There are a bunch of drivers that utilize the "ngpios" DT property
without any vendor prefix. Try to start cleaning up the mess by
defining what we mean by this property.
Cc: devicetree@vger.kernel.org
Cc: Pramod Kumar <pramodku@broadcom.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is a few typos in Freescale QorIQ AHCI bindings, This
patch fixes them.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Freescale is renaming the LS2085A SoC to LS2080A.
This patch addresses the same.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
To avoid conflict with other drivers using subnodes of the mtd device
create only one ofpart-specific node rather than any number of
arbitrary partition subnodes.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add dt-binding documentation for s2mps15 PMIC device. The s2mps15 device
is similar to s2mps11/14 PMIC device and has 27 LDO and 10 buck regulators.
This also supports RTC and three 32.768KHz clock outputs.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Subsystem specific bindings for the Arizona devices are being factored
out of the MFD binding document into separate documents for each
subsystem. This patch adds a binding document that covers the existing
extcon specific bindings.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Binding documentation has been added in new subsystem specific binding
documents. This patch removes the now duplicate documentation from the
MFD documentation.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Default the brightness to 2048 and add possibility to override this in
device tree.
Suggested-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Addresses should not be prefixed contain '0x' in nodes.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This patch marks all the reference to the legacy wakeup bindings
and replaces them with the standard "wakeup-source" property.
All these legacy property are also listed under a separate section in
the generic wakeup-source binding document.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Currently different drivers use multiple forms of annotating devices
that should be set up as wakeup sources for the system.
This patch adds a separate binding document inorder to standardize and
consolidate to use "wakeup-source" boolean property to mark the devices
as wakeup capable.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Document a new Device Tree property 'samsung,s2mps11-wrstbi-ground'
indicating that WRSTBI pin of S2MPS13 PMIC is pulled down so
corresponding buck warm reset function should be disabled.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch documents the DT bindings for the Atmel Flexcom which will be
introduced by sama5d2x SoCs. These bindings will be used by the actual
Flexcom driver to be sent in another patch.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some EC implementations include a small nvram space used to store
verified boot context data. This boolean property lets us indicate
whether this space is available or not on a specific EC implementation.
Signed-off-by: Emilio López <emilio.lopez@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is the NFC pull request for 4.4.
It's a bit bigger than usual, the 3 main culprits being:
- A new driver for Intel's Fields Peak NCI chipset. In order to
support this chipset we had to export a few NCI routines and
extend the driver NCI ops to not only support proprietary
commands but also core ones.
- Support for vendor commands for both STM drivers, st-nci
and st21nfca. Those vendor commands allow to run factory tests
through the NFC netlink interface.
- New i2c and SPI support for the Marvell driver, together with
firmware download support for this driver's core.
Besides that we also have:
- A few file renames in the STM drivers, to keep the naming
consistent between drivers.
- Some improvements and fixes on the NCI HCI layer, mostly to
properly reach a secure element over a legacy HCI link.
- A few fixes for the s3fwrn5 and trf7970a drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aw/h
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz says:
====================
NFC 4.4 pull request
This is the NFC pull request for 4.4.
It's a bit bigger than usual, the 3 main culprits being:
- A new driver for Intel's Fields Peak NCI chipset. In order to
support this chipset we had to export a few NCI routines and
extend the driver NCI ops to not only support proprietary
commands but also core ones.
- Support for vendor commands for both STM drivers, st-nci
and st21nfca. Those vendor commands allow to run factory tests
through the NFC netlink interface.
- New i2c and SPI support for the Marvell driver, together with
firmware download support for this driver's core.
Besides that we also have:
- A few file renames in the STM drivers, to keep the naming
consistent between drivers.
- Some improvements and fixes on the NCI HCI layer, mostly to
properly reach a secure element over a legacy HCI link.
- A few fixes for the s3fwrn5 and trf7970a drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
updates the bindings documents and dtsi file according to the review
comments[https://lkml.org/lkml/2015/9/21/670] from Rob Herring <robh@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subsystem specific bindings for the Arizona devices are being factored
out of the MFD binding document into separate documents for each
subsystem. This patch adds a binding document that covers the existing
regulator specific bindings.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a major overhaul of the clk-qoriq driver, which I'm merging
via PPC with Stephen Boyd's ack in order to apply subsequent PPC patches
that depend on it.
The SMP release mechanism for FSL book3e is different from when booting
with normal hardware. In theory we could simulate the normal spin
table mechanism, but not at the addresses U-Boot put in the device tree
-- so there'd need to be even more communication between the kernel and
kexec to set that up. Instead, kexec-tools will set a boolean property
linux,booted-from-kexec in the /chosen node.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: devicetree@vger.kernel.org
HW and driver support the GPIO as interrupt-controller.
Document that in the DT binding.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add device tree binding documentation for the watchdog hardware block
on bcm7038 and newer SoCs.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This new compatible string, "brcm,iproc-gpio", should be used for
all new iproc-based future SoCs.
Signed-off-by: Pramod Kumar <pramodku@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If GPIO controller's pins are muxed, pin-controller subsystem
need to be intimated by defining mapping between gpio and
pinmux controller. This patch adds required properties to
define this mapping via DT.
Signed-off-by: Pramod Kumar <pramodku@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Sometime only need set MMC_CAP_HW_RESET for one of MMC hosts,
So set it in device tree is better.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch updates document devicetree bindings
to support multiple devices.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Align NFC bindgins to use marvell instead of mrvl.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This driver adds the support of SPI-based Marvell NFC controller.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This driver adds the support of I2C-based Marvell NFC controller.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to align with st21nfca, dts configuration properties
ese_present and uicc_present are made available in st-nci driver.
So far, in early development firmware, because
nci_nfcee_mode_set(DISABLE) was not supported we had to try to
enable it during the secure element discovery phase.
After several trials on commercial and qualified firmware it appears
that nci_nfcee_mode_set(ENABLE) and nci_nfcee_mode_set(DISABLE) are
properly supported.
Such feature also help us to eventually save some time (~5ms) when
only one secure element is connected.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With the old binding and driver architecture we had many issues:
No way to assign eDMA channels to event queues, thus not able to tune the
system by moving specific DMA channels to low/high priority servicing. We
moved the cyclic channels to high priority within the code, but that was
just a workaround to this issue.
Memcopy was fundamentally broken: even if the driver scanned the DT/devices
in the booted system for direct DMA users (which is not effective when the
events are going through a crossbar) and created a map of 'used' channels,
this information was not really usable. Since via dmaengien API the eDMA
driver will be called with _some_ channel number, we would try to request
this channel when any channel is requested for memcpy. By luck we got
channel which is not used by any device most of the time so things worked,
but if a device would have been using the given channel, but not requested
it, the memcpy channel would have been waiting for HW event.
The old code had the am33xx/am43xx DMA event router handling embedded. This
should have been done in a separate driver since it is not part of the
actual eDMA IP.
There were no way to 'lock' PaRAM slots to be used by the DSP for example
when booting with DT.
In DT boot the edma node used more than one hwmod which is not a good
practice and the kernel prints warning because of this.
With the new bindings and the changes in the driver we can:
- No regression with Legacy binding and non DT boot
- DMA channels can be assigned to any TC (to set priority)
- PaRAM slots can be reserved for other cores to use
- Dynamic power management for CC and TCs, if only TC0 is used all other TC
can be powered down for example
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The DMA event crossbar on AM33xx/AM43xx is different from the one found in
DRA7x family.
Instead of a single event crossbar it has 64 identical mux attached to each
eDMA event line. When the 0 event mux is selected, the default mapped event
is going to be routed to the corresponding eDMA event line. If different
mux is selected, then the selected event is going to be routed to the given
eDMA event.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This commit adds support for UniPhier outer cache controller.
All the UniPhier SoCs are equipped with the L2 cache, while the L3
cache is currently only integrated on PH1-Pro5 SoC.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'for-upstream/juno-pcie' of git://linux-arm.org/linux-ld:
arm64: defconfig: Enable PCI generic host bridge by default
arm64: Juno: Add support for the PCIe host bridge on Juno R1
Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds support for 4-bit ECC BCH4 for the SPEAr600 SoC. This can
be used by boards equipped with a NAND chip that requires 4-bit ECC
strength. The SPEAr600 HW ECC only supports 1-bit ECC strength.
To enable SW BCH4, you need to specify this in your nand controller
DT node:
nand-ecc-mode = "soft_bch";
nand-ecc-strength = <4>;
nand-ecc-step-size = <512>;
Tested on a custom SPEAr600 board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
[Brian: tweaked the comments a bit]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
synopsys-dw-mshc supports three types of transfer mode. We add
bindings and description for how to use them at runtime.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Renesas R8A7794 SoC also has the MMCIF controller.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The "compatible" property text contradicts even the example given in the MMCIF
binding document itself; moreover, the Renesas MMCIF driver only matches on
the generic "compatible" string and doesn't look for the SoC specific strings
at all. Thus describe "renesas,sh-mmcif" as a fallback value.
Fixes: b4c27763d7 ("mmc: sh_mmcif: Document DT bindings")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add ciu_drive, ciu_sample clocks and default-sample-phase. This will later
be used by tuning code.
We do not touch ciu_drive (and by extension define default-drive-phase).
Drive phase is mostly used to define minimum hold times, while one could
write some code to determine what phase meets the minimum hold time
(ex 10 degrees) this will not work with the current clock phase framework
(which floors angles, so we'll get 0 deg, and there's no way to know what
resolution the floors happen at). We assume that the default drive angles
set by the hardware are good enough.
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ARM's Juno R1 board used PLDA XpressRICH3-AXI IP to implement a PCIe host
bridge. Introduce "plda" as vendor prefix for PLDA and document the DT
bindings for PLDA XpressRICH3-AXI IP as well as ARM's Juno R1.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
This pull request contains the DT changes for BCM2835 in 4.4. It
pulls in clk/clk-bcm2835 (which Stephen Boyd has said would be stable)
because the DT changes to enable the clock driver need the driver
itself to be present. These changes include the following:
- Eric Anholt, moves the bcm2835 clock driver under bcm/ where it belongs with
other Broadcom clock providers drivers, defines the binding for new clock
driver, adds support for programming the BCM2835 audio domain, adds the DDC I2C
controller to Device Tree, and finally migrates the Device Tree to use the new
clock driver binding
- Lubomir Rintel adds support for the Raspberry Pi Model A+ and B revision 2, and
remove the I2S controller which is non-existent on Raspberry Pi Model B
- Stefan Wahren adds an uart0 label for referencing the UART adapter
* tag 'arm/soc/for-4.4/rpi-dt-v2' of https://github.com/Broadcom/stblinux:
ARM: bcm2835: Add the DDC I2C controller to the device tree.
ARM: bcm2835: Switch to using the new clock driver support.
ARM: bcm2835: dt: Add Raspberry Pi Model A+
ARM: bcm2835: dt: Add Raspberry Pi Model B rev2
ARM: bcm2835: dt: Raspberry Pi Model B had no I2S
ARM: bcm2835: add label for uart0
clk: bcm2835: Add support for programming the audio domain clocks
clk: bcm2835: Add binding docs for the new platform clock driver.
clk: bcm2835: Move under bcm/ with other Broadcom SoC clk drivers.
Signed-off-by: Olof Johansson <olof@lixom.net>
