This is a bad one. I wonder whether we were so far protected by
no_free_segments(sb) usually being smaller than LOGFS_NO_AREAS.
Found by Dan Carpenter <dan.carpenter@oracle.com> using smatch.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Prasad Joshi <prasadjoshi.linux@gmail.com>
LogFS sets PG_private flag to indicate a pined page. We assumed that
marking a page as private is enough to ensure its existence. But
instead it is necessary to hold a reference count to the page.
The change resolves the following BUG
BUG: Bad page state in process flush-253:16 pfn:6a6d0
page flags: 0x100000000000808(uptodate|private)
Suggested-and-Acked-by: Joern Engel <joern@logfs.org>
Signed-off-by: Prasad Joshi <prasadjoshi.linux@gmail.com>
caif is a subsystem and as such it needs to register with
register_pernet_subsys instead of register_pernet_device.
Among other problems using register_pernet_device was resulting in
net_generic being called before the caif_net structure was allocated.
Which has been causing net_generic to fail with either BUG_ON's or by
return NULL pointers.
A more ugly problem that could be caused is packets in flight why the
subsystem is shutting down.
To remove confusion also remove the cruft cause by inappropriately
trying to fix this bug.
With the aid of the previous patch I have tested this patch and
confirmed that using register_pernet_subsys makes the failure go away as
it should.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Tested-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By definition net_generic should never be called when it can return
NULL. Fail conspicously with a BUG_ON to make it clear when people mess
up that a NULL return should never happen.
Recently there was a bug in the CAIF subsystem where it was registered
with register_pernet_device instead of register_pernet_subsys. It was
erroneously concluded that net_generic could validly return NULL and
that net_assign_generic was buggy (when it was just inefficient).
Hopefully this BUG_ON will prevent people to coming to similar erroneous
conclusions in the futrue.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Tested-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's only used to get at neigh->primary_key, which in this context is
always going to be the same as rt->rt6i_gateway.
Signed-off-by: David S. Miller <davem@davemloft.net>
In this specific situation we know we are dealing with a gatewayed route
and therefore rt6i_gateway is not going to be in6addr_any even in future
interpretations.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now all code paths grab a local reference to the neigh, so if neigh
is not NULL we unconditionally release it at the end. The old logic
would only release if we didn't have a non-NULL 'rt'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use virtio_mb() to make sure the available index to be exposed before
checking the the avail event. Otherwise we may get stale value of
avail event in guest and never kick the host after.
Note: this fixes a bug introduced by ee7cd8981e.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Note: this fixes a bug introduced recently in
7b21e34fd1.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Since commit 576d2f2525 "ARM: add
generic ioremap optimization by reusing static mappings" ioremap()
is trying to reuse existing static mapping when possible.
The condition checking boundaries of the requested and existing
mappings didn't take in-page offset into consideration though,
which lead to obscure and hard to debug problems when requested
mapping crossed end of the static one.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The irq handler was a mess.
See 7ab87ff4c7 ("via-rhine: move work from
irq handler to softirq and beyond") for similar changes. One can notice:
- all non-napi tasks are explicitely scheduled trough a single work queue.
- hiding software tx queue start behind the rtl_hw_start method is mildly
natural. Move it in the caller where needed.
- as can be seen from the heavy use of bh disabling locks, the driver is
not safe for irq context messages with netconsole. It is still quite
usable for general messaging though. Tested ok with concurrent registers
dump (ethtool -d) + background traffic + "echo t > /proc/sysrq-trigger".
Tested with old PCI chipset, PCIe 8168 and 810x:
- XID 0c900800 RTL8168evl/8111evl
- XID 18000000 RTL8168b/8111b
- XID 98000000 RTL8169sc/8110sc
- XID 083000c0 RTL8168d/8111d
- XID 081000c0 RTL8168d/8111d
- XID 00b00000 RTL8105e
- XID 04a00000 RTL8102e
As a side note, the comments in f11a377b3f
("r8169: avoid losing MSI interrupts") does not seem completely clear: if
I hack the driver further to stop acking the irq link event bit, MSI
interrupts keep being delivered (RTL8168b/8111b, XID 18000000).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
* commit 'v3.3-rc1': (9775 commits)
Linux 3.3-rc1
x86, syscall: Need __ARCH_WANT_SYS_IPC for 32 bits
qnx4: don't leak ->BitMap on late failure exits
qnx4: reduce the insane nesting in qnx4_checkroot()
qnx4: di_fname is an array, for crying out loud...
KEYS: Permit key_serial() to be called with a const key pointer
keys: fix user_defined key sparse messages
ima: fix cred sparse warning
uml: fix compile for x86-64
MPILIB: Add a missing ENOMEM check
tpm: fix (ACPI S3) suspend regression
nvme: fix merge error due to change of 'make_request_fn' fn type
xen: using EXPORT_SYMBOL requires including export.h
gpio: tps65910: Use correct offset for gpio initialization
acpi/apei/einj: Add extensions to EINJ from rev 5.0 of acpi spec
intel_idle: Split up and provide per CPU initialization func
ACPI processor: Remove unneeded variable passed by acpi_processor_hotadd_init V2
tg3: Fix single-vector MSI-X code
openvswitch: Fix multipart datapath dumps.
ipv6: fix per device IP snmp counters
...
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (31 commits)
gma500: Fix suspend/resume functions
drm/exynos: fixed pm feature for fimd module.
MAINTAINERS: added maintainer entry for Exynos DRM Driver.
drm/exynos: fixed build dependency for DRM_EXYNOS_FIMD
drm/exynos: fix build dependency for DRM_EXYNOS_HDMI
drm/exynos: use release_mem_region instead of release_resource
agp: fix scratch page cleanup
drm/i915: fixup forcewake spinlock fallout in drpc debugfs function
drm/i915: debugfs: show semaphore registers also on gen7
drm/i915: allow userspace forcewake references also on gen7
drm/i915: Re-enable gen7 RC6 and GPU turbo after resume.
drm/i915: Correct debugfs printout for RC1e.
Revert "drm/i915: Work around gen7 BLT ring synchronization issues."
drm/i915: rip out the HWSTAM missed irq workaround
drm/i915: paper over missed irq issues with force wake voodoo
drm/i915: Hold gt_lock across forcewake register reads
drm/i915: Hold gt_lock during reset
drm/i915: Move reset forcewake processing to gen6_do_reset
drm/i915: protect force_wake_(get|put) with the gt_lock
drm/i915: convert force_wake_get to func pointer in the gpu reset code
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix silent output on Haier W18 laptop
ALSA: hda: set mute led polarity for laptops with buggy BIOS based on SSID
ALSA: hda - Fix silent output on ASUS A6Rp
ALSA: Fix memory leak on error in snd_compr_set_params()
ALSA: ymfpci - Don't create invalid PCM & mixers when AC97 doesn't support
Josef fixed btrfs_page_mkwrite to properly release reserved
extents if there was an error. But if we fail to get a reservation
and we fail to dirty the inode (for ENOSPC reasons), we'll end up
trying to release a reservation we never had.
This makes sure we only release if we were able to reserve.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Both the suspend and resume functions incorrectly set psbfb =
to_psb_fb(NULL) outside of the loop over all of the framebuffers. Fix
this by moving the assignment of psbfb inside the loop and removing the
initialisation of fb.
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch adds the TCO Watchdog DeviceIDs for the Intel Lynx Point PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Let the watchdog core to check the valid value range of min_timeout/max_timeout.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Correct typo "unexpectdly" to "unexpectedly" in pnx4008_wdt.c
and stmp3xxx_wdt.c
Signed-off-by: Masanari Iida<standby24x7@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Though motivated by the move of the driver to a single work queue of
sequential events and removal of hard irq processing, it looks safe as
a standalone change.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
I see no good reason to keep both rtl8169_reinit_task and rtl8169_reset_task:
- rtl8169_reinit_task adds a software failure point which does relate to
any hardware state
- they handle hardware the same. Remember that rtl8169_reinit_task was
introduced in the 8169 only era to handle PCI errors way before the 8168
asked for pll and firmware ops and compare :
rtl8169_reinit_task | rtl8169_reset_task
----------------------------+--------------------------
rtl8169_wait_for_quiescence | rtl8169_hw_reset
rtl8169_update_counters | rtl8169_wait_for_quiescence
rtl8169_hw_reset | rtl_hw_start
rtl8169_rx_missed | rtl8169_check_link_status
rtl_pll_power_down |
rtl_request_firmware |
rtl8169_init_phy |
rtl_pll_power_up |
rtl_hw_start |
rtl8169_check_link_status |
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
While receiving WDIOS_DISABLECARD option for WDIOC_SETOPTIONS command,
call wafwdt_stop() to disable watchdog.
Call wafwdt_start() while receiving WDIOS_ENABLECARD option.
Current code has reverse behavior.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
While receiving WDIOS_DISABLECARD option for WDIOC_SETOPTIONS command,
call wm8350_wdt_stop() to disable watchdog.
Call wm8350_wdt_start() while receiving WDIOS_ENABLECARD option.
Current code has reverse behavior.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
It is only used in this driver, so no need to make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
It is only used in this driver, so no need to make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Marc Vertes <marc.vertes@sigfox.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Currently the watchdog driver calls the pm_runtime_enable and never
the disable. This may cause a warning when pm_runtime_enable
checks for the count match.
Also fixes the error
/build/watchdog # insmod omap_wdt.ko
[ 44.999389] omap_wdt omap_wdt: Unbalanced pm_runtime_enable!
[ 45.011047] OMAP Watchdog Timer Rev 0x00: initial timeout 60 sec
/build/watchdog #
Attempting to fix the same by calling pm_runtime_disable.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Reimplement a call to devm_request_mem_region followed by a call to ioremap
or ioremap_nocache by a call to devm_request_and_ioremap.
The semantic patch that makes this transformation is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@nm@
expression myname;
identifier i;
@@
struct platform_driver i = { .driver = { .name = myname } };
@@
expression dev,res,size;
expression nm.myname;
@@
-if (!devm_request_mem_region(dev, res->start, size,
- \(res->name\|dev_name(dev)\|myname\))) {
- ...
- return ...;
-}
... when != res->start
(
-devm_ioremap(dev,res->start,size)
+devm_request_and_ioremap(dev,res)
|
-devm_ioremap_nocache(dev,res->start,size)
+devm_request_and_ioremap(dev,res)
)
... when any
when != res->start
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Reimplement a call to devm_request_mem_region followed by a call to ioremap
or ioremap_nocache by a call to devm_request_and_ioremap.
The variable res_size is then no longer needed.
The semantic patch that makes this transformation is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@nm@
expression myname;
identifier i;
@@
struct platform_driver i = { .driver = { .name = myname } };
@@
expression dev,res,size;
expression nm.myname;
@@
-if (!devm_request_mem_region(dev, res->start, size,
- \(res->name\|dev_name(dev)\|myname\))) {
- ...
- return ...;
-}
... when != res->start
(
-devm_ioremap(dev,res->start,size)
+devm_request_and_ioremap(dev,res)
|
-devm_ioremap_nocache(dev,res->start,size)
+devm_request_and_ioremap(dev,res)
)
... when any
when != res->start
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* 'fixes-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
mach-ux500: no MMC_CAP_SD_HIGHSPEED on Snowball
mach-ux500: enable ARM errata 764369
mach-ux500: do not override outer.inv_all
mach-ux500: musb: now musb is always in OTG mode
this patch separates fimd specific power on/off function from pm function
and the pm interfaces will call that function for power on or off.
and also removes unnecessary codes of resume function.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The generic lib.c file contains code relative to the various MACs, NVM and
Manageability supported by the driver. This patch splits the file into
three which are specific to those areas similar to how the PHY-specific
code is in phy.c and code specific to the 80003es2lan, 8257x, and ichX
MAC families are in their own files. The generic code that is applicable
to all MAC/PHY parts supported by the driver remains in netdev.c, param.c
and ethtool.c files. No change in functionality, just moving code
around for ease of maintenance, with some whitespace and other checkpatch
cleanups.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
__er16flash() is not meant to be called directly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Convert the last instances of strncpy() to the preferred strlcpy().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
