Currently, the 9p net wire operation ensures that all data is sent by sending
multiple packets if the data requested is larger than the msize. This is
better handled in the vfs code so that we can simplify wire operations to
being concerned with only putting data onto and taking data off of the wire.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
There are a couple of methods in the client code which aren't actually
wire operations. To keep things organized cleaner, these operations are
being moved to the fs layer.
This patch moves the readn meta-function (which executes multiple wire
reads until a buffer is full) to the fs layer.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Currently there are two separate versions of read and write. One for
dealing with user buffers and the other for dealing with kernel buffers.
There is a tremendous amount of code duplication in the otherwise
identical versions of these functions. This patch adds an additional
user buffer parameter to read and write and conditionalizes handling of
the buffer on whether the kernel buffer or the user buffer is populated.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Post p9_fd_poll() error path which checks m->poll_waddr[i] for PTR_ERR
value has the following problems.
* It's completely unused. Error value is set iff NULL @wait_address
has been specified to p9_pollwait() which is guaranteed not to
happen.
* It dereferences @m after deallocating it (introduced by 571ffeaf and
spotted by Raja R Harinath.
* It returned the wrong value on error. It should return
poll_waddr[i] but it returnes poll_waddr (introduced by 571ffeaf).
* p9_mux_poll_stop() doesn't handle PTR_ERR value. It will try to
operate on the PTR_ERR value as if it's a normal pointer and cause
oops.
As the error path is bogus in the first place, there's no reason to
hold onto it. Kill it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Raja R Harinath <harinath@hurrynot.org>
This code moves the rpc function to the common client base,
reorganizes the flush code to be more simple and stable, and
makes the necessary adjustments to the underlying transports
to adapt to the new structure.
This reduces the overall amount of code duplication between the
transports and should make adding new transports more straightforward.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
This patch reworks the read_work function to enable it to directly use a passed
in rcall structure. This should help allow us to remove unnecessary copies
in the future.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
The virtio transport uses a simplified request management system
that I want to use for all transports. This patch adapts and moves the
exisiting code for managing requests to the client common code.
Later patches will apply these mechanisms to the other transports.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
The current trans_fd rpc mechanisms use a dynamic callback mechanism which
introduces a lot of complexity which only accomodates a single special case.
This patch removes much of that complexity in favor of a simple exception
mechanism to deal with flushes.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Currently, trans_fd has two structures (p9_req and p9_mux-rpc)
which contain mostly duplicate data.
This patch consolidates these two structures and removes p9_mux_rpc.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Cleanup files by reordering functions in order to remove need for
unnecessary function prototypes.
There are no code changes here, just functions being moved around and
prototypes being eliminated.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Now that we are passing client state into the transport modules, remove
duplicate state which is present in transport private structures.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Right now there is a transport module structure which provides per-transport
type functions and data and a transport structure which contains per-instance
public data as well as function pointers to instance specific functions.
This patch moves public transport visible instance data to the client
structure (which in some cases had duplicate data) and consolidates the
functions into the transport module structure.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
trans_fd used pool of upto 100 pollers to monitor the r/w fds. The
approach makes sense in userspace back when the only available
interfaces were poll(2) and select(2). As each event monitor -
trigger - handling iteration took O(n) where `n' is the number of
watched fds, it makes sense to spread them to many pollers such that
the `n' can be divided by the number of pollers. However, this
doesn't make any sense in kernel because persistent edge triggered
event monitoring is how the whole thing is implemented in the kernel
in the first place.
This patch converts trans_fd to use single poller which watches all
the fds instead of the poll of pollers approach. All the fds are
registered for monitoring on creation and only the fds with pending
events are scanned when something happens much like how epoll is
implemented.
This change makes trans_fd fd monitoring more efficient and simpler.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Remove CONFIG_KMOD from net/ (towards removing CONFIG_KMOD entirely)
ipv4: Add a missing rcu_assign_pointer() in routing cache.
[netdrvr] ibmtr: PCMCIA IBMTR is ok on 64bit
xen-netfront: Avoid unaligned accesses to IP header
lmc: copy_*_user under spinlock
[netdrvr] myri10ge, ixgbe: remove broken select INTEL_IOATDMA
When debugging is enabled, the adm1026 driver currently logs the
message "Setting VID from GPIO11-15" 108 times each time you run
"sensors". Once should be enough.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Philip Pokorny <ppokorny@penguincomputing.com>
* Add missing new-line to one debug message.
* Remove leading colon from 3 debug messages.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Philip Pokorny <ppokorny@penguincomputing.com>
This is my patch for testing correct values of fan div in adm1029 and
prevent a division by 0 for some (unlikely) register values.
Signed-off-by: Corentin Labbe <corentin.labbe@geomatys.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add at least the bare minimum of documentation for this chip.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch modifies the w83781d driver to use new style driver binding.
Substantial code modifications are required to deal with the new
interface, especially legacy device detection.
[JD: largely edited to make the patch smaller and to get the driver
to work again on ISA devices.]
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Upcoming changes to the I2C part of the w83781d driver will cause ISA
devices to no longer have a struct i2c_client at hand. So, we must
stop (ab)using it now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Probing the ISA bus on systems without ISA bus may hang the system.
This patch makes the ISA bus related code depend on the kernel
configuration parameter CONFIG_ISA. It moves ISA bus related code
into one #ifdef CONFIG_ISA ... #endif block and adds some helper
function.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This information was provided in lm-sensors ticket #2350:
http://www.lm-sensors.org/ticket/2350
This is IMHO still not enough to be able to safely implement fan
control support for the AS99127F, but this is valuable information so
I am adding it to the documentation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The W83781D and W83782D can be accessed either on the I2C bus or the
ISA bus. We must not access the same chip through both interfaces. So
far we were relying on the user passing the correct ignore parameter
to skip the registration of the I2C interface as suggested by
sensors-detect, but this is fragile: the user may load the w83781d
driver without running sensors-detect, and the i2c bus numbers are
not stable across reboots and hardware changes.
So, better detect alias chips in the driver directly, and skip any
I2C chip which is obviously an alias of the ISA chip. This is done
by comparing the value of 26 selected registers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
We can handle the beep enable bit as any other beep mask bit for
slightly smaller code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Add support to set target temperature and tolerance for thermal
cruise mode.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for pwm_enable.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add PWM manual control.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Pins fan/pwm 4-5 can be in use as GPIO. If that is the case, do not
create their sysfs-interface.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The it87 driver doesn't follow the standard sensor type values as
documented in Documentation/hwmon/sysfs-interface. It uses value 2 for
thermistors instead of value 4. This causes "sensors" to tell the user
that the chip is setup for a transistor while it is actually setup for
a thermistor.
Using value 4 for thermistors solves the problem. For compatibility
reasons, we still accept value 2 but emit a warning message so that
users update their configuration files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The new-style lm78 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Upcoming changes to the I2C part of the lm78 driver will cause ISA
devices to no longer have a struct i2c_client at hand. So, we must
stop (ab)using it now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The LM78 detection is relatively weak, and sometimes recent Winbond
chips can be misdetected as an LM78. We have had repeated reports of
this happening. We have an explicit check against this for the ISA
access, do the same for I2C access now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The LM78 and LM79 can be accessed either on the I2C bus or the ISA
bus. We must not access the same chip through both interfaces. So far
we were relying on the user passing the correct ignore parameter to
skip the registration of the I2C interface as suggested by
sensors-detect, but this is fragile: the user may load the lm78
driver without running sensors-detect, and the i2c bus numbers are
not stable across reboots and hardware changes.
So, better detect alias chips in the driver directly, and skip any
I2C chip which is obviously an alias of the ISA chip. This is done
by comparing the value of 26 selected registers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Only request I/O ports 0x295-0x296 instead of the full I/O address
range. This solves a conflict with PNP resources on a few motherboards.
Also request the I/O ports in two parts (4 low ports, 4 high ports)
during device detection, otherwise the PNP resource make the request
(and thus the detection) fail.
This is the exact same fix that was applied to driver w83781d in
March 2008 to address the same problem:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=2961cb22ef02850d90e7a12c28a14d74e327df8d
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Label names ERROR1 and ERROR3 aren't exactly explicit. Change them for
better names that indicate what we are up to.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Function RANGE_TO_REG can easily be simplified. Credits go to Herbert
Poetzl for indirectly suggesting this to me. I tested that the new
implementation returns the same result as the original implementation
for all input values.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
The new-style lm85 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
The Analog Devices and SMSC devices supported by the lm85 driver do
not have the same PWM frequency table as the National Semiconductor
devices. Add support for per-device frequency tables.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
The LM85 and compatible chips only support 8 arbitrary PWM frequencies.
The algorithm to pick one of them based on the user input is not
optimum. Improve it to always pick the closest supported frequency.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Implement the standard PWM frequency interface: pwm[1-*]_freq in
units of 1 Hz, instead of the non-standard pwm[1-*]_auto_pwm_freq
in units of 0.1 Hz. The old naming was not only non-standard, it was
also confusing, because it suggested that the frequency value only
applied in automatic fan speed mode, which isn't true.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Rework the device detection to make it clearer and faster in the
general case (when a known device is found.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Simplify the IRQ handling routine of ams driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use a separate mutex to serialize input device creation/removal,
otheriwse we deadlock if we try to remove input device while it is
being polled. Also do not take ams_info.lock when it is not needed.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
