Have the netlink per-protocol optional bind function return an int error code
rather than void to signal a failure.
This will enable netlink protocols to perform extra checks including
capabilities and permissions verifications when updating memberships in
multicast groups.
In netlink_bind() and netlink_setsockopt() the call to the per-protocol bind
function was moved above the multicast group update to prevent any access to
the multicast socket groups before checking with the per-protocol bind
function. This will enable the per-protocol bind function to be used to check
permissions which could be denied before making them available, and to avoid
the messy job of undoing the addition should the per-protocol bind function
fail.
The netfilter subsystem seems to be the only one currently using the
per-protocol bind function.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicity and simplify code flow by moving the rcu_read_unlock() above
the condition and let the flow control exit naturally at the end of the
function.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a new ancillary load (bpf call in eBPF parlance) that produces
a 32-bit random number. We are implementing it as an ancillary load
(instead of an ISA opcode) because (a) it is simpler, (b) allows easy
JITing, and (c) seems more in line with generic ISAs that do not have
"get a random number" as a instruction, but as an OS call.
The main use for this ancillary load is to perform random packet sampling.
Signed-off-by: Chema Gonzalez <chema@google.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if allocating memory for vlan_pcpu_stats failed, the device can not be operated
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This be2net patch implements the get/set_rxfh() ethtool hooks.
RSS_CONFIG device command is invoked to set hashkey and indirection table.
It also uses an initial random value for RSS hash key instead of a
hard-coded value as hard-coded values for a hash-key are usually
considered a security risk.
Signed-off-by: Venkat Duvvuru <VenkatKumar.Duvvuru@Emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This ethtool patch primarily copies the ioctl command data structures
from/to the User space and invokes the driver hook.
Signed-off-by: Venkat Duvvuru <VenkatKumar.Duvvuru@Emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 0e280af026 ("tcp: introduce TCPSpuriousRtxHostQueues SNMP
counter") we added a logic to detect when a packet was retransmitted
while the prior clone was still in a qdisc or driver queue.
We are now confident we can do better, and catch the problem before
we fragment a TSO packet before retransmit, or in TLP path.
This patch fully exploits the logic by simply canceling the spurious
retransmit.
Original packet is in a queue and will eventually leave the host.
This helps to avoid network collapses when some events make the RTO
estimations very wrong, particularly when dealing with huge number of
sockets with synchronized blast.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Userspace applications can use IFA_F_MANAGETEMPADDR with RTM_NEWADDR
already to indicate that the kernel should take care of temporary
address management.
This patch adds related functionality to RTM_DELADDR. By setting
IFA_F_MANAGETEMPADDR a userspace application can indicate that the kernel
should delete all related temporary addresses as well.
A corresponding patch for the "ip addr del" command has been applied to
iproute2 already.
Signed-off-by: Heiner Kallweit <heiner.kallweit@web.de>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A label just before a brace needs a following semicolon (empty statement).
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SMC_DEBUG >= 2, we hit the following compilation error:
drivers/net/ethernet/smsc/smc91x.c:85:0:
drivers/net/ethernet/smsc/smc91x.c: In function ‘smc_findirq’:
drivers/net/ethernet/smsc/smc91x.c:1784:9: error: ‘dev’ undeclared (first use in this function)
DBG(2, dev, "%s: %s\n", CARDNAME, __func__);
^
Fix it by passing in the appropriate netdev pointer.
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ying Xue says:
====================
purge tipc_net_lock
Now tipc routing hierarchy comprises the structures 'node', 'link'and
'bearer'. The whole hierarchy is protected by a big read/write lock,
tipc_net_lock, to ensure that nothing is added or removed while code
is accessing any of these structures. Obviously the locking policy
makes node, link and bearer components closely bound together so that
their relationship becomes unnecessarily complex. In the worst case,
such locking policy not only has a negative influence on performance,
but also it's prone to lead to deadlock occasionally.
In order o decouple the complex relationship between bearer and node
as well as link, the locking policy is adjusted as follows:
- Bearer level
RTNL lock is used on update side, and RCU is used on read side.
Meanwhile, all bearer instances including broadcast bearer are
saved into bearer_list array.
- Node and link level
All node instances are saved into two tipc_node_list and node_htable
lists. The two lists are protected by node_list_lock on write side,
and they are guarded with RCU lock on read side. All members in node
structure including link instances are protected by node spin lock.
- The relationship between bearer and node
When link accesses bearer, it first needs to find the bearer with
its bearer identity from the bearer_list array. When bearer accesses
node, it can iterate the node_htable hash list with the node address
to find the corresponding node.
In the new locking policy, every component has its private locking
solution and the relationship between bearer and node is very simple,
that is, they can find each other with node address or bearer identity
from node_htable hash list or bearer_list array.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a21a584d67 (tipc: fix neighbor
detection problem after hw address change) introduces a race condition
involving tipc_disc_delete() and tipc_disc_add/remove_dest that can
cause TIPC to dereference the pointer to the bearer discovery request
structure after it has been freed since a stray pointer is left in the
bearer structure.
In order to fix the issue, the process of resetting the discovery
request handler is optimized: the discovery request handler and request
buffer are just reset instead of being freed, allocated and initialized.
As the request point is always valid and the request's lock is taken
while the request handler is reset, the race doesn't happen any more.
Reported-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The node map variable - 'nodes' in bearer structure is only used by
bclink. When bclink accesses it, bc_lock is held. But when change it,
for instance, in tipc_bearer_add_dest() or tipc_bearer_remove_dest()
the bc_lock is not taken at all. To avoid any inconsistent data, we
should always grab bc_lock while accessing node map variable.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As bearer pointer is known in tipc_l2_device_event(), it's unnecessary
to search it again in tipc_disable_bearer(). If tipc_disable_bearer()
is replaced with bearer_disable() in tipc_l2_device_event(), this will
help us save a bit time when bearer is disabled.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'media_ptr' pointer in bearer structure which points to network
device, is protected by RCU. So, before netdevice is released,
synchronize_net() should be involved to prevent no any user of
the netdevice on read side from accessing it after it is freed.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now tipc routing hierarchy comprises the structures 'node', 'link'and
'bearer'. The whole hierarchy is protected by a big read/write lock,
tipc_net_lock, to ensure that nothing is added or removed while code
is accessing any of these structures. Obviously the locking policy
makes node, link and bearer components closely bound together so that
their relationship becomes unnecessarily complex. In the worst case,
such locking policy not only has a negative influence on performance,
but also it's prone to lead to deadlock occasionally.
In order o decouple the complex relationship between bearer and node
as well as link, the locking policy is adjusted as follows:
- Bearer level
RTNL lock is used on update side, and RCU is used on read side.
Meanwhile, all bearer instances including broadcast bearer are
saved into bearer_list array.
- Node and link level
All node instances are saved into two tipc_node_list and node_htable
lists. The two lists are protected by node_list_lock on write side,
and they are guarded with RCU lock on read side. All members in node
structure including link instances are protected by node spin lock.
- The relationship between bearer and node
When link accesses bearer, it first needs to find the bearer with
its bearer identity from the bearer_list array. When bearer accesses
node, it can iterate the node_htable hash list with the node
address to find the corresponding node.
In the new locking policy, every component has its private locking
solution and the relationship between bearer and node is very simple,
that is, they can find each other with node address or bearer identity
from node_htable hash list or bearer_list array.
Until now above all changes have been done, so tipc_net_lock can be
removed safely.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the media_ptr pointer is protected with tipc_net_lock write lock
on write side; tipc_net_lock read lock is used to read side. As the
part of effort of eliminating tipc_net_lock, we decide to adjust the
locking policy of media_ptr pointer protection: on write side, RTNL
lock is use while on read side RCU read lock is applied.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently on both paths of message transmission and reception, the
read lock of tipc_net_lock must be held before bearer is accessed,
while the write lock of tipc_net_lock has to be taken before bearer
is configured. Although it can ensure that bearer is always valid on
the two data paths, link and bearer is closely bound together.
So as the part of effort of removing tipc_net_lock, the locking
policy of bearer protection will be adjusted as below: on the two
data paths, RCU is used, and on the configuration path of bearer,
RTNL lock is applied.
Now RCU just covers the path of message reception. To make it possible
to protect the path of message transmission with RCU, link should not
use its stored bearer pointer to access bearer, but it should use the
bearer identity of its attached bearer as index to get bearer instance
from bearer_list array, which can help us decouple the relationship
between bearer and link. As a result, bearer on the path of message
transmission can be safely protected by RCU when we access bearer_list
array within RCU lock protection.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert bearer_list to RCU list. It's protected by RTNL lock on
update side, and RCU read lock is applied to read side.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the tipc network initialization(ie, tipc_net_start routine) is
under RTNL protection, its corresponding deinitialization part(ie,
tipc_net_stop routine) should be protected by RTNL too.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the 'tipc_ptr' pointer is protected by tipc_net_lock
write lock on write side, and RCU read lock is applied to read
side. In addition, there have two paths on write side where we
may change variables pointed by the 'tipc_ptr' pointer: one is
to configure bearer by tipc-config tool and another one is that
bearer status is changed by notification events of its attached
interface. But on the latter path, we improperly deem that
accessing 'tipc_ptr' pointer happens on read side with
rcu_read_lock() although some variables pointed by the 'tipc_ptr'
pointer are changed possibly.
Moreover, as now the both paths are guarded by RTNL lock, it's
better to adjust the locking policy of 'tipc_ptr' pointer
protection, allowing RTNL instead of tipc_net_lock write lock to
protect it on write side, which will help us purge tipc_net_lock
in the future.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There have two paths where we can configure or change bearer status:
one is that bearer is configured from user space with tipc-config
tool; another one is that bearer is changed by notification events
from its attached interface. On the first path, one dedicated
config_mutex lock is guarded; on the latter path, RTNL lock has been
placed to serialize the process of dealing with interface events.
So, if RTNL lock is also used to protect the first path, this will
not only extremely help us simplify current locking policy, but also
config_mutex lock can be deleted as well.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds phy_found error path when there is no phy device
and changes bus_name.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves cksum_ctl to tx_rd_des23 from cksum_pktlen for correct checksum
offloading and modifies size for Tx/Rx descriptor.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Execute "ethtool -L eth0 combined 0" in guest, if multiqueue
is enabled, virtnet_send_command() will return -EINVAL error,
there is a validation in QEMU.
But if multiqueue is disabled, virtnet_set_queues() will just
return zero (success). We should return error for this situation.
Signed-off-by: Amos Kong <akong@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC address retrieved from dt was not actually written to the
hardware. This meant proper communication was only possible after
changing the MAC address.
Fix that by always writing the mac address during probing.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the first step to remove leftover code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've implemented table calculation, but forgot to enable writing it in
power setup function.
By the way document table layout.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Logic in specs and our code was wrong. Init and calibration values for
newer cards depend on radio revision, not PHY revision.
To make code clearer, change tables names to include "radio" or "phy".
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They were extracted from MMIO dumps of 14e4:4353 and wl 6.30.223.141.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bit 0x200 has been noticed in the following log:
radio_read(0x02ca) -> 0x0000
radio_write(0x00ca) <- 0x0080
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New Broadcom drivers don't upload it anymore. It was probably a copy & paste
mistake in early N-PHY rev 3+ days.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently AMSDU and AMPDU aggregation is enabled for TID 0 to
TID 5 streams. Lets enable it for remaining two streams also.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will help to aggregate more packets which yields better
throughput results for 11ac chipsets.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will help to aggregate more packets which yields better
throughput results.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware dump feature is added for PCIe based chipsets.
Separate file will be created at /var/log/fw_dump_*
for each memory segment.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This option be useful to dump firmware memory for debugging
purpose. Actual code to dump firmware momory for SDIO and PCIe
chipsets will be added later.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After changing local per interface beacon setting restore original
global beaconing state.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When command timeout occurs due to a firmware/hardware bug,
there is no chance of next command being successful. We will
keep cmd_sent flag on so that next command won't be sent to
firmware.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IE's are parsed from beacon buffer and stored locally using
mwifiex_update_bss_desc_with_ie() function.
Sometimes the local pointers point to the data inside IE, but
while using them it is assumed that they are pointing to the IE
itself.
These issues are fixed in this patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'add_remove_card_sem' semaphore already takes care of
synchronization for driver load and unload threads.
Hence there won't be a case when unload thread is waiting on
'wait_for_completion(fw_load)'.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This option allows driver to finish pending operations in
disconnect handler by not killing URBs after usb_deregister
call.
We will get rid of global pointer 'usb_card' by moving code
from cleanup_module() to disconnect(). This will help to match
with our handling for SDIO and PCIe interfaces.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New skbs are allocated at the time of AMSDU aggregation. Setting
up in timestamps for such skbs was missing which would result
into wrong queue delays passed to FW. Fix this by setting
timestamp of skbs created for AMSDU aggregation.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
