We shouldn't get here with RENAME_EXCHANGE set and no
target_ip, but let's be defensive, because xfs_cross_rename()
will dereference it.
Spotted by Coverity.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Incorrect NAPI polling caused WARNING at net/core/dev.c net_rx_action.
Some stability issues were also seen at high throughput and system
load before this patch.
This patch contains several changes in altera_tse_main.c:
- tse_rx() is fixed to not process more than `limit` frames
- tse_poll() is refactored to match NAPI logic
- only received frames are counted for return value
- removed bogus condition `(rxcomplete >= budget || txcomplete > 0)`
- replace by: if (rxcomplete < budget) -> call __napi_complete and enable irq
- altera_isr()
- replace spin_lock_irqsave() by spin_lock() - we are in isr
- use spinlocks just over irq manipulation, not over __napi_schedule
- reset IRQ first, then disable and schedule napi
This is a cleaned up resubmission from Vlastimil's recent submission.
Signed-off-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: Roman Pisl <rpisl@kky.zcu.cz>
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects a typo in the way tx_fifo_depth is read from the
devicetree. This patch was submitted by Vlastimil about a week ago,
and is now cleaned up and resubmitted.
Signed-off-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the default PM domain using PM_CLK is used for PM runtime, the real PM
domain(s) cannot be registered from DT later.
Hence do not enable it when running a multi-platform kernel with genpd
support on an r8a7740. The R-Mobile PM domain driver will take care of
PM runtime management of the module clocks.
The default PM domain is still needed for:
- platforms without genpd support,
- the legacy (non-DT) case, where genpd may take over later, except
for the C5 "always on" PM domain.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
With commit a7526eb5d0 (net: Unbreak compat_sys_{send,recv}msg), the
MSG_CMSG_COMPAT flag is blocked at the compat syscall entry points,
changing the kernel compat behaviour from the one before the commit it
was trying to fix (1be374a051, net: Block MSG_CMSG_COMPAT in
send(m)msg and recv(m)msg).
On 32-bit kernels (!CONFIG_COMPAT), MSG_CMSG_COMPAT is 0 and the native
32-bit sys_sendmsg() allows flag 0x80000000 to be set (it is ignored by
the kernel). However, on a 64-bit kernel, the compat ABI is different
with commit a7526eb5d0.
This patch changes the compat_sys_{send,recv}msg behaviour to the one
prior to commit 1be374a051.
The problem was found running 32-bit LTP (sendmsg01) binary on an arm64
kernel. Arguably, LTP should not pass 0xffffffff as flags to sendmsg()
but the general rule is not to break user ABI (even when the user
behaviour is not entirely sane).
Fixes: a7526eb5d0 (net: Unbreak compat_sys_{send,recv}msg)
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helper functions to access current->state.
Direct assignments are prone to races and therefore buggy.
current->state = TASK_RUNNING can be replaced by __set_current_state()
Thanks to Peter Zijlstra for the exact definition of the problem.
Suggested-By: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter's static checker pointed out:
net/sunrpc/xprtrdma/rpc_rdma.c:879 rpcrdma_reply_handler()
warn: can 'credits' be negative?
"credits" is defined as an int. The credits value comes from the
server as a 32-bit unsigned integer.
A malicious or broken server can plant a large unsigned integer in
that field which would result in an underflow in the following
logic, potentially triggering a deadlock of the mount point by
blocking the client from issuing more RPC requests.
net/sunrpc/xprtrdma/rpc_rdma.c:
876 credits = be32_to_cpu(headerp->rm_credit);
877 if (credits == 0)
878 credits = 1; /* don't deadlock */
879 else if (credits > r_xprt->rx_buf.rb_max_requests)
880 credits = r_xprt->rx_buf.rb_max_requests;
881
882 cwnd = xprt->cwnd;
883 xprt->cwnd = credits << RPC_CWNDSHIFT;
884 if (xprt->cwnd > cwnd)
885 xprt_release_rqst_cong(rqst->rq_task);
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: eba8ff660b ("xprtrdma: Move credit update to RPC . . .")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
This has been broken for a long time: it broke first in 2.6.35, then was
almost fixed in 2.6.36 but this one-liner slipped through the cracks.
The bug shows up as an infinite loop in Windows 7 (and newer) boot on
32-bit hosts without EPT.
Windows uses CMPXCHG8B to write to page tables, which causes a
page fault if running without EPT; the emulator is then called from
kvm_mmu_page_fault. The loop then happens if the higher 4 bytes are
not 0; the common case for this is that the NX bit (bit 63) is 1.
Fixes: 6550e1f165
Fixes: 16518d5ada
Cc: stable@vger.kernel.org # 2.6.35+
Reported-by: Erik Rull <erik.rull@rdsoftware.de>
Tested-by: Erik Rull <erik.rull@rdsoftware.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
'apic' is not defined if !CONFIG_X86_64 && !CONFIG_X86_LOCAL_APIC.
Posted interrupt makes no sense without CONFIG_SMP, and
CONFIG_X86_LOCAL_APIC will be set with it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch extends trace_kvm_exit() to include KVM exit reasons
(i.e. EC of HSR). The tracing function then dumps both exit reason
and PC of vCPU, shown as the following. Tracing tools can use this
new exit_reason field to better understand the behavior of guest VMs.
886.301252: kvm_exit: HSR_EC: 0x0024, PC: 0xfffffe0000506b28
Signed-off-by: Wei Huang <wei@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The check is supposed to catch page-unaligned sizes, not the inverse.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Currently following race is possible in team:
CPU0 CPU1
team_port_del
team_upper_dev_unlink
priv_flags &= ~IFF_TEAM_PORT
team_handle_frame
team_port_get_rcu
team_port_exists
priv_flags & IFF_TEAM_PORT == 0
return NULL (instead of port got
from rx_handler_data)
netdev_rx_handler_unregister
The thing is that the flag is removed before rx_handler is unregistered.
If team_handle_frame is called in between, team_port_exists returns 0
and team_port_get_rcu will return NULL.
So do not check the flag here. It is guaranteed by netdev_rx_handler_unregister
that team_handle_frame will always see valid rx_handler_data pointer.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Fixes: 3d249d4ca7 ("net: introduce ethernet teaming device")
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f2dba9c6ff ("rhashtable: Introduce rhashtable_walk_*") forgot to
initialize the members of struct rhashtable_walker after allocating it, which
caused an undefined value for 'resize' which is used later on.
Fixes: f2dba9c6ff ("rhashtable: Introduce rhashtable_walk_*")
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth 2015-02-23
Here's one important fix for the 4.0-rc series. Refactoring of Intel
Bluetooth controller detection ended up disabling some older ones which
are based on CSR hardware. This patch re-introduces the necessary USB id
and fixes the breakage.
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to define and use appropriate functions for when BLK_DEV_INTEGRITY
is not set.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Some dma channels may be reserved for other purpose in other layer,
like secure driver in EL2/EL3. PDMA driver can see the interrupt
status, but it should not try to handle related interrupt, since it
doesn't belong to PDMA driver in kernel. These interrupts should be
handled by corresponding client/module.Otherwise, it will overwrite
illegal memory and cause unexpected issues, since pdma driver only
requests resources for pdma channels.
In PDMA driver, the reserved channels are at the end of total 32
channels. If we find interrupt bit index is not smaller than total
dma channels, we should ignore it.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 1e02ce4ccc ("x86: Store a per-cpu shadow copy of CR4")
introduced CR4 shadows.
These shadows are initialized in early boot code. The commit missed
initialization for 64-bit PV(H) guests that this patch adds.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
A request in the ring buffer mustn't be read after it has been marked
as consumed. Otherwise it might already have been reused by the
frontend without violating the ring protocol.
To avoid inconsistencies in the backend only work on a private copy
of the request. This will ensure a malicious guest not being able to
bypass consistency checks of the backend by modifying an active
request.
Signed-off-by: Juergen Gross <jgross@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Hypercalls submitted by user space tools via the privcmd driver can
take a long time (potentially many 10s of seconds) if the hypercall
has many sub-operations.
A fully preemptible kernel may deschedule such as task in any upcall
called from a hypercall continuation.
However, in a kernel with voluntary or no preemption, hypercall
continuations in Xen allow event handlers to be run but the task
issuing the hypercall will not be descheduled until the hypercall is
complete and the ioctl returns to user space. These long running
tasks may also trigger the kernel's soft lockup detection.
Add xen_preemptible_hcall_begin() and xen_preemptible_hcall_end() to
bracket hypercalls that may be preempted. Use these in the privcmd
driver.
When returning from an upcall, call xen_maybe_preempt_hcall() which
adds a schedule point if if the current task was within a preemptible
hypercall.
Since _cond_resched() can move the task to a different CPU, clear and
set xen_in_preemptible_hcall around the call.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Commit d524165cb8 ("x86/apic: Check x2apic early") tests X2APIC_ENABLE
bit of MSR_IA32_APICBASE when CONFIG_X86_X2APIC is off and panics
the kernel when this bit is set.
Xen's PV guests will pass this MSR read to the hypervisor which will
return its version of the MSR, where this bit might be set. Make sure
we clear it before returning MSR value to the caller.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Commit eb10d63555 ("imx-drm: encoder prepare/mode_set must use adjusted mode")
broke the first LVDS modeset by using crtc->hwmode before crtc mode_set is
called. In fact, encoder prepare is not supposed to prepare the display clock
at all. Rather encoder mode_set should be used to set the DI clock rate, before
it is enabled by crtc commit.
Reported-by: Liu Ying <Ying.Liu@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The loop iterating over curr_ctrl in dw_hdmi terminates on mpixelclock == ~0UL,
so there needs to be an end of list element here in case a mode with a pixel
clock larger than 216 MHz is set.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This patch limits the pixel clock to 13.4 MHz - 266 MHz for i.MX6Q
and 13.5 MHz - 270 MHz for i.MX6DL, which is the range documented
in the HDMI Transmitter chapter of the respective reference manuals.
Without this patch, when connected to a monitor capable of 2160p60
modes, dw_hdmi will happily report this mode and the IPU code will
cause a division by zero in ipu_di_config_clock when trying to figure
out how to divide the 264 MHz HSP clock down to ~600 MHz.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Even if an unsupported mode with a pixel clock larger than two times the
264 MHz IPU HSP clock is set, don't divide by zero.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
When a PCM draining is performed to an empty stream that has been
already in PREPARED state, the current code just ignores and leaves as
it is, although the drain is supposed to set all such streams to SETUP
state. This patch covers that overlooked case.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The manual recommends that we reset the DSP when we suspend so add that in
runtime suspend handler
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The IPC driver saved only IMR register, we need to save the CSR as well, so
add it
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The updated firmware expects the MMX ID to be used as 3, so update the
driver as well
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "Extended Compat ID OS Feature Descriptor Specification" does not
require the (sub)compatible ids to be NUL-terminated, because they
are placed in a fixed-size buffer and only unused parts of it should
contain NULs. If the buffer is fully utilized, there is no place for NULs.
Consequently, the code which uses desc->ext_compat_id never expects the
data contained to be NUL terminated.
If the compatible id is stored after sub-compatible id, and the compatible
id is full length (8 bytes), the (useless) NUL terminator overwrites the
first byte of the sub-compatible id.
If the sub-compatible id is full length (8 bytes), the (useless) NUL
terminator ends up out of the buffer. The situation can happen in the RNDIS
function, where the buffer is a part of struct f_rndis_opts. The next
member of struct f_rndis_opts is a mutex, so its first byte gets
overwritten. The said byte is a part of a mutex'es member which contains
the information on whether the muext is locked or not. This can lead to a
deadlock, because, in a configfs-composed gadget when a function is linked
into a configuration with config_usb_cfg_link(), usb_get_function()
is called, which then calls rndis_alloc(), which tries locking the same
mutex and (wrongly) finds it already locked.
This patch eliminates NUL terminating of the (sub)compatible id.
Cc: <stable@vger.kernel.org> # v3.16+
Fixes: da4243145f: "usb: gadget: configfs: OS Extended Compatibility descriptors support"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In the wrapper the IRQ disable should be done by writing 1's to the
IRQ*_CLR register. Existing code is broken because it instead writes
zeros to IRQ*_SET register.
Fix this by adding functions dwc3_omap_write_irqmisc_clr() and
dwc3_omap_write_irq0_clr() which do the right thing.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
uvc_v4l2.c:264:29: warning: symbol 'uvc_v4l2_ioctl_ops' was not declared. Should it be static?
uvc_v4l2.c:355:29: warning: symbol 'uvc_v4l2_fops' was not declared. Should it be static?
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
g_ffs.c:136:3: warning: symbol 'gfs_configurations' was not declared. Should it be static?
g_ffs.c:281:16: warning: Using plain integer as NULL pointer
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
uvc_video.c:283:5: warning: symbol 'uvcg_video_pump' was not declared. Should it be static?
uvc_video.c:342:5: warning: symbol 'uvcg_video_enable' was not declared. Should it be static?
uvc_video.c:381:5: warning: symbol 'uvcg_video_init' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
f_sourcesink.c:347:34: warning: symbol 'ss_int_source_comp_desc' was not declared. Should it be static?
f_sourcesink.c:365:34: warning: symbol 'ss_int_sink_comp_desc' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
f_uac2.c:57:12: warning: symbol 'uac2_name' was not declared. Should it be static?
f_uac2.c:637:36: warning: symbol 'in_clk_src_desc' was not declared. Should it be static?
f_uac2.c:649:36: warning: symbol 'out_clk_src_desc' was not declared. Should it be static?
f_uac2.c:661:39: warning: symbol 'usb_out_it_desc' was not declared. Should it be static?
f_uac2.c:675:39: warning: symbol 'io_in_it_desc' was not declared. Should it be static?
f_uac2.c:689:40: warning: symbol 'usb_in_ot_desc' was not declared. Should it be static?
f_uac2.c:703:40: warning: symbol 'io_out_ot_desc' was not declared. Should it be static?
f_uac2.c:716:34: warning: symbol 'ac_hdr_desc' was not declared. Should it be static?
f_uac2.c:754:34: warning: symbol 'as_out_hdr_desc' was not declared. Should it be static?
f_uac2.c:767:38: warning: symbol 'as_out_fmt1_desc' was not declared. Should it be static?
f_uac2.c:775:32: warning: symbol 'fs_epout_desc' was not declared. Should it be static?
f_uac2.c:785:32: warning: symbol 'hs_epout_desc' was not declared. Should it be static?
f_uac2.c:831:34: warning: symbol 'as_in_hdr_desc' was not declared. Should it be static?
f_uac2.c:844:38: warning: symbol 'as_in_fmt1_desc' was not declared. Should it be static?
f_uac2.c:852:32: warning: symbol 'fs_epin_desc' was not declared. Should it be static?
f_uac2.c:862:32: warning: symbol 'hs_epin_desc' was not declared. Should it be static?
f_uac2.c:1566:21: warning: symbol 'afunc_alloc' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warning:
f_hid.c:572:30: warning: symbol 'f_hidg_fops' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We still have a combination of legacy phys and generic phys in
use so we need to support both types of phy for musb_dsps.c.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The renesas usbhs driver calls extcon_get_edev_by_phandle(), which
is defined in drivers/extcon/extcon-class.c, and that can be a
loadable module. If the extcon-class support is disabled, usbhs
will work correctly for all devices that do not need extcon.
However, if extcon-class is a loadable module, and usbhs is
built-in, the kernel fails to link. In order to solve that,
we need a Kconfig dependency that allows extcon to be disabled
but does not allow usbhs built-in if extcon is a module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The value for the multipoint dts property is ignored when parsing with
of_property_read_bool, so we currently have multipoint always set as 1
even if value 0 is specified in the dts file.
Let's fix this to read the value too instead of just the property like
the binding documentation says as otherwise MUSB will fail to work
on devices with Mentor configuration that does not support multipoint.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The gpio_chip operations receive a pointer the gpio_chip struct which is
contained in the driver's private struct, yet the container_of call in those
functions point to the mfd struct defined in include/linux/mfd/tps65912.h.
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The change:
7b8792bbdf
gpiolib: of: Correct error handling in of_get_named_gpiod_flags
assumed that only one gpio-chip is registred per of-node.
Some drivers register more than one chip per of-node, so
adjust the matching function of_gpiochip_find_and_xlate to
not stop looking for chips if a node-match is found and
the translation fails.
Cc: Stable <stable@vger.kernel.org>
Fixes: 7b8792bbdf ("gpiolib: of: Correct error handling in of_get_named_gpiod_flags")
Signed-off-by: Hans Holmberg <hans.holmberg@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Tyler Hall <tylerwhall@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Microsoft Natural Wireless Ergonomic Keyboard 7000 has special My
Favorites 1..5 keys which are handled through a vendor-defined usage
page (0xff05).
Apply MS_ERGONOMY quirks handling to USB PID 0x071d (Microsoft Microsoft
2.4GHz Transceiver V1.0) so that the My Favorites 1..5 keys are reported
as KEY_F14..18 events.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=52841
Signed-off-by: Jakub Sitnicki <jsitnicki@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
d1c7e29e8d (HID: i2c-hid: prevent buffer overflow in early IRQ)
changed hid_get_input() to read ihid->bufsize bytes, which can be
more than wMaxInputLength. This is the case with the Dell XPS 13
9343, and it is causing events to be missed. In some cases the
missed events are releases, which can cause the cursor to jump or
freeze, among other problems. Limit the number of bytes read to
min(wMaxInputLength, ihid->bufsize) to prevent such problems.
Fixes: d1c7e29e8d "HID: i2c-hid: prevent buffer overflow in early IRQ"
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
skylake_update_primary_plane() did not handle all pixel formats returned
by skl_format_to_fourcc(). Handle alpha similar to skl_update_plane().
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89052
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
