Initial support for VCE 1.0 using newest firmware.
v2: rebased
v3: fix for TN
v4: fix FW size calculation
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For setting clocks with VCE v1.0
v2: (chk) rebased on current tree
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
They seem to work fine with the kernel interface.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Previously we were completely over allocating, fix this
by actually implementing the size calculation.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Userspace will be able to tell whether a GPU reset occured by comparing
an old referece value of the counter with a new value.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Atomic modesetting: now with modesetting support.
v2: Moved drm_atomic_set_mode_prop_for_crtc from previous patch; removed
state->active fiddling, documented return code. Changed property
type to DRM_MODE_PROP_BLOB.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Tested-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a blob property tracking the current mode to the CRTC state, and
ensure it is properly updated and referenced.
v2: Continue using crtc_state->mode inside getcrtc, instead of reading
out the mode blob. Use IS_ERR and PTR_ERR from create_blob. Move
set_mode_prop_for_crtc to later patch where it actually gets used.
Enforce !!state->enable == !!state->mode_blob inside
drm_atomic_crtc_check.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Tested-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a new helper, to be used later for blob property management, that
sets the mode for a CRTC state, as well as updating the CRTC enable/active
state at the same time.
v2: Do not touch active/mode_changed in CRTC state. Document return
value. Remove stray drm_atomic_set_mode_prop_for_crtc declaration.
v3: Remove i915 changes, and leave it directly bashing crtc_state->mode
for the meantime.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Tested-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Unfortunately old userspace didn't clear this properly, but since
we've added fb modifiers that's fixed. Checking properly that unused
fields is important for abi extensions, and just right now there's a
bunch of discussions going on about how exactly the additional aux
planes for render compression should be specified.
So let's first make sure that the values in those additional fields
can be indeed used.
Cc: Thierry Reding <thierry.reding@gmail.com>
Testcase: igt/kms_addfb/unused-*
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
When we look up a blob property, make sure we retain a reference to the
blob for the lifetime.
v2: Use DRM_MODE_PROP_BLOB, not PROP_OBJECT + OBJECT_BLOB.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Tested-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For actual sharing of buffers with other drivers (ie. actual hardware)
we'll need to pimp things out a bit better to deal w/ caching, multiple
memory domains, etc. See thread:
http://lists.freedesktop.org/archives/dri-devel/2015-May/083160.html
But for the llvmpipe use-case this isn't a problem. Nor do we really
need prime/dri3 (dri2 is sufficient). So until the other issues are
sorted lets remove DRIVER_PRIME.
v2: also drop the dead code
[airlied:
Okay I'm convinced this API could have a lot of use cases
that are really really bad, yes the upload use case is valid
however that isn't the only use case enabled, and if we allow
all the other use cases, people will start to (ab)use them,
and then they'll be ABI and my life will get worse, so disable
PRIME for now]
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit 118182e9d7.
It's causing too much trouble when compile-testing for non-i915 folks.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
If we have more than one CRTCs in a group pre-associate planes 0-3 with
CRTC 0 and planes 4-7 with CRTC 1 to minimize flicker occurring when the
association is changed. The pre-association could be controlled by a
module parameter if needed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The number of CRTCs in a group is only used to implement plane
initialization for now, but is also needed to implement pre-association
of planes to CRTCs. Store it in the group structure instead of computing
it on demand.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Hardware planes are driven by the timing generator of the CRTC they are
associated to. Changing the association requires restarting the CRTC
group that the plane belongs to, resulting in flicker on the other CRTC.
To avoid flicker as much as possible, try to allocate planes first from
the free planes already associated with the target CRTC. If allocation
fails then fall back to allocation from all free planes.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Changing the plane to CRTC associations requires restarting the CRTC
group, creating visible flicker. Mitigate the issue by changing plane
association only when a plane becomes enabled, not when it get disabled.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Plane allocation is a complex process, add debugging statements to help
finding out what could might wrong.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
All other cast functions are named without using "du", make the plane
state cast consistent with them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The rcar_du_planes structure contains a single field and is only
instantiated in the rcar_du_group structure. Embed it directly and
remove the rcar_du_planes structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The plane property objects are instantiated once per CRTC group, while
they should be instantiated once globally for the device. Fix this and
move them to the rcar_du_device structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The ADV7511 is probed before its slave encoder init function associates
it with an encoder. This creates a time window during which hot plug
detection interrupts can occur with an encoder, resulting in a crash in
the IRQ handler.
Fix this by ignoring hot plug detection IRQs when no encoder is
associated yet.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Add an ioctl which allows users to create blob properties from supplied
data. Currently this only supports modes, creating a drm_display_mode from
the userspace drm_mode_modeinfo.
v2: Removed size/type checks.
Rebased on new patches to allow error propagation from create_blob,
as well as avoiding double-allocation.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@intel.com>
Tested-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Change drm_property_create_blob to return an ERR_PTR-encoded error on
failure, so we can pass the failure reason down.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Cc: Maarten Lankhorst <maarten.lankhorst@intel.com>
Tested-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make the data parameter to drm_property_create_blob optional; if
omitted, the copy will be skipped and the data will be empty.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@intel.com>
Tested-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the drm_display_mode <-> drm_mode_modeinfo conversion functions
from drm_crtc.c to drm_modes.c, and make them non-static so that others
can use them.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Tested-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The only user of convert_umode was also performing mode validation, so
do that in the same place.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Tested-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather than open-coding our own CRTC state helpers, use the atomic helpers
added in f5e7840b0c, and make our freeing behaviour consistent as well.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Tested-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Change '@param foo' to '@foo:' to fit kerneldoc style.
672cb1d6ae mistakenly added an extra parameter to the kerneldoc for
drm_property_unreference_blob which wasn't actually present.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As Daniel commented on
commit b7ffe1362c5f468b853223acc9268804aa92afc8
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Apr 27 13:41:24 2015 +0100
drm/i915: Free RPS boosts for all laggards
it is better to be explicit when sharing hardcoded values such as
throttle/boost timeouts. Make it so!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After allocating from the slab cache, we then need to free the request
back into the slab cache upon error (and not call kfree as that leads
to eventual memory corruption).
Fixes regression from
commit efab6d8dd1
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Apr 7 16:20:57 2015 +0100
drm/i915: Use a separate slab for requests
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is a mplayer video failure reported with xv.
This is because there is a request to do both plane scaling
and colorkey. Because skl hw doesn't support plane scaling
and colorkey at the same time, request is failed which is expected
behavior.
To make xv operate, this patch allows colorkey continue to work
without using scaler. Then behavior would be similar to platforms
without plane scaler support.
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90449
[danvet: change can_scale to bool as requested by Ville.]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GTT caching was disabled by default on gen8 due to not working with
big pages. Some information suggests that it got fixed, but still
GTT caching has been left disabled by default. Or could be it just
meant that the default was changed to off, and hence the problem
got solved.
Enable GTT caching in the hopes of some performance increase.
Whether or not the big pages issue has been fixed is irrelevant
at this stage since we don't use big pages.
This gives me a 1-2% improvement in xonotic on my BSW. Haven't tried
BDW, but supposedly it has larger TLBs so might not benefit as much.
On HSW GTT caching is enabled by default.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GEN8_L3SQCREG1 isn't saved in the context (verified by going through
a context dump), and so we shouldn't be using the ring w/a code to
initialize it. Also Bspec explicitly talks about MMIO and writing it
with the CPU.
Additionally there's another w/a WaTempDisableDOPClkGating:bdw which
tells us to disable DOP clock gating around the GEN8_L3SQCREG1 write
to make sure everyone notices the change. So let's do that as well.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're not using ilk_init_lp_watermarks() on BDW for some reason.
Probably due to the BDW patches and the relevant WM patches landing
roughlly at the same time. Fix it up.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In
commit f02ad907cd
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jan 22 16:36:23 2015 +0100
drm/atomic-helpers: Recover full cursor plane behaviour
we've added a hack to atomic helpers to never to vblank waits for
cursor updates through the legacy apis since that's what X expects.
Unfortunately we've (again) forgotten to adjust the transitional
helpers. Do this now.
This fixes regressions for drivers only partially converted over to
atomic (like i915).
Reported-by: Pekka Paalanen <ppaalanen@gmail.com>
Cc: Pekka Paalanen <ppaalanen@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-and-tested-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Just two small DP fixes for 4.1
* 'drm-fixes-4.1' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix error flag checking in native aux path
drm/radeon: retry dcpd fetch
There's a stable backport from Ander [1] that combines this and a few
other commits to fix the flickering on v4.0, reported in [2] among
others. Having this upstream is obviously a requirement for stable.
* tag 'drm-intel-fixes-2015-05-21' of git://anongit.freedesktop.org/drm-intel:
drm/i915: fix screen flickering
Bspec says we should disable the FDI RX/TX before disabling the PCH
ports. Do so.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Follow the BSpec sequence for the CRT port as well on PCH platforms,
ie. disable the pipe before the port.
Didn't bother looking at DDI in detail yet, so leave that one be even
though the CRT is a PCH port there.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While at it also remove the redundant/unneeded w/a like done for hdmi
already.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Mention that this also removes the unneeded w/a, as suggested
by Jesse.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BSpec says we should disable all ports after the pipe on PCH
platforms. Do so. Fixes a pipe off timeout on ILK now caused by
the transcoder B workaround.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently the IBX transcoder B workarounds are not working correctly.
Well, the HDMI one seems to be working somewhat, but the DP one is
definitely busted.
After a bit of experimentation it looks like the best way to make this
work is first disable the port on transcoder B, and then re-enable it
transcoder A, and immediately disable it again.
We can also clean up the code by noting that we can't be called without
a valid crtc. And also note that port A on ILK does not need the
workaround, so let's check for that one too.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On IBX the SDVO/HDMI register write may be masked when enabling the
port, so it may need to written twice. The HDMI code does this, but
the SDVO code does not. Add the workaround to the SDVO code as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
