This patch fixes following issues when HS200 is enabled:
1. If executing_tuning() host ops is called without mmc_host_clk_hold(),
card clocks might get turned off (if MMC_CLK_GATING is enabled)
while execute_tuning() is in progress. So this patch makes sure
that execute_tuning() is called with mmc_host_clk_hold().
2. If host timing mode is set to HS200 mode, there should not be
any communication with the card until execute_tuning() is completed.
But there is a chance that CMD6 might be sent to enable set HPI_EN
(of HPI_MGMT field in EXT_CSD) before execute_tuning() is called.
So this patch moves this operation after execute_tuning() is completed.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: girish.shivananjappa@linaro.org
Signed-off-by: Chris Ball <cjb@laptop.org>
Otherwise we can get following warning when re-loading the omap_hsmmc
driver module when gpio_twl4030 module is not loaded:
omap_hsmmc omap_hsmmc.0: Unbalanced pm_runtime_enable!
omap_hsmmc omap_hsmmc.0: Unable to grab MMC CD IRQ
omap_hsmmc: probe of omap_hsmmc.0 failed with error -22
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Make sure mmc_start_req cancels the prepared job, if the request
was prevented to be started due to the card has been removed.
This bug was introduced in commit:
mmc: allow upper layers to know immediately if card has been removed
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Per Forlin <per.forlin@stericsson.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Most parts of the enable / disable API are no longer used and
can be removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If TMIO MMC is used in polling mode, or the card is non-removable, or
card-detection is performed, using an external interrupt, there is no
need to enable controller native card hotplug interrupts.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC1 is not the only instance that can be used/wired for SD.
So remove this assumption from the driver.
Now that all the mmc id based usage is removed, get rid of all the DEVID
defines and also the 'id' field from the omap_hsmmc_host structure.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Now that omap_hsmmc_set_power() already has a check to return 0
if !host->vcc, it seems like it can be used even on MMC4 instead
of the dummy omap_hsmmc_4_set_power().
This also helps get rid of all the host->id based check to
populate the right function for on-chip/external level
shifting and use omap_hsmmc_set_power() for all MMC modules.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use omap_hsmmc_235_set_poweri() (now renamed as omap_hsmmc_set_power())
for MMC1 instance as well and get rid of omap_hsmmc_1_set_power()
completely.
omap_hsmmc_235_set_power() seems to be implemented as a superset of
omap_hsmmc_1_set_power() with additional functionality implemented
based on additional checks and hence should just work for MMC1
as well.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use OMAP_HSMMC_SUPPORTS_DUAL_VOLT flag instead of host->id
for identifying SD bus voltage capabilities.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
set_sleep seems to be unused in omap_hsmmc driver. so get rid of it.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Git rid of hardcoded tx/rx DMA channels based on pdev->id
and use platform_get_resource_byname() to retrieve them
instead.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
To prevent I/O as soon as possible at card removal, a new detect work is
re-scheduled without a delay to let a rescan remove the card device as
soon as possible.
Additionally, MMC_CAP2_DETECT_ON_ERR can now be used to handle "slowly"
removed cards that a scheduled detect work did not detect as removed.
To prevent further I/O requests for these lingering removed cards,
check if card has been removed and then schedule a detect work to
properly remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
3ec7699d3bb1b0ee7 ("mmc: dw_mmc: Add support for pre_req and post_req")
broke non-IDMAC DMA, because dw_mci_pre_dma_transfer() is valid only if
using internal DMA. In case of using other DMA it returns -ENOSYS. It
prevents the DMA operations. This patch makes dw_mci_pre_dma_transfer()
effective in all DMA cases again.
Reported-by: James Hogan <james@albanarts.com>
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When disable CONFIG_MMC_DW_IDMAC, can see the compiler error.
Because in dw_mci_post_req(), called the dw_mci_get_dma_dir().
But that function is in #ifdef CONFIG_MMC_DW_IDMAC.
I think that function is generic function.
Not need the CONFIG_MMC_DW_IDMAC.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
External circuitry like level shifters may limit the maximum operation
speed of the hsmmc controller. Add a field to struct omap2_hsmmc_info
so boards can adjust the setting on demand.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
commit 6bd081277e "dmaengine: imx-dma: merge old dma-v1.c with
imx-dma.c" removed the dependency in config for the imx dma driver,
whereas it should depend on ARCH_MXS
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Fix failure in aa_change_onexec api when the request is made from a confined
task. This failure was caused by two problems
The AA_MAY_ONEXEC perm was not being mapped correctly for this case.
The executable name was being checked as second time instead of using the
requested onexec profile name, which may not be the same as the exec
profile name. This mistake can not be exploited to grant extra permission
because of the above flaw where the ONEXEC permission was not being mapped
so it will not be granted.
BugLink: http://bugs.launchpad.net/bugs/963756
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
commit 74a622b (ia64: vsyscall: Use seqcount instead of seqlock) broke
the ia64 build.
Reported-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Avoid extra work by continuing on to the next rt_rq if the highest
prio task in current rt_rq is the same priority as our candidate
task.
More detailed explanation: if next is not NULL, then we have found a
candidate task, and its priority is next->prio. Now we are looking
for an even higher priority task in the other rt_rq's. idx is the
highest priority in the current candidate rt_rq. In the current 3.3
code, if idx is equal to next->prio, we would start scanning the tasks
in that rt_rq and replace the current candidate task with a task from
that rt_rq. But the new task would only have a priority that is equal
to our previous candidate task, so we have not advanced our goal of
finding a higher prio task. So we should avoid the extra work by
continuing on to the next rt_rq if idx is equal to next->prio.
Signed-off-by: Michael J Wang <mjwang@broadcom.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/2EF88150C0EF2C43A218742ED384C1BC0FC83D6B@IRVEXCHMB08.corp.ad.broadcom.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 5fbd036b55 ("sched: Cleanup cpu_active madness"), which was
supposed to finally sort the cpu_active mess, instead uncovered more.
Since CPU_STARTING is ran before setting the cpu online, there's a
(small) window where the cpu has active,!online.
If during this time there's a wakeup of a task that used to reside on
that cpu select_task_rq() will use select_fallback_rq() to compute an
alternative cpu to run on since we find !online.
select_fallback_rq() however will compute the new cpu against
cpu_active, this means that it can return the same cpu it started out
with, the !online one, since that cpu is in fact marked active.
This results in us trying to scheduling a task on an offline cpu and
triggering a WARN in the IPI code.
The solution proposed by Chuansheng Liu of setting cpu_active in
set_cpu_online() is buggy, firstly not all archs actually use
set_cpu_online(), secondly, not all archs call set_cpu_online() with
IRQs disabled, this means we would introduce either the same race or
the race from fd8a7de17 ("x86: cpu-hotplug: Prevent softirq wakeup on
wrong CPU") -- albeit much narrower.
[ By setting online first and active later we have a window of
online,!active, fresh and bound kthreads have task_cpu() of 0 and
since cpu0 isn't in tsk_cpus_allowed() we end up in
select_fallback_rq() which excludes !active, resulting in a reset
of ->cpus_allowed and the thread running all over the place. ]
The solution is to re-work select_fallback_rq() to require active
_and_ online. This makes the active,!online case work as expected,
OTOH archs running CPU_STARTING after setting online are now
vulnerable to the issue from fd8a7de17 -- these are alpha and
blackfin.
Reported-by: Chuansheng Liu <chuansheng.liu@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: linux-alpha@vger.kernel.org
Link: http://lkml.kernel.org/n/tip-hubqk1i10o4dpvlm06gq7v6j@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We should not ever enable IRQs until we're fully set up. This opens up
a window where interrupts can hit the cpu and interrupts can do
wakeups, wakeups need state that isn't set-up yet, in particular this
cpu isn't elegible to run tasks, so if any cpu-affine task that got
created in CPU_UP_PREPARE manages to get a wakeup, its affinity mask
will get broken and we'll run into lots of 'interesting' problems.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-yaezmlbriluh166tfkgni22m@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There have been a few reports of this warning appearing recently:
XFS (dm-4): xlog_space_left: head behind tail
tail_cycle = 129, tail_bytes = 20163072
GH cycle = 129, GH bytes = 20162880
The common cause appears to be lots of freeze and unfreeze cycles,
and the output from the warnings indicates that we are leaking
around 8 bytes of log space per freeze/unfreeze cycle.
When we freeze the filesystem, we write an unmount record and that
uses xlog_write directly - a special type of transaction,
effectively. What it doesn't do, however, is correctly account for
the log space it uses. The unmount record writes an 8 byte structure
with a special magic number into the log, and the space this
consumes is not accounted for in the log ticket tracking the
operation. Hence we leak 8 bytes every unmount record that is
written.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>
When we read inodes via bulkstat, we generally only read them once
and then throw them away - they never get used again. If we retain
them in cache, then it simply causes the working set of inodes and
other cached items to be reclaimed just so the inode cache can grow.
Avoid this problem by marking inodes read by bulkstat not to be
cached and check this flag in .drop_inode to determine whether the
inode should be added to the VFS LRU or not. If the inode lookup
hits an already cached inode, then don't set the flag. If the inode
lookup hits an inode marked with no cache flag, remove the flag and
allow it to be cached once the current reference goes away.
Inodes marked as not cached will get cleaned up by the background
inode reclaim or via memory pressure, so they will still generate
some short term cache pressure. They will, however, be reclaimed
much sooner and in preference to cache hot inodes.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>
There have some acer laptop have broken _BCM implemenation, the AML
code wrote value to EC register but firmware didn't change brighenss.
Fortunately, the brightness control works on those machines with
vendor mode. So, add quirk table for video backlight vendor mode
and unregister acpi video interface on those machines.
Tested on Acer TravelMate 4750
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Clock stretching is not supposed to last long, so asking to be
rescheduled while waiting for the clock line to be released by a slave
makes little sense. Odds are that the clock line will long have been
released when we run again, so we will have lost time and may even
get an SMBus timeout because of this.
So just busy-wait in that case. This also participates in the effort
to make i2c-algo-bit usable in contexts that can't sleep.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
This patch converts the drivers in drivers/i2c/muxes/* to use the
module_i2c_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Michael Lawnick <ml.lawnick@gmx.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use usleep_range instead of msleep when waiting for command
completion. Most SMBus commands complete in less than 2 jiffies so
this brings a pleasant performance boost.
Strongly inspired from a similar change by Olivier Sobrie to the
i2c-isch driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Olivier Sobrie <olivier@sobrie.be>
Add the SMBus controller device IDs for the Intel Lynx Point PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Generally it is not needed to wait for 1 msec, the SMBus get often ready
in less than 200 usecs.
msleep(1) can wait up to 20 msecs... It has a significant impact when
there is a burst of transactions on the bus.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Direct inclusion of asm/gpio.h has been deprecated for a while now due
to the cross platform gpiolib.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
In drivers/platform/x86/amilo-rfkill.c::amilo_rfkill_probe() the call
to dmi_first_match() may fail and return NULL. If it does return NULL,
then we'll be dereferencing a NULL pointer in the rfkill_alloc() call
where we do 'system_id->driver_data' --> KABOOM!
Avoid that problem by testing for a NULL return value from
dmi_first_match() and bailing out if it fails.
I was a bit uncertain about what to return in the failure case. In the
end I settled for -ENXIO as the most logical error to return.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
On these laptops, the ACPI video is not functional, and very unlikely
to be fixed by the vendor. Note that intel_backlight works for some
of these laptops, and the backlight from samsung-laptop always work.
The good news is that newer laptops have functional ACPI video device
and won't end up growing this list.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The wireless rfkill should charged by sony-laptop but not acer-wmi.
So, add Sony's SNY5001 acpi device to blacklist in acer-wmi.
Tested on Sony Vaio
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Mattia Dongili <malattia@linux.it>
Cc: Dimitris N <ddarlac@gmail.com>
Tested-by: Dimitris N <ddarlac@gmail.com>
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The newer V series bios reports product version as 'Lenovo'
instead of 'ThinkPad'. Recoginze this new string so that
the module can load.
Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Tested-by: James Ferguson <james.ferguson@canonical.com>
Tested-by: Dennis Chua <dennis.chua@canonical.com>
Tested-by: Ike Pan <ike.pan@canonical.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
But we can still do it on other boards, as this might happen
if the backlight driver change when update_bl is called.
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Some models work better with different values of wapf, so move the
variable into quriks_entry to make it more easy to give a specific
value to different models.
Based on original patch from AceLan Kao <acelan.kao@canonical.com>
Cc: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Due to some implementation reasons, ASUS ET2012 All-in-One machines
can't report the correct backlight power status, it will always return
1. To track the backlight power status correctly, we have to store the
status by ourselves.
BTW, by the BIOS design, the backlight power will be turn on/off
sequently, no matter what the value of the parameter will be.
More over, the brightness adjustment command will turn on the backlight
power. Those behaviors will make us fail to track the backlight power
status.
For example, While we are trying to turn on the backlight power,
we will send out the brightness adjustment command and then trying to
figure out if we have to turn on the backlight power, then send out
the command. But, the real case is that, the backlight power turns on
while sending the brightness adjustment command, and then we send out
the command to turn on the backlight power, it actually will turn off
the backlight power and the backlight power status we recorded becomes
wrong. So, we have to seperate these two commands by a if statement.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Some ASUS ET2012E/I All-in-One machines that use a scalar board
to control the brightness, and they only accept brightness up and down
command. So, I introduced a get_scalar_command() function to pass the
command to the scalar board through WMI.
Besides, we have to store the brightness value locally, for we need the
old value to know the brightness value is increasing or decreasing.
BTW, since there is no way to retrieve the actual brightness(it would be
a fixed value), and the max brightness value would be fixed to 1, so we
have to keep passing the brightness up/down command when we reached the
max brightness value or 0.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This function returns a umode_t (unsigned short) instead of mode_t which
is an unsigned int on some architectures. Cleaning this up silences a
compile warning:
drivers/platform/x86/samsung-laptop.c:1108:2: warning: initialization
from incompatible pointer type [enabled by default]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
linux/ctype.h is needed for isalnum() to avoid a build error:
drivers/platform/x86/samsung-laptop.c: In function ‘samsung_sabi_diag’:
drivers/platform/x86/samsung-laptop.c:1306: error: implicit declaration of function ‘isalnum’
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Fields d0, d1, d2, and d3 are members of an anonymous struct inside an
anonymous union inside struct sabi_data. Initialization must be done by
wrapping the anonymous union and structs with brackets to avoid a build
error:
drivers/platform/x86/samsung-laptop.c: In function ‘sabi_set_commandb’:
drivers/platform/x86/samsung-laptop.c:433: error: unknown field ‘d0’ specified in initializer
drivers/platform/x86/samsung-laptop.c:433: warning: missing braces around initializer
drivers/platform/x86/samsung-laptop.c:433: warning: (near initialization for ‘in.<anonymous>’)
...
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
