Details:
1. Unload all modules on fw_list of dsp when suspend, and reload all
modules on fw_list when resume.
2. A DSP expects only one scratch, but hsw_parse_fw_image() allocates
scratch blocks for each firmware image it parses. Move the allocate function
sst_block_alloc_scratch() out of hsw_parse_fw_image() to make sure a scratch
be allocated only after all firmware images be parsed.
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The board ID will be changed between revisions. So, it is better
to map it by project name.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SGTL5000_CHIP_ANA_POWER register is cached. Update the cached
value instead of writing it directly.
Patch inspired by Russell King's more colorful remarks in this
patch:
https://github.com/SolidRun/linux-imx6-3.14/commit/dd4bf6a
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Commit fd316941c ("spi/pl022: disable port when unused") introduced a race,
which leads to possible driver lock up (easily reproducible on SMP).
The problem happens in giveback() function where the completion of the transfer
is signalled to SPI subsystem and then the HW SPI controller is disabled. Another
transfer might be setup in between, which brings driver in locked-up state.
Exact event sequence on SMP:
core0 core1
=> pump_transfers()
/* message->state == STATE_DONE */
=> giveback()
=> spi_finalize_current_message()
=> pl022_unprepare_transfer_hardware()
=> pl022_transfer_one_message
=> flush()
=> do_interrupt_dma_transfer()
=> set_up_next_transfer()
/* Enable SSP, turn on interrupts */
writew((readw(SSP_CR1(pl022->virtbase)) |
SSP_CR1_MASK_SSE), SSP_CR1(pl022->virtbase));
...
=> pl022_interrupt_handler()
=> readwriter()
/* disable the SPI/SSP operation */
=> writew((readw(SSP_CR1(pl022->virtbase)) &
(~SSP_CR1_MASK_SSE)), SSP_CR1(pl022->virtbase));
Lockup! SPI controller is disabled and the data will never be received. Whole
SPI subsystem is waiting for transfer ACK and blocked.
So, only signal transfer completion after disabling the controller.
Fixes: fd316941c (spi/pl022: disable port when unused)
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
In this pull request, there are a few more ASoC changes that have been
gathered since rc1, but it's still fairly calm over all. The only
largish LOC is found in atmel driver, and it's just a removal of
broken non-DT stuff. The rest are all small driver-specific fixes,
nothing to worry much.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJU+ayYAAoJEGwxgFQ9KSmkoN0QALYBlaGtCZVOHuNozArW41RB
9QdM0HQDXKFpMahsCWfY/0zOaEFZ4LROj/kkBeVwxgyMzEgom4gHT0U5UMdKI1Jt
351SAOAaB1s1UKWir2q56DxSaNdMyjHxFMMc1LlIXFJ2U3fsGbsgAGosGCAPpIdD
2SB+6wRwXPHl7HPGy7Pu/cqBitf4wMpkrWS4K2dXzEOxakEOmsPpS3oBVbxmo8BC
izn8L9iZ7FARQCRmLf0Sk3KECDwmgXcwnkBSfcRXjSYBj4eTMeMzc/FGiTSlIx2V
yMhq/et21ktYues4etaPXGvygjAIiODS4xjGrYYeQm6cvCTCUOOGWTUGfH4sA7i5
uJRWT3xyiAeDVF/s1FxkhqW3tYRYI1DpisNqPekoDkQkHp3GJBvzIBLqTUO0cnTO
TqhoqjXzji2gqf9IPV9d2fdtxuHlH/M+0dfivZ/4SXnZHWXU7pJE+OvslRGFCTP4
eIBz3J29Aqpa98VUnfLbAp0C+dBBuAI1J11bgi/b2shHjCMq+kDTrTfH3f04Jo94
xYcHyK9E5LqTpmzKak4hxc8ZajjU9YD/me1MyKcm+A1AAWONWcec6TVVDX9oxmUu
79nJQTFiXUauezJumDVyqv3QVCsDNDaxRJgIhyVx1MpRq68Iap+LQnYN9PDguY8/
a0/LsjVIzvOOr5Z1Z6BB
=f2XS
-----END PGP SIGNATURE-----
Merge tag 'sound-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a few more ASoC changes that have been gathered since rc1,
but it's still fairly calm over all. The only largish LOC is found in
atmel driver, and it's just a removal of broken non-DT stuff. The
rest are all small driver-specific fixes, nothing to worry much"
* tag 'sound-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (26 commits)
ALSA: hda - One more Dell macine needs DELL1_MIC_NO_PRESENCE quirk
ALSA: opl3: small array underflow
ALSA: line6: Clamp values correctly
ALSA: msnd: add some missing curly braces
ASoC: omap-pcm: Correct dma mask
ASoC: simple-card: Add a NULL pointer check in asoc_simple_card_dai_link_of
ASoC: sam9g20_wm8731: drop machine_is_xxx
ALSA: dice: fix wrong offsets for Dice interface
ALSA: oxfw: fix a condition and return code in start_stream()
ASoC: OMAP: mcbsp: Fix CLKX and CLKR pinmux when used as inputs
ASoC: rt5677: Correct the routing paths of that after IF1/2 DACx Mux
ASoC: sta32x: fix register range in regmap.
ASoC: rt5670: Set RT5670_IRQ_CTRL1 non volatile
ASoC: Intel: reset the DSP while suspending
ASoC: Intel: save and restore the CSR register
ASoC: Intel: update MMX ID to 3
ASoC: max98357a: Add missing header files
ASoC: cirrus: tlv320aic23 needs I2C
ASoC: Samsung: add missing I2C/SPI dependencies
ASoC: rt5670: Fix the speaker mono output issue
...
I upgraded my u-boot and noticed that wl12xx stopped working.
Turns out the kernel is not setting the quirk for the MMC2
copy clock while the eariler bootloader I had was setting it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Fix ACPI resources management problems introduced by the recent
rework of the code in question (Jiang Liu) and a build issue
introduced by those changes (Joachim Nilsson).
- Fix a recent suspend-to-idle regression on systems where entering
idle states causes local timers to stop, prevent suspend-to-idle
from crashing in restricted configurations (no cpuidle driver,
cpuidle disabled etc.) and clean up the idle loop somewhat while
at it (Rafael J Wysocki).
- Fix build problem in the cpufreq ppc driver (Geert Uytterhoeven).
- Allow the ACPI backlight driver module to be loaded if ACPI is
disabled which helps the i915 driver in those configurations
(stable-candidate) and change the code to help debug unusual use
cases (Chris Wilson).
- Wakeup IRQ management changes in v3.18 caused some drivers on the
at91 platform to trigger a warning from the IRQ core related to
an unexpected combination of interrupt action handler flags.
However, on at91 a timer IRQ is shared with some other devices
(including system wakeup ones) and that leads to the unusual
combination of flags in question. To make it possible to avoid
the warning introduce a new interrupt action handler flag (which
can be used by drivers to indicate the special case to the core)
and rework the problematic at91 drivers to use it and work as
expected during system suspend/resume. From Boris Brezillon,
Rafael J Wysocki and Mark Rutland.
- Clean up the generic power domains subsystem's debugfs interface
(Kevin Hilman).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=nc5T
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are fixes for recent regressions (ACPI resources management,
suspend-to-idle), stable-candidate fixes (ACPI backlight), fixes
related to the wakeup IRQ management changes made in v3.18, other
fixes (suspend-to-idle, cpufreq ppc driver) and a couple of cleanups
(suspend-to-idle, generic power domains, ACPI backlight).
Specifics:
- Fix ACPI resources management problems introduced by the recent
rework of the code in question (Jiang Liu) and a build issue
introduced by those changes (Joachim Nilsson).
- Fix a recent suspend-to-idle regression on systems where entering
idle states causes local timers to stop, prevent suspend-to-idle
from crashing in restricted configurations (no cpuidle driver,
cpuidle disabled etc.) and clean up the idle loop somewhat while at
it (Rafael J Wysocki).
- Fix build problem in the cpufreq ppc driver (Geert Uytterhoeven).
- Allow the ACPI backlight driver module to be loaded if ACPI is
disabled which helps the i915 driver in those configurations
(stable-candidate) and change the code to help debug unusual use
cases (Chris Wilson).
- Wakeup IRQ management changes in v3.18 caused some drivers on the
at91 platform to trigger a warning from the IRQ core related to an
unexpected combination of interrupt action handler flags. However,
on at91 a timer IRQ is shared with some other devices (including
system wakeup ones) and that leads to the unusual combination of
flags in question.
To make it possible to avoid the warning introduce a new interrupt
action handler flag (which can be used by drivers to indicate the
special case to the core) and rework the problematic at91 drivers
to use it and work as expected during system suspend/resume. From
Boris Brezillon, Rafael J Wysocki and Mark Rutland.
- Clean up the generic power domains subsystem's debugfs interface
(Kevin Hilman)"
* tag 'pm+acpi-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
genirq / PM: describe IRQF_COND_SUSPEND
tty: serial: atmel: rework interrupt and wakeup handling
watchdog: at91sam9: request the irq with IRQF_NO_SUSPEND
cpuidle / sleep: Use broadcast timer for states that stop local timer
clk: at91: implement suspend/resume for the PMC irqchip
rtc: at91rm9200: rework wakeup and interrupt handling
rtc: at91sam9: rework wakeup and interrupt handling
PM / wakeup: export pm_system_wakeup symbol
genirq / PM: Add flag for shared NO_SUSPEND interrupt lines
ACPI / video: Propagate the error code for acpi_video_register
ACPI / video: Load the module even if ACPI is disabled
PM / Domains: cleanup: rename gpd -> genpd in debugfs interface
cpufreq: ppc: Add missing #include <asm/smp.h>
x86/PCI/ACPI: Relax ACPI resource descriptor checks to work around BIOS bugs
x86/PCI/ACPI: Ignore resources consumed by host bridge itself
cpuidle: Clean up fallback handling in cpuidle_idle_call()
cpuidle / sleep: Do sanity checks in cpuidle_enter_freeze() too
idle / sleep: Avoid excessive disabling and enabling interrupts
PCI: versatile: Update for list_for_each_entry() API change
genirq / PM: better describe IRQF_NO_SUSPEND semantics
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ND3k
-----END PGP SIGNATURE-----
Merge tag 'locks-v4.0-3' of git://git.samba.org/jlayton/linux
Pull file locking fix from Jeff Layton:
"Just a single patch to fix a memory leak that Daniel Wagner discovered
while doing some testing with leases"
* tag 'locks-v4.0-3' of git://git.samba.org/jlayton/linux:
locks: fix fasync_struct memory leak in lease upgrade/downgrade handling
Highlights include:
- Fix a regression in the NFSv4 open state recovery code
- Fix a regression in the NFSv4 close code
- Fix regressions and side-effects of the loop-back mounted NFS fixes
in 3.18, that cause the NFS read() syscall to return EBUSY.
- Fix regressions around the readdirplus code and how it interacts with
the VFS lazy unmount changes that went into v3.18.
- Fix issues with out-of-order RPC call replies replacing updated
attributes with stale ones (particularly after a truncate()).
- Fix an underflow checking issue with RPC/RDMA credits
- Fix a number of issues with the NFSv4 delegation return/free code.
- Fix issues around stale NFSv4.1 leases when doing a mount
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qMB7
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-4.0-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
- Fix a regression in the NFSv4 open state recovery code
- Fix a regression in the NFSv4 close code
- Fix regressions and side-effects of the loop-back mounted NFS fixes
in 3.18, that cause the NFS read() syscall to return EBUSY.
- Fix regressions around the readdirplus code and how it interacts
with the VFS lazy unmount changes that went into v3.18.
- Fix issues with out-of-order RPC call replies replacing updated
attributes with stale ones (particularly after a truncate()).
- Fix an underflow checking issue with RPC/RDMA credits
- Fix a number of issues with the NFSv4 delegation return/free code.
- Fix issues around stale NFSv4.1 leases when doing a mount"
* tag 'nfs-for-4.0-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (24 commits)
NFSv4.1: Clear the old state by our client id before establishing a new lease
NFSv4: Fix a race in NFSv4.1 server trunking discovery
NFS: Don't write enable new pages while an invalidation is proceeding
NFS: Fix a regression in the read() syscall
NFSv4: Ensure we skip delegations that are already being returned
NFSv4: Pin the superblock while we're returning the delegation
NFSv4: Ensure we honour NFS_DELEGATION_RETURNING in nfs_inode_set_delegation()
NFSv4: Ensure that we don't reap a delegation that is being returned
NFS: Fix stateid used for NFS v4 closes
NFSv4: Don't call put_rpccred() under the rcu_read_lock()
NFS: Don't require a filehandle to refresh the inode in nfs_prime_dcache()
NFSv3: Use the readdir fileid as the mounted-on-fileid
NFS: Don't invalidate a submounted dentry in nfs_prime_dcache()
NFSv4: Set a barrier in the update_changeattr() helper
NFS: Fix nfs_post_op_update_inode() to set an attribute barrier
NFS: Remove size hack in nfs_inode_attrs_need_update()
NFSv4: Add attribute update barriers to delegreturn and pNFS layoutcommit
NFS: Add attribute update barriers to NFS writebacks
NFS: Set an attribute barrier on all updates
NFS: Add attribute update barriers to nfs_setattr_update_inode()
...
This series fixes the following bugs:
- a lockdep problem with the OMAP hwmod code;
- incorrect PCIe hwmod data for the DRA7xx chips;
- the clockdomain handling in the hardreset deassertion code,
preventing idle;
- the use of an IRQ status register rather than an IRQ enable register
in the OMAP4 PRM code.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.0-rc/20150301165949/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJU8+MlAAoJEMePsQ0LvSpLu5QP/19nHNQxGfKXdxrLmxk1Xn5Z
3iP9HO45JXEsADAA0Wk4awlX0qyVi0ho9QfKN2Z4xRD8TwTBUFmPHiGWJ9OJMVgm
4KFDiHXReexXiy/zGGbOx7rbiUztqnt5Ew9VXxbMEPxWCcA9ohT/Be+czKTAWqyX
f8sCE0G5amw7vbmbmMVixaV4fll4p42zsiLmZZJB/TJrBV9IBQySE61I9emDptuC
q4sjdysWI+3tCWqDk7yn+Ev7N5uw7sqReFnKLvbVLzfgu9BPQ5mDzVLC3CM5OQ0t
1ChZwe1RCjihDl9NHNZv7dchL5hf1AqYmoBdLTo8SpuOYdIa20UqEN77BR+JlWbh
BZImSXxFoICiWe0DLUjSmMDi//6f3rAcKxSyEFfjf76/73PkefRANdKImAQ5HRcp
9cd2qPC87NHm5iP1QO9cmidTRonfCzmVzD/gs7DZRjxB+QGLjB9mZY2hIZZBElII
SiONOiWvAci88llFQe6IQ7+a4OZMFb8vk837ceC00jJC7wxKEcHb1hOxlNqMOMWn
6rPsd01AlsyEenLGcU+fyM8r4my32Ewf9ECzTYAFi4tNP5gwqfrqIEhBHvqfO7/1
NgtYlHmVIhEsiB7M0ZtDh7FOzgyw+xp92b1kO6FIDXg5MuZqEgGvv5lAOKOrVwqt
FwANuzuSiro3muLphb7h
=HNIc
-----END PGP SIGNATURE-----
Merge tag 'for-v4.0-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.0/fixes
ARM: OMAP2+: first set of hwmod and PRCM fixes for v4.0-rc
This series fixes the following bugs:
- a lockdep problem with the OMAP hwmod code;
- incorrect PCIe hwmod data for the DRA7xx chips;
- the clockdomain handling in the hardreset deassertion code,
preventing idle;
- the use of an IRQ status register rather than an IRQ enable register
in the OMAP4 PRM code.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.0-rc/20150301165949/
Enable TWL4030_USB which is used at least on Nokia N900/N950/N9 (OMAP3)
and BeagleBoard.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The xhci in Intel Sunrisepoint and Cherryview platforms need a driver
workaround for a Stuck PME that might either block PME events in suspend,
or create spurious PME events preventing runtime suspend.
Workaround is to clear a internal PME flag, BIT(28) in a vendor specific
PMCTRL register at offset 0x80a4, in both suspend resume callbacks
Without this, xhci connected usb devices might never be able to wake up the
system from suspend, or prevent device from going to suspend (xhci d3)
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a control transfer has a short data stage, the xHCI controller generates
two transfer events: a COMP_SHORT_TX event that specifies the untransferred
amount, and a COMP_SUCCESS event. But when the data stage is not short, only the
COMP_SUCCESS event occurs. Therefore, xhci-hcd must set urb->actual_length to
urb->transfer_buffer_length while processing the COMP_SUCCESS event, unless
urb->actual_length was set already by a previous COMP_SHORT_TX event.
The driver checks this by seeing whether urb->actual_length == 0, but this alone
is the wrong test, as it is entirely possible for a short transfer to have an
urb->actual_length = 0.
This patch changes the xhci driver to rely on a new td->urb_length_set flag,
which is set to true when a COMP_SHORT_TX event is received and the URB length
updated at that stage.
This fixes a bug which affected the HSO plugin, which relies on URBs with
urb->actual_length == 0 to halt re-submitting the RX URB in the control
endpoint.
Cc: <stable@vger.kernel.org>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit bca9690b94 ("clk: divider: Make generic for usage elsewhere")
returned only the divider value for read-only dividers instead of the
actual rate.
Fixes: bca9690b94 ("clk: divider: Make generic for usage elsewhere")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Tested-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
DCAN1 RX and TX lines are internally pulled high according to [1].
While muxing between DCAN mode and SAFE mode we make sure
that the same pull direction is set to minimize opposite
pull contention during the switching window.
[1] in DRA7 data manual, Ball characteristics table 4-2, DSIS colum shows
the state driven to the peripheral input while in the deselcted mode.
DSIS - De-Selected Input State.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rev.F onwards ball G19 (dcan1_rx) is used as a GPIO for some other
function so don't include it in DCAN pinctrl node.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to AM437x TRM, Document SPRUHL7B, Revised December 2014,
Section 7.2.1 Pad Control Registers, setting bit 19 of the pad control
registers actually sets the SLEWCTRL value to slow rather than fast as
the current macro indicates. Introduce a new macro, SLEWCTRL_SLOW, that
sets the bit, and modify SLEWCTRL_FAST to 0 but keep it for
completeness.
Current users of the macro (i2c, mdio, and uart) are left unmodified as
SLEWCTRL_FAST was the macro used and actual desired state. Tested on
am437x-gp-evm with no difference in software performance seen.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to AM335x TRM, Document spruh73l, Revised February 2015,
Section 9.2.2 Pad Control Registers, setting bit 6 of the pad control
registers actually sets the SLEWCTRL value to slow rather than fast as
the current macro indicates. Introduce a new macro, SLEWCTRL_SLOW, that
sets the bit, and modify SLEWCTRL_FAST to 0 but keep it for
completeness.
Current users of the macro (i2c and mdio) are left unmodified as
SLEWCTRL_FAST was the macro used and actual desired state. Tested on
am335x-gp-evm with no difference in software performance seen.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 has a finer counter granularity, which allows for a delay of 1000ms
in the thermal zone polling intervals. OMAP5 has a different counter
mechanism, which allows at maximum a 500ms timer. Adjust the cpu thermal
zone polling interval accordingly.
Without this patch, the polling interval information is simply ignored,
and the following thermal warnings are printed during boot (assuming
thermal is enabled);
[ 1.545343] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[ 1.552691] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[ 1.560029] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use external clock for RMII since the internal clock doesn't meet the
jitter requirements.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Beaglebone Black doesn't have AES and SHAM enabled like the
original Beaglebone White dts. This breaks applications that
leverage the crypto blocks so fix this by enabling these nodes
in the am335x-bone-common.dtsi. With this change, enabling the
nodes in am335x-bone.dts is no longer required so remove them.
Signed-off-by: Matt Porter <mporter@konsulko.com>
Acked-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.
Fixes: 4da1c67719 ("add tbclk data for ehrpwm")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.
Fixes: 9e100ebafb: ("Fix ehrpwm tbclk data")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can simplify the code by returning patch_build_controls() directly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixes 85dc74e9 (ARM: dts: omap5 clock data)
On OMAP54xx, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.
This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck
Fix this by adding another mux clock as parent in bypass mode.
This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:
DPLL_IVA,
DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes: ee6c750761 (ARM: dts: dra7 clock data)
On DRA7x, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.
This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck
Fix this by adding another mux clock as parent in bypass mode.
This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:
DPLL_IVA, DPLL_DDR,
DPLL_DSP, DPLL_EVE,
DPLL_GMAC, DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Patch to add an VT1613 AC97 codec support.
This codec has additional DC offset removal control,
headphone output and no video input.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A selection of changes for v4.1 so far. The main things are:
- Move of jack registration to the card where it belongs.
- Support for DAPM routes specified by both the machine driver and DT.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU960DAAoJECTWi3JdVIfQkKIH/RDvxRn8dvKOPF5U9Uix3chH
JWKkzqfsMP0EpmQTzCQPp0ShAyYcWSbYsopicynPxUem5vS4Z8+UmOgEEgkj59pK
USbF6v1jCQXA6BcbKyUcRRBD9FtRkfVDc7mYbRs2CcwQz2CGCgee41cvPM+2BT+z
QdNC9UJARSweGvE1IUJSfpfYOly+BJ2s0/28RaQ0PGt+I0auoYx7IMFgMSDjv2p6
PY0kyQiwm3Kyj2uNXPZ5gEuPxlw/t8n4fbQNrBYAvxzN+EF5NrGdKE3N7MI1xRV/
EkFhzy+uM3X9c37tb2lT2fgPFlBc9rgPuLPSyoQ6nxa5ghCqAlgRhzpxRem8hhU=
=VlCw
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Changes for v4.1
A selection of changes for v4.1 so far. The main things are:
- Move of jack registration to the card where it belongs.
- Support for DAPM routes specified by both the machine driver and DT.
A few driver specific fixes here, none of them earth shattering in
themselves, that have accumliated since the opening of the merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU96stAAoJECTWi3JdVIfQLfUH/jBYQqxrPp8qm7Lt9LOuwC4U
SOi0ERIVhLSKZMo7G4wHmbEapx2FBgH+wxqh9kNLaISvOIH4odFS4Fr1XYE70cY9
97M46uzLqdaKCDgvkXdx1NLA0zubEGWLOtdVYlrMAzin0FXNH+KYhxkRQbJ6f0LE
yKmNemnHHtJ4gDl/kMED7bc+mkYSOpwUE/8HLOEA8bcE3luDnj7rvQwOhPIYq0Tz
Ij4GM8HSfWPp/k3YmZVcF8GA6icN3LG5Jg7DOu6S19fMYimTDaHQDCw0AoLfiIOQ
DykyHg7ay/I3B6zUz4JikLIW5KjFxZfeQ818YE0GQ4PgePfb0GSIFt0LnNmq4Oo=
=GIb7
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.0
A few driver specific fixes here, none of them earth shattering in
themselves, that have accumliated since the opening of the merge window.
Using the pvops kernel a NULL pointer dereference was detected on a
large machine (144 processors) when booting as dom0 in
evtchn_fifo_unmask() during assignment of a pirq.
The event channel in question was the first to need a new entry in
event_array[] in events_fifo.c. Unfortunately xen_irq_info_pirq_setup()
is called with evtchn being 0 for a new pirq and the real event channel
number is assigned to the pirq only during __startup_pirq().
It is mandatory to call xen_evtchn_port_setup() after assigning the
event channel number to the pirq to make sure all memory needed for the
event channel is allocated.
Signed-off-by: Juergen Gross <jgross@suse.com>
Cc: <stable@vger.kernel.org> # 3.14+
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
There is a missing lower bound check on "pitchbend" so it means we can
read up to 6 elements before the start of the opl3_note_table[] array.
Thanks to Clemens Ladisch for his help with this patch.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When CONFIG_DEBUG_SET_MODULE_RONX is enabled, the sizes of
module sections are aligned up so appropriate permissions can
be applied. Adjusting for the symbol table may cause them to
become unaligned. Make sure to re-align the sizes afterward.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The set_memory_* functions currently only support module
addresses. The addresses are validated using is_module_addr.
That function is special though and relies on internal state
in the module subsystem to work properly. At the time of
module initialization and calling set_memory_*, it's too early
for is_module_addr to work properly so it always returns
false. Rather than be subject to the whims of the module state,
just bounds check against the module virtual address range.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The BIOS might reconfigure pins as it needs when S3 is entered. This might
cause drivers using the GPIOs to fail because the state was wrong or
interrupts stopped working.
Fix this by saving and restoring enough pin context over system sleep.
Reported-by: Hans Holmberg <hans.holmberg@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When DMA descriptor allocation fails we should not try to assign any fields in
the bad descriptor. The patch adds the necessary checks for that.
Fixes: 7063c0d942 (spi/dw_spi: add DMA support)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Instead of handling everything in the driver's first level interrupt
handler, we can take advantage of already existing flow handlers that are
provided by the IRQ core.
This changes the functionality a bit also. Previously the driver looped
over pending interrupts in a single loop, restarting the loop if some
interrupt changed state. This caused problem with Lenovo Thinkpad 10
digitizer that it was not able to deassert the interrupt before the driver
disabled the interrupt for good (looplimit was exhausted).
Rework the interrupt handling logic a bit so that we provide proper mask,
ack and unmask operations in terms of Baytrail GPIO hardware and loop over
pending interrupts only once. If the interrupt remains asserted the first
level handler will be re-triggered automatically.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the pin is already configured as GPIO and it has any of the triggering
flags set, we may get spurious interrupts depending on the state of the
pin.
Prevent this by clearing the triggering flags on such pins. However, if the
pin is also configured as "direct IRQ" we leave the flags as is. Otherwise
it will prevent interrupts that are routed directly to IO-APIC.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Zotac ZBOX PI320, a Baytrail based mini-PC, has power button connected to a
GPIO pin and it is exposed to the operating system as Windows 8 button
array. This is implemented in Linux as a driver using gpio_keys.
However, BIOS on this particula machine forgot to mux the pin to be a GPIO
instead of native function, which results following message to be seen on
the console:
byt_gpio INT33FC:02: pin 16 cannot be used as GPIO.
This causes power button to not work as the driver was not able to request
the GPIO it needs.
So instead of completely preventing this we allow turning the pin as GPIO
but issue warning that something might be wrong.
Reported-by: Benjamin Adler <benadler@gmx.net>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On gcc5 the kernel does not link:
ld: .eh_frame_hdr table[4] FDE at 0000000000000648 overlaps table[5] FDE at 0000000000000670.
Because prior GCC versions always emitted NOPs on ALIGN directives, but
gcc5 started omitting them.
.LSTARTFDEDLSI1 says:
/* HACK: The dwarf2 unwind routines will subtract 1 from the
return address to get an address in the middle of the
presumed call instruction. Since we didn't get here via
a call, we need to include the nop before the real start
to make up for it. */
.long .LSTART_sigreturn-1-. /* PC-relative start address */
But commit 69d0627a7f ("x86 vDSO: reorder vdso32 code") from 2.6.25
replaced .org __kernel_vsyscall+32,0x90 by ALIGN right before
__kernel_sigreturn.
Of course, ALIGN need not generate any NOP in there. Esp. gcc5 collapses
vclock_gettime.o and int80.o together with no generated NOPs as "ALIGN".
So fix this by adding to that point at least a single NOP and make the
function ALIGN possibly with more NOPs then.
Kudos for reporting and diagnosing should go to Richard.
Reported-by: Richard Biener <rguenther@suse.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: <stable@vger.kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1425543211-12542-1-git-send-email-jslaby@suse.cz
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In xgene_pcie_map_bus(), we neglected to add in the register offset when
calculating the config space address. This means all config accesses
operated on the first four bytes of config space.
Add the register offset to the config space base address.
Also correct the xgene_pcie_map_bus() prototype to fix a compiler warning.
[bhelgaas: changelog]
Fixes: 350f8be5bb ("PCI: xgene: Convert to use generic config accessors")
Posting: http://lkml.kernel.org/r/1424214840-26498-1-git-send-email-fkan@apm.com
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tanmay Inamdar <tinamdar@apm.com>
Acked-by: Rob Herring <robh@kernel.org>
With some mss values, it is possible tcp_xmit_size_goal() puts
one segment more in TSO packet than tcp_tso_autosize().
We send then one TSO packet followed by one single MSS.
It is not a serious bug, but we can do slightly better, especially
for drivers using netif_set_gso_max_size() to lower gso_max_size.
Using same formula avoids these corner cases and makes
tcp_xmit_size_goal() a bit faster.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 605ad7f184 ("tcp: refine TSO autosizing")
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver is removed (e.g. using unbind through sysfs), the
clocks get disabled twice, once on fec_enet_close and once on
fec_drv_remove. Since the clocks are enabled only once, this leads
to a warning:
WARNING: CPU: 0 PID: 402 at drivers/clk/clk.c:992 clk_core_disable+0x64/0x68()
Remove the call to fec_enet_clk_enable in fec_drv_remove to balance
the clock enable/disable calls again. This has been introduce by
e8fcfcd568 ("net: fec: optimize the clock management to save power").
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The latest spec "I-IPA01-0266-USR Rev 10" limit the MID field length to 12 bit
value. For previous versions it is 16 bit value.
This change will not break the backward compatibility as the latest ID value is
7 and with in the 12 bit value limit.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eTSEC of-nodes may have children which are not queue-group nodes. For
example new-style fixed-phy declarations. These where incorrectly
assumed to be additional queue-groups.
Change the search to filter out any nodes which are not queue-groups,
or have been disabled.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree,
they are:
1) Don't truncate ethernet protocol type to u8 in nft_compat, from
Arturo Borrero.
2) Fix several problems in the addition/deletion of elements in nf_tables.
3) Fix module refcount leak in ip_vs_sync, from Julian Anastasov.
4) Fix a race condition in the abort path in the nf_tables transaction
infrastructure. Basically aborted rules can show up as active rules
until changes are unrolled, oneliner from Patrick McHardy.
5) Check for overflows in the data area of the rule, also from Patrick.
6) Fix off-by-one in the per-rule user data size field. This introduces
a new nft_userdata structure that is placed at the beginning of the
user data area that contains the length to save some bits from the
rule and we only need one bit to indicate its presence, from Patrick.
7) Fix rule replacement error path, the replaced rule is deleted on
error instead of leaving it in place. This has been fixed by relying
on the abort path to undo the incomplete replacement.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_check_defrag() may be used by af_packet to defragment outgoing packets.
skb_network_offset() of af_packet's outgoing packets is not zero.
Signed-off-by: Alexander Drozdov <al.drozdov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_set_wol() correctly sets MPD_PW_EN when a password is specified
to match magic packets against, however, when we switch from a
password-matching to a matching without password we would leave this bit
turned on, and GENET would only match magic packets with passwords.
This can be reproduced using the following sequence:
ethtool -s eth0 wol g
ethtool -s eth0 wol s sopass 00:11:22:33:44:55
ethtool -s eth0 wol g
The simple fix is to clear the MPD_PWD_EN bit when WAKE_MAGICSECURE is
not set.
Fixes: c51de7f397 ("net: bcmgenet: add Wake-on-LAN support code")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improper arithmetics when calculting the address of the extended ref could
lead to an out of bounds memory read and kernel panic.
Signed-off-by: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.cz>
cc: stable@vger.kernel.org # v3.7+
Signed-off-by: Chris Mason <clm@fb.com>
