'xhci_del_comp_mod_timer' is local to this file.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The USB core currently handles enabling and disabling optional USB power
management features during device transitions (device suspend/resume,
driver bind/unbind, device reset, and device disconnect). Those
optional power features include Latency Tolerance Messaging (LTM),
USB 3.0 Link PM, and USB 2.0 Link PM.
The USB core currently enables LPM on device enumeration and disables
USB 2.0 Link PM when the device is reset. However, the xHCI driver
disables LPM when the device is disconnected and the device context is
freed. Push the call up into the USB core, in order to be consistent
with the core handling all power management enabling and disabling.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
How it's supposed to work:
--------------------------
USB 2.0 Link PM is a lower power state that some newer USB 2.0 devices
support. USB 3.0 devices certified by the USB-IF are required to
support it if they are plugged into a USB 2.0 only port, or a USB 2.0
cable is used. USB 2.0 Link PM requires both a USB device and a host
controller that supports USB 2.0 hardware-enabled LPM.
USB 2.0 Link PM is designed to be enabled once by software, and the host
hardware handles transitions to the L1 state automatically. The premise
of USB 2.0 Link PM is to be able to put the device into a lower power
link state when the bus is idle or the device NAKs USB IN transfers for
a specified amount of time.
...but hardware is broken:
--------------------------
It turns out many USB 3.0 devices claim to support USB 2.0 Link PM (by
setting the LPM bit in their USB 2.0 BOS descriptor), but they don't
actually implement it correctly. This manifests as the USB device
refusing to respond to transfers when it is plugged into a USB 2.0 only
port under the Haswell-ULT/Lynx Point LP xHCI host.
These devices pass the xHCI driver's simple test to enable USB 2.0 Link
PM, wait for the port to enter L1, and then bring it back into L0. They
only start to break when L1 entry is interleaved with transfers.
Some devices then fail to respond to the next control transfer (usually
a Set Configuration). This results in devices never enumerating.
Other mass storage devices (such as a later model Western Digital My
Passport USB 3.0 hard drive) respond fine to going into L1 between
control transfers. They ACK the entry, come out of L1 when the host
needs to send a control transfer, and respond properly to those control
transfers. However, when the first READ10 SCSI command is sent, the
device NAKs the data phase while it's reading from the spinning disk.
Eventually, the host requests to put the link into L1, and the device
ACKs that request. Then it never responds to the data phase of the
READ10 command. This results in not being able to read from the drive.
Some mass storage devices (like the Corsair Survivor USB 3.0 flash
drive) are well behaved. They ACK the entry into L1 during control
transfers, and when SCSI commands start coming in, they NAK the requests
to go into L1, because they need to be at full power.
Not all USB 3.0 devices advertise USB 2.0 link PM support. My Point
Grey USB 3.0 webcam advertises itself as a USB 2.1 device, but doesn't
have a USB 2.0 BOS descriptor, so we don't enable USB 2.0 Link PM. I
suspect that means the device isn't certified.
What do we do about it?
-----------------------
There's really no good way for the kernel to test these devices.
Therefore, the kernel needs to disable USB 2.0 Link PM by default, and
distros will have to enable it by writing 1 to the sysfs file
/sys/bus/usb/devices/../power/usb2_hardware_lpm. Rip out the xHCI Link
PM test, since it's not sufficient to detect these buggy devices, and
don't automatically enable LPM after the device is addressed.
This patch should be backported to kernels as old as 3.11, that
contain the commit a558ccdcc7 "usb: xhci:
add USB2 Link power management BESL support". Without this fix, some
USB 3.0 devices will not enumerate or work properly under USB 2.0 ports
on Haswell-ULT systems.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
To enable USB 2.0 Link Power Management (LPM), the xHCI host controller
needs the device slot ID to generate the device address used in L1 entry
tokens. That information is set in the L1 device slot ID field of the
USB 2.0 LPM registers.
Currently, the L1 device slot ID is overwritten when the xHCI driver
initiates the software test of USB 2.0 Link PM in
xhci_usb2_software_lpm_test. It is never cleared when USB 2.0 Link PM
is disabled for the device. That should be harmless, because the
Hardware LPM Enable (HLE) bit is cleared when USB 2.0 Link PM is
disabled, so the host should not pay attention to the slot ID.
This patch should have no effect on host behavior, but since
xhci_usb2_software_lpm_test is going away in an upcoming bug fix patch,
we need to move that code to the function that enables and disables USB
2.0 Link PM.
This patch should be backported to kernels as old as 3.11, that contain
the commit a558ccdcc7 "usb: xhci: add USB2
Link power management BESL support". The upcoming bug fix patch is also
marked for that stable kernel.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The non-DT for EXYNOS SoCs is not supported from v3.11.
Thus, there is no need to support non-DT for Exynos OHCI driver.
The 'include/linux/platform_data/usb-ohci-exynos.h' file has been
used for non-DT support. Thus, the 'usb-ohci-exynos.h' file can
be removed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes the initial delay before the startup of a newly
scheduled isochronous stream. Currently the stream doesn't start
for at least 5 ms (40 microframes). This value is just an estimate;
it has no real justification.
Instead, we can start the stream as soon as possible after the
scheduling computations are complete. Essentially this requires
nothing more than reading the frame counter after the stream is
scheduled, instead of before.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch continues the scheduling changes in ehci-hcd by adding a
table to store the bandwidth allocation below each TT. This will
speed up the scheduling code, as it will no longer need to read
through the entire schedule to compute the bandwidth currently in use.
Properly speaking, the FS/LS budget calculations should be done in
terms of full-speed bytes per microframe, as described in the USB-2
spec. However the driver currently uses microseconds per microframe,
and the scheduling code isn't robust enough at this point to change
over. For the time being, we leave the calculations as they are.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 476e4bf939.
Manjunath is no longer at Linaro, the email address bounces. Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.
I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
This reverts commit 056ca85dab.
Manjunath is no longer at Linaro, the email address bounces. Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.
I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
This reverts commit 19d3394304.
Manjunath is no longer at Linaro, the email address bounces. Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.
I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
This reverts commit 86a63f1021.
Manjunath is no longer at Linaro, the email address bounces. Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.
I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
This reverts commit 018258b436.
Manjunath is no longer at Linaro, the email address bounces. Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.
I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
This reverts commit fea0896fd3.
Manjunath is no longer at Linaro, the email address bounces. Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.
I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
This reverts commit 36a8758736.
Manjunath is no longer at Linaro, the email address bounces. Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.
I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Currently, Samsung is using 'EXYNOS' as the name of Samsung SoCs.
Thus, ehci-exynos is preferred than ehci-s5p.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The non-DT for EXYNOS SoCs is not supported from v3.11.
Thus, there is no need to support non-DT for Exynos EHCI driver.
The 'include/linux/platform_data/usb-ehci-s5p.h' file has been
used for non-DT support. Thus, the 'usb-ehci-s5p.h' file can
be removed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch significantly changes the scheduling code in ehci-hcd.
Instead of calculating the current bandwidth utilization by trudging
through the schedule and adding up the times used by the existing
transfers, we will now maintain a table holding the time used for each
of 64 microframes. This will drastically speed up the bandwidth
computations.
In addition, it eliminates a theoretical bug. An isochronous endpoint
may have bandwidth reserved even at times when it has no transfers
listed in the schedule. The table will keep track of the reserved
bandwidth, whereas adding up entries in the schedule would miss it.
As a corollary, we can keep bandwidth reserved for endpoints even
when they aren't in active use. Eventually the bandwidth will be
reserved when a new alternate setting is installed; for now the
endpoint's reservation takes place when its first URB is submitted.
A drawback of this approach is that transfers with an interval larger
than 64 microframes will have to be charged for bandwidth as though
the interval was 64. In practice this shouldn't matter much;
transfers with longer intervals tend to be rather short anyway (things
like hubs or HID devices).
Another minor drawback is that we will keep track of two different
period and phase values: the actual ones and the ones used for
bandwidth allocation (which are limited to 64). This adds only a
small amount of overhead: 3 bytes for each endpoint.
The patch also adds a new debugfs file named "bandwidth" to display
the information stored in the new table.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch begins the process of unifying the scheduling parameters
that ehci-hcd uses for interrupt and isochronous transfers. It
creates an ehci_per_sched structure, which will be stored in both
ehci_qh and ehci_iso_stream structures, and will contain the common
scheduling information needed for both.
Initially we merely create the new structure and move some existing
fields into it. Later patches will add more fields and utilize these
structures in improved scheduling algorithms.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ehci-hcd is inconsistent in the sentinel values it uses to indicate
that no frame number has been assigned for a periodic transfer. Some
places it uses NO_FRAME (defined as 65535), other places it uses -1,
and elsewhere it uses 9999.
This patch defines a value for NO_FRAME which can fit in a 16-bit
signed integer, and changes the code to use it everywhere.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ehci-hcd uses a value of 0 in an endpoint's toggle flag to indicate
that the endpoint has been reset (and therefore the Data Toggle bit
needs to be cleared in the endpoint's QH overlay region).
The toggle flag should be set to 0 only when ehci_endpoint_reset()
succeeds. This patch moves the usb_settoggle() call into the
appropriate branch of the "if" statement.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The scheduling code in ehci-hcd contains an error. For full-speed
isochronous-OUT transfers, the EHCI spec forbids scheduling
Start-Split transactions in H-microframe 7, but the driver allows it
anyway. This patch adds a check to prevent it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although the bandwidth statistics maintained by ehci-hcd show up only
in the /sys/kernel/debug/usb/devices file, they ought to be calculated
correctly. The calculation for full-speed isochronous endpoints is
wrong; it mistakenly yields bytes per microframe instead of bytes per
frame. The "interval" value, which is in frames, should not be
converted to microframes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check_intr_schedule() routine in ehci-hcd looks at the wrong
microframes when checking to see if a full-speed or low-speed
interrupt endpoint will fit in the periodic schedule. If the
Start-Split transaction is scheduled for microframe N then the
Complete-Split transactions get scheduled for microframes N+2, N+3, and
N+4. However the code considers N+1, N+2, and N+3 instead.
This patch fixes the limits on the "for" loop and also improves the
use of whitespace.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When devm_usb_get_phy() fails, usb_put_hcd() should be called
to prevent memory leak.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allows MSM EHCI controller to be specified via device tree.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use struct usb_hcd::phy to hold USB PHY instance.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These aren't necessary after switch and if blocks.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Clock tree support
- Clock management support using PM core
- Keystone config update for EMDA with ack from Vinod
- Enable SPI and I2C drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=d2uA
-----END PGP SIGNATURE-----
Merge tag 'keystone-soc-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/soc
From Santosh Shilimkar:
SOC updates for Keystone II devices:
- Clock tree support
- Clock management support using PM core
- Keystone config update for EMDA with ack from Vinod
- Enable SPI and I2C drivers
* tag 'keystone-soc-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone: (510 commits)
ARM: keystone: Enable I2C and SPI bus support
ARM: keystone: Select TI_EDMA to be able to enable SPI driver
dma: Allow TI_EDMA selectable for ARCH_KEYSTONE
ARM: dts: keystone: Add the SPI nodes
ARM: dts: keystone: Add i2c device nodes
ARM: keystone: add PM domain support for clock management
ARM: keystone: Enable clock drivers
ARM: dts: keystone: Add clock phandle to UART nodes
ARM: dts: keystone: Add clock tree data to devicetree
+Linux 3.12-rc4
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Haswell LynxPoint and LynxPoint-LP with the recent Intel BIOS show
mysterious wakeups after shutdown occasionally. After discussing with
BIOS engineers, they explained that the new BIOS expects that the
wakeup sources are cleared and set to D3 for all wakeup devices when
the system is going to sleep or power off, but the current xhci driver
doesn't do this properly (partly intentionally).
This patch introduces a new quirk, XHCI_SPURIOUS_WAKEUP, for
fixing the spurious wakeups at S5 by calling xhci_reset() in the xhci
shutdown ops as done in xhci_stop(), and setting the device to PCI D3
at shutdown and remove ops.
The PCI D3 call is based on the initial fix patch by Oliver Neukum.
[Note: Sarah changed the quirk name from XHCI_HSW_SPURIOUS_WAKEUP to
XHCI_SPURIOUS_WAKEUP, since none of the other quirks have system names
in them. Sarah also fixed a collision with a quirk submitted around the
same time, by changing the xhci->quirks bit from 17 to 18.]
This patch should be backported to kernels as old as 3.0, that
contain the commit 1c12443ab8 "xhci: Add
Lynx Point to list of Intel switchable hosts."
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The function pci_write_config_dword() sets the appropriate byteordering
internally so the value argument should not be converted to little-endian.
This bug was found by sparse.
This patch is not suitable for stable. Since cpu_to_lei32 is a no-op on
little endian systems, this bug would only affect big endian Intel
systems with the EHCI to xHCI port switchover, which are non-existent,
AFAIK.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
It has been reported that this chipset really cannot
sleep without this extraordinary delay.
This patch should be backported, in order to ensure this host functions
under stable kernels. The last quirk for Fresco Logic hosts (commit
bba18e33f2 "xhci: Extend Fresco Logic MSI
quirk.") was backported to stable kernels as old as 2.6.36.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The RWE bit of the USB 2.0 PORTPMSC register is supposed to enable
remote wakeup for devices in the lower power link state L1. It has
nothing to do with the device suspend remote wakeup from L2. The RWE
bit is designed to be set once (when USB 2.0 LPM is enabled for the
port) and cleared only when USB 2.0 LPM is disabled for the port.
The xHCI bus suspend method was setting the RWE bit erroneously, and the
bus resume method was clearing it. The xHCI 1.0 specification with
errata up to Aug 12, 2012 says in section 4.23.5.1.1.1 "Hardware
Controlled LPM":
"While Hardware USB2 LPM is enabled, software shall not modify the
HIRDBESL or RWE fields of the USB2 PORTPMSC register..."
If we have previously enabled USB 2.0 LPM for a device, that means when
the USB 2.0 bus is resumed, we violate the xHCI specification by
clearing RWE. It also means that after a bus resume, the host would
think remote wakeup is disabled from L1 for ports with USB 2.0 Link PM
enabled, which is not what we want.
This patch should be backported to kernels as old as 3.2, that
contain the commit 65580b4321 "xHCI: set
USB2 hardware LPM". That was the first kernel that supported USB 2.0
Link PM.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
In addition to the error statuses -ETIMEDOUT and -EPIPE, uhci_hub_control()
needs to return the length of copied buffer when appropriate, so that the
returned status of ->hub_control() in rh_call_control() in the USB core
HCD can be properly handled.
This patch also removes the OK() macro to make the code more readable.
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that UHCI IO registers have been defined in uhci-hcd.h, use them.
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-spear glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-spear suspend scenario.
Calling explicitly the ohci_suspend() routine in
spear_ohci_hcd_drv_suspend() will ensure proper
handling of suspend scenario.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-sm501 glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly
handle ohci-sm501 suspend scenario.
Calling explicitly the ohci_suspend() routine in
ohci_sm501_suspend() will ensure proper handling of suspend
scenario.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-pxa27x glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly
handle ohci-pxa27x suspend scenario.
Calling explicitly the ohci_suspend() routine in
ohci_hcd_pxa27x_drv_suspend() will ensure proper
handling of suspend scenario.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-platform glue was not
properly handled as it was not suspending generic part
of ohci controller.Alan Stern suggested, properly handle
ohci-platform suspend scenario.
Calling explicitly the ohci_suspend() routine in
ohci_platform_suspend() will ensure proper handling of
suspend scenario.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-omap glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-omap suspend scenario.
Calling explicitly the ohci_suspend() routine in
ohci_omap_suspend() will ensure proper handling of suspend
scenario.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-exynos glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-exynos suspend scenario.
Calling explicitly the ohci_suspend() routine in
exynos_ohci_suspend() will ensure proper handling of suspend
scenario.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-ep93xx glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-ep93xx suspend scenario.
Calling explicitly the ohci_suspend() routine in
ohci_hcd_ep93xx_drv_suspend() will ensure proper handling of
suspend scenario.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-da8xx glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-da8xx suspend scenario.
Calling explicitly the ohci_suspend()
routine in ohci_da8xx_suspend() will ensure proper
handling of suspend scenario.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-s3c2410 glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-s3c2410 suspend scenario.
Calling explicitly the ohci_suspend()
routine in ohci_hcd_s3c2410_drv_suspend() will ensure
proper handling of suspend scenario.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-at91 glue was not properly handled
as it was not suspending generic part of ohci controller. Alan Stern
suggested, properly handle ohci-at91 suspend scenario.
Calling explicitly the ohci_suspend() routine in ohci_hcd_at91_drv_suspend()
will ensure proper handling of suspend scenario. This task is sugested
by Alan Stern.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of OHCI was not properly
handled in ochi_suspend()routine. Alan Stern
suggested, properly handle OHCI suspend scenario.
This does generic proper handling of suspend
scenario to all OHCI SOC.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds an implementation for hwahc_op_get_frame_number. The
request is fulfulled by forwarding it to the lower hcd. This was done
because the GET_TIME request on the HWA requires sending an URB to the
HWA and waiting for the results which cannot be done in atomic context.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit "usb: pci-quirks: refactor AMD quirk to abstract AMD chipset types"
introduced a new AMD chipset type to filter AMD platforms with different
chipsets.
According to a recent thread [1], this patch updates SB800 prefetch routine
in AMD PLL quirk. And make it use the new chipset type to represent SB800
generation.
[1] http://marc.info/?l=linux-usb&m=138012321616452&w=2
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit "usb: pci-quirks: refactor AMD quirk to abstract AMD chipset types"
introduced a new AMD chipset type to filter AMD platforms with different
chipsets.
According to a recent thread [1], this patch updates USB subsystem hang
symptom quirk which is observed on AMD all SB600 and SB700 revision
0x3a/0x3b. And make it use the new chipset type to represent.
[1] http://marc.info/?l=linux-usb&m=138012321616452&w=2
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
