This patch extends existing DT support for stmpe devices. This updates:
- missing header files in stmpe.c
- stmpe_of_probe() with pwm, rotator and new bindings.
- Bindings are updated in binding document.
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch allows to specify that a SPI device is connected in 3-wire mode via
device tree.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The OLPC XO-1.75 laptop includes a SDHCI controller which is 1.8v
capable, and it truthfully reports so in its capabilities. This
alternate voltage is used for driving new "UHS-I" SD cards at their
full speed.
However, what the controller doesn't know is that the motherboard
physically doesn't have a 1.8v supply available, so attempting to
switch to the 1.8v level will result in a situation that cannot be
recovered from without physically replugging the SD card.
Add a device tree flag that can be used on systems like these,
and hook it up to the equivalent SDHCI quirk.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Reviewed-by: Philip Rakity <prakity@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for pin configuration using pinctrl subsystem
to the sdhci-s3c driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
HSMMC IP on AM33xx need a special setting to handle High-speed cards.
Other platforms like TI81xx, OMAP4 may need this as-well. This depends
on the HSMMC IP timing closure done for the high speed cards.
From AM335x TRM (SPRUH73F - 18.3.12 Output Signals Generation):
The MMC/SD/SDIO output signals can be driven on either falling edge or
rising edge depending on the SD_HCTL[2] HSPE bit. This feature allows
to reach better timing performance, and thus to increase data transfer
frequency.
There are few pre-requisites for enabling the HSPE bit
- Controller should support High-Speed-Enable Bit and
- Controller should not be using DDR Mode and
- Controller should advertise that it supports High Speed in
capabilities register and
- MMC/SD clock coming out of controller > 25MHz
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add documentation for pm capabilties such as MMC_PM_KEEP_POWER
and MMC_PM_WAKE_SDIO_IRQ.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for the SD/MMC host controller found
on Wondermedia 8xxx series SoCs, currently supported under
arm/arch-vt8500.
A binding document is also included, based on mmc.txt with
additional properties.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Chris Ball <cjb@laptop.org>
Merely reorganizing documentation. No functional changes. It makes more
sense for the gpio-leds binding to be grouped with other led bindings
than with gpio drivers.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The compatible property in device tree "crypto" node has been enhanced
to provide SEC ERA information to the applications.
Signed-off-by: Vakul Garg <vakul@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The "powervr" prefix which is currently described as "Imagination
Technologies" isn't really appropriate for non-PowerVR hardware, so
deprecate it, changing the description of "powervr" to "PowerVR
(deprecated, use img)", and add a separate "img" prefix for "Imagination
Technologies Ltd.".
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch allows the STMPE GPIO driver to be successfully probed and
initialised when Device Tree support is enabled. Bindings are mentioned in
Documentation too.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add support for l2x0 cache on mvebu boards
- Depends on mvebu/everything
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQtOFbAAoJEAi3KVZQDZAeRbkH/3IWYaAFXi6wnM4yHdYJbp5A
X1375b4Tkjd2Q05gujtNZLDS1gR4O65gJ9nxoV4OuYtqt1WnFUTDU4WozaYFdj8G
1hojkI6qKUddV+EZdMkx1/0YXORsNbGx8PHFPzsLfMHL/qEWjdMgOf4UW+9AogVt
hOwQwIs7SuhDnu0QR0dUH65iU848n5dYSczr/j71l2fqooJ/+KaU1hKKYf/rFvX2
3f9TaDydeglgAUGs7FUL1EbuLQiygIGy1wDhxyVK+g7inAzdQGzVZ7faK8M3NScM
YixWH+uy35ZAS8LlPCpY7DFts4pMtB/5fFvWiMYaBXv53mClgqSaymQDZLObJi8=
=rcOU
-----END PGP SIGNATURE-----
Merge tag 'mvebu_cache_l2x0_for_3.8' of git://git.infradead.org/users/jcooper/linux into late/mvebu
From Jason Cooper:
mvebu cache-l2x0 for v3.8
- Add support for l2x0 cache on mvebu boards
- Depends on mvebu/everything
* tag 'mvebu_cache_l2x0_for_3.8' of git://git.infradead.org/users/jcooper/linux:
arm: l2x0: add aurora related properties to OF binding
arm: mvebu: add Aurora L2 Cache Controller to the DT
arm: mvebu: add L2 cache support
- due to the complex interdependencies of the received pull requests
I decided to keep this in one branch the way they recommended merging it
- this was their first attempt at doing pull requests, we'll work on it
with them
- added SMP support for mvebu SoCs
- added coherency fabric
- added mdio and mvneta drivers
- added mirabox board
- added openblocks ax3-4 board
- clock fixes and improvements
- converted mv_xor driver to devicetree (extensive series in itself)
merge conflicts with orion/*
- arch/arm/mach-kirkwood/Kconfig
- select everything
- arch/arm/mach-kirkwood/board-dt.c
- remove AUXDATA
- keep all of_machine_is_compatible()
- use of_platform_populate(NULL, kirkwood_dt_match_table, NULL, NULL)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQsFAhAAoJEAi3KVZQDZAedzgH/3VodO3dDqL4A5HCoUj56HXF
Chkv1cl+1VS3sPnsbbluG0fmDdB619i4Oi2bUWc1YdLpEE0xgyjeAzl5vZDFBjrS
tb8nhWCd2vEcKFSC+HVU2Rhj0NwgUoQifoeD7NSovYZJE6+z+KEY5ny0sE4uaWE1
NL+StBI9dH+SvMi59rnsAxteAnBEAosUoY4KaoHcTHvPsqm9xW5GBh1MkSXQB7fx
kwRrdCaM8U3y3J933/Y4C3maDDQVL7v27YgQp+U5r/eRyN7fVVccxLr6xwl9sck2
fjEpbNRYMImvCOKh8+dhllf/8ZOmjdOore4ORbk4Ulame2KL6pG/2fZ+5N+FrRQ=
=QHBZ
-----END PGP SIGNATURE-----
Merge tag 'mvebu_everything_for_3.8' of git://git.infradead.org/users/jcooper/linux into late/mvebu
From Jason Cooper. Unfortunately this is a combined branch with all
mvebu code as one drop, something we normally try to avoid and instead
slice vendor topics across our branches. Hopefully we can avoid doing
this again for 3.9!
mvebu everything for v3.8
- due to the complex interdependencies of the received pull requests
I decided to keep this in one branch the way they recommended merging it
- this was their first attempt at doing pull requests, we'll work on it
with them
- added SMP support for mvebu SoCs
- added coherency fabric
- added mdio and mvneta drivers
- added mirabox board
- added openblocks ax3-4 board
- clock fixes and improvements
- converted mv_xor driver to devicetree (extensive series in itself)
* tag 'mvebu_everything_for_3.8' of git://git.infradead.org/users/jcooper/linux: (85 commits)
dma: mv_xor: fix error handling path
dma: mv_xor: fix error checking of irq_of_parse_and_map()
dma: mv_xor: use request_irq() instead of devm_request_irq()
dma: mv_xor: clear the window override control registers
arm: mvebu: fix address decoding armada_cfg_base() function
ARM: mvebu: update defconfig with I2C and RTC support
ARM: mvebu: Add SATA support for OpenBlocks AX3-4
ARM: mvebu: Add support for the RTC in OpenBlocks AX3-4
ARM: mvebu: Add support for I2C on OpenBlocks AX3-4
ARM: mvebu: Add support for I2C controllers in Armada 370/XP
arm: mvebu: Add hardware I/O Coherency support
arm: plat-orion: Add coherency attribute when setup mbus target
arm: dma mapping: Export a dma ops function arm_dma_set_mask
arm: mvebu: Add SMP support for Armada XP
arm: mm: Add support for PJ4B cpu and init routines
arm: mvebu: Add IPI support via doorbells
arm: mvebu: Add initial support for power managmement service unit
arm: mvebu: Add support for coherency fabric in mach-mvebu
arm: mvebu: update defconfig to include XOR driver
arm: mvebu: update defconfig to include network driver
...
Signed-off-by: Olof Johansson <olof@lixom.net>
and to get rid of CONFIG_OMAP_32K_TIMER and rely on the board
or devicetree provided timer configuration.
Note that these changes are on top of the recent timer fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=XZ+L
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Timer clean-up to get us closer to moving timer code to drivers,
and to get rid of CONFIG_OMAP_32K_TIMER and rely on the board
or devicetree provided timer configuration.
Note that these changes are on top of the recent timer fixes.
By Jon Hunter (32) and others
via Tony Lindgren
* tag 'omap-for-v3.8/cleanup-timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (71 commits)
ARM: OMAP3: cm-t3517: use GPTIMER for system clock
ARM: OMAP2+: timer: remove CONFIG_OMAP_32K_TIMER
ARM: OMAP2+: Fix compiler warning for 32k timer
ARM: OMAP: Remove unnecessary inclusion of dmtimer.h
ARM: OMAP: Add platform data header for DMTIMERs
ARM: OMAP: Remove unnecessary omap_dm_timer structure declaration
ARM: OMAP2+: Remove unnecessary local variable in timer code
ARM: OMAP: Don't store timers physical address
ARM: OMAP: Define omap_dm_timer_prepare function as static
ARM: OMAP: Clean-up dmtimer reset code
ARM: OMAP: Remove __omap_dm_timer_set_source function
ARM: OMAP: Remove unnecessary call to clk_get()
ARM: OMAP: Add dmtimer interrupt disable function
ARM: OMAP: Fix spurious interrupts when using timer match feature
ARM: OMAP: Don't restore DMTIMER interrupt status register
ARM: OMAP: Don't restore of DMTIMER TISTAT register
ARM: OMAP: Fix dmtimer reset for timer1
ARM: OMAP2+: Don't use __omap_dm_timer_reset()
ARM: OMAP2/3: Define HWMOD software reset status for DMTIMERs
ARM: OMAP3: Correct HWMOD DMTIMER SYSC register declarations
...
Change/change conflict in arch/arm/mach-omap2/board-cm-t3517.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
* pm-cpufreq: (21 commits)
cpufreq: ondemand: update sampling rate only on right CPUs
cpufreq: SPEAr: Add CPUFreq driver
cpufreq: governors: Fix jiffies/cputime mixup (revisited)
cpufreq: ondemand: fix wrong delay sampling rate
cpufreq: exynos: Use static for functions used in only this file
cpufreq: exynos: Broadcast frequency change notifications for all cores
cpufreq: remove use of __devexit
cpufreq: remove use of __devinit
cpufreq: remove use of __devexit_p
cpufreq: Remove unnecessary initialization of a local variable
cpufreq: Make sure target freq is within limits
cpufreq: Avoid calling cpufreq driver's target() routine if target_freq == policy->cur
cpufreq: Fix sparse warning by making local function static
cpufreq: Fix sparse warnings by updating cputime64_t to u64
cpufreq: governors: remove redundant code
cpufreq: return early from __cpufreq_driver_getavg()
cpufreq: fix jiffies/cputime mixup in conservative/ondemand governors
cpufreq: Improve debug prints
cpufreq: Move common part from governors to separate file, v2
cpufreq / core: Fix printing of governor and driver name
...
Exynos DP changes for the 3.8 merge window.
- Device Tree support for Samsung Exynos DP
- SW Link training is cleaned up.
- HPD interrupt is supported.
* 'exynos-dp-next' of git://github.com/jingoo/linux:
video: exynos_dp: remove redundant parameters
video: exynos_dp: Fix incorrect setting for INT_CTL
video: exynos_dp: Reset and initialize DP before requesting irq
video: exynos_dp: Enable hotplug interrupts
video: exynos_dp: Move hotplug into a workqueue
video: exynos_dp: Remove sink control to D0
video: exynos_dp: Fix bug when checking dp->irq
video: exynos_dp: Improve EDID error handling
video: exynos_dp: Get pll lock before pattern set
video: exynos_dp: Clean up SW link training
video: exynos_dp: Check DPCD return codes
video: exynos_dp: device tree documentation
video: exynos_dp: Add device tree support to DP driver
Add documentation for the DT bindings in exynos display port driver.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Handle the jack detection inforamtion as bool from devicetree.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The driver supports the following LED outputs as generic PWM driver:
TWL4030 LEDA and LEDB (PWMA and PWMB)
TWL6030 Charging indicator LED (PWM LED)
On TWL6030 when the PWM requested LED is configured to be controlled by SW.
In this case the user can enable/disable and set the duty period freely.
When the PWM has been freed, the LED driver is put back to HW control.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
The driver supports the following PWM outputs:
TWL4030 PWM0 and PWM1
TWL6030 PWM1 and PWM2
On TWL4030 the PWM signals are muxed. Upon requesting the PWM the driver
will select the correct mux so the PWM can be used. When the PWM has been
freed the original configuration is going to be restored.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This patch
1. Add support for device-tree binding for EHRWPM driver.
2. Set size of pwm-cells set to 3 to support PWM channel number, PWM
period & polarity configuration from device tree.
3. Add enable/disable clock gating in PWM subsystem common config space.
4. When here set .owner member in platform_driver structure to
THIS_MODULE.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This patch
1. Add support for device-tree binding for ECAP APWM driver.
2. Set size of pwm-cells set to 3 to support PWM channel number, PWM
period & polarity configuration from device tree.
3. Add enable/disable clock gating in PWM subsystem common config space.
4. When here set .owner member in platform_driver structure to
THIS_MODULE.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
In some platforms (like am33xx), PWM sub modules (ECAP, EHRPWM, EQEP)
are integrated to PWM subsystem. These PWM submodules has resources
shared and only one register bit-field is provided to control
module/clock enable/disable, makes it difficult to handle common
resources from independent PWMSS submodule drivers.
So the solution here implemented in this patch is, to create driver for
PWMSS and take the role of parent driver for PWM submodules. PWMSS
parent driver enumerates all the child nodes under PWMSS module. Also
symbol "pwmss_submodule_state_change" exported to enable clock gating
for individual PWMSS submodules, and submodule drivers has to enable
clock gating from their drivers.
As this is only supported during DT boot, the parent/child relationship
is created and populated in DT execution flow. The only required change
is inside DTS file, making EHRPWM & ECAP as a child to PWMSS node.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Add device tree based discovery support for max8997.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Aurora is a L2 Cache Controller designed to be compatible with the
L2x0 Cache Controller. L2X0 OF bindings are extended to support some
specificity of Aurora (no cache id part number available through
hardware, always write through mode, choice between outer cache and
system cache).
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Tested-and-reviewed-by: Lior Amsalem <alior@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Barry Song <21cnbao@gmail.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
SPEAr is an ARM based family of SoCs. This patch adds in support of cpufreq
driver for SPEAr SoCs. It is supported via DT only and so bindings are present
in binding document.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This series will do the following:
- Switch the Integrator/AP and /CP to use the SoC bus
when booting from device tree.
- Group all devices on the SoC below this bus so as to
set a good example of how to do this. The bus was
invented by Lee Jones, let's show how it's to be used
on a DT:ed SoC.
- Fetch the special system controller offsets from two
special device tree nodes for each case and replace
the static mappings with these at boot.
- Move some static remaps to the ATAG-only code path
and delete some static maps that aren't used.
- Push dependencies on system controller remaps down
to the Integrator/AP board file and the PCIv3 driver
respectively and use only dynamic remappings.
- Fix up conditional BUG() usage in the PCIv3 driver
to be simpler and more to the point.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=zpgo
-----END PGP SIGNATURE-----
Merge tag 'integrator-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/cleanup
From Linus Walleij <linus.walleij@linaro.org>:
This series will do the following:
- Switch the Integrator/AP and /CP to use the SoC bus
when booting from device tree.
- Group all devices on the SoC below this bus so as to
set a good example of how to do this. The bus was
invented by Lee Jones, let's show how it's to be used
on a DT:ed SoC.
- Fetch the special system controller offsets from two
special device tree nodes for each case and replace
the static mappings with these at boot.
- Move some static remaps to the ATAG-only code path
and delete some static maps that aren't used.
- Push dependencies on system controller remaps down
to the Integrator/AP board file and the PCIv3 driver
respectively and use only dynamic remappings.
- Fix up conditional BUG() usage in the PCIv3 driver
to be simpler and more to the point.
* tag 'integrator-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: integrator: use BUG_ON where possible
ARM: integrator: push down SC dependencies
ARM: integrator: delete static UART1 mapping
ARM: integrator: delete SC mapping on the CP
ARM: integrator: remove static CP syscon mapping
ARM: integrator: remove static AP syscon mapping
ARM: integrator: hook the CP into the SoC bus
ARM: integrator: hook the AP into the SoC bus
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
SPEAr3xx architecture includes shared/multiplexed irqs for certain set
of devices. The multiplexor provides a single interrupt to parent
interrupt controller (VIC) on behalf of a group of devices.
There can be multiple groups available on SPEAr3xx variants but not
exceeding 4. The number of devices in a group can differ, further they
may share same set of status/mask registers spanning across different
bit masks. Also in some cases the group may not have enable or other
registers. This makes software little complex.
Present implementation was non-DT and had few complex data structures to
decipher banks, number of irqs supported, mask and registers involved.
This patch simplifies the overall design and convert it in to DT. It
also removes all registration from individual SoC files and bring them
in to common shirq.c.
Also updated the corresponding documentation for DT binding of shirq.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
- ehci-orion dt binding
- gpio-poweroff
- use dt regulators
- move mpp to DT/pinctrl
Depends on:
- orion/boards
- merge conflicts
- keep all 'select's in Kconfig
- remove all #includes in board-*.c
- pinctrl/devel up to:
- 06763c7 pinctrl: mvebu: move to its own directory
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQsEfdAAoJEAi3KVZQDZAeBd8IAIAkBGIJyUJSmQJEWkZ/9ezq
UOLec1t/TnLhAQ1Sk8g4C41wmHKYNqmZSVaAXC+QP6Yw+Gdhlw+V6YBjOYDzA7Y4
k8ljw3SFbvS+AIx0qK26j6Tf6En2H5lMXsdlKoarCV+G+MxAHsQO7jL6y7BFwTlX
QnwJFz+NRzMFxaPiCS+43oZuxIIzkHe8wKMb0y7nSiNQYUUv8TdKvyK+ekFuszOp
v6uo/MI1p1/xdUxDbEKxOwmUjAy7x+t0LUFi1dsWuiDHdrG+BVT4NkJuFaD8Ui13
VoUD1ogyWHQZV2hq0dfj+9Hed5NEgl6toAzGN9LPLmsuVUXCnB2CdBprhuDv5F8=
=yaX1
-----END PGP SIGNATURE-----
Merge tag 'orion_dt_for_3.8' of git://git.infradead.org/users/jcooper/linux into next/dt
From Jason Cooper:
orion dt for v3.8
- ehci-orion dt binding
- gpio-poweroff
- use dt regulators
- move mpp to DT/pinctrl
Depends on:
- orion/boards
- merge conflicts
- keep all 'select's in Kconfig
- remove all #includes in board-*.c
- pinctrl/devel up to:
- 06763c7 pinctrl: mvebu: move to its own directory
* tag 'orion_dt_for_3.8' of git://git.infradead.org/users/jcooper/linux: (211 commits)
ARM: Kirkwood: remove kirkwood_ehci_init() from new boards
ARM: Kirkwood: Add support LED of OpenBlocks A6
ARM: Kirkwood: Convert to EHCI via DT for OpenBlocks A6
ARM: kirkwood: Add NAND partiton map for OpenBlocks A6
ARM: kirkwood: Add support second I2C bus and RTC on OpenBlocks A6
ARM: kirkwood: Add support DT of second I2C bus
ARM: kirkwood: Convert mplcec4 board to pinctrl
ARM: Kirkwood: Convert km_kirkwood to pinctrl
ARM: Kirkwood: support 98DX412x kirkwoods with pinctrl
ARM: Kirkwood: Convert IX2-200 to pinctrl.
ARM: Kirkwood: Convert lsxl boards to pinctrl.
ARM: Kirkwood: Convert ib62x0 to pinctrl.
ARM: Kirkwood: Convert GoFlex Net to pinctrl.
ARM: Kirkwood: Convert dreamplug to pinctrl.
ARM: Kirkwood: Convert dockstar to pinctrl.
ARM: Kirkwood: Convert dnskw to pinctrl
ARM: Kirkwood: Convert iConnect to pinctrl.
ARM: Kirkwood: Convert TS219 to pinctrl.
ARM: Kirkwood: Add DTSI files for pinctrl
ARM: Kirkwood: Make use of mvebu pincltl and gpio drivers
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- mach-orion5x/ joins the dark side! (devicetree)
- Lacie Network Space family
- Lacie Ethernet Disk mini v2
- USI TopKick
- ZyXEL NSA310
- MPL CEC4
- Plat'Home OpenBlocks A6 (kirkwood, AX3-4 is armada xp)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQrc/qAAoJEAi3KVZQDZAeGIcIAJ70hcz/cKdEKNpekMRoMWpz
LoDXtPqRuUvCqBdUNFkJyPAhHHkWwnU6KRcBRz1dknTtJ7nyCkDQYRG/JIroIs8I
X9N6JbPH7FMU+Z1ZUAM2ww+pEAIQkwX06erAy9u/a7ivMj/0LeXboNK+ngIx1jgL
xz2SS4wJrujPwvT2rYo4nJ+WwGiiIPbRjiY7r87rD/DQ9nY9DxKgfve7pRhaCCZS
Baw48u8qTe6M9LGcXw+b/MSHGCTB6YabqaRHMAr/1NK0Z3JDGU8tEpOuMCnFX7SA
6CxEymw5/8fzyTgdRz7FRd9Hg28y5Cd+T2l48X4tSL/M16H4EeBOxj6ub4zCi9s=
=nsDw
-----END PGP SIGNATURE-----
Merge tag 'orion_boards_for_3.8' of git://git.infradead.org/users/jcooper/linux into next/boards
From Jason Cooper:
orion boards for v3.8
- mach-orion5x/ joins the dark side! (devicetree)
- Lacie Network Space family
- Lacie Ethernet Disk mini v2
- USI TopKick
- ZyXEL NSA310
- MPL CEC4
- Plat'Home OpenBlocks A6 (kirkwood, AX3-4 is armada xp)
* tag 'orion_boards_for_3.8' of git://git.infradead.org/users/jcooper/linux:
ARM: kirkwood: Add Plat'Home OpenBlocks A6 support
ARM: Dove: update defconfig
ARM: Kirkwood: update defconfig for new boards
arm: orion5x: add DT related options in defconfig
arm: orion5x: convert 'LaCie Ethernet Disk mini v2' to Device Tree
arm: orion5x: basic Device Tree support
arm: orion5x: mechanical defconfig update
ARM: kirkwood: Add support for the MPL CEC4
arm: kirkwood: add support for ZyXEL NSA310
ARM: Kirkwood: new board USI Topkick
ARM: kirkwood: use gpio-fan DT binding on lsxl
ARM: Kirkwood: add Netspace boards to defconfig
ARM: kirkwood: DT board setup for Network Space Mini v2
ARM: kirkwood: DT board setup for Network Space Lite v2
ARM: kirkwood: DT board setup for Network Space v2 and parents
leds: leds-ns2: add device tree binding
ARM: Kirkwood: Enable the second I2C bus
From Kukjin Kim:
Here is second Samsung DT stuff for v3.8.
This is including power domain DT support for exynos and Google ARM
Chromebook, Snow board and exynos4210-origen updates.
* 'next/dt-samsung-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Use drive strength 3 for SD pins for exynos4
ARM: dts: Set up power domains for exynos4
ARM: EXYNOS: Bind devices to power domains using DT
ARM: EXYNOS: Fix power domain name initialization
ARM: EXYNOS: Detect power domain state on registration from DT
ARM: dts: Add vmmc fixed voltage regulator for exynos4210-origen
ARM: dts: Update sdhci nodes for current bindings for exynos4210-origen
ARM: dts: Update for pinctrl-samsung driver for exynos4210-origen
ARM: dts: Split memory sections for exynos4210-origen
ARM: EXYNOS: add all i2c busses to auxdata for DT
ARM: dts: Add aliases for i2c controller for exynos4
ARM: dts: Add board dts file for Snow board (ARM Chromebook)
ARM: dts: Move the dwmmc aliases from smdk5250 dts to exynos
Add/add conflicts resolved in arch/arm/boot/dts/exynos5250-smdk5250.dts
and arch/arm/mach-exynos/mach-exynos5-dt.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=IZiZ
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-1' of git://git.pengutronix.de/git/imx/linux-2.6 into next/soc
From Sascha Hauer:
ARM i.MX SoC updates for v3.8
* tag 'imx-soc-1' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM i.MX6: remove gate_mask from pllv3
ARM i.MX6: Fix ethernet PLL clocks
ARM i.MX6: rename PLLs according to datasheet
ARM i.MX6: Add pwm support
ARM i.MX51: Add pwm support
ARM i.MX53: Add pwm support
ARM: mx5: Replace clk_register_clkdev with clock DT lookup
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQss0FAAoJEHm+PkMAQRiG6cEH/An3PYsWBBy27tzoLyVfJKF1
3m3vR8HS2tnHg6erxms+738jos59vrWXV0Ygnvw0DHbGR0HNb4rkwce/KXu/jgOD
MRYNYhlhMFJTEUFrSrcwKITrAV3kVPWXxPXgAR6Gzpr6NPKKM9TBzEv0ze56TFYz
asOxqeBcPSS7aFZlkoNsy1wG4l0Quo5ke8VZIxo9Me5qlqubAoZ6pING4wAGXqeE
tf81CevSdpe0nqr8/dlYyCvLjrurgpJQczxRCBI3mP6kLWGfUCVzZmcu86PfT9b+
35zNJwDneIoN+D9bVDHy6mrq9uQdmhWnQuhv1joTPn6RDn1nyBRBd+A5qLxSov4=
=CPoy
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc7' into next/cleanup
Merging in mainline back to next/cleanup since it has collected a few
conflicts between fixes going upstream and some of the cleanup patches.
Git doesn't auto-resolve some of them, and they're mostly noise so let's
take care of it locally.
Conflicts are in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
arch/arm/plat-omap/i2c.c
drivers/video/omap2/dss/dss.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
drivers/net/wireless/iwlwifi/pcie/tx.c
Minor iwlwifi conflict in TX queue disabling between 'net', which
removed a bogus warning, and 'net-next' which added some status
register poking code.
Signed-off-by: David S. Miller <davem@davemloft.net>
The RaidEngine is a new Freescale hardware that used for parity
computation offloading in RAID5/6.
This patch adds the device node in device tree and related binding
documentation.
Signed-off-by: Harninder Rai <harninder.rai@freescale.com>
Signed-off-by: Naveen Burmi <naveenburmi@freescale.com>
Signed-off-by: Xuelin Shi <b29237@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
