Split the core header files into manageable pieces.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* We call reset too often and this can result various PHY problems.
On config_interface we don't need to reset the whole device.
TODO: Create a function hw_fast_reset that only resets the PCU
(tx/rx stuff) and not the whole device so that we can use this for
stuck beacons etc.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Don't enable BMISS interrupts as we don't handle them yet
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update reset and sync with HALs
* Clean up eeprom settings and tweaking of initvals and
put them on separate functions
* Set/Restore 32KHz ref clk operation
* Add some more documentation
TODO: Spur mitigation, tpc, half/quarter rate, compression etc
v2: Address comments from Bob and Felix and fix RSSI threshold bug
introduced on the first version of the patch
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update initvals to match legacy and Sam's HAL
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Use the new way to modify rf buffer and put some rf buffer
documentation on rfbufer.h
* Merge all rf regs functions to one
* Sync with legacy HAL and Sam's HAL
* Set gain_F settings so that gain_F optimization engine works
on RF5111/RF5112 (note that both HALs only use step 0 for RF5111
and they don't use gain_F optimization for this chip, code is
there but is never used)
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update and cleanup rf gain optimization code
* Add comments and refferences to docs and use sane function names
* Use only step index on ath5k_gain, no need to have a pointer to
the current step since we can determine te step from it's index,
this also allows us to put all other structs on rfgain.h and cleanup
ath5k.h a little
* No need for ah_rfgain variable, we use ah_gain.g_state for everything
* Tested on RF2112B chip but gain_F calibration is not yet done
(we will finish this on the next patch where we'll rewrite rf-buffer
handling)
* Use initial rf gain settings for 2316 and 2317 SoCs introduced on a previous patch
It seems big but it's mostly cleanup, very few functional changes have been made on phy.c
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Clean up initial rf buffer settings (new file rfbufer.h) and introduce a
new way to access specific rf registers (will use it later)
* Clean up initial rf gain settings by moving them on a new file (rfgain.h)
so we can later work on gain optimization functions
* Update initial rf buffer settings and initial rf gain settings from HALs.
This breaks things for now because our current dumps come from pre-configured
rf buffer (regdumps already had the needed values set from binary HAL).
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just compile it into the orinoco module. If we merge USB support, the
module can then be split as appropriate.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... when used by the WEXT ioctl functions. This will allow us to
separate the card specific stuff from the WEXT code.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits)
wimax: fix oops in wimax_dev_get_by_genl_info() when looking up non-wimax iface
net: 4 bytes kernel memory disclosure in SO_BSDCOMPAT gsopt try #2
netxen: fix compile waring "label ‘set_32_bit_mask’ defined but not used" on IA64 platform
bnx2: Update version to 1.9.2 and copyright.
bnx2: Fix jumbo frames error handling.
bnx2: Update 5709 firmware.
bnx2: Update 5706/5708 firmware.
3c505: do not set pcb->data.raw beyond its size
Documentation/connector/cn_test.c: don't use gfp_any()
net: don't use in_atomic() in gfp_any()
IRDA: cnt is off by 1
netxen: remove pcie workaround
sun3: print when lance_open() fails
qlge: bugfix: Add missing rx buf clean index on early exit.
qlge: bugfix: Fix RX scaling values.
qlge: bugfix: Fix TSO breakage.
qlge: bugfix: Add missing dev_kfree_skb_any() call.
qlge: bugfix: Add missing put_page() call.
qlge: bugfix: Fix fatal error recovery hang.
qlge: bugfix: Use netif_receive_skb() and vlan_hwaccel_receive_skb().
...
When compile the latest kernel on IA64 platform,I got a warning:
drivers/net/netxen/netxen_nic_main.c:203: warning: label ‘set_32_bit_mask’
defined but not used
We do not need label ‘set_32_bit_mask’ on IA64 platform,So move it to #else.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If errors are reported on a frame descriptor, we need to
account for the buffer pages that may have been used for this
error packet and recycle them. Otherwise, we may get the wrong
pages for the next packet.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New firmware fixes a data corruption issue when receiving and
placing jumbo frames into host buffers. In some cases, the
buffer descriptor is not updated correctly and this will lead
to the driver linking the wrong number of pages into the SKB.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New firmware fixes a data corruption issue when receiving and
placing jumbo frames into host buffers. In some cases, the
buffer descriptor is not updated correctly and this will lead
to the driver linking the wrong number of pages into the SKB.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that we do not set pcb->data.raw beyond its size, print an error message
and return false if we attempt to. A timout message was printed one too early.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If no prior break occurs, cnt reaches 101 after the loop, so we are still able
to change speed when cnt has become 100.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove workaround for pcie bug in early revisions of NX3031
(rev 41 or earlier). This is taken care of during firmware init.
The workaround required writing pcie config reg of every
pcie function on a card, not all of which are enabled.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With while (--i > 0) { ... } i reaches 0; print when lance_open() fails
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The large receive buffer queue is not properly tracking the current
index in the case where an early exit occurs. This can happen when a
page alloc or dma mapping fails. If this occurs the queue will get
out of sync and invalid indexes can be written to the hardware.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Receive packets were only scaling across 2 of the receive queues. The
value was hardcoded to 2 instead of being based on how many rx queues
were running.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moved the buffer mapping to a point after TSO logic has modified the
iph->check field. We were seeing stale data on the PCIe bus.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We put the skb back if we can't get mapping for it. We don't
want unmapped buffers on our receive buffer queue.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We put the page back if we can't get mapping for it. We don't
want unmapped buffers on our receive buffer queue.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace calls to vlan_hwaccel_rx() and netif_rx().
Thanks to Dave Miller for pointing out the the driver was making
the wrong upcall for passing packets into the stack.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With while (limit--) { ... } limit reaches -1, so 0 means success.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove adapter from adapter list before freeing data structure in
error path.
Signed-off-by: Hannes Hering <hering2@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the interface to the scan helpers consistent, so we can split
them out.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So that we can split up the file and still produce a module named
orinoco.o.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ERROR: "foo * bar" should be "foo *bar"
ERROR: do not initialise statics to 0 or NULL
WARNING: printk() should include KERN_ facility level
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove most checkpatch warnings of the type
WARNING: line over 80 characters
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the following checkpatch warnings
WARNING: braces {} are not necessary for any arm of this statement
WARNING: braces {} are not necessary for single statement blocks
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove checkpatch warnings of the following type:
ERROR: space prohibited after that open parenthesis '('
ERROR: space prohibited before that close parenthesis ')'
ERROR: space prohibited after that '!' (ctx:BxW)
ERROR: space required before the open parenthesis '('
ERROR: space required before the open brace '{'
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the following checkpatch errors from orinoco.c
ERROR: trailing whitespace
ERROR: code indent should use tabs where possible
WARNING: suspect code indent for conditional statements
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the initial parts of the LP-PHY TX power control.
This also adds helper functions for bulk access of LP tables.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use mac80211's primitives for identifying the frame type,
and cleanup the driver-specific macros.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Here we do two things:
First, revert "iwlwifi: save PCI state before suspend, restore after
resume". That misguided patch led to being unable to use iwlwifi
devices after resume.
Next, indicate to PCI driver that the saved PCI state is valid during suspend.
We restore PCI state and enable the device when network interface is created,
similarly PCI state is saved and the device is disabled when network interface
is removed. Thus, when .suspend is called the PCI state is saved and device
is disabled. This is the case even if an interface is never created as PCI
state is saved and device disabled during .probe.
PCI driver assumes PCI state is saved in .suspend. Saving the state at this
time will save state of disabled device and thus cause problems during
resume (resuming a disabled device). We thus indicate directly to PCI
driver that current PCI saved state is valid.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Alex Riesen <fork0@users.sf.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Three people (Petr Mensik <pihhan@cipis.net>
["si" should be U+0161 U+00ED], Stephen Ho <stephenhoinhk@gmail.com>
on zd1211-devs and Ismael Ojeda Perez <iojedaperez@gmail.com>
on linux-wireless) reported success in getting TP-Link WN322G/WN422G
working by treating MAXIM_NEW_RF(0x08) as UW2453_RF(0x09) for rf
chip hardware initialization.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: Petr Mensik <pihhan@cipis.net>
Tested-by: Stephen Ho <stephenhoinhk@gmail.com>
Tested-by: Ismael Ojeda Perez <iojedaperez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
