Cleanup code to make it more clean and readable.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Occasionally, the PHY can be initially inaccessible when the first read of
a PHY register, e.g. PHY_ID1, happens (signified by the returned value
0xFFFF) but subsequent accesses of the PHY work as expected. Add a retry
counter similar to how it is done in the generic e1000_get_phy_id().
Also, when the PHY is completely inaccessible (i.e. when subsequent reads
of the PHY_IDx registers returns all F's) and the MDIO access mode must be
set to slow before attempting to read the PHY ID again, the functions that
do these latter two actions expect the SW/FW/HW semaphore is not already
set so the semaphore must be released before and re-acquired after calling
them otherwise there is an unnecessarily inordinate amount of delay during
device initialization.
Reported-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
SYNCH bit and IV bit of RXCW register are sticky. Before examining these bits,
RXCW should be read twice to filter out one-time false events and have correct
values for these bits. Incorrect values of these bits in link check logic can
cause weird link stability issues if auto-negotiation fails.
CC: stable <stable@vger.kernel.org> [2.6.38+]
Reported-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Apple Thunderbolt ethernet device is already listed in the driver,
but not hooked up in the MODULE_DEVICE_TABLE(). This fixes that and
allows it to work properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After FW download, activate new FW by invoking FW reset.
Recreate rings once new FW is operational.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Invoke only required initialization routines for Lancer.
Remove invocation of unnecessary routines.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Query die temperature stat for Lancer to report it correctly
in ethtool.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Autonegotiation of pause parameters is possible only on some PHYs.
Ability of autoneg of pause parameters is reported by adapter.
Autoneg of pause parameters cannot be changed from driver.
Fix driver to give error when autoneg mode is toggled by user.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First update the adapter variables with the current speed and
mode before fire the notification. Otherwise, the get_settings()
may provide old values.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Acked-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of older ColdFire CPU based boards use NS8390 based network
controllers. Most use the Davicom 9008F or the UMC 9008F. This driver
provides the support code to get these devices working on these platforms.
Generally the NS8390 based eth device is direct connected via the general
purpose bus of the ColdFire CPU. So its addressing and interrupt setup is
fixed on each of the different platforms (classic platform setup).
This driver is based on the other drivers/net/ethernet/8390 drivers, and
includes the lib8390.c code. It uses the existing definitions of the
board NS8390 device addresses, interrupts and access types from the
arch/m68k/include/asm/mcf8390.h, but moves the IO access functions into
the driver code and out of that header.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow easy paravirtualization of P_Key and GID table sizes, keep
paravirtualized sizes in mlx4_dev->caps, but save the actual physical
sizes from FW in struct: mlx4_dev->phys_cap.
In addition, in SR-IOV mode, do the following:
1. Reduce reported P_Key table size by 1.
This is done to reserve the highest P_Key index for internal use,
for declaring an invalid P_Key in P_Key paravirtualization.
We require a P_Key index which always contain an invalid P_Key
value for this purpose (i.e., one which cannot be modified by
the subnet manager). The way to do this is to reduce the
P_Key table size reported to the subnet manager by 1, so that
it will not attempt to access the P_Key at index #127.
2. Paravirtualize the GID table size to 1. Thus, each guest sees
only a single GID (at its paravirtualized index 0).
In addition, since we are paravirtualizing the GID table size to 1, we
add paravirtualization of the master GID event here (i.e., we do not
do ib_dispatch_event() for the GUID change event on the master, since
its (only) GUID never changes).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Modify mlx4_dev_cap to allow IB support when SR-IOV is active. Modify
mlx4_slave_cap to set the "rdma-supported" bit in its flags area, and
pass that to the guests (this is done in QUERY_FUNC_CAP and its
wrapper).
However, we don't activate IB support quite yet -- we leave the error
return at the start of mlx4_ib_add in the mlx4_ib driver.
In addition, set "protected fmr supported" bit to zero in the
QUERY_FUNC_CAP wrapper.
Finally, in the QUERY_FUNC_CAP wrapper, we needed to add code which
checks for the port type (IB or Ethernet). Previously, this was not
an issue, since only Ethernet ports were supported.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The SR-IOV special QP tunneling mechanism uses proxy special QPs
(instead of the real special QPs) for MADs on guests. These proxy QPs
send their packets to a "tunnel" QP owned by the master. The master
then forwards the MAD (after any required paravirtualization) to the
real special QP, which sends out the MAD.
For security reasons (i.e., to prevent guests from sending MADs to
tunnel QPs belonging to other guests), each proxy-tunnel QP pair is
assigned a unique, reserved, Q_Key. These Q_Keys are available only
for proxy and tunnel QPs -- if the guest tries to use these Q_Keys
with other QPs, it will fail.
This patch introduces a mechanism for reserving a block of 64K Q_Keys
for proxy/tunneling use.
The patch introduces also two new fields into mlx4_dev: base_sqpn and
base_tunnel_sqpn.
In SR-IOV mode, the QP numbers for the "real," proxy, and tunnel sqps
are added to the reserved QPN area (so that they will not change).
There are 8 special QPs per port in the HCA, and each of them is
assigned both a proxy and a tunnel QP, for each VF and for the PF as
well in SR-IOV mode.
The QPNs for these QPs are arranged as follows:
1. The real SQP numbers (8)
2. The proxy SQPs (8 * (max number of VFs + max number of PFs)
3. The tunnel SQPs (8 * (max number of VFs + max number of PFs)
To support these QPs, two new fields are added to struct mlx4_dev:
base_sqp: this is the QP number of the first of the real SQPs
base_tunnel_sqp: this is the qp number of the first qp in the tunnel
sqp region. (On guests, this is the first tunnel
sqp of the 8 which are assigned to that guest).
In addition, in SR-IOV mode, sqp_start is the number of the first
proxy SQP in the proxy SQP region. (In guests, this is the first
proxy SQP of the 8 which are assigned to that guest)
Note that in non-SR-IOV mode, there are no proxies and no tunnels.
In this case, sqp_start is set to sqp_base -- which minimizes code
changes.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In mlx4_init_icm_table(), free the allocated table if we failed to
allocate memory to its entries.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Spotted four duplicate declarations in icm.h, remove them.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There are really only 3 modes that can control the number of queues. Those
are RSS, DCB, and VMDq/SR-IOV. Currently we have things much more broken
up than they need to be for how we are configuring the rings. In order to
try and straiten some of this out I am going to start merging similar
functionality into single functions. To start with I am merging the Flow
Director ring configuration into the RSS ring configuration since Flow
Director cannot function with DCB or SR-IOV.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch replaces a switch statement for an 82598 workaround with an if
statement that only applies to 82598. In addition I am pulling out several
dead pieces of code and instead of reading the SRRCTL register and then
modifying it we are just writing a value which we generate from scratch.
Finally I am also removing any drop enable related code since that was
moved to a function of its own.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The mask value for ring features was overloaded for FCoE which can lead to
some confusion. In order to avoid any confusion I am splitting the mask
value and adding an offset value. This can be used for the start of the
FCoE rings, and in the future I hope to use it to store the start of the
registers for SR-IOV.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We are currently using indices to indicate the upper limit on a ring
feature. However since we can switch back and forth on features such as
DCB and that has effects on other features such as RSS it is preferable to
instead store the upper limit separate from the current value for the
number of rings related to the feature.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It makes much more sense for us to count q_vectors instead of MSI-X
vectors. We were using num_msix_vectors to find the number of q_vectors in
multiple places. This was wasteful since we only had one place that
actually needs the number of MSI-X vectors and that is in slow path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit 6d29b1ef introduces a bug, ntohs is __be16_to_cpu,
not cpu_to_be16.
We always use htons on IP_OFFSET and IP_MF, then compare
with network package.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETH_P_IP is host Endian, skb->protocol is big Endian, when
compare them, Using htons on skb->protocol is wrong.
And fix two code style issues: indentation and remove
unnecessary parentheses.
CC: Tristram Ha <Tristram.Ha@micrel.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
CC: Joe Perches <joe@perches.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/batman-adv/bridge_loop_avoidance.c
net/batman-adv/bridge_loop_avoidance.h
net/batman-adv/soft-interface.c
net/mac80211/mlme.c
With merge help from Antonio Quartulli (batman-adv) and
Stephen Rothwell (drivers/net/usb/qmi_wwan.c).
The net/mac80211/mlme.c conflict seemed easy enough, accounting for a
conversion to some new tracing macros.
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare cases, bnx2x_free_tx_skbs() can unmap the wrong DMA address
when it gets to the last entry of the tx ring. We were not using
the proper macro to skip the last entry when advancing the tx index.
Reported-by: Zongyun Lai <zlai@vmware.com>
Reviewed-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Missing case was causing ethtool self test to print garbage
value in extra info section.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX queue was being stopped at beginning of send path instead
of at the end when last descriptor is used.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling RX cut-thru mode yields better performance as received frames
start getting written to memory before a whole frame is received.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase the number of outstanding read and write AXI transactions from 1
to 8 for better performance.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix intermittent hangs in xgmac_rx_refill. If a ring buffer entry already
had an skb allocated, then xgmac_rx_refill would get stuck in a loop. This
can happen on a rx error when we just leave the skb allocated to the entry.
[ 7884.510000] INFO: rcu_preempt detected stall on CPU 0 (t=727315 jiffies)
[ 7884.510000] [<c0010a59>] (unwind_backtrace+0x1/0x98) from [<c006fd93>] (__rcu_pending+0x11b/0x2c4)
[ 7884.510000] [<c006fd93>] (__rcu_pending+0x11b/0x2c4) from [<c0070b95>] (rcu_check_callbacks+0xed/0x1a8)
[ 7884.510000] [<c0070b95>] (rcu_check_callbacks+0xed/0x1a8) from [<c0036abb>] (update_process_times+0x2b/0x48)
[ 7884.510000] [<c0036abb>] (update_process_times+0x2b/0x48) from [<c004e8fd>] (tick_sched_timer+0x51/0x94)
[ 7884.510000] [<c004e8fd>] (tick_sched_timer+0x51/0x94) from [<c0045527>] (__run_hrtimer+0x4f/0x1e8)
[ 7884.510000] [<c0045527>] (__run_hrtimer+0x4f/0x1e8) from [<c0046003>] (hrtimer_interrupt+0xd7/0x1e4)
[ 7884.510000] [<c0046003>] (hrtimer_interrupt+0xd7/0x1e4) from [<c00101d3>] (twd_handler+0x17/0x24)
[ 7884.510000] [<c00101d3>] (twd_handler+0x17/0x24) from [<c006be39>] (handle_percpu_devid_irq+0x59/0x114)
[ 7884.510000] [<c006be39>] (handle_percpu_devid_irq+0x59/0x114) from [<c0069aab>] (generic_handle_irq+0x17/0x2c)
[ 7884.510000] [<c0069aab>] (generic_handle_irq+0x17/0x2c) from [<c000cc8d>] (handle_IRQ+0x35/0x7c)
[ 7884.510000] [<c000cc8d>] (handle_IRQ+0x35/0x7c) from [<c033b153>] (__irq_svc+0x33/0xb8)
[ 7884.510000] [<c033b153>] (__irq_svc+0x33/0xb8) from [<c0244b06>] (xgmac_rx_refill+0x3a/0x140)
[ 7884.510000] [<c0244b06>] (xgmac_rx_refill+0x3a/0x140) from [<c02458ed>] (xgmac_poll+0x265/0x3bc)
[ 7884.510000] [<c02458ed>] (xgmac_poll+0x265/0x3bc) from [<c029fcbf>] (net_rx_action+0xc3/0x200)
[ 7884.510000] [<c029fcbf>] (net_rx_action+0xc3/0x200) from [<c0030cab>] (__do_softirq+0xa3/0x1bc)
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix net tx watchdog timeout recovery. The descriptor ring was reset,
but the DMA engine was not reset to the beginning of the ring.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->dev is being unnecessarily set by the driver on packet recieve.
eth_type_trans already sets skb->dev to the proper value and it is not
referenced anywhere else in the dirver, thus making its setting unnecessary.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->dev is being unnecessarily set during ring init and skb alloc in rx. It is
already being set to the proper value when eth_type_trans is called on packet
receive, and the skb->dev is not referenced anywhere else in the code.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->dev is being unnecessarily set by the driver's skb alloc routine (which is
called in init and during rx). It is already being set to the proper value when
eth_type_trans is called on packet receive, and the skb->dev is not referenced
anywhere else in the code.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->dev is being unnecessarily set during ring init and skb alloc in rx. It is
already being set to the proper value when eth_type_trans is called on packet
receive, and the skb->dev is not referenced anywhere else in the code.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->dev is being unnecessarily set by the driver on packet recieve.
eth_type_trans already sets skb->dev to the proper value and it is not
referenced anywhere else in the dirver, thus making its setting unnecessary.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Cc: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Cc: Ron Mercer <ron.mercer@qlogic.com>
Cc: linux-driver@qlogic.com
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->dev is being unnecessarily set before calling eth_type_trans.
eth_type_trans already sets skb->dev to the proper value, thus making this
unnecessary.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: linux-driver@qlogic.com
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->dev is being unnecessarily set during ring init. It is already being set
to the proper value when eth_type_trans is called on packet receive, and the
skb->dev is not referenced anywhere else in the code.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->dev is being unnecessarily set before calling eth_type_trans.
eth_type_trans already sets skb->dev to the proper value, thus making this
unnecessary.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
