Exynos drm hdmi driver used to get dummy hdmiphy clock to
control the PMU bit for hdmiphy. This bit needs to be set
before setting any resolution to hdmi hardware. This was
handled using dummy hdmiphy clock which is removed here.
PMU is already defined as system controller for exynos
SoCs. Hdmi driver is modified to control the phy enable bit
inside PMU using regmap interfaces.
Devicetree binding document for hdmi is also updated.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Enable support for hdmi for exynos5420 hdmiphy. Add
compatible string in the of_match table. Also added
hdmiphy configuration values for exynos5420.
Signed-off-by: Rahul Sharma <Rahul.Sharma@samsung.com>
Signed-off-by: Shirish S <s.shirish@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Certain bridge chips use a GPIO to indicate the cable status instead
of the I_DP_HPD pin. This adds an optional device-tree property,
"samsung,hpd-gpio", to the exynos-dp controller which indicates that
the specified GPIO should be used for hotplug detection.
The GPIO is then set up as an edge-triggered interrupt where the
rising edge indicates hotplug-in and the falling edge indicates hotplug-out.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
A small mistake slipped through in memory.txt.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The following warning message is triggered:
WARNING: CPU: 0 PID: 0 at mm/early_ioremap.c:136 __early_ioremap+0x11f/0x1f2()
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 3.15.0-rc1-00017-g86dfc6f3-dirty #298
Hardware name: Intel Corporation S2600CP/S2600CP, BIOS SE5C600.86B.99.99.x036.091920111209 09/19/2011
0000000000000009 ffffffff81b75c40 ffffffff817c627b 0000000000000000
ffffffff81b75c78 ffffffff81067b5d 000000000000007b 8000000000000563
00000000b96b20dc 0000000000000001 ffffffffff300e0c ffffffff81b75c88
Call Trace:
[<ffffffff817c627b>] dump_stack+0x45/0x56
[<ffffffff81067b5d>] warn_slowpath_common+0x7d/0xa0
[<ffffffff81067c3a>] warn_slowpath_null+0x1a/0x20
[<ffffffff81d4b9d5>] __early_ioremap+0x11f/0x1f2
[<ffffffff81d4bc5b>] early_ioremap+0x13/0x15
[<ffffffff81d2b8f3>] __acpi_map_table+0x13/0x18
[<ffffffff817b8d1a>] acpi_os_map_memory+0x26/0x14e
[<ffffffff813ff018>] acpi_tb_acquire_table+0x42/0x70
[<ffffffff813ff086>] acpi_tb_validate_table+0x27/0x37
[<ffffffff813ff0e5>] acpi_tb_verify_table+0x22/0xd8
[<ffffffff813ff6a8>] acpi_tb_install_non_fixed_table+0x60/0x1c9
[<ffffffff81d61024>] acpi_tb_parse_root_table+0x218/0x26a
[<ffffffff81d1b120>] ? early_idt_handlers+0x120/0x120
[<ffffffff81d610cd>] acpi_initialize_tables+0x57/0x59
[<ffffffff81d5f25d>] acpi_table_init+0x1b/0x99
[<ffffffff81d2bca0>] acpi_boot_table_init+0x1e/0x85
[<ffffffff81d23043>] setup_arch+0x99d/0xcc6
[<ffffffff81d1b120>] ? early_idt_handlers+0x120/0x120
[<ffffffff81d1bbbe>] start_kernel+0x8b/0x415
[<ffffffff81d1b120>] ? early_idt_handlers+0x120/0x120
[<ffffffff81d1b5ee>] x86_64_start_reservations+0x2a/0x2c
[<ffffffff81d1b72e>] x86_64_start_kernel+0x13e/0x14d
---[ end trace 11ae599a1898f4e7 ]---
when installing the following table during early stage:
ACPI: SSDT 0x00000000B9638018 07A0C4 (v02 INTEL S2600CP 00004000 INTL 20100331)
The regression is caused by the size limitation of the x86 early IO mapping.
The root cause is:
1. ACPICA doesn't split IO memory mapping and table mapping;
2. Linux x86 OSL implements acpi_os_map_memory() using a size limited fix-map
mechanism during early boot stage, which is more suitable for only IO
mappings.
This patch fixes this issue by utilizing acpi_gbl_verify_table_checksum to
disable the table mapping during early stage and enabling it again for the
late stage. In this way, the normal code path is not affected. Then after
the code related to the root cause is cleaned up, the early checksum
verification can be easily re-enabled.
A new boot parameter - acpi_force_table_verification is introduced for
the platforms that require the checksum verification to stop loading bad
tables.
This fix also covers the checksum verification for the table overrides. Now
large tables can also be overridden using the initrd override mechanism.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reported-and-tested-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
John W. Linville says:
====================
Please pull this batch of updates intended for 3.16...
For the mac80211 bits, Johannes says:
"Here I just have Heikki's rfkill GPIO cleanups.
The ARM/tegra patch is OK with the maintainer (Stephen). Let me know of
any problems."
and;
"We have a whole bunch of work on CSA by Andrei, Luca and Michal, but
unfortunately it doesn't seem quite complete yet so it's still disabled.
There's some TDLS work from Arik, and the rest is mostly minor fixes and
cleanups."
For the NFC bits, Samuel says:
"This is the NFC pull request for 3.16. We have:
- STMicroeectronics st21nfca support. The st21nfca is an HCI chipset and
thus relies on the HCI stack. This submission provides support for tag
redaer/writer mode (including Type 5) and device tree bindings.
- PM runtime support and a bunch of bug fixes for TI's trf7970a.
- Device tree support for NXP's pn544. Legacy platform data support is
obviously kept intact.
- NFC Tag type 4B support to the NFC Digital stack.
- SOCK_RAW type support to the raw NFC socket, and allow NCI
sniffing from that. This can be extended to report HCI frames and also
proprietarry ones like e.g. the pn533 ones."
For the iwlwifi bits, Emmanuel says:
"Eran continues to work on new devices, Eyal is still digging in
the rate control stuff, and Johannes added new functionality to the
debug system we have in place now along with a few cleanups he made
on the way. That's pretty much it."
and;
"Avri continues to work on the power code and Eran is improving the
NVM handling as a preparations for new devices on which he works
with Liad. Luca cleans up a bit the code while working on CSA. I have
the regular BT Coex stuff and a small lockdep fix. Johannes has his
regular amount of clean ups and improvements, the main one is the
ability to leave 2 chains open to improve diversity and hence the
throughput in high attenuation scenarios."
and;
"The regular amount of housekeeping here. I merged iwlwifi-fixes.git to
be able to add the patch you didn't want in wireless.git at that stage
of the -rc cycle. Luca has a few preparations for CSA implementation
and also what seems to be a bugfix for P2P but hasn't caused issues
we could notice."
For the Atheros bits, Kalle says:
"For ath10k Michal did various small fixes on how we handle
hardware/firmware problems and he also fixed two memory leaks."
Also included are a couple of pulls from the wireless tree to
avoid/resolve merge issues...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm not sure why a client would want to stuff multiple reads in a
single compound rpc, but it's legal for them to do it, and we should
really support it.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
because dm-cache cannot yet handle discards that span cache blocks.
Really fix a dm-mpath LOCKDEP warning that was introduced in -rc1.
Add a 'no_space_timeout' control to dm-thinp to restore the ability to
queue IO indefinitely when no data space is available. This fixes a
change in behavior that was introduced in -rc6 where the timeout
couldn't be disabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTh9QAAAoJEMUj8QotnQNaNpYH/j07FeH8YlxXRcFzDi7xRVtx
luK5b9fLLlmPwW2eKSrvpI8Le4jwDvLwBmpEvN9/wyPiRDSUnYIyYdoV7RJXX2LT
wqXatObb84fwQBJ6/q8o2YMzU5ODa5XT6KGEZyD4cHdAZ9FZSwfgqhslyrBJDkSN
JBFfkXu066qw8cuYA6KFv4DwBf5eHAt5AjV/QPGd5zGXwETHLZ4ypgpwYHAGbdXa
MgfHetwtEnJYvVQex/e+9xC5IDc4/BEAhZq4n3YmEJjNq8EbX15udHmCX7S2M5pT
+9tNjUMz4j9BhoC9F8ntRz0pxWZtJK9hGojO4xoXqOCOHgp1xLQd/tHrFZS0v8E=
=u5Xd
-----END PGP SIGNATURE-----
Merge tag 'dm-3.15-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device-mapper fixes from Mike Snitzer:
"A dm-cache stable fix to split discards on cache block boundaries
because dm-cache cannot yet handle discards that span cache blocks.
Really fix a dm-mpath LOCKDEP warning that was introduced in -rc1.
Add a 'no_space_timeout' control to dm-thinp to restore the ability to
queue IO indefinitely when no data space is available. This fixes a
change in behavior that was introduced in -rc6 where the timeout
couldn't be disabled"
* tag 'dm-3.15-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm mpath: really fix lockdep warning
dm cache: always split discards on cache block boundaries
dm thin: add 'no_space_timeout' dm-thin-pool module param
Add support for a generic PCI host controller, such as a
firmware-initialised device with static windows or an emulation by
something such as kvmtool.
The controller itself has no configuration registers and has its address
spaces described entirely by the device-tree (using the bindings from
ePAPR). Both CAM and ECAM are supported for Config Space accesses.
Add corresponding documentation for the DT binding.
[bhelgaas: currently uses the ARM-specific pci_common_init_dev() interface]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
This patch add pmusysreg node for Exynos3250 to access PMU
(Power Management Unit) register in a centralized way using
syscon driver.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The EXYNOS5410 clocks are statically listed and registered
using the Samsung specific common clock helper functions.
Signed-off-by: Tarek Dakhran <t.dakhran@samsung.com>
Signed-off-by: Vyacheslav Tyrtov <v.tyrtov@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In this round we have a few nice gems. PR KVM gains initial POWER8 support
as well as LE host awareness, ihe e500 targets can now properly run u-boot,
LE guests now work with PR KVM including KVM hypercalls and HV KVM guests
can now use huge pages.
On top of this there are some bug fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=t4YN
-----END PGP SIGNATURE-----
Merge tag 'signed-kvm-ppc-next' of git://github.com/agraf/linux-2.6 into kvm-next
Patch queue for ppc - 2014-05-30
In this round we have a few nice gems. PR KVM gains initial POWER8 support
as well as LE host awareness, ihe e500 targets can now properly run u-boot,
LE guests now work with PR KVM including KVM hypercalls and HV KVM guests
can now use huge pages.
On top of this there are some bug fixes.
Conflicts:
include/uapi/linux/kvm.h
Commit b005255e12 ("KVM: PPC: Book3S HV: Context-switch new POWER8
SPRs") added a definition of KVM_REG_PPC_WORT with the same register
number as the existing KVM_REG_PPC_VRSAVE (though in fact the
definitions are not identical because of the different register sizes.)
For clarity, this moves KVM_REG_PPC_WORT to the next unused number,
and also adds it to api.txt.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Commit 3b7834743f ("KVM: PPC: Book3S HV: Reserve POWER8 space in get/set_one_reg") added definitions for several KVM_REG_PPC_* symbols
but missed adding some to api.txt. This adds them.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Old guests try to use the magic page, but map their trampoline code inside
of an NX region.
Since we can't fix those old kernels, try to detect whether the guest is sane
or not. If not, just disable NX functionality in KVM so that old guests at
least work at all. For newer guests, add a bit that we can set to keep NX
functionality available.
Signed-off-by: Alexander Graf <agraf@suse.de>
- From Daniel Lezcano:
This patchset relies on the cpm_pm notifier to initiate the
powerdown sequence operations from pm.c instead cpuidle.c.
Thus the cpuidle driver is no longer dependent from arch
specific code as everything is called from the pm.c file.
Note, this is based on tags/exnos-mcpm and tags/samsung-clk
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=RacH
-----END PGP SIGNATURE-----
Merge tag 'exynos-cpuidle' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/drivers
Merge "Samsung exynos-cpuidle updates for v3.16" from Kukjin Kim:
- From Daniel Lezcano:
This patchset relies on the cpm_pm notifier to initiate the
powerdown sequence operations from pm.c instead cpuidle.c.
Thus the cpuidle driver is no longer dependent from arch
specific code as everything is called from the pm.c file.
* tag 'exynos-cpuidle' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (94 commits)
ARM: EXYNOS: Fix kernel panic when unplugging CPU1 on exynos
ARM: EXYNOS: Move the driver to drivers/cpuidle directory
ARM: EXYNOS: Cleanup all unneeded headers from cpuidle.c
ARM: EXYNOS: Pass the AFTR callback to the platform_data
ARM: EXYNOS: Move S5P_CHECK_SLEEP into pm.c
ARM: EXYNOS: Move the power sequence call in the cpu_pm notifier
ARM: EXYNOS: Move the AFTR state function into pm.c
ARM: EXYNOS: Encapsulate the AFTR code into a function
ARM: EXYNOS: Disable cpuidle for exynos5440
ARM: EXYNOS: Encapsulate boot vector code into a function for cpuidle
ARM: EXYNOS: Pass wakeup mask parameter to function for cpuidle
ARM: EXYNOS: Remove ifdef for scu_enable in pm
ARM: EXYNOS: Move scu_enable in the cpu_pm notifier
ARM: EXYNOS: Use the cpu_pm notifier for pm
ARM: EXYNOS: Fix S5P_WAKEUP_STAT call for cpuidle
ARM: EXYNOS: Move some code inside the idle_finisher for cpuidle
ARM: EXYNOS: Encapsulate register access inside a function for pm
ARM: EXYNOS: Change function name prefix for cpuidle
ARM: EXYNOS: Use cpuidle_register
ARM: EXYNOS: Prevent forward declaration for cpuidle
...
Signed-off-by: Olof Johansson <olof@lixom.net>
In this time, it is having dependency with arch/arm/ for 3.16,
I pulled them into samsung tree from Tomasz under agreement from Mike.
- Pull for_3.16/exynos5260 from Tomasz Figa:
"This pull request contains patches preparing Samsung Common Clock Framework
helpers to support Exynos5260 by adding support for multiple clock providers
and then adding clock driver for Exynos5260."
- Pull for_3.16/clk_fixes_non_critical from Tomasz Figa:
"This pull requests contains a number of non-critical fixes for Samsung clock
framework and drivers, including:
1) a series of fixes for Exynos5420 to correct clock definitions and make the
driver closer to the documentation,
2) several missing clocks and clock IDs added to Exynos4, Exynos5250 and
Exynos5420 drivers,
3) fix for incorrect initialization of clock table with NULL,
4) compiler warning fix."
- Pull for_3.16/clk_cleanup from Tomasz Figa:
"This pull requests contains minor clean-up related to Samsung clock
support, including:
1) move Kconfig entries of Samsung clock drivers to drivers/clk,
2) compile drivers/clk/samsung conditionally when COMMON_CLK_SAMSUNG is
selected,
3) remove obsolete Kconfig lines after moving s3c24xx to CCF."
- Pull for_3.16/exynos3250 from Tomasz Figa:
"This small pull request contains a patch adding clock driver for Exynos3250,
which depends on previous pull requests in this series."
- add dt bindings for exynos3250 clock
- add exynos5800 specific clocks in current exynos5420 clock
Note that this branch is based on s3c24xx ccf branch
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=PqTJ
-----END PGP SIGNATURE-----
Merge tag 'samsung-clk' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
Merge "Samsung clock updates for 3.16" from Kukjin Kim:
In this time, it is having dependency with arch/arm/ for 3.16,
I pulled them into samsung tree from Tomasz under agreement from Mike.
- Pull for_3.16/exynos5260 from Tomasz Figa:
"This pull request contains patches preparing Samsung Common Clock Framework
helpers to support Exynos5260 by adding support for multiple clock providers
and then adding clock driver for Exynos5260."
- Pull for_3.16/clk_fixes_non_critical from Tomasz Figa:
"This pull requests contains a number of non-critical fixes for Samsung clock
framework and drivers, including:
1) a series of fixes for Exynos5420 to correct clock definitions and make the
driver closer to the documentation,
2) several missing clocks and clock IDs added to Exynos4, Exynos5250 and
Exynos5420 drivers,
3) fix for incorrect initialization of clock table with NULL,
4) compiler warning fix."
- Pull for_3.16/clk_cleanup from Tomasz Figa:
"This pull requests contains minor clean-up related to Samsung clock
support, including:
1) move Kconfig entries of Samsung clock drivers to drivers/clk,
2) compile drivers/clk/samsung conditionally when COMMON_CLK_SAMSUNG is
selected,
3) remove obsolete Kconfig lines after moving s3c24xx to CCF."
- Pull for_3.16/exynos3250 from Tomasz Figa:
"This small pull request contains a patch adding clock driver for Exynos3250,
which depends on previous pull requests in this series."
- add dt bindings for exynos3250 clock
- add exynos5800 specific clocks in current exynos5420 clock
Note that this branch is based on s3c24xx ccf branch
* tag 'samsung-clk' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (59 commits)
clk: exynos5420: Add 5800 specific clocks
dt-bindings: add documentation for Exynos3250 clock controller
ARM: S3C24XX: fix merge conflict
clk: samsung: exynos3250: Add clocks using common clock framework
drivers: clk: use COMMON_CLK_SAMSUNG for Samsung clock support
ARM: S3C24XX: move S3C24XX clock Kconfig options to Samsung clock Kconfig file
ARM: select COMMON_CLK_SAMSUNG for ARCH_EXYNOS and ARCH_S3C64XX
clk: samsung: add new Kconfig for Samsung common clock option
ARM: S3C24XX: Remove omitted Kconfig selects and conditionals
clk: samsung: exynos5420: add more registers to restore list
clk: samsung: exynos5420: add misc clocks
clk: samsung: exynos5420: update clocks for MAU Block
clk: samsung: exynos5420: fix register offset for sclk_bpll
clk: samsung: exynos5420: correct sysmmu-mfc parent clocks
clk: samsung: exynos5420: update clocks for FSYS and FSYS2 blocks
clk: samsung: exynos5420: update clocks for WCORE block
clk: samsung: exynos5420: update clocks for PERIS and GEN blocks
clk: samsung: exynos5420: update clocks for PERIC block
clk: samsung: exynos5420: update clocks for DISP1 block
clk: samsung: exynos5420: update clocks for G2D and G3D blocks
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- adding MCPM backend support for SMP secondary boot and core switching
on Samsung's Exynos5420.
Tested on exynos5420-smdk5420 and exynos5420 based chromebook (peach-pit)
using the "/dev/b.L_switcher" user interface. Secondary core boot-up has
also been tested on both the boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=d5ZP
-----END PGP SIGNATURE-----
Merge tag 'exynos-mcpm' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
Merge "Exynos MCPM support for v3.16" from Kukjin Kim:
- adding MCPM backend support for SMP secondary boot and core switching
on Samsung's Exynos5420.
Tested on exynos5420-smdk5420 and exynos5420 based chromebook (peach-pit)
using the "/dev/b.L_switcher" user interface. Secondary core boot-up has
also been tested on both the boards.
* tag 'exynos-mcpm' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Add MCPM call-back functions
ARM: dts: add CCI node for exynos5420
ARM: EXYNOS: Add generic cluster power control functions
ARM: EXYNOS: use generic exynos cpu power control functions
ARM: EXYNOS: Add generic cpu power control functions for exynos SoCs
Signed-off-by: Olof Johansson <olof@lixom.net>
- exynos4
: add hsotg device, exynos_usbphy nodes
: add PMU syscon and audio subsystem nodes
: replace number by macro in clock binding
- exynos4210-universal_c210
: add external sd card node and multimedia nodes
: enable USB functionality
- exynos4412-trats2
: enable usb nodes and usb gagdet functionality
: add cm36651 light/proximity sensor node
: fixed gpio key node
- exynos5250 and exynos5420
: add pmu syscon handle and sysreg system controller nodes
: add support for usb2phy
: replace number by macro in clock binding
: add USB 2.0 support on exynos5420
- exynos5420-peach-pit
: move dp hpd gpio pin to pinctrl_0
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=QihP
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-2' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung 2nd DT updates for v3.16" from Kukjin Kim:
exynos4
- add hsotg device, exynos_usbphy nodes
- add PMU syscon and audio subsystem nodes
- replace number by macro in clock binding
exynos4210-universal_c210
- add external sd card node and multimedia nodes
- enable USB functionality
exynos4412-trats2
- enable usb nodes and usb gagdet functionality
- add cm36651 light/proximity sensor node
- fixed gpio key node
exynos5250 and exynos5420
- add pmu syscon handle and sysreg system controller nodes
- add support for usb2phy
- replace number by macro in clock binding
- add USB 2.0 support on exynos5420
exynos5420-peach-pit
- move dp hpd gpio pin to pinctrl_0
* tag 'samsung-dt-2' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (21 commits)
ARM: dts: enable usb nodes for exynos4412-trats2
ARM: dts: add hsotg device node for exynos4
ARM: dts: add exynos_usbphy node for exynos4
ARM: dts: add PMU syscon node for exynos4
ARM: dts: add pmu syscon handle to exynos5420 hdmi
ARM: dts: add pmu syscon handle to exynos5250 hdmi
ARM: dts: replace number by macro in clock binding for exynos5420
ARM: dts: replace number by macro in clock binding for exynos5250
ARM: dts: replace number by macro in clock binding for exynos4
ARM: dts: add external sd card node for exynos4210-universal_c210
ARM: dts: add multimedia nodes for exynos4210-universal_c210
ARM: dts: enable USB functionality for exynos4210-universal_c210
ARM: dts: Enable USB gadget functionality for exynos4210-trats
ARM: dts: Add audio subsystem nodes to exynos4.dtsi
ARM: dts: fixed gpio key node for exynos4412-trats2
ARM: dts: add cm36651 light/proximity sensor node for exynos4412-trats2
ARM: dts: Add USB 2.0 support on exynos5420
ARM: dts: Add usb2phy support on exynos5420
ARM: dts: Add usb2phy to exynos5250
ARM: dts: Add sysreg sytem controller node to exynos5250 and exynos5420
...
A new PLL (gpll4) is added on msm8974 PRO devices to support a
faster sdc1 clock rate. Add support for this and the two new sdcc
cal clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Undo a feature introduced in v3.14 by commit fcd46b3442
"firewire: Enable remote DMA above 4 GB". That change raised the
minimum address at which protocol drivers and user programs can register
for request reception from 0x0001'0000'0000 to 0x8000'0000'0000.
It turned out that at least one vendor-specific protocol exists which
uses lower addresses: https://bugzilla.kernel.org/show_bug.cgi?id=76921
For the time being, revert most of commit fcd46b3442 so that affected
protocols work like with kernel v3.13 and before. Just keep the valid
documentation parts from the regressing commit, and the ability to
identify controllers which could be programmed to accept >32 bit
physical DMA addresses. The rest of fcd46b3442 should probably be
brought back as an optional instead of default feature.
Reported-by: Fabien Spindler <fabien.spindler@inria.fr>
Cc: <stable@vger.kernel.org> # 3.14+
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This adds DT support to the tsc2005 touchscreen driver. It also adds
regulator support to the driver if booted via DT.
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add common DT binding documentation for touchscreen devices and
implement input_parse_touchscreen_of_params, which parses the common
properties and configures the input device accordingly.
The method currently does not interpret the axis inversion properties,
since there is no matching flag in the generic linux input device.
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* pci/hotplug:
PCI: cpqphp: Fix possible null pointer dereference
NVMe: Implement PCIe reset notification callback
PCI: Notify driver before and after device reset
* pci/pci_is_bridge:
pcmcia: Use pci_is_bridge() to simplify code
PCI: pciehp: Use pci_is_bridge() to simplify code
PCI: acpiphp: Use pci_is_bridge() to simplify code
PCI: cpcihp: Use pci_is_bridge() to simplify code
PCI: shpchp: Use pci_is_bridge() to simplify code
PCI: rpaphp: Use pci_is_bridge() to simplify code
sparc/PCI: Use pci_is_bridge() to simplify code
powerpc/PCI: Use pci_is_bridge() to simplify code
ia64/PCI: Use pci_is_bridge() to simplify code
x86/PCI: Use pci_is_bridge() to simplify code
PCI: Use pci_is_bridge() to simplify code
PCI: Add new pci_is_bridge() interface
PCI: Rename pci_is_bridge() to pci_has_subordinate()
* pci/virtualization:
PCI: Introduce new device binding path using pci_dev.driver_override
Conflicts:
drivers/pci/pci-sysfs.c
* pci/host-exynos:
PCI: exynos: Remove unnecessary OOM messages
* pci/host-rcar:
PCI: rcar: Add gen2 device tree support
PCI: rcar: Add R-Car PCIe device tree bindings
PCI: rcar: Add MSI support for PCIe
PCI: rcar: Add Renesas R-Car PCIe driver
PCI: rcar: Use new OF interrupt mapping when possible
* pci/amd-numa:
x86/PCI: Clean up and mark early_root_info_init() as deprecated
x86/PCI: Work around AMD Fam15h BIOSes that fail to provide _PXM
x86/PCI: Warn if we have to "guess" host bridge node information
The driver_override field allows us to specify the driver for a device
rather than relying on the driver to provide a positive match of the
device. This shortcuts the existing process of looking up the vendor and
device ID, adding them to the driver new_id, binding the device, then
removing the ID, but it also provides a couple advantages.
First, the above existing process allows the driver to bind to any device
matching the new_id for the window where it's enabled. This is often not
desired, such as the case of trying to bind a single device to a meta
driver like pci-stub or vfio-pci. Using driver_override we can do this
deterministically using:
echo pci-stub > /sys/bus/pci/devices/0000:03:00.0/driver_override
echo 0000:03:00.0 > /sys/bus/pci/devices/0000:03:00.0/driver/unbind
echo 0000:03:00.0 > /sys/bus/pci/drivers_probe
Previously we could not invoke drivers_probe after adding a device to
new_id for a driver as we get non-deterministic behavior whether the driver
we intend or the standard driver will claim the device. Now it becomes a
deterministic process, only the driver matching driver_override will probe
the device.
To return the device to the standard driver, we simply clear the
driver_override and reprobe the device:
echo > /sys/bus/pci/devices/0000:03:00.0/driver_override
echo 0000:03:00.0 > /sys/bus/pci/devices/0000:03:00.0/driver/unbind
echo 0000:03:00.0 > /sys/bus/pci/drivers_probe
Another advantage to this approach is that we can specify a driver override
to force a specific binding or prevent any binding. For instance when an
IOMMU group is exposed to userspace through VFIO we require that all
devices within that group are owned by VFIO. However, devices can be
hot-added into an IOMMU group, in which case we want to prevent the device
from binding to any driver (override driver = "none") or perhaps have it
automatically bind to vfio-pci. With driver_override it's a simple matter
for this field to be set internally when the device is first discovered to
prevent driver matches.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The generic SPMI example was missing an equal sign in the assignment
of the #size-cells property.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit extends the compatible string list of the xhci-platform
binding with the new "renesas,xhci-r8a7790" and "renesas,xhci-r8a7791"
compatible strings. It is used to describe the xHCI controller which
is available in the R-Car H2 and M2 SoCs.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250 uart driver currently supports only software assisted hw flow
control. The software assisted hw flow control maintains a hw_stopped
flag in the tty structure to stop and start transmission and use modem
status interrupt for the event to drive the handshake signals. This is
not needed if hw has flow control capabilities. This patch adds a
DT attribute for enabling hw flow control for a uart port. Also skip
stop and start if this flag is present in flag field of the port
structure.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
CC: Rob Herring <robh+dt@kernel.org>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Kumar Gala <galak@codeaurora.org>
CC: Randy Dunlap <rdunlap@infradead.org>
CC: Jiri Slaby <jslaby@suse.cz>
CC: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On sam9x5, dedicated CTS (and RTS) pins are unusable together with the
LCDC, the EMAC, or the MMC because they share the same line.
Moreover, the USART controller doesn't handle DTR/DSR/DCD/RI signals,
so we have to control them via GPIO.
This patch permits to use GPIOs to control the CTS/RTS/DTR/DSR/DCD/RI
signals.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add some helpers to control modem lines (CTS/RTS/DSR...) via
GPIO.
This will be useful for many boards which have a serial controller that
only handle CTS/RTS pins (or even just RX/TX).
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RTS pin is an active low pin.
For now, this doesn't change anything as the ACTIVE_LOW flag is not
handled in atmel_serial, but it will be in 3.16.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simply document a new compat string.
There appears to be no need for a driver updates.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's one existing use of 'micrel' in the documentation so use
'micrel' instead of the company's ticker symbol 'mcrl'.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rob Herring <robh@kernel.org>
"7408484 usb: gadget: s3c-hsotg: enable generic phy support" introduces
generic phy support to the dwc2.txt binding and the s3c-hsotg driver
which implements support for the binding. The binding documentation
incorrectly states that the phy-names property will be "device". The
binding example, driver, and one dts user all implement the phy-names
property as requiring "usb2-phy".
Fix the dwc2.txt binding documentation to correctly specify "usb2-phy"
as the appropriate value for phy-names.
Reported-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The PPC fixes are important because they fix breakage that is new in 3.15.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=E2fU
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Small fixes for x86, slightly larger fixes for PPC, and a forgotten
s390 patch. The PPC fixes are important because they fix breakage
that is new in 3.15"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: s390: announce irqfd capability
KVM: x86: disable master clock if TSC is reset during suspend
KVM: vmx: disable APIC virtualization in nested guests
KVM guest: Make pv trampoline code executable
KVM: PPC: Book3S: ifdef on CONFIG_KVM_BOOK3S_32_HANDLER for 32bit
KVM: PPC: Book3S HV: Add missing code for transaction reclaim on guest exit
KVM: PPC: Book3S: HV: make _PAGE_NUMA take effect
Add device tree probing support to the 'pci-rcar-gen2' driver.
[Sergei: numerous fixes/cleanups/additions]
[bhelgaas: whitespace fix]
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Audio Tracking Logic is designed to be used by HD Radio applications to
synchronize the audio output clocks to the baseband clock. ATL can be also
used to track errors between two reference clocks (BWS, AWS) and generate a modulated
clock output which averages to some desired frequency.
In essence ATL is generating a clock to be used by an audio codec and also
to be used by the SoC as MCLK.
To be able to integrate the ATL provided clocks to the clock tree we need
two types of DT binding:
- DT clock nodes to represent the ATL clocks towards the CCF
- binding for the ATL IP itself which is going to handle the hw
configuration
The reason for this type of setup is that ATL itself is a separate device
in the SoC, it has it's own address space and clock domain. Other IPs can
use the ATL generated clock as their functional clock (McASPs for example)
and external components like audio codecs can also use the very same clock
as their MCLK.
The ATL IP in DRA7 contains 4 ATL instences.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
OMAP2430 I2CHS modules require specific hardware ops to be used, so added
a new compatible string for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
OMAP2 has slightly different DPLL compared to later OMAP generations.
This patch adds support for the ti,omap2-dpll-core-clock and also adds
the bindings documentation.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
