EMMC can have two voltage supplies, Vcc and VccQ
which are implemented in the code as consumer
supplies vmmc and vmmc_aux.
If the regulator that supplies vmmc_aux is shared
with other consumers, then sending it to sleep
will disrupt those consumers. However, the
TWL4030-family regulators may have OFF remapped
to SLEEP, in which case 'regulator_disable()'
will put the regulator to sleep only when all
consumers are disabled - which is the desired
behaviour.
This patch adds a platform data field to allow
that option.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
An eMMC may be always powered on, so that the lowest
power saving state possible is sleeping. Add a field
to the platform data to indicate that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It has been discovered that, when eMMC is powered off, current
will flow from OMAP eMMC data pull-ups to the eMMC voltage supply.
Configuring pads for OMAP off-mode does not help because eMMC is
powered off independently of OMAP off-mode. Hence the pads are
now re-configured when eMMC is powered on or off.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Call the PM context-loss count function, now that there
is a prototype for it.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
hsmmc.[ch] no longer has any dependency on twl4030
and variable names should be renamed to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
mmc-twl4030.[ch] no longer has any dependency on twl4030
and should be renamed to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch moves the setup code for GPIO's and Voltage
Regulators from the board file mmc-twl4030.c to the
driver omap_hsmmc.c. PBIAS and other system control
configuration remains in the board file.
Moving GPIO code to the driver makes the board initialisation
code independent of when GPIO's are defined. That makes the
board initialisation now entirely independent of its original
twl4030 roots.
Moving Voltage Regulator code to the driver allows for further
development of regulator support in the core MMC code. It also
permits the MMC core to be compiled as a module, because the
board code no longer calls MMC core functions.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for flashes on 3430SDP boards. All three
NAND, NOR and OneNAND are supported. I have tested it on
3430SDP (ES2 and ES3.1).
This patch can be treated as an example to "how to utilize":
'gpmc-nand.c' and 'board-sdp-flash.c'.
Similar patches can be created for 2430sdp and 3630sdp or any other
similar board.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds 'board-sdp-flash.c', which could be utilized
by boards similar to 3430SDP. (For ex: 2430sdp, 36030sdp).
This file does initialization for all three flash devices present
in SDP boards (NOR, NAND, OneNAND), by finding there 'cs' number
dynamically using switch setting information (S8: 1-4).
This also expects partition information from core board files (for
ex: board-3430sdp.c). Which allows to choose different default
partitions for different boards.
A new structure is created for this purpose: 'flash_partitions'
in 'mach/board-sdp.h'. This has two members:
1. struct mtd_partition *parts
2. int nr_parts
A board file is expected to fill this structure and pass it to
'sdp-flsash-init'. Partition information should be passed in
structure array of 'flash_partitions'. Partition information should
be passed in below sequence in array:
NOR
OneNAND
NAND
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Introducing 'gpmc-nand.c' for GPMC specific NAND init.
For example: GPMC timing parameters and all.
This patch also migrates gpmc related calls from 'nand/omap2.c'
to 'gpmc-nand.c'.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Get rid of the following warnings:
arch/arm/mach-omap2/gpmc.c:550:30: warning: non-ANSI
function declaration of function 'omap3_gpmc_save_context'
arch/arm/mach-omap2/gpmc.c:581:33: warning: non-ANSI
function declaration of function 'omap3_gpmc_restore_context'
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Determine cache size required per McBSP port at init time, based on
processor type running on.
Allocate space for storing cached copies of McBSP register values at
port request.
Modify omap_msbcp_write() function to update the cache with every
register write operation.
Modify omap_mcbsp_read() to support reading from cache or hardware.
Update MCBSP_READ() macro for modified omap_mcbsp_read() function API.
Introduce a new macro that reads from the cache.
Tested on OMAP1510 based Amstrad Delta using linux-omap for-next, commit
fb7380d70e041e4b3892f6b19dff7efb609d15a4 (2.6.33-rc3+ dated 2010-01-11).
Compile-tested with: omap_perseus2_730_defconfig, omap_generic_1610_defconfig,
omap_generic_2420_defconfig, omap_2430sdp_defconfig, omap_3430sdp_defconfig,
omap_4430sdp_defconfig with CONFIG_OMAP_MCBSP=y selected.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert OMAP based boards to use physmap-flash. Refreshed against today's
Linux omap kernel tree
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename clkops_noncore_dpll_ops for omap3 and omap4.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Allow booting omap4 with multi-omap configuration.
Tested only on omap2 and omap3, please somebody test
on omap4 and ack.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move defines around and set up handlers based on MULTI_OMAP2.
Note that this will only allow compiling in omap4 with omap2 and
omap3. It will not yet make omap4 boot with multi-omap.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define the irq base the same way as for omap2 and omap3,
and start using get_irqnr_preamble.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make get_irqnr_and_base common for mach-omap2 multiboot
Thanks to a tip from Russell King <rmk+kernel@arm.linux.org.uk>,
this also optimizes the code for non-multiboot configurations by
using get_irqnr_preamble.
Note that this will only work currently for 24xx and 34xx.
Support for 44xx can be added later on for basic multiboot,
and similar patch should be done for mach-omap1/entry-macro.S.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define arch_decomp_setup() the same way as some other
architectures do. Use arch_id to configure the debug uart
based on the machine_is by storing it into the uart
scratchpad register for DEBUG_LL code to use.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we don't have conflicts with the defines
with compiling in multiple omaps. Set the addresses
for uarts in struct omap_globals for the early serial
init code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise more complicated uart configuration won't be possible.
We can use r1 for tmp register for both head.S and debug.S.
NOTE: This patch depends on another patch to add the the tmp register
into all debug-macro.S files. That can be done with:
$ sed -i -e "s/addruart,rx|addruart, rx/addruart, rx, tmp/"
arch/arm/*/include/*/debug-macro.S
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The regulator is now enabled by DSS driver, and thus the panel driver
doesn't need to touch it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
The platform data allocated with kmalloc() will become unreachable once
the init is complete, so it should be freed. The problem was discovered
by kmemleak.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the omap serial clocks are autoidled after 5 seconds.
However, this causes lost characters on the serial ports. As this
is considered non-standard behaviour for Linux, disable the timeout.
Note that this will also cause blocking of any deeper omap sleep
states.
To enable the autoidling of the serial ports, do something like
this for each serial port:
# echo 5 > /sys/devices/platform/serial8250.0/sleep_timeout
# echo 5 > /sys/devices/platform/serial8250.1/sleep_timeout
...
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
David Binderman ran the sourceforge tool cppcheck over the source code of the
new Linux kernel 2.6.33-rc6:
[./arm/mach-omap2/mux.c:492]: (error) Buffer access out-of-bounds
13 characters + 1 digit + 1 zero byte is more than 14 characters.
Also add a comment on mode0 name length in case new omaps
start using longer names.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
3630 has more mux signals than 34xx. The additional pins
exist in omap36xx_cbp_subset, but are not initialized
as the superset is missing these offsets. This causes
the following errors during the boot:
mux: Unknown entry offset 0x236
mux: Unknown entry offset 0x22e
mux: Unknown entry offset 0x1ec
mux: Unknown entry offset 0x1ee
mux: Unknown entry offset 0x1f4
mux: Unknown entry offset 0x1f6
mux: Unknown entry offset 0x1f8
mux: Unknown entry offset 0x1fa
mux: Unknown entry offset 0x1fc
mux: Unknown entry offset 0x22a
mux: Unknown entry offset 0x226
mux: Unknown entry offset 0x230
mux: Unknown entry offset 0x22c
mux: Unknown entry offset 0x228
Fix this by adding the missing offsets to omap3 superset.
Note that additionally the uninitialized pins need to be
skipped on 34xx.
Based on an earlier patch by Allen Pais <allen.pais@ti.com>.
Reported-by: Allen Pais <allen.pais@ti.com>
Signed-off-by: Allen Pais <allen.pais@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Ensure valid clock pointer during GPMC init. Fixes compiler
warning about potential use of uninitialized variable.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Ensure valid base address during IRQ init. Fixes compiler warning
about potential use of uninitialized variable.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert CONFIG_ARCH_OMAP34XX to CONFIG_ARCH_OMAP3, and
CONFIG_ARCH_OMAP24XX to CONFIG_ARCH_OMAP2, in preparation for Tony's
multi-OMAP patches.
While here, update some copyrights, convert instances of "34xx" to
"3xxx" where applicable, and convert preprocessor directives of the
form
#if defined(CONFIG_ARCH_OMAP2) | defined(CONFIG_ARCH_OMAP3)
to
#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
for standardization.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
The macros defining the shift bits in registers for various
register bit fields are defined as 1 << n.
Instead define them as n. They can then be used as val << n.
The changes are generated by updating the script which autogenerates
the files modifed in the patch.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rename the omap2_clk_init() in the OMAP2, 3, and 4 clock code to be
omap2xxx_clk_init(), omap3xxx_clk_init(), etc. Remove all traces of
the (commented) old virt_prcm_set code from omap3xxx_clk_init() and
omap4xxx_clk_init(), since this will be handled with the OPP code that
is cooking in the PM branch.
After this patch, there should be very little else in the clock code
that blocks a multi-OMAP 2+3 kernel. (OMAP2420+OMAP2430 still has some
outstanding issues that need to be resolved; this is pending on some
additions to the hwmod data.)
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Move all static functions up to the top of the file to match the
practice in other OMAP clock code. Make omap3_noncore_dpll_program()
static (noted by sparse) and prepend an underscore to the function
name to mark that it is file-local.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
omap2_clk_prepare_for_reboot() is only applicable to OMAP2xxx chips,
so rename it to omap2xxx_clk_prepare_for_reboot() and only call it when
running on OMAP2xxx chips. Remove the old stub in the OMAP3 clock code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
