From Jason Cooper:
New drivers:
- pinctrl (dove, kirkwood, mvebu)
- gpio (mvebu)
* 'kirkwood/drivers' of git://git.infradead.org/users/jcooper/linux:
arm: mvebu: add gpio support in defconfig
arm: mvebu: add DT information for GPIO banks on Armada 370 and XP
arm: mvebu: use GPIO support now that a driver is available
Documentation: add description of DT binding for the gpio-mvebu driver
gpio: introduce gpio-mvebu driver for Marvell SoCs
arm: mvebu: select the pinctrl drivers for Armada 370 and Armada XP platforms
arm: mvebu: split Kconfig options for Armada 370 and XP
ARM: mvebu: adjust Armada XP evaluation board DTS
ARM: mvebu: Add pinctrl support to Armada 370 SoC
ARM: mvebu: Add pinctrl support to Armada XP SoCs
pinctrl: mvebu: add pinctrl driver for Armada XP
pinctrl: mvebu: add pinctrl driver for Armada 370
pinctrl: mvebu: kirkwood pinctrl driver
pinctrl: mvebu: dove pinctrl driver
pinctrl: mvebu: pinctrl driver core
Signed-off-by: Olof Johansson <olof@lixom.net>
From Jason Cooper:
New bindings:
- iconnect nand and keys
- mv_cesa
- gpio-fan
* 'kirkwood/dt' of git://git.infradead.org/users/jcooper/linux:
ARM: kirkwood: Use devicetree to define DNS-32[05] fan
hwmon: Add devicetree bindings to gpio-fan
Crypto: CESA: Add support for DT based instantiation.
ARM: Kirkwood: Describe iconnect nand in DT.
ARM: Kirkwood: Describe iconnect keys in DT.
Support for loading the twl4030 audio module via devicetree.
Sub devices for codec and vibra will be created as mfd devices once the
core MFD driver is loaded when the kernel is booted with a DT blob.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This pinctrl driver is not a full-blown pinctrl driver from scratch:
it relies on the common pinctrl-mvebu driver, which is used for all
Marvell EBU SoCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This pinctrl driver is not a full-blown pinctrl driver from scratch:
it relies on the common pinctrl-mvebu driver, which is used for all
Marvell EBU SoCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds a SoC specific pinctrl driver for Marvell Kirkwood SoCs
plus DT binding documentation. This driver will use the mvebu pinctrl
driver core.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds a SoC specific pinctrl driver for Marvell Dove SoCs
plus DT binding documentation. This driver will use the mvebu pinctrl
driver core.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds a pinctrl driver core for Marvell SoCs plus DT
binding documentation. This core driver will be used by SoC family
specific drivers, i.e. Armada XP, Armada 370, Dove, Kirkwood, aso.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Conflicts:
arch/arm/Kconfig
Allow a gpio-fan to be defined in devicetree, see binding documentation
for details.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Based on work by Michael Walle and Jason Cooper.
Added support for getting the interrupt number and address of SRAM
from DT.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Conflicts:
arch/arm/mach-kirkwood/board-dt.c
Add device tree support to C_CAN/D_CAN controller and usage details
are added to device tree documentation. Driver was tested on AM335x
EVM.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
For the of binding doc:
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Bindings for gpio, interrupt controller, power management controller,
timer, realtime clock, serial uart, ehci and uhci controllers and
framebuffer controllers used on the arch-vt8500 platform.
Framebuffer binding also specifies a 'display' node which is required
for determining the lcd panel data.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
* next/soc: (50 commits)
ARM: OMAP: AM33xx hwmod: fixup SPI after platform_data move
MAINTAINERS: add an entry for the BCM2835 ARM sub-architecture
ARM: bcm2835: instantiate console UART
ARM: bcm2835: add stub clock driver
ARM: bcm2835: add system timer
ARM: bcm2835: add interrupt controller driver
ARM: add infra-structure for BCM2835 and Raspberry Pi
ARM: tegra20: add CPU hotplug support
ARM: tegra30: add CPU hotplug support
ARM: tegra: clean up the common assembly macros into sleep.h
ARM: tegra: replace the CPU CAR access code by tegra_cpu_car_ops
ARM: tegra: introduce tegra_cpu_car_ops structures
ARM: Tegra: Add smp_twd clock for Tegra20
ARM: AM33XX: clock: Add dcan clock aliases for device-tree
ARM: OMAP2+: dpll: Add missing soc_is_am33xx() check for common functions
ARM: OMAP: omap_device: idle devices with no driver bound
ARM: OMAP: omap_device: don't attempt late suspend if no driver bound
ARM: OMAP: omap_device: keep track of driver bound status
ARM: OMAP3+: hwmod: Add AM33XX HWMOD data
ARM: OMAP2+: hwmod: Hook-up am33xx support in omap_hwmod framework
...
Change/remove conflict in arch/arm/mach-ux500/clock.c resolved.
Signed-off-by: Olof Johansson <olof@lixom.net>
The BCM2835 is an ARM SoC from Broadcom. This patch adds very basic
support for this SoC; enough to boot the system into an initrd with
UART console, interrupt controller, timers, and a stub clock driver.
Also provided is a similarly basic device tree for the Raspberry Pi
Model B board.
This series was written by Simon Arlott, Chris Boot, and Dom Cobley
downstream, with reference to a Broadcom tree, and modified for upstream
and submitted by Stephen Warren.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vqsx
-----END PGP SIGNATURE-----
Merge tag 'rpi-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi into next/soc
ARM: add basic BCM2835 SoC and Raspberry Pi board support
The BCM2835 is an ARM SoC from Broadcom. This patch adds very basic
support for this SoC; enough to boot the system into an initrd with
UART console, interrupt controller, timers, and a stub clock driver.
Also provided is a similarly basic device tree for the Raspberry Pi
Model B board.
This series was written by Simon Arlott, Chris Boot, and Dom Cobley
downstream, with reference to a Broadcom tree, and modified for upstream
and submitted by Stephen Warren.
* tag 'rpi-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi:
MAINTAINERS: add an entry for the BCM2835 ARM sub-architecture
ARM: bcm2835: instantiate console UART
ARM: bcm2835: add stub clock driver
ARM: bcm2835: add system timer
ARM: bcm2835: add interrupt controller driver
ARM: add infra-structure for BCM2835 and Raspberry Pi
From Kukjin Kim:
Here is G-Scaler DT for supporting EXYNOS5 SoCs.
* 'next/dt-gscaler' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Adds G-Scaler device from Device Tree
ARM: EXYNOS: Add clock support for G-Scaler
From Kukjin Kim:
This branch is for supporting pinctrl for Samsung EXYNOS. Now this can
support EXYNOS4210 and other EXYNOS SoCs such as EXYNOS4X12 will be
supported next time.
* 'next/pinctrl-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
gpio: exynos4: skip gpiolib registration if pinctrl driver is used
pinctrl: add exynos4210 specific extensions for samsung pinctrl driver
pinctrl: add samsung pinctrl and gpiolib driver
From Kukjin Kim:
Since there are many changes for gpio-samsung in my tree, this has been
included in my tree with Linus' agreement.
* 'next/gpio-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
gpio: samsung: add devicetree init for s3c24xx arches
Note that this branch is based on omap-cleanup-sparseirq-for-v3.7
to avoid merge conflicts with the sparseirq changes for gpio-twl4030
driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=fzT6
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-dt-merged-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Device tree related changes for omaps.
Note that this branch is based on omap-cleanup-sparseirq-for-v3.7
to avoid merge conflicts with the sparseirq changes for gpio-twl4030
driver.
* tag 'omap-devel-dt-merged-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/dts: Mux uart pins for omap4-sdp
ARM: OMAP2+: select PINCTRL in Kconfig
arm/dts: Add pinctrl driver entries for omap2/3/4
arm/dts: Add omap36xx.dtsi file and rename omap3-beagle to omap3-beagle-xm
ARM: dts: omap3-overo: Add support for the blue LED
Documentation: dt: Update the OMAP documentation with Overo/Toby
ARM: dts: OMAP3: Add support for Gumstix Overo with Tobi expansion board
ARM: dts: OMAP4: Add reg and interrupts for every nodes
ARM: dts: AM33XX: Specify reg and interrupt property for all nodes
ARM: dts: AM33XX: Convert all hex numbers to lower-case
ARM: dts: omap3-beagle: Enable audio support
ARM: dts: omap5: Add McPDM and DMIC section to the dtsi file
ARM: dts: omap5: Add McBSP entries
ARM: dts: omap4: Add reg-names for McPDM and DMIC
ARM: dts: omap4: Add McBSP entries
ARM: dts: omap3: Add McBSP entries
ARM: dts: omap2420-h4: Include omap2420.dtsi file instead the common omap2
ARM: dts: omap2: Add McBSP entries for OMAP2420 and OMAP2430 SoC
ARM: dts: omap3-beagle: Add heartbeat and mmc LEDs support
ARM: dts: omap3: Add gpio-twl4030 properties for BeagleBoard and omap3-EVM
...
Here we document the AB8500 Audio CODEC in the existing MFD AB8500 document.
CC: alsa-devel@alsa-project.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we add the required documentation for the new Device Tree
bindings pertaining to the MSP CPU-side DAI Driver.
Acked-by: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we add the required documentation for the new Device Tree
bindings pertaining to the MOP500 Audio Machine driver.
Acked-by: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Instead of having to duplicate the description of the properties needed
for interrupt support, reference the new standard document.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
[Minor spelling correction]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The System Timer peripheral provides four 32-bit timer channels and a
single 64-bit free running counter. Each channel has an output compare
register, which is compared against the 32 least significant bits of the
free running counter values, and generates an interrupt.
Timer 3 is used as the Linux timer.
The BCM2835 also contains an SP804-based timer module. However, it
apparently has significant differences from the standard SP804 IP block,
and Broadcom's documentation recommends using the system timer instead.
This patch was extracted from git://github.com/lp0/linux.git branch
rpi-split as of 2012/09/08, and modified as follows:
* s/bcm2708/bcm2835/.
* Modified device tree vendor prefix.
* Moved to drivers/clocksource/. This looks like the desired location for
such code now.
* Added DT binding docs.
* Moved struct sys_timer bcm2835_timer into time.c to encapsulate it more.
* Simplified bcm2835_time_init() to find one matching node and operate on
it, rather than looping over all matching nodes. This seems more
consistent with other clocksource code.
* Simplified bcm2835_time_init() using of_iomap().
* Renamed struct bcm2835_timer.index to match_mask to better represent its
purpose.
* s/printk(PR_INFO/pr_info(/
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Dom Cobley <dc4@broadcom.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The BCM2835 contains a custom interrupt controller, which supports 72
interrupt sources using a 2-level register scheme. The interrupt
controller, or the HW block containing it, is referred to occasionally
as "armctrl" in the SoC documentation, hence the symbol naming in the
code.
This patch was extracted from git://github.com/lp0/linux.git branch
rpi-split as of 2012/09/08, and modified as follows:
* s/bcm2708/bcm2835/.
* Modified device tree vendor prefix.
* Moved implementation to drivers/irchip/.
* Added devicetree documentation, and hence removed list of IRQs from
bcm2835.dtsi.
* Changed shift in MAKE_HWIRQ() and HWIRQ_BANK() from 8 to 5 to reduce
the size of the hwirq space, and pass the total size of the hwirq space
to irq_domain_add_linear(), rather than just the number of valid hwirqs;
the two are different due to the hwirq space being sparse.
* Added the interrupt controller DT node to the top-level of the DT,
rather than nesting it inside a /axi node. Hence, changed the reg value
since /axi had a ranges property. This seems simpler to me, but I'm not
sure if everyone will like this change or not.
* Don't set struct irq_domain_ops.map = irq_domain_simple_map, hence
removing the need to patch include/linux/irqdomain.h or
kernel/irq/irqdomain.c.
* Simplified armctrl_of_init() using of_iomap().
* Removed unused IS_VALID_BANK()/IS_VALID_IRQ() macros.
* Renamed armctrl_handle_irq() to prevent possible symbol clashes.
* Made armctrl_of_init() static.
* Removed comment "Each bank is registered as a separate interrupt
controller" since this is no longer true.
* Removed FSF address from license header.
* Added my name to copyright header.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Dom Cobley <dc4@broadcom.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The BCM2835 is an ARM SoC from Broadcom. This patch adds very basic
support for this SoC.
http://www.broadcom.com/products/BCM2835http://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
Note that the documentation in the latter .pdf assumes the MMU setup
that's used on the "VideoCore" companion processor, and does not document
physical peripheral addresses. Subtract 0x5e000000 to obtain the physical
addresses. This is accounted for by the ranges property in the /soc node
in the device tree.
The BCM2835 SoC is used in the Raspberry Pi. This patch also adds a
minimal device tree for this board; enough to see some very early kernel
boot messages through earlyprintk. However, this patch does not yet
provide a useful booting system.
http://www.raspberrypi.org/.
This patch was extracted from git://github.com/lp0/linux.git branch
rpi-split from 3-4 months ago, and significantly stripped down and
modified since.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Dom Cobley <dc4@broadcom.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Add needed platform data structure and code to be able to load
the GPO child of twl6040.
Update the devicetree binding documentation at the same time.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add DT property "maxim,system-power-controller" to indicate whether the
PMIC is in charge of controlling the system power. If this is set, the
driver will provide the pm_power_off() function.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This commit adds a driver for the Avionic Design N-bit GPIO expander.
The expander provides a variable number of GPIO pins with interrupt
support.
Changes in v2:
- allow building the driver as a module
- assign of_node unconditionally
- use linear mapping IRQ domain
- properly cleanup IRQ domain
- add OF device table and annotate device tables
- emulate rising and falling edge triggers
- increase #gpio-cells to 2
- drop support for !OF
- use IS_ENABLED to conditionalize DEBUG_FS code
Changes in v3:
- make IRQ support runtime configurable (interrupt-controller property)
- drop interrupt-controller and #interrupt-cells from DT binding
- add inline to_adnp() function to wrap container_of() macro
- consistently use adnp as name for struct adnp variables
- remove irq_mask_cur and rename irq_mask to irq_enable
- fix a subtle deadlock in adnp_gpio_direction_output()
- remove dynamic allocations from debugfs code
- rename regs to num_regs to avoid confusion
- annotate non-trivial code with comments
- don't acquire mutex in adnp_gpio_get()
- assume NO_IRQ == 0
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Support for loading the twl4030 audio module via devicetree.
Sub devices for codec and vibra will be created as mfd devices once the
core MFD driver is loaded when the kernel is booted with a DT blob.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is initial device tree support for the ARM Integrator family,
we create a very basic device tree, #ifdef out the non-DT machines
when compiling for device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds Device Tree probing support to the Versatile FPGA
IRQ controller.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add regmap based syscon driver.
This is usually used for access misc bits in registers which does not belong
to a specific module, for example, IMX IOMUXC GPR and ANATOP.
With this driver, client can use generic regmap API to access registers
which are registered into syscon.
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The MAX8907 is an I2C-based power-management IC containing voltage
regulators, a reset controller, a real-time clock, and a touch-screen
controller.
The original driver was written by:
* Gyungoh Yoo <jack.yoo@maxim-ic.com>
Various fixes and enhancements by:
* Jin Park <jinyoungp@nvidia.com>
* Tom Cherry <tcherry@nvidia.com>
* Prashant Gaikwad <pgaikwad@nvidia.com>
* Dan Willemsen <dwillemsen@nvidia.com>
* Laxman Dewangan <ldewangan@nvidia.com>
During upstreaming, I (swarren):
* Converted to regmap.
* Converted to regmap-irq.
* Allowed probing from device tree.
* Renamed from max8907c->max8907, since the driver covers at least the
C and B revisions.
* General cleanup.
Signed-off-by: Gyungoh Yoo <jack.yoo@maxim-ic.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> #v3
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This resolves the merge problems with:
drivers/usb/dwc3/gadget.c
drivers/usb/musb/tusb6010.c
that had been seen in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AM33xx hwmod data and miscellaneous clock and hwmod fixes. AM33xx
should now boot on mainline after this is applied, according to
Vaibhav.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=UyqO
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-am33xx-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren:
From Paul Walmsley <paul@pwsan.com>:
AM33xx hwmod data and miscellaneous clock and hwmod fixes. AM33xx
should now boot on mainline after this is applied, according to
Vaibhav.
(The shortlog makes no sense here since it contains mostly the dependent
cleanups that are part of the preceding branches).
Signed-off-by: Olof Johansson <olof@lixom.net>
This part of the tty tree (unfortunately with all the preceding patches
as well) is a dependency for some of the OMAP cleanups, so we've pulled
it in as a dependency based on agreement with Greg.
Signed-off-by: Olof Johansson <olof@lixom.net>
This branch contains a number of fixes and cleanups to the Tegra I2C
driver related to clocks. These are based on the common clock conversion
in order to avoid duplicating the clock driver changes before and after
the conversion. Finally, a bug-fix related to I2C_M_NOSTART is included.
This branch is based on previous pull request tegra-for-3.7-common-clk.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=6+9B
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-drivers-i2c' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/drivers
From Stephen Warren:
ARM: tegra: i2c driver enhancements mostly related to clocking
This branch contains a number of fixes and cleanups to the Tegra I2C
driver related to clocks. These are based on the common clock conversion
in order to avoid duplicating the clock driver changes before and after
the conversion. Finally, a bug-fix related to I2C_M_NOSTART is included.
This branch is based on previous pull request tegra-for-3.7-common-clk.
* tag 'tegra-for-3.7-drivers-i2c' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
i2c: tegra: dynamically control fast clk
i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
ARM: tegra: clock: remove unused clock entry for i2c
ARM: tegra: clock: add connection name in i2c clock entry
i2c: tegra: pass proper name for getting clock
ARM: tegra: clock: add i2c fast clock entry in clock table
ARM: Tegra: Add smp_twd clock for Tegra20
ARM: tegra: cpu-tegra: explicitly manage re-parenting
ARM: tegra: fix overflow in tegra20_pll_clk_round_rate()
ARM: tegra: Fix data type for io address
ARM: tegra: remove tegra_timer from tegra_list_clks
ARM: tegra30: clocks: fix the wrong tegra_audio_sync_clk_ops name
ARM: tegra: clocks: separate tegra_clk_32k_ops from Tegra20 and Tegra30
ARM: tegra: Remove duplicate code
ARM: tegra: Port tegra to generic clock framework
ARM: tegra: Add clk_tegra structure and helper functions
ARM: tegra: Rename tegra20 clock file
ARM: tegra20: Separate out clk ops and clk data
ARM: tegra30: Separate out clk ops and clk data
ARM: tegra: fix U16 divider range check
...
+ sync to v3.6-rc4
Resolved remove/modify conflict in arch/arm/mach-sa1100/leds-hackkit.c
caused by the sync with v3.6-rc4.
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull in a dependent branch from Mark Brown's regulator tree for the tegra/cleanup branch.
* depends/tps6589x-dt:
regulator: tps6586x: add support for SYS rail
devicetree only. This also sets most of the frame in place necessary
to build both targets into the same image.
There's a couple of cleanups in here that are kept in this series
because they are intimately tied to the changes necessary to support
the devicetree conversions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=KXPz
-----END PGP SIGNATURE-----
Merge tag 'msm-dt-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into next/dt
From David Brown:
These patches migrate both the 8660 and 8960 targets on msm to be
devicetree only. This also sets most of the frame in place necessary
to build both targets into the same image.
There's a couple of cleanups in here that are kept in this series
because they are intimately tied to the changes necessary to support
the devicetree conversions.
By Stephen Boyd
via David Brown
* tag 'msm-dt-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: msm: Remove non-DT targets from 8960
ARM: msm: Add DT support for 8960
ARM: msm: Move io mapping prototypes to common.h
ARM: msm: Rename board-msm8x60 to signify its DT only status
ARM: msm: Make 8660 a DT only target
ARM: msm: Move 8660 to DT timer
ARM: msm: Add DT support to msm_timer
ARM: msm: Allow timer.c to compile on multiple targets
ARM: msm: Don't touch GIC registers outside of GIC code
ARM: msm: Add msm8660-surf.dts to Makefile.boot
ARM: msm: Add handle_irq handler for 8660 DT machine
Resolved trivial context conflict in arch/arm/mach-msm/io.c and a
remove/change conflict in arch/arm/mach-msm/board-msm8x60.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
This pulls in the staging tree fixes in 3.6-rc6 into our branch to resolve the
merge issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
work properly with sparse IRQ. It also removes
dependencies to mach/hardware.h. These help moving
things towards ARM single zImage support.
This branch is based on a commit in tty-next
branch with omap-devel-gpmc-fixed-for-v3.7 and
cleanup-omap-tags-for-v3.7 merged in to keep things
compiling and sort out some merge conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GLSh
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-sparseirq-for-v3.7' into devel-dt
This branch contains changes needed to make omap2+
work properly with sparse IRQ. It also removes
dependencies to mach/hardware.h. These help moving
things towards ARM single zImage support.
This branch is based on a commit in tty-next
branch with omap-devel-gpmc-fixed-for-v3.7 and
cleanup-omap-tags-for-v3.7 merged in to keep things
compiling and sort out some merge conflicts.
Conflicts:
arch/arm/mach-omap2/omap4-common.c
drivers/gpio/gpio-twl4030.c
Conflicts:
net/netfilter/nfnetlink_log.c
net/netfilter/xt_LOG.c
Rather easy conflict resolution, the 'net' tree had bug fixes to make
sure we checked if a socket is a time-wait one or not and elide the
logging code if so.
Whereas on the 'net-next' side we are calculating the UID and GID from
the creds using different interfaces due to the user namespace changes
from Eric Biederman.
Signed-off-by: David S. Miller <davem@davemloft.net>
IFM O2D cameras use special sensor bus interface glue-logic to
connect camera sensors to mpc5200 LocalPlus bus. Add device tree
bindings documentation for it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add DT property "ti,system-power-controller" telling whether or not this
pmic is in charge of controlling the system power, so the power off
routine can be hooked up to system call "pm_power_off".
Based on the work by:
Dan Willemsen <dwillemsen@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
