* tmp-917a9:
ARM/vdso: Mark the vDSO code read-only after init
x86/vdso: Mark the vDSO code read-only after init
lkdtm: Verify that '__ro_after_init' works correctly
arch: Introduce post-init read-only memory
x86/mm: Always enable CONFIG_DEBUG_RODATA and remove the Kconfig option
mm/init: Add 'rodata=off' boot cmdline parameter to disable read-only kernel mappings
asm-generic: Consolidate mark_rodata_ro()
Linux 4.4.6
ld-version: Fix awk regex compile failure
target: Drop incorrect ABORT_TASK put for completed commands
block: don't optimize for non-cloned bio in bio_get_last_bvec()
MIPS: smp.c: Fix uninitialised temp_foreign_map
MIPS: Fix build error when SMP is used without GIC
ovl: fix getcwd() failure after unsuccessful rmdir
ovl: copy new uid/gid into overlayfs runtime inode
userfaultfd: don't block on the last VM updates at exit time
powerpc/powernv: Fix OPAL_CONSOLE_FLUSH prototype and usages
powerpc/powernv: Add a kmsg_dumper that flushes console output on panic
powerpc: Fix dedotify for binutils >= 2.26
Revert "drm/radeon/pm: adjust display configuration after powerstate"
drm/radeon: Fix error handling in radeon_flip_work_func.
drm/amdgpu: Fix error handling in amdgpu_flip_work_func.
Revert "drm/radeon: call hpd_irq_event on resume"
x86/mm: Fix slow_virt_to_phys() for X86_PAE again
gpu: ipu-v3: Do not bail out on missing optional port nodes
mac80211: Fix Public Action frame RX in AP mode
mac80211: check PN correctly for GCMP-encrypted fragmented MPDUs
mac80211: minstrel_ht: fix a logic error in RTS/CTS handling
mac80211: minstrel_ht: set default tx aggregation timeout to 0
mac80211: fix use of uninitialised values in RX aggregation
mac80211: minstrel: Change expected throughput unit back to Kbps
iwlwifi: mvm: inc pending frames counter also when txing non-sta
can: gs_usb: fixed disconnect bug by removing erroneous use of kfree()
cfg80211/wext: fix message ordering
wext: fix message delay/ordering
ovl: fix working on distributed fs as lower layer
ovl: ignore lower entries when checking purity of non-directory entries
ASoC: wm8958: Fix enum ctl accesses in a wrong type
ASoC: wm8994: Fix enum ctl accesses in a wrong type
ASoC: samsung: Use IRQ safe spin lock calls
ASoC: dapm: Fix ctl value accesses in a wrong type
ncpfs: fix a braino in OOM handling in ncp_fill_cache()
jffs2: reduce the breakage on recovery from halfway failed rename()
dmaengine: at_xdmac: fix residue computation
tracing: Fix check for cpu online when event is disabled
s390/dasd: fix diag 0x250 inline assembly
s390/mm: four page table levels vs. fork
KVM: MMU: fix reserved bit check for ept=0/CR0.WP=0/CR4.SMEP=1/EFER.NX=0
KVM: MMU: fix ept=0/pte.u=1/pte.w=0/CR0.WP=0/CR4.SMEP=1/EFER.NX=0 combo
KVM: PPC: Book3S HV: Sanitize special-purpose register values on guest exit
KVM: s390: correct fprs on SIGP (STOP AND) STORE STATUS
KVM: VMX: disable PEBS before a guest entry
kvm: cap halt polling at exactly halt_poll_ns
PCI: Allow a NULL "parent" pointer in pci_bus_assign_domain_nr()
ARM: OMAP2+: hwmod: Introduce ti,no-idle dt property
ARM: dts: dra7: do not gate cpsw clock due to errata i877
ARM: mvebu: fix overlap of Crypto SRAM with PCIe memory window
arm64: account for sparsemem section alignment when choosing vmemmap offset
Linux 4.4.5
drm/amdgpu: fix topaz/tonga gmc assignment in 4.4 stable
modules: fix longstanding /proc/kallsyms vs module insertion race.
drm/i915: refine qemu south bridge detection
drm/i915: more virtual south bridge detection
block: get the 1st and last bvec via helpers
block: check virt boundary in bio_will_gap()
drm/amdgpu: Use drm_calloc_large for VM page_tables array
thermal: cpu_cooling: fix out of bounds access in time_in_idle
i2c: brcmstb: allocate correct amount of memory for regmap
ubi: Fix out of bounds write in volume update code
cxl: Fix PSL timebase synchronization detection
MIPS: traps: Fix SIGFPE information leak from `do_ov' and `do_trap_or_bp'
MIPS: scache: Fix scache init with invalid line size.
USB: serial: option: add support for Quectel UC20
USB: serial: option: add support for Telit LE922 PID 0x1045
USB: qcserial: add Sierra Wireless EM74xx device ID
USB: qcserial: add Dell Wireless 5809e Gobi 4G HSPA+ (rev3)
USB: cp210x: Add ID for Parrot NMEA GPS Flight Recorder
usb: chipidea: otg: change workqueue ci_otg as freezable
ALSA: timer: Fix broken compat timer user status ioctl
ALSA: hdspm: Fix zero-division
ALSA: hdsp: Fix wrong boolean ctl value accesses
ALSA: hdspm: Fix wrong boolean ctl value accesses
ALSA: seq: oss: Don't drain at closing a client
ALSA: pcm: Fix ioctls for X32 ABI
ALSA: timer: Fix ioctls for X32 ABI
ALSA: rawmidi: Fix ioctls X32 ABI
ALSA: hda - Fix mic issues on Acer Aspire E1-472
ALSA: ctl: Fix ioctls for X32 ABI
ALSA: usb-audio: Add a quirk for Plantronics DA45
adv7604: fix tx 5v detect regression
dmaengine: pxa_dma: fix cyclic transfers
Fix directory hardlinks from deleted directories
jffs2: Fix page lock / f->sem deadlock
Revert "jffs2: Fix lock acquisition order bug in jffs2_write_begin"
Btrfs: fix loading of orphan roots leading to BUG_ON
pata-rb532-cf: get rid of the irq_to_gpio() call
tracing: Do not have 'comm' filter override event 'comm' field
ata: ahci: don't mark HotPlugCapable Ports as external/removable
PM / sleep / x86: Fix crash on graph trace through x86 suspend
arm64: vmemmap: use virtual projection of linear region
Adding Intel Lewisburg device IDs for SATA
writeback: flush inode cgroup wb switches instead of pinning super_block
block: bio: introduce helpers to get the 1st and last bvec
libata: Align ata_device's id on a cacheline
libata: fix HDIO_GET_32BIT ioctl
drm/amdgpu: return from atombios_dp_get_dpcd only when error
drm/amdgpu/gfx8: specify which engine to wait before vm flush
drm/amdgpu: apply gfx_v8 fixes to gfx_v7 as well
drm/amdgpu/pm: update current crtc info after setting the powerstate
drm/radeon/pm: update current crtc info after setting the powerstate
drm/ast: Fix incorrect register check for DRAM width
target: Fix WRITE_SAME/DISCARD conversion to linux 512b sectors
iommu/vt-d: Use BUS_NOTIFY_REMOVED_DEVICE in hotplug path
iommu/amd: Fix boot warning when device 00:00.0 is not iommu covered
iommu/amd: Apply workaround for ATS write permission check
arm/arm64: KVM: Fix ioctl error handling
KVM: x86: fix root cause for missed hardware breakpoints
vfio: fix ioctl error handling
Fix cifs_uniqueid_to_ino_t() function for s390x
CIFS: Fix SMB2+ interim response processing for read requests
cifs: fix out-of-bounds access in lease parsing
fbcon: set a default value to blink interval
kvm: x86: Update tsc multiplier on change.
mips/kvm: fix ioctl error handling
parisc: Fix ptrace syscall number and return value modification
PCI: keystone: Fix MSI code that retrieves struct pcie_port pointer
block: Initialize max_dev_sectors to 0
drm/amdgpu: mask out WC from BO on unsupported arches
btrfs: async-thread: Fix a use-after-free error for trace
btrfs: Fix no_space in write and rm loop
Btrfs: fix deadlock running delayed iputs at transaction commit time
drivers: sh: Restore legacy clock domain on SuperH platforms
use ->d_seq to get coherency between ->d_inode and ->d_flags
Linux 4.4.4
iwlwifi: mvm: don't allow sched scans without matches to be started
iwlwifi: update and fix 7265 series PCI IDs
iwlwifi: pcie: properly configure the debug buffer size for 8000
iwlwifi: dvm: fix WoWLAN
security: let security modules use PTRACE_MODE_* with bitmasks
IB/cma: Fix RDMA port validation for iWarp
x86/irq: Plug vector cleanup race
x86/irq: Call irq_force_move_complete with irq descriptor
x86/irq: Remove outgoing CPU from vector cleanup mask
x86/irq: Remove the cpumask allocation from send_cleanup_vector()
x86/irq: Clear move_in_progress before sending cleanup IPI
x86/irq: Remove offline cpus from vector cleanup
x86/irq: Get rid of code duplication
x86/irq: Copy vectormask instead of an AND operation
x86/irq: Check vector allocation early
x86/irq: Reorganize the search in assign_irq_vector
x86/irq: Reorganize the return path in assign_irq_vector
x86/irq: Do not use apic_chip_data.old_domain as temporary buffer
x86/irq: Validate that irq descriptor is still active
x86/irq: Fix a race in x86_vector_free_irqs()
x86/irq: Call chip->irq_set_affinity in proper context
x86/entry/compat: Add missing CLAC to entry_INT80_32
x86/mpx: Fix off-by-one comparison with nr_registers
hpfs: don't truncate the file when delete fails
do_last(): ELOOP failure exit should be done after leaving RCU mode
should_follow_link(): validate ->d_seq after having decided to follow
xen/pcifront: Fix mysterious crashes when NUMA locality information was extracted.
xen/pciback: Save the number of MSI-X entries to be copied later.
xen/pciback: Check PF instead of VF for PCI_COMMAND_MEMORY
xen/scsiback: correct frontend counting
xen/arm: correctly handle DMA mapping of compound pages
ARM: at91/dt: fix typo in sama5d2 pinmux descriptions
ARM: OMAP2+: Fix onenand initialization to avoid filesystem corruption
do_last(): don't let a bogus return value from ->open() et.al. to confuse us
kernel/resource.c: fix muxed resource handling in __request_region()
sunrpc/cache: fix off-by-one in qword_get()
tracing: Fix showing function event in available_events
powerpc/eeh: Fix partial hotplug criterion
KVM: x86: MMU: fix ubsan index-out-of-range warning
KVM: x86: fix conversion of addresses to linear in 32-bit protected mode
KVM: x86: fix missed hardware breakpoints
KVM: arm/arm64: vgic: Ensure bitmaps are long enough
KVM: async_pf: do not warn on page allocation failures
of/irq: Fix msi-map calculation for nonzero rid-base
NFSv4: Fix a dentry leak on alias use
nfs: fix nfs_size_to_loff_t
block: fix use-after-free in dio_bio_complete
bio: return EINTR if copying to user space got interrupted
i2c: i801: Adding Intel Lewisburg support for iTCO
phy: core: fix wrong err handle for phy_power_on
writeback: keep superblock pinned during cgroup writeback association switches
cgroup: make sure a parent css isn't offlined before its children
cpuset: make mm migration asynchronous
PCI/AER: Flush workqueue on device remove to avoid use-after-free
ARCv2: SMP: Emulate IPI to self using software triggered interrupt
ARCv2: STAR 9000950267: Handle return from intr to Delay Slot #2
libata: fix sff host state machine locking while polling
qla2xxx: Fix stale pointer access.
spi: atmel: fix gpio chip-select in case of non-DT platform
target: Fix race with SCF_SEND_DELAYED_TAS handling
target: Fix remote-port TMR ABORT + se_cmd fabric stop
target: Fix TAS handling for multi-session se_node_acls
target: Fix LUN_RESET active TMR descriptor handling
target: Fix LUN_RESET active I/O handling for ACK_KREF
ALSA: hda - Fixing background noise on Dell Inspiron 3162
ALSA: hda - Apply clock gate workaround to Skylake, too
Revert "workqueue: make sure delayed work run in local cpu"
workqueue: handle NUMA_NO_NODE for unbound pool_workqueue lookup
mac80211: Requeue work after scan complete for all VIF types.
rfkill: fix rfkill_fop_read wait_event usage
tick/nohz: Set the correct expiry when switching to nohz/lowres mode
perf stat: Do not clean event's private stats
cdc-acm:exclude Samsung phone 04e8:685d
Revert "Staging: panel: usleep_range is preferred over udelay"
Staging: speakup: Fix getting port information
sd: Optimal I/O size is in bytes, not sectors
libceph: don't spam dmesg with stray reply warnings
libceph: use the right footer size when skipping a message
libceph: don't bail early from try_read() when skipping a message
libceph: fix ceph_msg_revoke()
seccomp: always propagate NO_NEW_PRIVS on tsync
cpufreq: Fix NULL reference crash while accessing policy->governor_data
cpufreq: pxa2xx: fix pxa_cpufreq_change_voltage prototype
hwmon: (ads1015) Handle negative conversion values correctly
hwmon: (gpio-fan) Remove un-necessary speed_index lookup for thermal hook
hwmon: (dell-smm) Blacklist Dell Studio XPS 8000
Thermal: do thermal zone update after a cooling device registered
Thermal: handle thermal zone device properly during system sleep
Thermal: initialize thermal zone device correctly
IB/mlx5: Expose correct maximum number of CQE capacity
IB/qib: Support creating qps with GFP_NOIO flag
IB/qib: fix mcast detach when qp not attached
IB/cm: Fix a recently introduced deadlock
dmaengine: dw: disable BLOCK IRQs for non-cyclic xfer
dmaengine: at_xdmac: fix resume for cyclic transfers
dmaengine: dw: fix cyclic transfer callbacks
dmaengine: dw: fix cyclic transfer setup
nfit: fix multi-interface dimm handling, acpi6.1 compatibility
ACPI / PCI / hotplug: unlock in error path in acpiphp_enable_slot()
ACPI: Revert "ACPI / video: Add Dell Inspiron 5737 to the blacklist"
ACPI / video: Add disable_backlight_sysfs_if quirk for the Toshiba Satellite R830
ACPI / video: Add disable_backlight_sysfs_if quirk for the Toshiba Portege R700
lib: sw842: select crc32
uapi: update install list after nvme.h rename
ideapad-laptop: Add Lenovo Yoga 700 to no_hw_rfkill dmi list
ideapad-laptop: Add Lenovo ideapad Y700-17ISK to no_hw_rfkill dmi list
toshiba_acpi: Fix blank screen at boot if transflective backlight is supported
make sure that freeing shmem fast symlinks is RCU-delayed
drm/radeon/pm: adjust display configuration after powerstate
drm/radeon: Don't hang in radeon_flip_work_func on disabled crtc. (v2)
drm: Fix treatment of drm_vblank_offdelay in drm_vblank_on() (v2)
drm: Fix drm_vblank_pre/post_modeset regression from Linux 4.4
drm: Prevent vblank counter bumps > 1 with active vblank clients. (v2)
drm: No-Op redundant calls to drm_vblank_off() (v2)
drm/radeon: use post-decrement in error handling
drm/qxl: use kmalloc_array to alloc reloc_info in qxl_process_single_command
drm/i915: fix error path in intel_setup_gmbus()
drm/i915/dsi: don't pass arbitrary data to sideband
drm/i915/dsi: defend gpio table against out of bounds access
drm/i915/skl: Don't skip mst encoders in skl_ddi_pll_select()
drm/i915: Don't reject primary plane windowing with color keying enabled on SKL+
drm/i915/dp: fall back to 18 bpp when sink capability is unknown
drm/i915: Make sure DC writes are coherent on flush.
drm/i915: Init power domains early in driver load
drm/i915: intel_hpd_init(): Fix suspend/resume reprobing
drm/i915: Restore inhibiting the load of the default context
drm: fix missing reference counting decrease
drm/radeon: hold reference to fences in radeon_sa_bo_new
drm/radeon: mask out WC from BO on unsupported arches
drm: add helper to check for wc memory support
drm/radeon: fix DP audio support for APU with DCE4.1 display engine
drm/radeon: Add a common function for DFS handling
drm/radeon: cleaned up VCO output settings for DP audio
drm/radeon: properly byte swap vce firmware setup
drm/radeon: clean up fujitsu quirks
drm/radeon: Fix "slow" audio over DP on DCE8+
drm/radeon: call hpd_irq_event on resume
drm/radeon: Fix off-by-one errors in radeon_vm_bo_set_addr
drm/dp/mst: deallocate payload on port destruction
drm/dp/mst: Reverse order of MST enable and clearing VC payload table.
drm/dp/mst: move GUID storage from mgr, port to only mst branch
drm/dp/mst: Calculate MST PBN with 31.32 fixed point
drm: Add drm_fixp_from_fraction and drm_fixp2int_ceil
drm/dp/mst: fix in RAD element access
drm/dp/mst: fix in MSTB RAD initialization
drm/dp/mst: always send reply for UP request
drm/dp/mst: process broadcast messages correctly
drm/nouveau: platform: Fix deferred probe
drm/nouveau/disp/dp: ensure sink is powered up before attempting link training
drm/nouveau/display: Enable vblank irqs after display engine is on again.
drm/nouveau/kms: take mode_config mutex in connector hotplug path
drm/amdgpu/pm: adjust display configuration after powerstate
drm/amdgpu: Don't hang in amdgpu_flip_work_func on disabled crtc.
drm/amdgpu: use post-decrement in error handling
drm/amdgpu: fix issue with overlapping userptrs
drm/amdgpu: hold reference to fences in amdgpu_sa_bo_new (v2)
drm/amdgpu: remove unnecessary forward declaration
drm/amdgpu: fix s4 resume
drm/amdgpu: remove exp hardware support from iceland
drm/amdgpu: don't load MEC2 on topaz
drm/amdgpu: drop topaz support from gmc8 module
drm/amdgpu: pull topaz gmc bits into gmc_v7
drm/amdgpu: The VI specific EXE bit should only apply to GMC v8.0 above
drm/amdgpu: iceland use CI based MC IP
drm/amdgpu: move gmc7 support out of CIK dependency
drm/amdgpu: no need to load MC firmware on fiji
drm/amdgpu: fix amdgpu_bo_pin_restricted VRAM placing v2
drm/amdgpu: fix tonga smu resume
drm/amdgpu: fix lost sync_to if scheduler is enabled.
drm/amdgpu: call hpd_irq_event on resume
drm/amdgpu: Fix off-by-one errors in amdgpu_vm_bo_map
drm/vmwgfx: respect 'nomodeset'
drm/vmwgfx: Fix a width / pitch mismatch on framebuffer updates
drm/vmwgfx: Fix an incorrect lock check
virtio_pci: fix use after free on release
virtio_balloon: fix race between migration and ballooning
virtio_balloon: fix race by fill and leak
regulator: mt6311: MT6311_REGULATOR needs to select REGMAP_I2C
regulator: axp20x: Fix GPIO LDO enable value for AXP22x
clk: exynos: use irqsave version of spin_lock to avoid deadlock with irqs
cxl: use correct operator when writing pcie config space values
sparc64: fix incorrect sign extension in sys_sparc64_personality
EDAC, mc_sysfs: Fix freeing bus' name
EDAC: Robustify workqueues destruction
MIPS: Fix buffer overflow in syscall_get_arguments()
MIPS: Fix some missing CONFIG_CPU_MIPSR6 #ifdefs
MIPS: hpet: Choose a safe value for the ETIME check
MIPS: Loongson-3: Fix SMP_ASK_C0COUNT IPI handler
Revert "MIPS: Fix PAGE_MASK definition"
cputime: Prevent 32bit overflow in time[val|spec]_to_cputime()
time: Avoid signed overflow in timekeeping_get_ns()
Bluetooth: 6lowpan: Fix handling of uncompressed IPv6 packets
Bluetooth: 6lowpan: Fix kernel NULL pointer dereferences
Bluetooth: Fix incorrect removing of IRKs
Bluetooth: Add support of Toshiba Broadcom based devices
Bluetooth: Use continuous scanning when creating LE connections
Drivers: hv: vmbus: Fix a Host signaling bug
tools: hv: vss: fix the write()'s argument: error -> vss_msg
mmc: sdhci: Allow override of get_cd() called from sdhci_request()
mmc: sdhci: Allow override of mmc host operations
mmc: sdhci-pci: Fix card detect race for Intel BXT/APL
mmc: pxamci: fix again read-only gpio detection polarity
mmc: sdhci-acpi: Fix card detect race for Intel BXT/APL
mmc: mmci: fix an ages old detection error
mmc: core: Enable tuning according to the actual timing
mmc: sdhci: Fix sdhci_runtime_pm_bus_on/off()
mmc: mmc: Fix incorrect use of driver strength switching HS200 and HS400
mmc: sdio: Fix invalid vdd in voltage switch power cycle
mmc: sdhci: Fix DMA descriptor with zero data length
mmc: sdhci-pci: Do not default to 33 Ohm driver strength for Intel SPT
mmc: usdhi6rol0: handle NULL data in timeout
clockevents/tcb_clksrc: Prevent disabling an already disabled clock
posix-clock: Fix return code on the poll method's error path
irqchip/gic-v3-its: Fix double ICC_EOIR write for LPI in EOImode==1
irqchip/atmel-aic: Fix wrong bit operation for IRQ priority
irqchip/mxs: Add missing set_handle_irq()
irqchip/omap-intc: Add support for spurious irq handling
coresight: checking for NULL string in coresight_name_match()
dm: fix dm_rq_target_io leak on faults with .request_fn DM w/ blk-mq paths
dm snapshot: fix hung bios when copy error occurs
dm space map metadata: remove unused variable in brb_pop()
tda1004x: only update the frontend properties if locked
vb2: fix a regression in poll() behavior for output,streams
gspca: ov534/topro: prevent a division by 0
si2157: return -EINVAL if firmware blob is too big
media: dvb-core: Don't force CAN_INVERSION_AUTO in oneshot mode
rc: sunxi-cir: Initialize the spinlock properly
namei: ->d_inode of a pinned dentry is stable only for positives
mei: validate request value in client notify request ioctl
mei: fix fasync return value on error
rtlwifi: rtl8723be: Fix module parameter initialization
rtlwifi: rtl8188ee: Fix module parameter initialization
rtlwifi: rtl8192se: Fix module parameter initialization
rtlwifi: rtl8723ae: Fix initialization of module parameters
rtlwifi: rtl8192de: Fix incorrect module parameter descriptions
rtlwifi: rtl8192ce: Fix handling of module parameters
rtlwifi: rtl8192cu: Add missing parameter setup
rtlwifi: rtl_pci: Fix kernel panic
locks: fix unlock when fcntl_setlk races with a close
um: link with -lpthread
uml: fix hostfs mknod()
uml: flush stdout before forking
s390/fpu: signals vs. floating point control register
s390/compat: correct restore of high gprs on signal return
s390/dasd: fix performance drop
s390/dasd: fix refcount for PAV reassignment
s390/dasd: prevent incorrect length error under z/VM after PAV changes
s390: fix normalization bug in exception table sorting
btrfs: initialize the seq counter in struct btrfs_device
Btrfs: Initialize btrfs_root->highest_objectid when loading tree root and subvolume roots
Btrfs: fix transaction handle leak on failure to create hard link
Btrfs: fix number of transaction units required to create symlink
Btrfs: send, don't BUG_ON() when an empty symlink is found
btrfs: statfs: report zero available if metadata are exhausted
Btrfs: igrab inode in writepage
Btrfs: add missing brelse when superblock checksum fails
KVM: s390: fix memory overwrites when vx is disabled
s390/kvm: remove dependency on struct save_area definition
clocksource/drivers/vt8500: Increase the minimum delta
genirq: Validate action before dereferencing it in handle_irq_event_percpu()
mm: numa: quickly fail allocations for NUMA balancing on full nodes
mm: thp: fix SMP race condition between THP page fault and MADV_DONTNEED
ocfs2: unlock inode if deleting inode from orphan fails
drm/i915: shut up gen8+ SDE irq dmesg noise
iw_cxgb3: Fix incorrectly returning error on success
spi: omap2-mcspi: Prevent duplicate gpio_request
drivers: android: correct the size of struct binder_uintptr_t for BC_DEAD_BINDER_DONE
USB: option: add "4G LTE usb-modem U901"
USB: option: add support for SIM7100E
USB: cp210x: add IDs for GE B650V3 and B850V3 boards
usb: dwc3: Fix assignment of EP transfer resources
can: ems_usb: Fix possible tx overflow
dm thin: fix race condition when destroying thin pool workqueue
bcache: Change refill_dirty() to always scan entire disk if necessary
bcache: prevent crash on changing writeback_running
bcache: allows use of register in udev to avoid "device_busy" error.
bcache: unregister reboot notifier if bcache fails to unregister device
bcache: fix a leak in bch_cached_dev_run()
bcache: clear BCACHE_DEV_UNLINK_DONE flag when attaching a backing device
bcache: Add a cond_resched() call to gc
bcache: fix a livelock when we cause a huge number of cache misses
lib/ucs2_string: Correct ucs2 -> utf8 conversion
efi: Add pstore variables to the deletion whitelist
efi: Make efivarfs entries immutable by default
efi: Make our variable validation list include the guid
efi: Do variable name validation tests in utf8
efi: Use ucs2_as_utf8 in efivarfs instead of open coding a bad version
lib/ucs2_string: Add ucs2 -> utf8 helper functions
ARM: 8457/1: psci-smp is built only for SMP
drm/gma500: Use correct unref in the gem bo create function
devm_memremap: Fix error value when memremap failed
KVM: s390: fix guest fprs memory leak
arm64: errata: Add -mpc-relative-literal-loads to build flags
ARM: debug-ll: fix BCM63xx entry for multiplatform
ext4: fix bh->b_state corruption
sctp: Fix port hash table size computation
unix_diag: fix incorrect sign extension in unix_lookup_by_ino
tipc: unlock in error path
rtnl: RTM_GETNETCONF: fix wrong return value
IFF_NO_QUEUE: Fix for drivers not calling ether_setup()
tcp/dccp: fix another race at listener dismantle
route: check and remove route cache when we get route
net_sched fix: reclassification needs to consider ether protocol changes
pppoe: fix reference counting in PPPoE proxy
l2tp: Fix error creating L2TP tunnels
net/mlx4_en: Avoid changing dev->features directly in run-time
net/mlx4_en: Choose time-stamping shift value according to HW frequency
net/mlx4_en: Count HW buffer overrun only once
qmi_wwan: add "4G LTE usb-modem U901"
tcp: md5: release request socket instead of listener
tipc: fix premature addition of node to lookup table
af_unix: Guard against other == sk in unix_dgram_sendmsg
af_unix: Don't set err in unix_stream_read_generic unless there was an error
ipv4: fix memory leaks in ip_cmsg_send() callers
bonding: Fix ARP monitor validation
bpf: fix branch offset adjustment on backjumps after patching ctx expansion
flow_dissector: Fix unaligned access in __skb_flow_dissector when used by eth_get_headlen
net: Copy inner L3 and L4 headers as unaligned on GRE TEB
sctp: translate network order to host order when users get a hmacid
enic: increment devcmd2 result ring in case of timeout
tg3: Fix for tg3 transmit queue 0 timed out when too many gso_segs
net:Add sysctl_max_skb_frags
tcp: do not drop syn_recv on all icmp reports
unix: correctly track in-flight fds in sending process user_struct
ipv6: fix a lockdep splat
ipv6: addrconf: Fix recursive spin lock call
ipv6/udp: use sticky pktinfo egress ifindex on connect()
ipv6: enforce flowi6_oif usage in ip6_dst_lookup_tail()
tcp: beware of alignments in tcp_get_info()
switchdev: Require RTNL mutex to be held when sending FDB notifications
inet: frag: Always orphan skbs inside ip_defrag()
tipc: fix connection abort during subscription cancel
net: dsa: fix mv88e6xxx switches
sctp: allow setting SCTP_SACK_IMMEDIATELY by the application
pptp: fix illegal memory access caused by multiple bind()s
af_unix: fix struct pid memory leak
tcp: fix NULL deref in tcp_v4_send_ack()
lwt: fix rx checksum setting for lwt devices tunneling over ipv6
tunnels: Allow IPv6 UDP checksums to be correctly controlled.
net: dp83640: Fix tx timestamp overflow handling.
gro: Make GRO aware of lightweight tunnels.
af_iucv: Validate socket address length in iucv_sock_bind()
Conflicts:
arch/arm64/Makefile
arch/arm64/include/asm/cacheflush.h
drivers/mmc/host/sdhci.c
drivers/usb/dwc3/ep0.c
drivers/usb/dwc3/gadget.c
kernel/module.c
sound/core/pcm_compat.c
CRs-Fixed: 1010239
Signed-off-by: Runmin Wang <runminw@codeaurora.org>
Change-Id: I41a28636fc9ad91f9d979b191784609476294cdf
Use the poll_msec set by the driver that registreed an edac device
to define the poll time for how often the edac_check callback function
should be scheduled.
CRs-fixed: 1001207
Change-Id: I973d7fb966cb9f6f9497510df5de000d4f8ffcba
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Signed-off-by: Abhimanyu Kapur <abhimany@codeaurora.org>
EDAC provides a mechanism to poll for errors using a callback function
and uses a delayed timer to schedule it. Provide an option to create
a deferrable timer if the error checking is not worth waking up
the cpu from idle.
Change-Id: Ia25216323eabf7fa4b894897c950414006921f3f
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Add an EDAC device flag and associated sysfs entries to
allow an EDAC driver to be configured to panic the kernel
if a correctable error is detected. Though correctable
errors (by definition) have no adverse system effects,
a panic may still be useful, since a correctable error may
be indicative of a marginal system state.
Change-Id: I98921469254aa7b999979c1c7d9186286f982a0c
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
commit fcd5c4dd8201595d4c598c9cca5e54760277d687 upstream.
EDAC workqueue destruction is really fragile. We cancel delayed work
but if it is still running and requeues itself, we still go ahead and
destroy the workqueue and the queued work explodes when workqueue core
attempts to run it.
Make the destruction more robust by switching op_state to offline so
that requeuing stops. Cancel any pending work *synchronously* too.
EDAC i7core: Driver loaded.
general protection fault: 0000 [#1] SMP
CPU 12
Modules linked in:
Supported: Yes
Pid: 0, comm: kworker/0:1 Tainted: G IE 3.0.101-0-default #1 HP ProLiant DL380 G7
RIP: 0010:[<ffffffff8107dcd7>] [<ffffffff8107dcd7>] __queue_work+0x17/0x3f0
< ... regs ...>
Process kworker/0:1 (pid: 0, threadinfo ffff88019def6000, task ffff88019def4600)
Stack:
...
Call Trace:
call_timer_fn
run_timer_softirq
__do_softirq
call_softirq
do_softirq
irq_exit
smp_apic_timer_interrupt
apic_timer_interrupt
intel_idle
cpuidle_idle_call
cpu_idle
Code: ...
RIP __queue_work
RSP <...>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only setup a workqueue for edac devices that use the polling
method. We still try to cancel the workqueue if an edac_device
uses the irq method though. This causes a warning from debug
objects when we remove an edac device:
WARNING: CPU: 0 PID: 56 at lib/debugobjects.c:260 debug_print_object+0x98/0xc0()
ODEBUG: assert_init not available (active state 0) object type: timer_list hint: stub_timer+0x0/0x28
Modules linked in: krait_edac(-)
CPU: 0 PID: 56 Comm: rmmod Not tainted 3.12.0-rc2-00035-g15292a0 #69
(unwind_backtrace+0x0/0x144)
(show_stack+0x20/0x24)
(dump_stack+0x74/0xb4)
(warn_slowpath_common+0x78/0x9c)
(warn_slowpath_fmt+0x40/0x48)
(debug_print_object+0x98/0xc0)
(debug_object_assert_init+0xdc/0xec)
(del_timer+0x24/0x7c)
(try_to_grab_pending+0xc0/0x1b0)
(cancel_delayed_work+0x2c/0xa0)
(edac_device_workq_teardown+0x1c/0x38)
(edac_device_del_device+0xb8/0xe4)
(krait_edac_remove+0x50/0x70 [krait_edac])
(platform_drv_remove+0x24/0x28)
(__device_release_driver+0x68/0xc0)
(driver_detach+0xc4/0xc8)
(bus_remove_driver+0xac/0x114)
(driver_unregister+0x38/0x58)
(platform_driver_unregister+0x1c/0x20)
(krait_edac_driver_exit+0x14/0x1c [krait_edac])
(SyS_delete_module+0x178/0x2b4)
Fix it by skipping the workqueue teardown for such devices.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Link: http://lkml.kernel.org/r/1388434457-4194-2-git-send-email-sboyd@codeaurora.org
Signed-off-by: Borislav Petkov <bp@suse.de>
Log messages slightly differ between edac subsystems. Unifying it.
Signed-off-by: Robert Richter <robert.richter@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Robert Richter <rric@kernel.org>
* devel: (33 commits)
edac i5000, i5400: fix pointer math in i5000_get_mc_regs()
edac: allow specifying the error count with fake_inject
edac: add support for Calxeda highbank L2 cache ecc
edac: add support for Calxeda highbank memory controller
edac: create top-level debugfs directory
sb_edac: properly handle error count
i7core_edac: properly handle error count
edac: edac_mc_handle_error(): add an error_count parameter
edac: remove arch-specific parameter for the error handler
amd64_edac: Don't pass driver name as an error parameter
edac_mc: check for allocation failure in edac_mc_alloc()
edac: Increase version to 3.0.0
edac_mc: Cleanup per-dimm_info debug messages
edac: Convert debugfX to edac_dbg(X,
edac: Use more normal debugging macro style
edac: Don't add __func__ or __FILE__ for debugf[0-9] msgs
Edac: Add ABI Documentation for the new device nodes
edac: move documentation ABI to ABI/testing/sysfs-devices-edac
i7core_edac: change the mem allocation scheme to make Documentation/kobject.txt happy
edac: change the mem allocation scheme to make Documentation/kobject.txt happy
...
Use a more common debugging style.
Remove __FILE__ uses, add missing newlines,
coalesce formats and align arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The debug macro already adds that. Most of the work here was
made by this small script:
$f .=$_ while (<>);
$f =~ s/(debugf[0-9]\s*\(\s*)__FILE__\s*": /\1"/g;
$f =~ s/(debugf[0-9]\s*\(\s*)__FILE__\s*/\1/g;
$f =~ s/(debugf[0-9]\s*\(\s*)__FILE__\s*"MC: /\1"/g;
$f =~ s/(debugf[0-9]\s*\(\")\%s[\:\,\(\)]*\s*([^\"]*\s*[^\)]+)__func__\s*\,\s*/\1\2/g;
$f =~ s/(debugf[0-9]\s*\(\")\%s[\:\,\(\)]*\s*([^\"]*\s*[^\)]+),\s*__func__\s*\)/\1\2)/g;
$f =~ s/(debugf[0-9]\s*\(\"MC\:\s*)\%s[\:\,\(\)]*\s*([^\"]*\s*[^\)]+)__func__\s*\,\s*/\1\2/g;
$f =~ s/(debugf[0-9]\s*\(\"MC\:\s*)\%s[\:\,\(\)]*\s*([^\"]*\s*[^\)]+),\s*__func__\s*\)/\1\2)/g;
$f =~ s/\"MC\: \\n\"/"MC:\\n"/g;
print $f;
After running the script, manual cleanups were done to fix it the remaining
places.
While here, removed the __LINE__ on most places, as it doesn't actually give
useful info on most places.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull EDAC internal API changes from Mauro Carvalho Chehab:
"This changeset is the first part of a series of patches that fixes the
EDAC sybsystem. On this set, it changes the Kernel EDAC API in order
to properly represent the Intel i3/i5/i7, Xeon 3xxx/5xxx/7xxx, and
Intel E5-xxxx memory controllers.
The EDAC core used to assume that:
- the DRAM chip select pin is directly accessed by the memory
controller
- when multiple channels are used, they're all filled with the
same type of memory.
None of the above premises is true on Intel memory controllers since
2002, when RAMBUS and FB-DIMMs were introduced, and Advanced Memory
Buffer or by some similar technologies hides the direct access to the
DRAM pins.
So, the existing drivers for those chipsets had to lie to the EDAC
core, in general telling that just one channel is filled. That
produces some hard to understand error messages like:
EDAC MC0: CE row 3, channel 0, label "DIMM1": 1 Unknown error(s): memory read error on FATAL area : cpu=0 Err=0008:00c2 (ch=2), addr = 0xad1f73480 => socket=0, Channel=0(mask=2), rank=1
The location information there (row3 channel 0) is completely bogus:
it has no physical meaning, and are just some random values that the
driver uses to talk with the EDAC core. The error actually happened
at CPU socket 0, channel 0, slot 1, but this is not reported anywhere,
as the EDAC core doesn't know anything about the memory layout. So,
only advanced users that know how the EDAC driver works and that tests
their systems to see how DIMMs are mapped can actually benefit for
such error logs.
This patch series fixes the error report logic, in order to allow the
EDAC to expose the memory architecture used by them to the EDAC core.
So, as the EDAC core now understands how the memory is organized, it
can provide an useful report:
EDAC MC0: CE memory read error on DIMM1 (channel:0 slot:1 page:0x364b1b offset:0x600 grain:32 syndrome:0x0 - count:1 area:DRAM err_code:0001:0090 socket:0 channel_mask:1 rank:4)
The location of the DIMM where the error happened is reported by "MC0"
(cpu socket #0), at "channel:0 slot:1" location, and matches the
physical location of the DIMM.
There are two remaining issues not covered by this patch series:
- The EDAC sysfs API will still report bogus values. So,
userspace tools like edac-utils will still use the bogus data;
- Add a new tracepoint-based way to get the binary information
about the errors.
Those are on a second series of patches (also at -next), but will
probably miss the train for 3.5, due to the slow review process."
Fix up trivial conflict (due to spelling correction of removed code) in
drivers/edac/edac_device.c
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac: (42 commits)
i7core: fix ranks information at the per-channel struct
i5000: Fix the fatal error handling
i5100_edac: Fix a warning when compiled with 32 bits
i82975x_edac: Test nr_pages earlier to save a few CPU cycles
e752x_edac: provide more info about how DIMMS/ranks are mapped
i5000_edac: Fix the logic that retrieves memory information
i5400_edac: improve debug messages to better represent the filled memory
edac: Cleanup the logs for i7core and sb edac drivers
edac: Initialize the dimm label with the known information
edac: Remove the legacy EDAC ABI
x38_edac: convert driver to use the new edac ABI
tile_edac: convert driver to use the new edac ABI
sb_edac: convert driver to use the new edac ABI
r82600_edac: convert driver to use the new edac ABI
ppc4xx_edac: convert driver to use the new edac ABI
pasemi_edac: convert driver to use the new edac ABI
mv64x60_edac: convert driver to use the new edac ABI
mpc85xx_edac: convert driver to use the new edac ABI
i82975x_edac: convert driver to use the new edac ABI
i82875p_edac: convert driver to use the new edac ABI
...
The edac_align_ptr() function is used to prepare data for a single
memory allocation kzalloc() call. It counts how many bytes are needed
by some data structure.
Using it as-is is not that trivial, as the quantity of memory elements
reserved is not there, but, instead, it is on a next call.
In order to avoid mistakes when using it, move the number of allocated
elements into it, making easier to use it.
Reviewed-by: Borislav Petkov <bp@amd64.org>
Cc: Aristeu Rozanski <arozansk@redhat.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a partial revert of
15ed103a98 ("edac: Fix spelling errors")
6997991ab0 ("mips: Fix printk typos in arc/mips")
which change code that doesn't exist any more in edac/mips trees.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
After all sysdev classes are ported to regular driver core entities, the
sysdev implementation will be entirely removed from the kernel.
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Module edac_core.ko uses call_rcu() callbacks in edac_device.c, edac_mc.c
and edac_pci.c.
They all use a wait_for_completion() scheme, but this scheme it not 100%
safe on multiple CPUs. See the _rcu_barrier() implementation which
explains why extra precausion is needed.
The patch adds a comment about rcu_barrier() and as a precausion calls
rcu_barrier(). A maintainer needs to look at removing the
wait_for_completion code.
[dougthompson@xmission.com: remove the wait_for_completion code]
Signed-off-by Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add edac_device_alloc_index(), because for MAPLE platform there may
exist several EDAC driver modules that could make use of
edac_device_ctl_info structure at the same time. The index allocation
for these structures should be taken care of by EDAC core.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The edac-core driver includes code which assumes that the work_struct
which is included in every delayed_work is the first member of that
structure. This is currently the case but might change in the future, so
use to_delayed_work() instead, which doesn't make such an assumption.
linux-2.6.30-rc1 has the to_delayed_work() function that will allow this
patch to work
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is part of a larger patch series which will remove the "char
bus_id[20]" name string from struct device. The device name is managed in
the kobject anyway, and without any size limitation, and just needlessly
copied into "struct device".
[akpm@linux-foundation.org: coding-style fixes]
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When deleting an edac device, we have to wait for its edac_dev.work to be
completed before deleting the whole edac_dev structure. Since we have no
idea which work in current edac_poller's workqueue is the work we are
conerned about, we wait for all work in the edac_poller's workqueue to be
proceseed. This is done via flush_cpu_workqueue() which inserts a
wq_barrier into the tail of the workqueue and then sleeping on the
completion of this wq_barrier. The edac_poller will wake up sleepers when
it is found.
EDAC core creates only one kernel worker thread, edac_poller, to run the
works of all current edac devices. They share the same callback function
of edac_device_workq_function(), which would grab the mutex of
device_ctls_mutex first before it checks the device. This is exactly
where edac_poller and rmmod would have a great chance to deadlock.
In below call trace of rmmod > ... >
edac_device_del_device >
edac_device_workq_teardown > flush_workqueue > flush_cpu_workqueue,
device_ctls_mutex would have already been grabbed by
edac_device_del_device(). So, on one hand rmmod would sleep on the
completion of a wq_barrier, holding device_ctls_mutex; on the other hand
edac_poller would be blocked on the same mutex when it's running any one
of works of existing edac evices(Note, this edac_dev.work is likely to be
totally irrelevant to the one that is being removed right now)and never
would have a chance to run the work of above wq_barrier to wake rmmod up.
edac_device_workq_teardown() should not be called within the critical
region of device_ctls_mutex. Just like is done in edac_pci_del_device()
and edac_mc_del_mc(), where edac_pci_workq_teardown() and
edac_mc_workq_teardown() are called after related mutex are released.
Moreover, an edac_dev.work should check first if it is being removed. If
this is the case, then it should bail out immediately. Since not all of
existing edac devices are to be removed, this "shutting flag" should be
contained to edac device being removed. The current edac_dev.op_state can
be used to serve this purpose.
The original deadlock problem and the solution have been witnessed and
tested on actual hardware. Without the solution, rmmod an edac driver
would result in below deadlock:
root@localhost:/root> rmmod mv64x60_edac
EDAC DEBUG: mv64x60_dma_err_remove()
EDAC DEBUG: edac_device_del_device()
EDAC DEBUG: find_edac_device_by_dev()
(hang for a moment)
INFO: task edac-poller:2030 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
edac-poller D 00000000 0 2030 2
Call Trace:
[df159dc0] [c0071e3c] free_hot_cold_page+0x17c/0x304 (unreliable)
[df159e80] [c000a024] __switch_to+0x6c/0xa0
[df159ea0] [c03587d8] schedule+0x2f4/0x4d8
[df159f00] [c03598a8] __mutex_lock_slowpath+0xa0/0x174
[df159f40] [e1030434] edac_device_workq_function+0x28/0xd8 [edac_core]
[df159f60] [c003beb4] run_workqueue+0x114/0x218
[df159f90] [c003c674] worker_thread+0x5c/0xc8
[df159fd0] [c004106c] kthread+0x5c/0xa0
[df159ff0] [c0013538] original_kernel_thread+0x44/0x60
INFO: task rmmod:2062 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
rmmod D 0ff2c9fc 0 2062 1839
Call Trace:
[df119c00] [c0437a74] 0xc0437a74 (unreliable)
[df119cc0] [c000a024] __switch_to+0x6c/0xa0
[df119ce0] [c03587d8] schedule+0x2f4/0x4d8
[df119d40] [c03591dc] schedule_timeout+0xb0/0xf4
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 06916639e2 ("driver-core: add
dev_name() to help transition away from using bus_id") added a static
inline dev_name() and used it in dev_printk.
Unfortunately, drivers/edac/edac_core.h defines a macro called
dev_name(). Rename the latter.
Diagnosis by Tony Breeds and Michael Ellerman.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Collection of patches, merged into one, from Adrian that do the following:
1) This patch makes the following needlessly global functions static:
- edac_pci_get_log_pe()
- edac_pci_get_log_npe()
- edac_pci_get_panic_on_pe()
- edac_pci_unregister_sysfs_instance_kobj()
- edac_pci_main_kobj_setup()
2) Remove unneeded function edac_device_find()
3) Added #if 0 around function edac_pci_find()
4) make the needlessly global edac_pci_generic_check() static
5) Removed function edac_check_mc_devices()
Doug Thompson modified Adrian's patches, to bettern represent
the direction of EDAC, and make them one patch.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Acked-by: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When rounding a relative timeout we need to use round_jiffies_relative().
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ENABLE the 'logging' of CE and UE events for the EDAC_DEVICE class of error
harvester in EDAC
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some simple fixes to properly reference counter values from the block
attribute level of edac_device objects. Properly sequencing the array pointer
was added, resulting in correct identification of block level attributes from
their base class functions.
Added more verbose debug statement for event tracking.
Also during some corner testing, found a bug in the store/show sequence
of operations for the block attribute/controls management.
An old intermediate structure for 'blocks' was still in the processing
pipeline. This patch removes that old structure and correctly utilizes the
new struct edac_dev_sysfs_block_attribute for passing control from the sysfs
to the low level store/show function of the edac driver.
Now the proper kobj pointer to passed downward to the store/show
functions.
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix mutex locking deadlock on the device controller linked list. Was calling
a lock then a function that could call the same lock. Moved the cancel workq
function to outside the lock
Added some short circuit logic in the workq code
Added comments of description
Code tidying
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With feedback, this patch corrects operation of the kobject release operation
on kobjects, attributes and controls for the edac_device.
Cc: Alan Cox alan@lxorguk.ukuu.org.uk
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Refactoring of sysfs code necessitated the refactoring of the
edac_device_alloc() and edac_device_add_device() apis, of moving the index
value to the alloc() function. This patch alters the in tree drivers to
utilize this new api signature.
Having the index value performed later created a chicken-and-the-egg issue.
Moving it to the alloc() function allows for creating the necessary sysfs
entries with the proper index number
Cc: Alan Cox alan@lxorguk.ukuu.org.uk
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes and enhances the driver level set of sysfs attributes that
can be added to the 'block' level of an edac_device type of driver.
There is a controller information structure, which contains one or more
instances of device. Each instance will have one or more blocks of device
specific counters. This patch fixes the ability to have more detailed
attributes/controls for each of the 'blocks', providing for the addition of
controls/attributes from the low level driver to user space via sysfs.
Cc: Alan Cox alan@lxorguk.ukuu.org.uk
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A previous patch changed the edac_mc src file from semaphore usage to mutex
This patch changes the edac_device src file as well, from semaphore use to
mutex operation.
Use a mutex primitive for mutex operations, as it does not require a
semaphore
Cc: Alan Cox alan@lxorguk.ukuu.org.uk
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Refactored the function edac_op_state_toString() to be edac_op_state_to_string()
for consistent style, and its callers
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Refactor the edac_align_ptr() function to reduce the noise of casting the
aligned pointer to the various types of data objects and modified its callers
to its new signature
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For the file edac_device.c perform some coding style enhancements
Add some function header comments
Made for better readability commands
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes some remnant spaces inserted by the use of Lindent.
Seems Lindent adds some spaces when it shoulded. These have been fixed.
In addition, goto targets have issues, these have been fixed
in this patch.
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The error handling output strings needed to be refactored for better
displaying of the error informaton.
Also needed to added offset_value for output as well
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The origin of this code comes from patches at sourceforge, that
allow EDAC to be updated to various kernels. With kernel version 2.6.20 a
new workq system was installed, thus the patches needed to be modified
based on the kernel version. For submitting to the latest kernel.org
those #ifdefs are removed
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Run the EDAC CORE files through Lindent for cleanup
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Moving PCI to a per-instance device model
This should include the correct sysfs setup as well. Please review.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the memory controller object to work queue based implementation from the
kernel thread based.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move dev_name() macro to a more generic interface since it's not possible
to determine whether a device is pci, platform, or of_device easily.
Now each low level driver sets the name into the control structure, and
the EDAC core references the control structure for the information.
Better abstraction.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the new 'class' of object to be managed, named: 'edac_device'.
As a peer of the 'edac_mc' class of object, it provides a non-memory centric
view of an ERROR DETECTING device in hardware. It provides a sysfs interface
and an abstraction for varioius EDAC type devices.
Multiple 'instances' within the class are possible, with each 'instance'
able to have multiple 'blocks', and each 'block' having 'attributes'.
At the 'block' level there are the 'ce_count' and 'ue_count' fields
which the device driver can update and/or call edac_device_handle_XX()
functions. At each higher level are additional 'total' count fields,
which are a summation of counts below that level.
This 'edac_device' has been used to capture and present ECC errors
which are found in a a L1 and L2 system on a per CORE/CPU basis.
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
