* never really entered power
save mode, even tough it was enabled.
It turned out that upon a power save mode change the
firmware will set a special flag onto the last outgoing
frame tx status (which in this case is almost always the
designated PSM nullfunc frame). This flag confused the
driver; It erroneously reported transmission failures
to the stack, which then generated the next nullfunc.
and so on...
Cc: <stable@kernel.org>
Reported-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This avoids a NULL pointer dereference as reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=625889
When the WARN condition is hit in ieee80211_get_tx_rate, it will return
NULL. So, we need to check the return value and avoid dereferencing it
in that case.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: stable@kernel.org
Acked-by: Bob Copeland <me@bobcopeland.com>
pcnet_cs:
add new_id: "KENTRONICS KEP-230" 10Base-T PCMCIA card.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nic_type field is compared to athr_l2c twice.
The sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@expression@
expression E;
@@
(
* E
|| ... || E
|
* E
&& ... && E
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net/ipv4: Eliminate kstrdup memory leak
net/caif/cfrfml.c: use asm/unaligned.h
ax25: missplaced sock_put(sk)
qlge: reset the chip before freeing the buffers
l2tp: test for ethernet header in l2tp_eth_dev_recv()
tcp: select(writefds) don't hang up when a peer close connection
tcp: fix three tcp sysctls tuning
tcp: Combat per-cpu skew in orphan tests.
pxa168_eth: silence gcc warnings
pxa168_eth: update call to phy_mii_ioctl()
pxa168_eth: fix error handling in prope
pxa168_eth: remove unneeded null check
phylib: Fix race between returning phydev and calling adjust_link
caif-driver: add HAS_DMA dependency
3c59x: Fix deadlock between boomerang_interrupt and boomerang_start_tx
qlcnic: fix poll implementation
netxen: fix poll implementation
bridge: netfilter: fix a memory leak
Detect size mismatch for netdrv_addr_t at build time rather than
checking at module load time.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Ion Badulescu <ionut@badula.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Ion Badulescu <ionut@badula.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace loops calling set_bit() and clear_bit() with bitmap_set() and
bitmap_clear().
Unlike loops calling set_bit() and clear_bit(), bitmap_set() and
bitmap_clear() are not atomic. But this is ok.
Because the bitmap operations are protected by bitmap->lock
except for initialization of the bitmap in mlx4_bitmap_init().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: netdev@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use net_device->stats for stats instead of private variable copies in
struct slip. Use ndo_get_stat64 so the additions can be performed on a private
destination buffer.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the trivial support for runtime interface
type changes to mac80211_hwsim for testing.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While scanning, ANI is triggered unnecessarily where sta is in
unassociated state. And cancelling ani work in ath9k_htc_stop
is not required.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the scan callback now being callable from
any context, these unlocks/locks can go away.
This makes the code easier to understand, since
callers of these functions must no longer be
aware that the mutex may be dropped.
As Stanislaw is working on iwlwifi scanning, I
didn't change it to take advantage of the new
mac80211 semantics.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All major Atheros customers require the led to be in continuous
ON state rather than the blinking pattern.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the symbol offset is 46, it will be counted in both
the third and fourth bytes of the mask, and in this
case the shift will be negative which can pollute
high order bits in the mask. This may negatively impact
OFDM symbol detection.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a small misordering here. In the original code, if we were to
go to err_free_ah then it wouldn't free the irq.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit 886275ce41 (param: lock
if_sdio's lbs_helper_name and lbs_fw_name against sysfs changes)
introduced new fields into the if_sdio_card structure. It caused
missalignment of the if_sdio_card.buffer field and failure at driver
load time:
~# modprobe libertas_sdio
[ 62.315124] libertas_sdio: Libertas SDIO driver
[ 62.319976] libertas_sdio: Copyright Pierre Ossman
[ 63.020629] DMA misaligned error with device 48
[ 63.025207] mmci-omap-hs mmci-omap-hs.1: unexpected dma status 800
[ 66.005035] libertas: command 0x0003 timed out
[ 66.009826] libertas: Timeout submitting command 0x0003
[ 66.016296] libertas: PREP_CMD: command 0x0003 failed: -110
Adding explicit alignment attribute for the if_sdio_card.buffer field
fixes this problem.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We're now ready to start using multiple contexts.
We do this by keeping track of the valid interface
types per context (exclusive [ibss] and normal)
and checking which context is "free" when a new
interface is added.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
It is necessary that the PAN context always
use the same beacon interval as the BSS
context unless it is in dual-station mode,
ie. the PAN context is a station as well,
so implement that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The PAN context requires also getting
RXON timing when we send an unassociated
RXON in some cases.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Sometimes we need to send RXON timing even
when we don't have a virtual interface yet,
so pass the context and allow passing one
without a virtual interface pointer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
In order for the microcode to be able to handle
multiple interfaces, we need to give it the PAN
parameters that state how to allocate the time
between the two interfaces. Do this, and update
it wherever necessary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Newer AGN microcode requires know the beacon
before starting the AP so that it can start
beaconing right away. Implement that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The PAN functionality requires us to send the
timing including a valid DTIM period to the
microcode before associating, so request this
data from mac80211 and send it to the device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Frames for different contexts need to be put
on different queues, and multicast after DTIM
frames have a special queue yet which also
depends on the context, so put all this into
the context.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since we have the beacon context now, we no
longer need to rely on iw_mode but can check
the beacon context interface's type. However,
that check must be in the work item instead
due to locking constraints (mutex must be
held when dereferencing beacon_ctx pointer).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Detect whether or not the ucode is PAN
capable and adjust the valid contexts
accordingly. To be able to do this, add
the PAN context to the array as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Define the new host commands and notifications
REPLY_WIPAN_PARAMS
REPLY_WIPAN_RXON
REPLY_WIPAN_RXON_TIMING
REPLY_WIPAN_RXON_ASSOC
REPLY_WIPAN_QOS_PARAM
REPLY_WIPAN_WEPKEY
REPLY_WIPAN_P2P_CHANNEL_SWITCH
REPLY_WIPAN_NOA_NOTIFICATION
and their corresponding structures along with the PAN
station flag, the PAN AP sta ID and new dev types for
the second context.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Only one context can be beaconing at a time,
but we need to track which one. Introduce a
new variable priv->beacon_ctx to do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
A lot of HT configuration semantically belongs into
the context, even if right now it will never be
different between contexts. Move it so we're better
prepared for future changes in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Sometimes we only pass around station
pointers but need to find the context
they belong to, so store it in there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since the default context is initialised to zero,
and the default flags are zero, no more code is
needed to initialise them right now, but another
context can have different default flags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
HW crypto needs to be aware of the context, and there
are different command IDs for the WEP keys per context,
so move the key tracking variables and command IDs into
the context structure.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Each context needs to use a different AP sta
ID, so we need to move that into the context
struct instead of hardcoding it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The dwell time should at least fit into all
context's beacon intervals.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwlwifi occasionally needs to find the virtual
interface pointer to give it to mac80211, but right
now it only keeps one. Move it into the context so
that we can keep one pointer each.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
In status processing we'll need to find the context
for a given frame, so add a context pointer to the
TX info for each frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since mac80211 doesn't currently enable/disable
QoS per interface, we can't yet do it properly,
but we can already prepare for it and move the
QoS data and command ID into the context struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Some commands will have different command IDs
for different contexts, so we need to store
those IDs in the context structure and use
them instead of hardcoding the commands.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The microcode tracks stations per context, so
the driver needs to do that as well for adding,
deleting and restoring them, especially in the
implicit removal case when we send an RXON.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
