Add support for adjusting volume when DSD (Direct Stream
Digital) audio playback is in progress.
Change-Id: Ica51d40911d16059e8af21c60794b35c68bb695d
Signed-off-by: Phani Kumar Uppalapati <phaniu@codeaurora.org>
Add DAPM (Dynamic Audio Power Management) widgets and
routing to enable support for DSD (Direct Stream Digital)
audio playback on wcd934x codec.
Change-Id: I06e1b0134cea58adedbd9113a51529b2b73da835
Signed-off-by: Phani Kumar Uppalapati <phaniu@codeaurora.org>
WCD934X supports mixing of integer sample rate clips with
fractional sample rate clips using ASRC(asynchronous sample
rate converter) block. Add support to use ASRC block in codec.
CRs-Fixed: 1054643
Change-Id: I3a04cc902c74b49e1d40c5a52acbf1f7c907c34e
Signed-off-by: Vidyakumar Athota <vathota@codeaurora.org>
Add support to enable codec MCLK2 which is used for
44.1KHz and its multiples sample rate audio playback.
CRs-Fixed: 1054643
Change-Id: Id157439b2a46ac4fa54b4a768f9555cf390399b5
Signed-off-by: Phani Kumar Uppalapati <phaniu@codeaurora.org>
WCD934X audio codec supports static voltage scaling (SVS) mode, which
puts the codec into lowest power state. The codec has different power
states (SVS2, SVS and Nominal). Add support in codec driver to vote
for SVS when audio usecases are enabled and remove vote for SVS when
audio usecases are disabled. The codec driver only votes for SVS or
no SVS and the hardware internally manages to go into Nominal mode.
CRs-Fixed: 1049012
Change-Id: I6f66d3136e3c49da54f5919184bc113267105463
Signed-off-by: Bhalchandra Gajare <gajare@codeaurora.org>
MAD (Microphone Activity Detection) hardware block in wcd934x audio
codec samples the microphone at configured intervals to sense
presence of valid audio signal. This is used for voice activation
use cases. Change adds widgets and routes to enable the MAD block.
CRs-Fixed: 1049012
Change-Id: I1ce4f3f215850fada6c25192a4351f3a9c76a370
Signed-off-by: Meng Wang <mwang@codeaurora.org>
Signed-off-by: Bhalchandra Gajare <gajare@codeaurora.org>
When a system is entering RPM assisted sleep, the NOACK messages are
not accounted in preventing such sleep modes as no driver is waiting
on it. In such scenarios, some active messages could still be in the
Apps RX buffer which reduces the number of outstanding sleep messages.
Fix by accounting for NOACK messages while flushing sleep set requests
and ensuring that they are read before sending any sleep set requests.
The original changes were reverted to address issues with SMD transport.
This change includes fixes from earlier squashed into a single commit.
Change-Id: I5570d7694424d0a602c446c0af098a64ffa681e4
Signed-off-by: Mahesh Sivasubramanian <msivasub@codeaurora.org>
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
On debug setups where the battery is not present, we need a way
to fake battery capacity instead of reporting some incorrect
/non-existent value. Provide means for the userspace to setup
a fake battery capacity.
Change-Id: Iff3ee1009d9c3215433cc267f016ef9cf2a9bff2
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Implement VOLTAGE_MAX_DESIGN to expose the battery float voltage. This
property will reflect the values read from battery profile and will
will be used for setting the max voltage on charging chips.
Change-Id: I4b9028f8930ac2f3de6c043fa145494f37322160
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Currently the name of the votable that suspends usb is INPUT_SUSPEND.
However, the PMI has two inputs - USB and DC. The dc suspending votable
is correctly named DC_SUSPEND. So rename the INPUT_SUSPEND to an
appropriate name - USB_SUSPEND.
Change-Id: Ia5ea1b139f5e9d560dc6492aa9fc13ffeeda83ca
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
with SMMU enable, the API page_to_phys() is
failed to get PA of the sg_page tbl. The WA
is to have wlan-driver directly send the PA
to ipa-driver.
Change-Id: I7750102222d519969da0d597a6591aa728abb27a
Signed-off-by: Skylar Chang <chiaweic@codeaurora.org>
Update power attributes for cpu and cluster's low power modes based on
the measurements on the device.
Breakeven points for v1 hardware:
Power Cluster -
Min us Max us Mode selected
83 1810 c1
1810 c3
Note: C2d is disabled in v1
L2 - Power Cluster
Min us Max us Mode selected
99 975 d1
976 3398 d2d
3399 9182 d2e
9183 d4
Perf Cluster
Min us Max us Mode selected
86 1704 c1
1704 c3
Note: C2d is disabled in v1
L2 - Perf Cluster
Min us Max us Mode selected
99 905 d1
906 3380 d2d
3381 9418 d2e
9419 d4
CCI
Min us Max us Mode selected
16744 e3
Change-Id: Iaf9930c0589e193c8a366ff44808d75c6d6b360b
Signed-off-by: Archana Sathyakumar <asathyak@codeaurora.org>
DEEP-NAP and SLEEP states are not used in targets of previous
two generations. They are neither saving GPU power, nor saving
system power. Remove to reduce maintenance overhead.
CRs-Fixed: 1053516
Change-Id: If2fc2701548f90bb7ea9559a87752e13a7b0f736
Signed-off-by: George Shen <sqiao@codeaurora.org>
For WLAN hardware to enter low power mode, LDO25 voltage needs to
be at 3.1V. Change the regulator node to add this change.
Also for icnss driver votes for LDO7, LDO17 and LDO25, use pin
control regulator votes.
CRs-fixed: 1059101
Change-Id: I894631f6085410bd9961a0e00ca5eb2cd7d0c5bd
Signed-off-by: Prashanth Bhatta <bhattap@codeaurora.org>
Hardware characterization has shown that ROs 10 and 12 should be
used along with RO 13 on MSMCOBALT v2 for the highest VDD_GFX CPR
corner (Turbo L1). Specify their target quotient values.
Change-Id: Id2084fd8913468372ad78ecf0d41427171f87bab
CRs-Fixed: 1054539
Signed-off-by: David Collins <collinsd@codeaurora.org>
Updating the GPU SMMU settings to match the settings
used during pre-sil testing.
Change-Id: I70e0b87c3575f5778726ae2855d68bf0e560206a
Signed-off-by: Jonathan Wicks <jwicks@codeaurora.org>
When the regulators are not managed by SDHCI host driver (i.e.,
when host->vmmc and host->vmmcq are absent), get the regulator
current capabilities through a new host op get_current_limit().
Change-Id: I097349ad4d2e8ffbafbeb5fe65910894fe909bd6
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Sayali Lokhande <sayalil@codeaurora.org>
This deliberately changes the behavior of the per-cpuset
cpus file to not be effected by hotplug. When a cpu is offlined,
it will be removed from the cpuset/cpus file. When a cpu is onlined,
if the cpuset originally requested that that cpu was part of the cpuset, that
cpu will be restored to the cpuset. The cpus files still
have to be hierachical, but the ranges no longer have to be out of
the currently online cpus, just the physically present cpus.
Change-Id: I3efbae24a1f6384be1e603fb56f0d3baef61d924
[ohaugan@codeaurora.org: Port to 4.4]
Git-commit: f180bcac788464a0baf3d79d76dd86d6972ea413
Git-repo: https://android.googlesource.com/kernel/common/msm.git
Signed-off-by: Olav Haugan <ohaugan@codeaurora.org>
The location of some fuel gauge SRAM registers have changed in
PMICOBALT v2. Add a new SRAM register map for v2 to handle these changes.
Change-Id: I1fcfce8e56b1d4e8b8f54457193cd547fb5e3de7
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
IPA-driver should request for
aggre2_noc_clk via bus driver.
Change-Id: I2f44b44a27ae93c6dd46cc6829d68ea1117ba237
Signed-off-by: Skylar Chang <chiaweic@codeaurora.org>
Wlan need to pass the VA to let the IPA-driver
decide when to suspend the WDI pipe in SMMU
enabled scenario.
Change-Id: I00ae7f088c7411c8a6420f5e7ab12276d65fd269
Signed-off-by: Skylar Chang <chiaweic@codeaurora.org>
This change is to fix issues reported when OUTPUT and OUTPUT2
ports enabled in Venus. In this case following are the rules
- s_fmt on OUTPUT port updates OUTPUT port dimensions.
- s_fmt on CAPTURE port updates CAPTURE port dimensions.
- reconfig dimensions are always updated on OUTPUT port.
- All clocks scaling, bus scaling uses max of both ports.
- DCVS is based on reconfig, CAPTURE and OUTPUT port dims.
CRs-Fixed: 1044772
Change-Id: Ib45424c70f995d856ad27107ae3ea24a59ca4e74
Signed-off-by: Praneeth Paladugu <ppaladug@codeaurora.org>
Signed-off-by: Abdulla Anam <abdullahanam@codeaurora.org>
Set the status property of the qcom,memlat-mon-cpu4 device. This is
required for partial binned devices.
Change-Id: I246a5f5149e492aba4f7c3920296d4bd3d873de0
Signed-off-by: David Keitel <dkeitel@codeaurora.org>
Using first fit algorithm to select the remote rx intent from the
list is not optimal way.
Optimize the selection of intent from list using the best fit algorithm.
CRs-Fixed: 1058750
Change-Id: I7b2a70188975b75a0fbcd2a6cb26f28cc0258532
Signed-off-by: Dhoat Harpal <hdhoat@codeaurora.org>
