The memory allocated for cs is not freed anywhere.
Convert to use devm_kzalloc to fix the memory leak.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently we save the host PMU configuration, counter values, etc.,
when entering a guest, and restore it on return from the guest.
(We have to do this because the guest has control of the PMU while
it is executing.) However, we missed saving/restoring the SIAR and
SDAR registers, as well as the registers which are new on POWER8,
namely SIER and MMCR2.
This adds code to save the values of these registers when entering
the guest and restore them on exit. This also works around the bug
in POWER8 where setting PMAE with a counter already negative doesn't
generate an interrupt.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Scott Wood <scottwood@freescale.com>
Commit c7699822bc21 ("KVM: PPC: Book3S HV: Make physical thread 0 do
the MMU switching") reordered the guest entry/exit code so that most
of the guest register save/restore code happened in guest MMU context.
A side effect of that is that the timebase still contains the guest
timebase value at the point where we compute and use vcpu->arch.dec_expires,
and therefore that is now a guest timebase value rather than a host
timebase value. That in turn means that the timeouts computed in
kvmppc_set_timer() are wrong if the timebase offset for the guest is
non-zero. The consequence of that is things such as "sleep 1" in a
guest after migration may sleep for much longer than they should.
This fixes the problem by converting between guest and host timebase
values as necessary, by adding or subtracting the timebase offset.
This also fixes an incorrect comment.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Scott Wood <scottwood@freescale.com>
With HV KVM, some high-frequency hypercalls such as H_ENTER are handled
in real mode, and need to access the memslots array for the guest.
Accessing the memslots array is safe, because we hold the SRCU read
lock for the whole time that a guest vcpu is running. However, the
checks that kvm_memslots() does when lockdep is enabled are potentially
unsafe in real mode, when only the linear mapping is available.
Furthermore, kvm_memslots() can be called from a secondary CPU thread,
which is an offline CPU from the point of view of the host kernel,
and is not running the task which holds the SRCU read lock.
To avoid false positives in the checks in kvm_memslots(), and to avoid
possible side effects from doing the checks in real mode, this replaces
kvm_memslots() with kvm_memslots_raw() in all the places that execute
in real mode. kvm_memslots_raw() is a new function that is like
kvm_memslots() but uses rcu_dereference_raw_notrace() instead of
kvm_dereference_check().
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Scott Wood <scottwood@freescale.com>
If an attempt is made to load the kvm-hv module on a machine which
doesn't have hypervisor mode available, return an ENODEV error,
which is the conventional thing to return to indicate that this
module is not applicable to the hardware of the current machine,
rather than EIO, which causes a warning to be printed.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Scott Wood <scottwood@freescale.com>
The in-kernel emulation of RTAS functions needs to read the argument
buffer from guest memory in order to find out what function is being
requested. The guest supplies the guest physical address of the buffer,
and on a real system the code that reads that buffer would run in guest
real mode. In guest real mode, the processor ignores the top 4 bits
of the address specified in load and store instructions. In order to
emulate that behaviour correctly, we need to mask off those bits
before calling kvm_read_guest() or kvm_write_guest(). This adds that
masking.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Scott Wood <scottwood@freescale.com>
This adds code to get/set_one_reg to read and write the new transactional
memory (TM) state.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Scott Wood <scottwood@freescale.com>
This adds saving of the transactional memory (TM) checkpointed state
on guest entry and exit. We only do this if we see that the guest has
an active transaction.
It also adds emulation of the TM state changes when delivering IRQs
into the guest. According to the architecture, if we are
transactional when an IRQ occurs, the TM state is changed to
suspended, otherwise it's left unchanged.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Scott Wood <scottwood@freescale.com>
The 3rd argument is pointer to the buffer, not a single __u8.
This has no bad sideeffect, as the stub is not using any of its
argument, but better have it correct.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
commit 3c86726cfe ("HID: make .raw_request mandatory") made .raw_request
mandatory and broke the Hyper-V mouse driver. This patch fixes the problem.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The buffer being sent to printk has already had format strings
resolved. The string should not be reinterpreted again to avoid any
unintended format strings from leaking into printk.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Pull networking fixes from David Miller:
1) We've discovered a common error in several networking drivers, they
put VLAN offload features into ->vlan_features, which would suggest
that they support offloading 2 or more levels of VLAN encapsulation.
Not only do these devices not do that, but we don't have the
infrastructure yet to handle that at all.
Fixes from Vlad Yasevich.
2) Fix tcpdump crash with bridging and vlans, also from Vlad.
3) Some MAINTAINERS updates for random32 and bonding.
4) Fix late reseeds of prandom generator, from Sasha Levin.
5) Bridge doesn't handle stacked vlans properly, fix from Toshiaki
Makita.
6) Fix deadlock in openvswitch, from Flavio Leitner.
7) get_timewait4_sock() doesn't report delay times correctly, fix from
Eric Dumazet.
8) Duplicate address detection and addrconf verification need to run in
contexts where RTNL can be obtained. Move them to run from a
workqueue. From Hannes Frederic Sowa.
9) Fix route refcount leaking in ip tunnels, from Pravin B Shelar.
10) Don't return -EINTR from non-blocking recvmsg() on AF_UNIX sockets,
from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (28 commits)
vlan: Warn the user if lowerdev has bad vlan features.
veth: Turn off vlan rx acceleration in vlan_features
ifb: Remove vlan acceleration from vlan_features
qlge: Do not propaged vlan tag offloads to vlans
bridge: Fix crash with vlan filtering and tcpdump
net: Account for all vlan headers in skb_mac_gso_segment
MAINTAINERS: bonding: change email address
MAINTAINERS: bonding: change email address
ipv6: move DAD and addrconf_verify processing to workqueue
tcp: fix get_timewait4_sock() delay computation on 64bit
openvswitch: fix a possible deadlock and lockdep warning
bridge: Fix handling stacked vlan tags
bridge: Fix inabillity to retrieve vlan tags when tx offload is disabled
vhost: validate vhost_get_vq_desc return value
vhost: fix total length when packets are too short
random32: avoid attempt to late reseed if in the middle of seeding
random32: assign to network folks in MAINTAINERS
net/mlx4_core: pass pci_device_id.driver_data to __mlx4_init_one during reset
core, nfqueue, openvswitch: Orphan frags in skb_zerocopy and handle errors
vlan: Set hard_header_len according to available acceleration
...
Vlad Yasevich says:
====================
Audit all drivers for correct vlan_features.
Some drivers set vlan acceleration features in vlan_features. This causes
issues with Q-in-Q/802.1ad configurations.
Audit all the drivers for correct vlan_features. Fix broken ones.
Add a warning to vlan code to help catch future offenders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers incorrectly assign vlan acceleration features to
vlan_features thus causing issues for Q-in-Q vlan configurations.
Warn the user of such cases.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For completeness, turn off vlan rx acceleration in vlan_features so
that it doesn't show up on q-in-q setups.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not include vlan acceleration features in vlan_features as that
precludes correct Q-in-Q operation.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qlge driver turns off NETIF_F_HW_CTAG_FILTER, but forgets to
turn off HW_CTAG_TX and HW_CTAG_RX on vlan devices. With the
current settings, q-in-q will only generate a single vlan header.
Remember to mask off CTAG_TX and CTAG_RX features in vlan_features.
CC: Shahed Shaikh <shahed.shaikh@qlogic.com>
CC: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
CC: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the vlan filtering is enabled on the bridge, but
the filter is not configured on the bridge device itself,
running tcpdump on the bridge device will result in a
an Oops with NULL pointer dereference. The reason
is that br_pass_frame_up() will bypass the vlan
check because promisc flag is set. It will then try
to get the table pointer and process the packet based
on the table. Since the table pointer is NULL, we oops.
Catch this special condition in br_handle_vlan().
Reported-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
CC: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_network_protocol() already accounts for multiple vlan
headers that may be present in the skb. However, skb_mac_gso_segment()
doesn't know anything about it and assumes that skb->mac_len
is set correctly to skip all mac headers. That may not
always be the case. If we are simply forwarding the packet (via
bridge or macvtap), all vlan headers may not be accounted for.
A simple solution is to allow skb_network_protocol to return
the vlan depth it has calculated. This way skb_mac_gso_segment
will correctly skip all mac headers.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge two fixes from Andrew Morton:
"The x86 fix should come from x86 guys but they appear to be
conferencing or otherwise distracted.
The ocfs2 fix is a bit of a mess - the code runs into an immediate
NULL deref and we're trying to work out how this got through test and
review, but we haven't heard from Goldwyn in the past few days.
Sasha's patch fixes the oops, but the feature as a whole is probably
broken. So this is a stopgap for 3.14 - I'll aim to get the real
fixes into 3.14.x"
* emailed patches from Andrew Morton akpm@linux-foundation.org>:
x86: fix boot on uniprocessor systems
ocfs2: check if cluster name exists before deref
On x86 uniprocessor systems topology_physical_package_id() returns -1
which causes rapl_cpu_prepare() to leave rapl_pmu variable uninitialized
which leads to GPF in rapl_pmu_init().
See arch/x86/kernel/cpu/perf_event_intel_rapl.c.
It turns out that physical_package_id and core_id can actually be
retreived for uniprocessor systems too. Enabling them also fixes
rapl_pmu code.
Signed-off-by: Artem Fetishev <artem_fetishev@epam.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit c74a3bdd9b ("ocfs2: add clustername to cluster connection") is
trying to strlcpy a string which was explicitly passed as NULL in the
very same patch, triggering a NULL ptr deref.
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: strlcpy (lib/string.c:388 lib/string.c:151)
CPU: 19 PID: 19426 Comm: trinity-c19 Tainted: G W 3.14.0-rc7-next-20140325-sasha-00014-g9476368-dirty #274
RIP: strlcpy (lib/string.c:388 lib/string.c:151)
Call Trace:
ocfs2_cluster_connect (fs/ocfs2/stackglue.c:350)
ocfs2_cluster_connect_agnostic (fs/ocfs2/stackglue.c:396)
user_dlm_register (fs/ocfs2/dlmfs/userdlm.c:679)
dlmfs_mkdir (fs/ocfs2/dlmfs/dlmfs.c:503)
vfs_mkdir (fs/namei.c:3467)
SyS_mkdirat (fs/namei.c:3488 fs/namei.c:3472)
tracesys (arch/x86/kernel/entry_64.S:749)
akpm: this patch probably disables the feature. A temporary thing to
avoid triviel oopses.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Goldwyn Rodrigues <rgoldwyn@suse.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
addrconf_join_solict and addrconf_join_anycast may cause actions which
need rtnl locked, especially on first address creation.
A new DAD state is introduced which defers processing of the initial
DAD processing into a workqueue.
To get rtnl lock we need to push the code paths which depend on those
calls up to workqueues, specifically addrconf_verify and the DAD
processing.
(v2)
addrconf_dad_failure needs to be queued up to the workqueue, too. This
patch introduces a new DAD state and stop the DAD processing in the
workqueue (this is because of the possible ipv6_del_addr processing
which removes the solicited multicast address from the device).
addrconf_verify_lock is removed, too. After the transition it is not
needed any more.
As we are not processing in bottom half anymore we need to be a bit more
careful about disabling bottom half out when we lock spin_locks which are also
used in bh.
Relevant backtrace:
[ 541.030090] RTNL: assertion failed at net/core/dev.c (4496)
[ 541.031143] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G O 3.10.33-1-amd64-vyatta #1
[ 541.031145] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[ 541.031146] ffffffff8148a9f0 000000000000002f ffffffff813c98c1 ffff88007c4451f8
[ 541.031148] 0000000000000000 0000000000000000 ffffffff813d3540 ffff88007fc03d18
[ 541.031150] 0000880000000006 ffff88007c445000 ffffffffa0194160 0000000000000000
[ 541.031152] Call Trace:
[ 541.031153] <IRQ> [<ffffffff8148a9f0>] ? dump_stack+0xd/0x17
[ 541.031180] [<ffffffff813c98c1>] ? __dev_set_promiscuity+0x101/0x180
[ 541.031183] [<ffffffff813d3540>] ? __hw_addr_create_ex+0x60/0xc0
[ 541.031185] [<ffffffff813cfe1a>] ? __dev_set_rx_mode+0xaa/0xc0
[ 541.031189] [<ffffffff813d3a81>] ? __dev_mc_add+0x61/0x90
[ 541.031198] [<ffffffffa01dcf9c>] ? igmp6_group_added+0xfc/0x1a0 [ipv6]
[ 541.031208] [<ffffffff8111237b>] ? kmem_cache_alloc+0xcb/0xd0
[ 541.031212] [<ffffffffa01ddcd7>] ? ipv6_dev_mc_inc+0x267/0x300 [ipv6]
[ 541.031216] [<ffffffffa01c2fae>] ? addrconf_join_solict+0x2e/0x40 [ipv6]
[ 541.031219] [<ffffffffa01ba2e9>] ? ipv6_dev_ac_inc+0x159/0x1f0 [ipv6]
[ 541.031223] [<ffffffffa01c0772>] ? addrconf_join_anycast+0x92/0xa0 [ipv6]
[ 541.031226] [<ffffffffa01c311e>] ? __ipv6_ifa_notify+0x11e/0x1e0 [ipv6]
[ 541.031229] [<ffffffffa01c3213>] ? ipv6_ifa_notify+0x33/0x50 [ipv6]
[ 541.031233] [<ffffffffa01c36c8>] ? addrconf_dad_completed+0x28/0x100 [ipv6]
[ 541.031241] [<ffffffff81075c1d>] ? task_cputime+0x2d/0x50
[ 541.031244] [<ffffffffa01c38d6>] ? addrconf_dad_timer+0x136/0x150 [ipv6]
[ 541.031247] [<ffffffffa01c37a0>] ? addrconf_dad_completed+0x100/0x100 [ipv6]
[ 541.031255] [<ffffffff8105313a>] ? call_timer_fn.isra.22+0x2a/0x90
[ 541.031258] [<ffffffffa01c37a0>] ? addrconf_dad_completed+0x100/0x100 [ipv6]
Hunks and backtrace stolen from a patch by Stephen Hemminger.
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dropping packets in __dev_queue_xmit() when transmit queue
is stopped (NIC TX ring buffer full or BQL limit reached) currently
outputs a syslog message.
It would be better to get a precise count of such events available in
netdevice stats so that monitoring tools can have a clue.
This extends the work done in caf586e5f2
("net: add a core netdev->rx_dropped counter")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quite often it can be useful to test with dummy or similar
devices as a blackhole sink for skbs. Such devices are only
equipped with a single txq, but marked as NETIF_F_LLTX as
they do not require locking their internal queues on xmit
(or implement locking themselves). Therefore, rather use
HARD_TX_{UN,}LOCK API, so that NETIF_F_LLTX will be respected.
trafgen mmap/TX_RING example against dummy device with config
foo: { fill(0xff, 64) } results in the following performance
improvements for such scenarios on an ordinary Core i7/2.80GHz:
Before:
Performance counter stats for 'trafgen -i foo -o du0 -n100000000' (10 runs):
160,975,944,159 instructions:k # 0.55 insns per cycle ( +- 0.09% )
293,319,390,278 cycles:k # 0.000 GHz ( +- 0.35% )
192,501,104 branch-misses:k ( +- 1.63% )
831 context-switches:k ( +- 9.18% )
7 cpu-migrations:k ( +- 7.40% )
69,382 cache-misses:k # 0.010 % of all cache refs ( +- 2.18% )
671,552,021 cache-references:k ( +- 1.29% )
22.856401569 seconds time elapsed ( +- 0.33% )
After:
Performance counter stats for 'trafgen -i foo -o du0 -n100000000' (10 runs):
133,788,739,692 instructions:k # 0.92 insns per cycle ( +- 0.06% )
145,853,213,256 cycles:k # 0.000 GHz ( +- 0.17% )
59,867,100 branch-misses:k ( +- 4.72% )
384 context-switches:k ( +- 3.76% )
6 cpu-migrations:k ( +- 6.28% )
70,304 cache-misses:k # 0.077 % of all cache refs ( +- 1.73% )
90,879,408 cache-references:k ( +- 1.35% )
11.719372413 seconds time elapsed ( +- 0.24% )
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As in xmit path we merely update statistics and free the skb, we
can mark the device with LLTX feature, so that upper layers can
avoid taking the single txq lock on xmit. While at it, also add
missing NETIF_F_SG.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems I missed one change in get_timewait4_sock() to compute
the remaining time before deletion of IPV4 timewait socket.
This could result in wrong output in /proc/net/tcp for tm->when field.
Fixes: 96f817fede ("tcp: shrink tcp6_timewait_sock by one cache line")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a bridge with vlan_filtering enabled receives frames with stacked
vlan tags, i.e., they have two vlan tags, br_vlan_untag() strips not
only the outer tag but also the inner tag.
br_vlan_untag() is called only from br_handle_vlan(), and in this case,
it is enough to set skb->vlan_tci to 0 here, because vlan_tci has already
been set before calling br_handle_vlan().
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge vlan code (br_vlan_get_tag()) assumes that all frames have vlan_tci
if they are tagged, but if vlan tx offload is manually disabled on bridge
device and frames are sent from vlan device on the bridge device, the tags
are embedded in skb->data and they break this assumption.
Extract embedded vlan tags and move them to vlan_tci at ingress.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz says:
====================
Implement vxlan ndo calls
This short series adds support for the vxlan ndo calls, the udp
port is programmed to the firmware using a new command we introduce
here which is called "config device".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add implementation for the add/del vxlan port ndo calls, using the
CONFIG_DEV firmware command.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the CONFIG_DEV firmware command which we will use to
configure the UDP port assumed by the firmware for the VXLAN offloads.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VF issues a firmware command which is disallowed for them, the PF
rerturns -EPERM from that command wrapper. Move to use one such wrapper
instance, instead of repeating the same code on such commands.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2dc33bbc4 "bnx2x: Remove the sriov VFOP mechanism" introduced a possible
memory leak on the error flow during multicast filters configuration.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vhost fails to validate negative error code
from vhost_get_vq_desc causing
a crash: we are using -EFAULT which is 0xfffffff2
as vector size, which exceeds the allocated size.
The code in question was introduced in commit
8dd014adfe
vhost-net: mergeable buffers support
CVE-2014-0055
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mergeable buffers are disabled, and the
incoming packet is too large for the rx buffer,
get_rx_bufs returns success.
This was intentional in order for make recvmsg
truncate the packet and then handle_rx would
detect err != sock_len and drop it.
Unfortunately we pass the original sock_len to
recvmsg - which means we use parts of iov not fully
validated.
Fix this up by detecting this overrun and doing packet drop
immediately.
CVE-2014-0077
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4af712e8df ("random32: add prandom_reseed_late() and call when
nonblocking pool becomes initialized") has added a late reseed stage
that happens as soon as the nonblocking pool is marked as initialized.
This fails in the case that the nonblocking pool gets initialized
during __prandom_reseed()'s call to get_random_bytes(). In that case
we'd double back into __prandom_reseed() in an attempt to do a late
reseed - deadlocking on 'lock' early on in the boot process.
Instead, just avoid even waiting to do a reseed if a reseed is already
occuring.
Fixes: 4af712e8df ("random32: add prandom_reseed_late() and call when nonblocking pool becomes initialized")
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull input subsystem fixes from Dmitry Torokhov:
"Updates to Synaptics touchpad to better cope with devices in Lenovo
laptops, and a couple more fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - add manual min/max quirk for ThinkPad X240
Input: synaptics - add manual min/max quirk
Input: cypress_ps2 - don't report as a button pads
Input: da9052_onkey - use correct register bit for key status
Input: adp5588-keys - get value from data out when dir is out
lib/random32.c was split out of the network code and is de-facto
still maintained by the almighty net/ gods.
Make it a bit more official so that people who aren't aware of
that know where to send their patches.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pm_rumtime work queue is causing the device to be suspended during
initialisation, thus the initialisation may not be able to access registers
properly. As the code is called from a work queue, it is possible that this
is not seen from certain configurations/builds due to the asynchronos
nature of the code.
Another issue has also been found where the network device registration
calls back into the driver thus causing further pm_runtime calls that
also caused issues with the MDIO bus code. This has now been checked
and is the only place the MDIO can be called without the device open.
Use pm_runtime_get_sync() and pm_runtime_put() to ensure that the
pm system does not suspend it during the probe() call and remove the
now unnecessary pm_runtime_resume() call. Also add a call in the error
path to call pm_runtime_disable().
This fixes the external abort that can cause /sbin/init or other such
init processed to die.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like the STi and sunxi series SOCs, Altera's SOCFPGA also needs a glue layer
on top of the Synopsys gmac IP.
This patch adds the platform driver for the glue layer which configures the IP
before the generic STMMAC driver takes over.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If kmalloc() fails in c4iw_alloc_ucontext(), the function
leaves but does not set an error code in ret variable:
it will return 0 to the caller.
This patch set ret to -ENOMEM in such case.
Cc: Steve Wise <swise@opengridcomputing.com>
Cc: Steve Wise <swise@chelsio.com>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Erik Hugne says:
====================
tipc: fix handling of NETDEV_CHANGEADDR event
Aside from manual reconfiguration of the netdevice hwaddr, this can also
be changed automatically for an interface bond in active-backup mode
if fail_over_mac is enabled. This patchset fixes the handling of this
event in TIPC by properly updating the l2 media address for the bearer,
followed by a reinitialization of the node discovery mechanism.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The node discovery domain is assigned when a bearer is enabled.
In the previous commit we reflect this attribute directly in the
bearer structure since it's needed to reinitialize the node
discovery mechanism after a hardware address change.
There's no need to replicate this attribute anywhere else, so we
remove it from the tipc_link_req structure.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
