This acts as a reversion of 1c6b2ca5e0 in
the case of UP SH-4, where we still have the risk of a multiple hit
between the slow and fast paths. As seen on SH7780.
Signed-off-by: Hideo Saito <saito@densan.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use generic_io_base to point out the pci io window, and make sure the
highest port address used is SH7751_PCI_IO_SIZE - 1.
This patch fixes pci io port access for the r2d boards - CONFIG_8139TOO_PIO
now works as expected. So does the alsa driver for CMI8738.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Katsuya MATSUBARA <matsu@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch makes sure ctrl_inN/outN are used instead of inN/outN for on chip
pci registers. Without this patch addresses may be adjusted using the value
in generic_io_base. This patch makes it possible to set generic_io_base and
have pci without reading and writing all over the place.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Katsuya MATSUBARA <matsu@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously this took an explicit range, update this to use the same
behaviour as the rest of the SH parts where we simply flush out a line
from the start address.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds sh7366 cpu supports. Just the most basic things like interrupt
controller, clocks and serial port are included at this point.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes the maskreg irq code since it is not in use anymore.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the highlander CF device from good old machvec readb/writeb
to the new shiny trapped io.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the CF device on r2d boards from machvec readb/writeb
to trapped io.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The idea is that we want to get rid of the in/out/readb/writeb callbacks from
the machvec and replace that with simple inline read and write operations to
memory. Fast and simple for most hardware devices (think pci).
Some devices require special treatment though - like 16-bit only CF devices -
so we need to have some method to hook in callbacks.
This patch makes it possible to add a per-device trap generating filter. This
way we can get maximum performance of sane hardware - which doesn't need this
filter - and crappy hardware works but gets punished by a performance hit.
V2 changes things around a bit and replaces io access callbacks with a
simple minimum_bus_width value. In the future we can add stride as well.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the defconfigs for r2d-plus and r2d-1 since we now have new drivers
for sm501 usb, spi-over-sci and epson r9701 rtc in mainline.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the unaligned access handling code to use opcode_t
instead of u16. While at it, enable unaligned access handling for sh2a.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds byte support to the sign extension code. Unaligned access
traps should never be generated on 8-bit io operations, but we will use this
code for trapped io and we do need byte support there.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
move update_process_times() out from under xtime_lock.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds basic support for the Migo-R board.
Only simple stuff provided by the cpu specific sh7722 code is in place now,
like serial console port, timers and usb gadget. There is also partial support
for the smc91c111 ethernet controller - unfortunately some driver header file
also needs patching (not included here) to make the driver get IRQ sense
information from the platform data.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Break out the sign extension code since it's used in multiple places.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for sh7722 devices with prr value 0xa1.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds the base address of SCIF0 in the case of sh7722.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
now that platform_device_register_simple() takes a "const chat *".
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the recently introduced declared coherent memory support.
Without this fix a cached memory area is returned by dma_alloc_coherent() -
unless dma_declare_coherent_memory() has setup a separate area.
This patch makes sure an uncached memory area is returned. With this patch
it is now possible to ping through an rtl8139 interface on r2d-plus.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a new sysfs entry under cpuidle states. desc - can be used by driver to
communicate to userspace any specific information about the state.
This helps in identifying the exact hardware C-states behind the ACPI C-state
definition.
Idea is to export this through powertop, which will help to map the C-state
reported by powertop to actual hardware C-state.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
For the 'return' command, GDB needs to adjust WINDOWBASE.
In case WB is different from 0, we need to rotate the
window register file and update WINDOWSTART and WMASK.
This patch also removes some ret|= statements for
__get_user/__put_user as the address range was alrady
checked a couple of lines earlier.
Signed-off-by: Chris Zankel <chris@zankel.net>
When building with binutils-2.18, vmlinux includes .note.gnu.build-id
sections that need to be stripped out when building the binary image.
The old .xt.insn sections haven't been used for a long time, so don't
bother stripping them.
Signed-off-by: Bob Wilson <bob.wilson@acm.org>
Signed-off-by: Chris Zankel <chris@zankel.net>
For processor configurations that have optional registers
(compiler-used but non-coprocessor), user space registers
might get corrupted when there are only 4 registers in
the current window-frame, ie. register a4 belongs to the
oldest frame in the register file.
Signed-off-by: Chris Zankel <chris@zankel.net>
Supporting the sa_restorer function allows for better security
since the sigreturn system call doesn't need to be placed on
the stack, so the stack doesn't need to be executable. This
requires support from the c-library as it has to provide the
restorer function.
Signed-off-by: Chris Zankel <chris@zankel.net>
The Xtensa architecture allows to define custom instructions and
registers. Registers that are bound to a coprocessor are only
accessible if the corresponding enable bit is set, which allows
to implement a 'lazy' context switch mechanism. Other registers
needs to be saved and restore at the time of the context switch
or during interrupt handling.
This patch adds support for these additional states:
- save and restore registers that are used by the compiler upon
interrupt entry and exit.
- context switch additional registers unbound to any coprocessor
- 'lazy' context switch of registers bound to a coprocessor
- ptrace interface to provide access to additional registers
- update configuration files in include/asm-xtensa/variant-fsf
Signed-off-by: Chris Zankel <chris@zankel.net>
We will never (need to) support signal handling coming from a
double exception. There are too many things that could go wrong
and delivering signals is not the fastest method for IPC, anyway.
Signed-off-by: Chris Zankel <chris@zankel.net>
We need to use vmalloc_exec for module loading. Also remove
the definitions MODULE_START and MODULE_END, which wasn't
used, and increase the VMALLOC memory range accordingly.
Signed-off-by: Chris Zankel <chris@zankel.net>
Register a2 is saved in depc but wasn't getting restored before
returning from _spill_registers when there weren't any registers
to spill. The mask to cut the top bit from the rotated WINDOWMASK
register was also one bit short.
Signed-off-by: CHris Zankel <chris@zankel.net>
Move boot-redboot load address from 0xD0200000 to 0xD1000000
to make space for larger kernel images, in particular those with
an embedded initramfs filesystem.
Also properly set the ELF start address in boot-elf images so
that PC need not be set manually when loading them using GDB.
Signed-off-by: Marc Gauthier <marc@tensilica.com>
Remove oldmask from the sigcontext structure. Also update wmask
and windowstart when we flush the AR registers to stack.
Signed-off-by: Chris Zankel <chris@zankel.net>
Remove additional registers from the ELF gregset structure that
are only used by the kernel or are not required or invalid in
user-space. The ar registers are always aligned to a windowbase
value of 0, and the WB register is always assumed to be 0.
Increase the size of the structure to 128 entries. This will
provide enough space in future.
Signed-off-by: Chris Zankel <chris@zankel.net>
The simcall asm macro assumes Windowed ABI parameter passing
in registers, and doesn't work if its containing function gets
inlined. This fix prevents that from happening.
Signed-off-by: Marc Gauthier <marc@tensilica.com>
The TLB entry for the user address doesn't exist at the time we
want to flush the caches, so use the page address. Note that processor
configurations with cache-aliasing issues are treated separately.
Signed-off-by: Chris Zankel <chris@zankel.net>
