commit 871e178e0f2c4fa788f694721a10b4758d494ce1 upstream.
In the "ibm,configure-pe" and "ibm,configure-bridge" RTAS calls, the
spec states that values of 9900-9905 can be returned, indicating that
software should delay for 10^x (where x is the last digit, i.e. 990x)
milliseconds and attempt the call again. Currently, the kernel doesn't
know about this, and respecting it fixes some PCI failures when the
hypervisor is busy.
The delay is capped at 0.2 seconds.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a0cdbfd17b90a89c64a71d8aec9773ecdb20d0d upstream.
The function eeh_pe_reset_and_recover() is used to recover EEH
error when the passthrou device are transferred to guest and
backwards. The content in the device's config space will be lost
on PE reset issued in the middle of the recovery. The function
saves/restores it before/after the reset. However, config access
to some adapters like Broadcom BCM5719 at this point will causes
fenced PHB. The config space is always blocked and we save 0xFF's
that are restored at late point. The memory BARs are totally
corrupted, causing another EEH error upon access to one of the
memory BARs.
This restores the config space on those adapters like BCM5719
from the content saved to the EEH device when it's populated,
to resolve above issue.
Fixes: 5cfb20b9 ("powerpc/eeh: Emulate EEH recovery for VFIO devices")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2078d9ef600bdbe568c89e5ddc2c6f15b7982c8 upstream.
This reverts commit 89a51df5ab.
The function eeh_add_device_early() is used to perform EEH
initialization in devices added later on the system, like in
hotplug/DLPAR scenarios. Since the commit 89a51df5ab ("powerpc/eeh:
Fix crash in eeh_add_device_early() on Cell") a new check was introduced
in this function - Cell has no EEH capabilities which led to kernel oops
if hotplug was performed, so checking for eeh_enabled() was introduced
to avoid the issue.
However, in architectures that EEH is present like pSeries or PowerNV,
we might reach a case in which no PCI devices are present on boot time
and so EEH is not initialized. Then, if a device is added via DLPAR for
example, eeh_add_device_early() fails because eeh_enabled() is false,
and EEH end up not being enabled at all.
This reverts the aforementioned patch since a new verification was
introduced by the commit d91dafc02f ("powerpc/eeh: Delay probing EEH
device during hotplug") and so the original Cell issue does not happen
anymore.
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit affeb0f2d3a9af419ad7ef4ac782e1540b2f7b28 upstream.
The function eeh_pe_reset_and_recover() is used to recover EEH
error when the passthrough device are transferred to guest and
backwards, meaning the device's driver is vfio-pci or none.
When the driver is vfio-pci that provides error_detected() error
handler only, the handler simply stops the guest and it's not
expected behaviour. On the other hand, no error handlers will
be called if we don't have a bound driver.
This ignores the error handler in eeh_pe_reset_and_recover()
that reports the error to device driver to avoid the exceptional
behaviour.
Fixes: 5cfb20b9 ("powerpc/eeh: Emulate EEH recovery for VFIO devices")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ed8ab40047a570fdd8043a40c104a57248dd3fd upstream.
Some of the interrupt vectors on 64-bit POWER server processors are only
32 bytes long (8 instructions), which is not enough for the full
first-level interrupt handler. For these we need to branch to an
out-of-line (OOL) handler. But when we are running a relocatable kernel,
interrupt vectors till __end_interrupts marker are copied down to real
address 0x100. So, branching to labels (ie. OOL handlers) outside this
section must be handled differently (see LOAD_HANDLER()), considering
relocatable kernel, which would need at least 4 instructions.
However, branching from interrupt vector means that we corrupt the
CFAR (come-from address register) on POWER7 and later processors as
mentioned in commit 1707dd16. So, EXCEPTION_PROLOG_0 (6 instructions)
that contains the part up to the point where the CFAR is saved in the
PACA should be part of the short interrupt vectors before we branch out
to OOL handlers.
But as mentioned already, there are interrupt vectors on 64-bit POWER
server processors that are only 32 bytes long (like vectors 0x4f00,
0x4f20, etc.), which cannot accomodate the above two cases at the same
time owing to space constraint. Currently, in these interrupt vectors,
we simply branch out to OOL handlers, without using LOAD_HANDLER(),
which leaves us vulnerable when running a relocatable kernel (eg. kdump
case). While this has been the case for sometime now and kdump is used
widely, we were fortunate not to see any problems so far, for three
reasons:
1. In almost all cases, production kernel (relocatable) is used for
kdump as well, which would mean that crashed kernel's OOL handler
would be at the same place where we end up branching to, from short
interrupt vector of kdump kernel.
2. Also, OOL handler was unlikely the reason for crash in almost all
the kdump scenarios, which meant we had a sane OOL handler from
crashed kernel that we branched to.
3. On most 64-bit POWER server processors, page size is large enough
that marking interrupt vector code as executable (see commit
429d2e83) leads to marking OOL handler code from crashed kernel,
that sits right below interrupt vector code from kdump kernel, as
executable as well.
Let us fix this by moving the __end_interrupts marker down past OOL
handlers to make sure that we also copy OOL handlers to real address
0x100 when running a relocatable kernel.
This fix has been tested successfully in kdump scenario, on an LPAR with
4K page size by using different default/production kernel and kdump
kernel.
Also tested by manually corrupting the OOL handlers in the first kernel
and then kdump'ing, and then causing the OOL handlers to fire - mpe.
Fixes: c1fb6816fb ("powerpc: Add relocation on exception vector handlers")
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4c112114aab9aff5ed4568ca5e662bb02cdfe74 upstream.
In create_zero_mask() we have:
addi %1,%2,-1
andc %1,%1,%2
popcntd %0,%1
using the "r" constraint for %2. r0 is a valid register in the "r" set,
but addi X,r0,X turns it into an li:
li r7,-1
andc r7,r7,r0
popcntd r4,r7
Fix this by using the "b" constraint, for which r0 is not a valid
register.
This was found with a kernel build using gcc trunk, narrowed down to
when -frename-registers was enabled at -O2. It is just luck however
that we aren't seeing this on older toolchains.
Thanks to Segher for working with me to find this issue.
Fixes: d0cebfa650 ("powerpc: word-at-a-time optimization for 64-bit Little Endian")
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e924c60db1 which was
commit 7f821fc9c7 upstream.
It shouldn't have been applied as the original was already in 4.4.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4705e02498d6d5a7ab98dfee9595cd5e91db2017 upstream.
We need to update the user TM feature bits (PPC_FEATURE2_HTM and
PPC_FEATURE2_HTM) to mirror what we do with the kernel TM feature
bit.
At the moment, if firmware reports TM is not available we turn off
the kernel TM feature bit but leave the userspace ones on. Userspace
thinks it can execute TM instructions and it dies trying.
This (together with a QEMU patch) fixes PR KVM, which doesn't currently
support TM.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit beff82374b259d726e2625ec6c518a5f2613f0ae upstream.
scan_features() updates cpu_user_features but not cpu_user_features2.
Amongst other things, cpu_user_features2 contains the user TM feature
bits which we must keep in sync with the kernel TM feature bit.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6997e57d693b07289694239e52a10d2f02c3a46f upstream.
The REAL_LE feature entry in the ibm_pa_feature struct is missing an MMU
feature value, meaning all the remaining elements initialise the wrong
values.
This means instead of checking for byte 5, bit 0, we check for byte 0,
bit 0, and then we incorrectly set the CPU feature bit as well as MMU
feature bit 1 and CPU user feature bits 0 and 2 (5).
Checking byte 0 bit 0 (IBM numbering), means we're looking at the
"Memory Management Unit (MMU)" feature - ie. does the CPU have an MMU.
In practice that bit is set on all platforms which have the property.
This means we set CPU_FTR_REAL_LE always. In practice that seems not to
matter because all the modern cpus which have this property also
implement REAL_LE, and we've never needed to disable it.
We're also incorrectly setting MMU feature bit 1, which is:
#define MMU_FTR_TYPE_8xx 0x00000002
Luckily the only place that looks for MMU_FTR_TYPE_8xx is in Book3E
code, which can't run on the same cpus as scan_features(). So this also
doesn't matter in practice.
Finally in the CPU user feature mask, we're setting bits 0 and 2. Bit 2
is not currently used, and bit 0 is:
#define PPC_FEATURE_PPC_LE 0x00000001
Which says the CPU supports the old style "PPC Little Endian" mode.
Again this should be harmless in practice as no 64-bit CPUs implement
that mode.
Fix the code by adding the missing initialisation of the MMU feature.
Also add a comment marking CPU user feature bit 2 (0x4) as reserved. It
would be unsafe to start using it as old kernels incorrectly set it.
Fixes: 44ae3ab335 ("powerpc: Free up some CPU feature bits by moving out MMU-related features")
Signed-off-by: Anton Blanchard <anton@samba.org>
[mpe: Flesh out changelog, add comment reserving 0x4]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08a5bb2921e490939f78f38fd0d02858bb709942 upstream.
hugepd_free() used __get_cpu_var() once. Nothing ensured that the code
accessing the variable did not migrate from one CPU to another and soon
this was noticed by Tiejun Chen in 94b09d7554 ("powerpc/hugetlb:
Replace __get_cpu_var with get_cpu_var"). So we had it fixed.
Christoph Lameter was doing his __get_cpu_var() replaces and forgot
PowerPC. Then he noticed this and sent his fixed up batch again which
got applied as 69111bac42 ("powerpc: Replace __get_cpu_var uses").
The careful reader will noticed one little detail: get_cpu_var() got
replaced with this_cpu_ptr(). So now we have a put_cpu_var() which does
a preempt_enable() and nothing that does preempt_disable() so we
underflow the preempt counter.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c88c5d43732a0356f99e5e4d1ad62ab1ea516b81 upstream.
The recently added OPAL API call, OPAL_CONSOLE_FLUSH, originally took no
parameters and returned nothing. The call was updated to accept the
terminal number to flush, and returned various values depending on the
state of the output buffer.
The prototype has been updated and its usage in the OPAL kmsg dumper has
been modified to support its new behaviour as an incremental flush.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit affddff69c55eb68969448f35f59054a370bc7c1 upstream.
On BMC machines, console output is controlled by the OPAL firmware and is
only flushed when its pollers are called. When the kernel is in a panic
state, it no longer calls these pollers and thus console output does not
completely flush, causing some output from the panic to be lost.
Output is only actually lost when the kernel is configured to not power off
or reboot after panic (i.e. CONFIG_PANIC_TIMEOUT is set to 0) since OPAL
flushes the console buffer as part of its power down routines. Before this
patch, however, only partial output would be printed during the timeout wait.
This patch adds a new kmsg_dumper which gets called at panic time to ensure
panic output is not lost. It accomplishes this by calling OPAL_CONSOLE_FLUSH
in the OPAL API, and if that is not available, the pollers are called enough
times to (hopefully) completely flush the buffer.
The flushing mechanism will only affect output printed at and before the
kmsg_dump call in kernel/panic.c:panic(). As such, the "end Kernel panic"
message may still be truncated as follows:
>Call Trace:
>[c000000f1f603b00] [c0000000008e9458] dump_stack+0x90/0xbc (unreliable)
>[c000000f1f603b30] [c0000000008e7e78] panic+0xf8/0x2c4
>[c000000f1f603bc0] [c000000000be4860] mount_block_root+0x288/0x33c
>[c000000f1f603c80] [c000000000be4d14] prepare_namespace+0x1f4/0x254
>[c000000f1f603d00] [c000000000be43e8] kernel_init_freeable+0x318/0x350
>[c000000f1f603dc0] [c00000000000bd74] kernel_init+0x24/0x130
>[c000000f1f603e30] [c0000000000095b0] ret_from_kernel_thread+0x5c/0xac
>---[ end Kernel panic - not
This functionality is implemented as a kmsg_dumper as it seems to be the
most sensible way to introduce platform-specific functionality to the
panic function.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f15838e9cac8f78f0cc506529bb9d3b9fa589c1f upstream.
Since binutils 2.26 BFD is doing suffix merging on STRTAB sections. But
dedotify modifies the symbol names in place, which can also modify
unrelated symbols with a name that matches a suffix of a dotted name. To
remove the leading dot of a symbol name we can just increment the pointer
into the STRTAB section instead.
Backport to all stables to avoid breakage when people update their
binutils - mpe.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ccec44563b18a0ce90e2d4f332784b3cb25c8e9c upstream.
Thomas Huth discovered that a guest could cause a hard hang of a
host CPU by setting the Instruction Authority Mask Register (IAMR)
to a suitable value. It turns out that this is because when the
code was added to context-switch the new special-purpose registers
(SPRs) that were added in POWER8, we forgot to add code to ensure
that they were restored to a sane value on guest exit.
This adds code to set those registers where a bad value could
compromise the execution of the host kernel to a suitable neutral
value on guest exit.
Fixes: b005255e12
Reported-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6bf0fa14cf848ae770e0b7842c9b11ce2f01645 upstream.
During error recovery, the device could be removed as part of the
partial hotplug. The criterion used to come with partial hotplug
is: if the device driver provides error_detected(), slot_reset()
and resume() callbacks, it's immune from hotplug. Otherwise,
it's going to experience partial hotplug during EEH recovery. But
the criterion isn't correct enough: mlx4_core driver for Mellanox
adapters provides error_detected(), slot_reset() callbacks, but
resume() isn't there. Those Mellanox adapters won't be to involved
in the partial hotplug.
This fixes the criterion to a practical one: adpater with driver
that provides error_detected(), slot_reset() will be immune from
partial hotplug. resume() isn't mandatory.
Fixes: f2da4ccf ("powerpc/eeh: More relaxed hotplug criterion")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4d7f161feb3015d6306e1d35b565c888ff70c9d upstream.
The get and set operations got exchanged by mistake when moving the
code from book3s.c to powerpc.c.
Fixes: 3840edc803
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 760a7364f27d974d100118d88190e574626e18a6 upstream.
In the old DABR register, the BT (Breakpoint Translation) bit
is bit number 61. In the new DAWRX register, the WT (Watchpoint
Translation) bit is bit number 59. So to move the DABR-BT bit
into the position of the DAWRX-WT bit, it has to be shifted by
two, not only by one. This fixes hardware watchpoints in gdb of
older guests that only use the H_SET_DABR/X interface instead
of the new H_SET_MODE interface.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ecad912a0073c768db1491c27ca55ad2d0ee68f upstream.
Quite often drivers set only "write" permission assuming that this
includes "read" permission as well and this works on plenty of
platforms. However IODA2 is strict about this and produces an EEH when
"read" permission is not set and reading happens.
This adds a workaround in the IODA code to always add the "read" bit
when the "write" bit is set.
Fixes: 10b35b2b74 ("powerpc/powernv: Do not set "read" flag if direction==DMA_NONE")
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Tested-by: Douglas Miller <dougmill@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bc74f1ccd457832dc515fc1febe6655985fdcd2 upstream.
When PCI bus is unplugged during full hotplug for EEH recovery,
the platform PE instance (struct pnv_ioda_pe) isn't released and
it dereferences the stale PCI bus that has been released. It leads
to kernel crash when referring to the stale PCI bus.
This fixes the issue by correcting the PE's primary bus when it's
oneline at plugging time, in pnv_pci_dma_bus_setup() which is to
be called by pcibios_fixup_bus().
Reported-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reported-by: Pradipta Ghosh <pradghos@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05ba75f848647135f063199dc0e9f40fee769724 upstream.
When PE is created, its primary bus is cached to pe->bus. At later
point, the cached primary bus is returned from eeh_pe_bus_get().
However, we could get stale cached primary bus and run into kernel
crash in one case: full hotplug as part of fenced PHB error recovery
releases all PCI busses under the PHB at unplugging time and recreate
them at plugging time. pe->bus is still dereferencing the PCI bus
that was released.
This adds another PE flag (EEH_PE_PRI_BUS) to represent the validity
of pe->bus. pe->bus is updated when its first child EEH device is
online and the flag is set. Before unplugging in full hotplug for
error recovery, the flag is cleared.
Fixes: 8cdb2833 ("powerpc/eeh: Trace PCI bus from PE")
Reported-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reported-by: Pradipta Ghosh <pradghos@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e56f627768da4e6480986b5145dc3422bc448a5 upstream.
In eeh_pe_loc_get(), the PE location code is retrieved from the
"ibm,loc-code" property of the device node for the bridge of the
PE's primary bus. It's not correct because the property indicates
the parent PE's location code.
This reads the correct PE location code from "ibm,io-base-loc-code"
or "ibm,slot-location-code" property of PE parent bus's device node.
Fixes: 357b2f3dd9 ("powerpc/eeh: Dump PE location code")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a61674bdfc7c2bf909c4010699607b62b69b7bec upstream.
GCC 6 will include changes to generated code with -mcmodel=large,
which is used to build kernel modules on powerpc64le. This was
necessary because the large model is supposed to allow arbitrary
sizes and locations of the code and data sections, but the ELFv2
global entry point prolog still made the unconditional assumption
that the TOC associated with any particular function can be found
within 2 GB of the function entry point:
func:
addis r2,r12,(.TOC.-func)@ha
addi r2,r2,(.TOC.-func)@l
.localentry func, .-func
To remove this assumption, GCC will now generate instead this global
entry point prolog sequence when using -mcmodel=large:
.quad .TOC.-func
func:
.reloc ., R_PPC64_ENTRY
ld r2, -8(r12)
add r2, r2, r12
.localentry func, .-func
The new .reloc triggers an optimization in the linker that will
replace this new prolog with the original code (see above) if the
linker determines that the distance between .TOC. and func is in
range after all.
Since this new relocation is now present in module object files,
the kernel module loader is required to handle them too. This
patch adds support for the new relocation and implements the
same optimization done by the GNU linker.
Signed-off-by: Ulrich Weigand <ulrich.weigand@de.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81d7a3294de7e9828310bbf986a67246b13fa01e upstream.
According to memory-barriers.txt, xchg*, cmpxchg* and their atomic_
versions all need to be fully ordered, however they are now just
RELEASE+ACQUIRE, which are not fully ordered.
So also replace PPC_RELEASE_BARRIER and PPC_ACQUIRE_BARRIER with
PPC_ATOMIC_ENTRY_BARRIER and PPC_ATOMIC_EXIT_BARRIER in
__{cmp,}xchg_{u32,u64} respectively to guarantee fully ordered semantics
of atomic{,64}_{cmp,}xchg() and {cmp,}xchg(), as a complement of commit
b97021f855 ("powerpc: Fix atomic_xxx_return barrier semantics")
This patch depends on patch "powerpc: Make value-returning atomics fully
ordered" for PPC_ATOMIC_ENTRY_BARRIER definition.
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49e9cf3f0c04bf76ffa59242254110309554861d upstream.
According to memory-barriers.txt:
> Any atomic operation that modifies some state in memory and returns
> information about the state (old or new) implies an SMP-conditional
> general memory barrier (smp_mb()) on each side of the actual
> operation ...
Which mean these operations should be fully ordered. However on PPC,
PPC_ATOMIC_ENTRY_BARRIER is the barrier before the actual operation,
which is currently "lwsync" if SMP=y. The leading "lwsync" can not
guarantee fully ordered atomics, according to Paul Mckenney:
https://lkml.org/lkml/2015/10/14/970
To fix this, we define PPC_ATOMIC_ENTRY_BARRIER as "sync" to guarantee
the fully-ordered semantics.
This also makes futex atomics fully ordered, which can avoid possible
memory ordering problems if userspace code relies on futex system call
for fully ordered semantics.
Fixes: b97021f855 ("powerpc: Fix atomic_xxx_return barrier semantics")
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f821fc9c7 upstream.
Currently we can hit a scenario where we'll tm_reclaim() twice. This
results in a TM bad thing exception because the second reclaim occurs
when not in suspend mode.
The scenario in which this can happen is the following. We attempt to
deliver a signal to userspace. To do this we need obtain the stack
pointer to write the signal context. To get this stack pointer we
must tm_reclaim() in case we need to use the checkpointed stack
pointer (see get_tm_stackpointer()). Normally we'd then return
directly to userspace to deliver the signal without going through
__switch_to().
Unfortunatley, if at this point we get an error (such as a bad
userspace stack pointer), we need to exit the process. The exit will
result in a __switch_to(). __switch_to() will attempt to save the
process state which results in another tm_reclaim(). This
tm_reclaim() now causes a TM Bad Thing exception as this state has
already been saved and the processor is no longer in TM suspend mode.
Whee!
This patch checks the state of the MSR to ensure we are TM suspended
before we attempt the tm_reclaim(). If we've already saved the state
away, we should no longer be in TM suspend mode. This has the
additional advantage of checking for a potential TM Bad Thing
exception.
Found using syscall fuzzer.
Fixes: fb09692e71 ("powerpc: Add reclaim and recheckpoint functions for context switching transactional memory processes")
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SKF_AD_ALU_XOR_X ancillary is not like the other ancillary data
instructions since it XORs A with X while all the others replace A with
some loaded value. All the BPF JITs fail to clear A if this is used as
the first instruction in a filter. This was found using american fuzzy
lop.
Add a helper to determine if A needs to be cleared given the first
instruction in a filter, and use this in the JITs. Except for ARM, the
rest have only been compile-tested.
Fixes: 3480593131 ("net: filter: get rid of BPF_S_* enum")
Signed-off-by: Rabin Vincent <rabin@rab.in>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- A series of fixes to the MTRR emulation, tested in the BZ by several users
so they should be safe this late
- A fix for a division by zero
- Two very simple ARM and PPC fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJWeV/6AAoJEL/70l94x66DqzsH/05YnLi2GsX5WeZHMfIUgzgT
S/GoIkA7A4E2eXVoGg824MWppSViUzZkWgYFQTG4+KY9WPXzm9z2ij7DIlUHCD6n
QfevgQx1kIu1obyhm6bYM2xUdM3f7NCsQgw9bXZObB0ay+b/+GjR9/RbCbx60EO5
K1P+kveK6PFlS9/hc0PLztu6WkPV9BCO1RJUbeAEdnrMbpuQfHC+coR7MHRCiv2V
iy8f1CqrGaO5YPm9/3GbdH1xMKew4OZShOxTXwtvUThdrLkks2c8sk6FoLzqkznH
LMHVIpkm4mrIgThZG7VqZMXOrWvBtsCt04Vr9MzCM6QetB02b/Uz0xKvMYx2kZQ=
=pmYz
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
- A series of fixes to the MTRR emulation, tested in the BZ by several
users so they should be safe this late
- A fix for a division by zero
- Two very simple ARM and PPC fixes
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Reload pit counters for all channels when restoring state
KVM: MTRR: treat memory as writeback if MTRR is disabled in guest CPUID
KVM: MTRR: observe maxphyaddr from guest CPUID, not host
KVM: MTRR: fix fixed MTRR segment look up
KVM: VMX: Fix host initiated access to guest MSR_TSC_AUX
KVM: arm/arm64: vgic: Fix kvm_vgic_map_is_active's dist check
kvm: x86: move tracepoints outside extended quiescent state
KVM: PPC: Book3S HV: Prohibit setting illegal transaction state in MSR
Commit 25642e1459 ("powerpc/opal-irqchip: Fix double endian
conversion") fixed an endian bug by calling opal_handle_events() in
opal_event_unmask().
However this introduced a deadlock if we find an event is active
during unmasking and call opal_handle_events() again. The bad call
sequence is:
opal_interrupt()
-> opal_handle_events()
-> generic_handle_irq()
-> handle_level_irq()
-> raw_spin_lock(&desc->lock)
handle_irq_event(desc)
unmask_irq(desc)
-> opal_event_unmask()
-> opal_handle_events()
-> generic_handle_irq()
-> handle_level_irq()
-> raw_spin_lock(&desc->lock) (BOOM)
When generating multiple opal events in quick succession this would lead
to the following stall warnings:
EEH: Fenced PHB#0 detected, location: U78C9.001.WZS09XA-P1-C32
INFO: rcu_sched detected stalls on CPUs/tasks:
12-...: (1 GPs behind) idle=68f/140000000000001/0 softirq=860/861 fqs=2065
15-...: (1 GPs behind) idle=be5/140000000000001/0 softirq=1142/1143 fqs=2065
(detected by 13, t=2102 jiffies, g=1325, c=1324, q=602)
NMI watchdog: BUG: soft lockup - CPU#18 stuck for 22s! [irqbalance:2696]
INFO: rcu_sched detected stalls on CPUs/tasks:
12-...: (1 GPs behind) idle=68f/140000000000001/0 softirq=860/861 fqs=8371
15-...: (1 GPs behind) idle=be5/140000000000001/0 softirq=1142/1143 fqs=8371
(detected by 20, t=8407 jiffies, g=1325, c=1324, q=1290)
This patch corrects the problem by queuing the work if an event is
active during unmasking, which is similar to the pre-endian fix
behaviour.
Fixes: 25642e1459 ("powerpc/opal-irqchip: Fix double endian conversion")
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Reported-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When running on newer OPAL firmware that supports sending extra
OPAL_MSG types, we would print a warning on *every* message received.
This could be a problem for kernels that don't support OPAL_MSG_OCC
on machines that are running real close to thermal limits and the
OCC is throttling the chip. For a kernel that is paying attention to
the message queue, we could get these notifications quite often.
Conceivably, future message types could also come fairly often,
and printing that we didn't understand them 10,000 times provides
no further information than printing them once.
Cc: stable@vger.kernel.org
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This partially reverts commit a34236155a.
While reviewing the glibc patch to exploit the individual IPC calls,
Arnd & Andreas noticed that we were still requiring userspace to pass
IPC_64 in order to get the new style IPC API.
With a bit of cleanup in the kernel we can drop that requirement, and
instead only provide the new style API, which will simplify things for
userspace.
Rather than try and sneak that patch into 4.4, instead we will drop the
individual IPC calls for powerpc, and merge them again in 4.5 once the
cleanup patch has gone in.
Because we've already added sys_mlock2() as syscall #378, we don't do a
full revert of the IPC calls. Instead we drop the __NR #defines, and
send those now undefined syscall numbers to sys_ni_syscall(). This
leaves a gap in the syscall numbers, but we'll reuse them when we merge
the individual IPC calls.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Currently it is possible for userspace (e.g. QEMU) to set a value
for the MSR for a guest VCPU which has both of the TS bits set,
which is an illegal combination. The result of this is that when
we execute a hrfid (hypervisor return from interrupt doubleword)
instruction to enter the guest, the CPU will take a TM Bad Thing
type of program interrupt (vector 0x700).
Now, if PR KVM is configured in the kernel along with HV KVM, we
actually handle this without crashing the host or giving hypervisor
privilege to the guest; instead what happens is that we deliver a
program interrupt to the guest, with SRR0 reflecting the address
of the hrfid instruction and SRR1 containing the MSR value at that
point. If PR KVM is not configured in the kernel, then we try to
run the host's program interrupt handler with the MMU set to the
guest context, which almost certainly causes a host crash.
This closes the hole by making kvmppc_set_msr_hv() check for the
illegal combination and force the TS field to a safe value (00,
meaning non-transactional).
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit 527d10ef3a.
The reverted commit breaks cxlflash devices following an EEH reset (and
possibly other cxl devices, however this has not been tested).
The reverted commit changed the behaviour of eeh_reset_device() so that PHB
PEs are not unfrozen following the completion of the reset. This should not
be problematic, as no device resources should have been associated with the
PHB PE.
However, when attempting to load the cxlflash driver after a reset, the
driver attempts to read Vital Product Data through a call to
pci_read_vpd() (which is called on the physical cxl device, not on the
virtual AFU device). pci_read_vpd() in turn attempts to read from the cxl
device's config space. This fails, as the PE it's trying to read from is
still frozen. In turn, the driver gets an -ENODEV and fails to initialise.
It appears this issue only affects some parts of the VPD area, as "lspci
-vvv", which only reads a subset of the VPD bytes, is not broken by the
original patch.
At this stage, we don't fully understand why we're trying to read a frozen
PE, and we don't know how this affects other cxl devices. It is possible
that there is an underlying bug in the cxl driver or the powerpc CAPI
support code, or alternatively a bug in the PCI resource allocation/mapping
code that is incorrectly mapping resources to PE#0.
As such, this fix is incomplete, however it is necessary to prevent a
serious regression in CAPI support.
In the meantime, revert the commit, especially as it was intended to be a
non-functional change.
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Cc: Ian Munsie <imunsie@au1.ibm.com>
Cc: Daniel Axtens <dja@axtens.net>
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This file was originally cloned off of the MPC8641D-HPCN reference
platform, which actually had a PHY IRQ line connected. However this
board does not. The bogus entry was largely inert and went undetected
until commit 321beec504 ("net: phy: Use
interrupts when available in NOLINK state") was added to the tree.
With the above commit, the board fails to NFS boot since it sits waiting
for a PHY IRQ event that of course never arrives. Removing the bogus
entries from the DTS file fixes the issue.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The OPAL event calls return a mask of events that are active in big
endian format. This is checked when unmasking the events in the
irqchip by comparison with a cached value. The cached value was stored
in big endian format but should've been converted to CPU endian
first.
This bug leads to OPAL event delivery being delayed or dropped on some
systems. Symptoms may include a non-functional console.
The bug is fixed by calling opal_handle_events(...) instead of
duplicating code in opal_event_unmask(...).
Fixes: 9f0fd0499d ("powerpc/powernv: Add a virtual irqchip for opal events")
Cc: stable@vger.kernel.org # v4.2+
Reported-by: Douglas L Lehr <dllehr@us.ibm.com>
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently we can hit a scenario where we'll tm_reclaim() twice. This
results in a TM bad thing exception because the second reclaim occurs
when not in suspend mode.
The scenario in which this can happen is the following. We attempt to
deliver a signal to userspace. To do this we need obtain the stack
pointer to write the signal context. To get this stack pointer we
must tm_reclaim() in case we need to use the checkpointed stack
pointer (see get_tm_stackpointer()). Normally we'd then return
directly to userspace to deliver the signal without going through
__switch_to().
Unfortunatley, if at this point we get an error (such as a bad
userspace stack pointer), we need to exit the process. The exit will
result in a __switch_to(). __switch_to() will attempt to save the
process state which results in another tm_reclaim(). This
tm_reclaim() now causes a TM Bad Thing exception as this state has
already been saved and the processor is no longer in TM suspend mode.
Whee!
This patch checks the state of the MSR to ensure we are TM suspended
before we attempt the tm_reclaim(). If we've already saved the state
away, we should no longer be in TM suspend mode. This has the
additional advantage of checking for a potential TM Bad Thing
exception.
Found using syscall fuzzer.
Fixes: fb09692e71 ("powerpc: Add reclaim and recheckpoint functions for context switching transactional memory processes")
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently we allow both the MSR T and S bits to be set by userspace on
a signal return. Unfortunately this is a reserved configuration and
will cause a TM Bad Thing exception if attempted (via rfid).
This patch checks for this case in both the 32 and 64 bit signals
code. If both T and S are set, we mark the context as invalid.
Found using a syscall fuzzer.
Fixes: 2b0a576d15 ("powerpc: Add new transactional memory state to the signal context")
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- x86: work around two nasty cases where a benign exception occurs while
another is being delivered. The endless stream of exceptions causes an
infinite loop in the processor, which not even NMIs or SMIs can interrupt;
in the virt case, there is no possibility to exit to the host either.
- x86: support for Skylake per-guest TSC rate. Long supported by AMD,
the patches mostly move things from there to common arch/x86/kvm/ code.
- generic: remove local_irq_save/restore from the guest entry and exit
paths when context tracking is enabled. The patches are a few months
old, but we discussed them again at kernel summit. Andy will pick up
from here and, in 4.5, try to remove it from the user entry/exit paths.
- PPC: Two bug fixes, see merge commit 370289756b for details.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJWRFb0AAoJEL/70l94x66DjjMH/31jr8d119MW0uv2x+03+wRq
6dbJ8tjQ8grvBRExKvLsUVjDmHlhCa1BQl5qjCsyYhX9UeAf4NQOmoEFpq+YTLxh
Ctveyn+yiZWC7qxbQDmauiQ4JCOp+W9ial782iqw5+ouQMajGOffq5WrojCa2ZNF
jI278JgdHJLrKj/uie//WBu3V7MJY5Apc3p4zatnSYFSQ3MA0sxl4r4zIrwOa5qs
23ZeeoqbP4sHh4X5wL/30Y6XFSCHj0qoYHHyAgzLi0PCMvBdt4DrAFUPDG/Rhlv6
o1WB/kcUfcz3DtBX85wfSOMuw0nF6patWhWv07R/3EIbYoz3dKvp9d6ORYgXqlY=
=Um9M
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull second batch of kvm updates from Paolo Bonzini:
"Four changes:
- x86: work around two nasty cases where a benign exception occurs
while another is being delivered. The endless stream of exceptions
causes an infinite loop in the processor, which not even NMIs or
SMIs can interrupt; in the virt case, there is no possibility to
exit to the host either.
- x86: support for Skylake per-guest TSC rate. Long supported by
AMD, the patches mostly move things from there to common
arch/x86/kvm/ code.
- generic: remove local_irq_save/restore from the guest entry and
exit paths when context tracking is enabled. The patches are a few
months old, but we discussed them again at kernel summit. Andy
will pick up from here and, in 4.5, try to remove it from the user
entry/exit paths.
- PPC: Two bug fixes, see merge commit 370289756b for details"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (21 commits)
KVM: x86: rename update_db_bp_intercept to update_bp_intercept
KVM: svm: unconditionally intercept #DB
KVM: x86: work around infinite loop in microcode when #AC is delivered
context_tracking: avoid irq_save/irq_restore on guest entry and exit
context_tracking: remove duplicate enabled check
KVM: VMX: Dump TSC multiplier in dump_vmcs()
KVM: VMX: Use a scaled host TSC for guest readings of MSR_IA32_TSC
KVM: VMX: Setup TSC scaling ratio when a vcpu is loaded
KVM: VMX: Enable and initialize VMX TSC scaling
KVM: x86: Use the correct vcpu's TSC rate to compute time scale
KVM: x86: Move TSC scaling logic out of call-back read_l1_tsc()
KVM: x86: Move TSC scaling logic out of call-back adjust_tsc_offset()
KVM: x86: Replace call-back compute_tsc_offset() with a common function
KVM: x86: Replace call-back set_tsc_khz() with a common function
KVM: x86: Add a common TSC scaling function
KVM: x86: Add a common TSC scaling ratio field in kvm_vcpu_arch
KVM: x86: Collect information for setting TSC scaling ratio
KVM: x86: declare a few variables as __read_mostly
KVM: x86: merge handle_mmio_page_fault and handle_mmio_page_fault_common
KVM: PPC: Book3S HV: Don't dynamically split core when already split
...
Pull block IO poll support from Jens Axboe:
"Various groups have been doing experimentation around IO polling for
(really) fast devices. The code has been reviewed and has been
sitting on the side for a few releases, but this is now good enough
for coordinated benchmarking and further experimentation.
Currently O_DIRECT sync read/write are supported. A framework is in
the works that allows scalable stats tracking so we can auto-tune
this. And we'll add libaio support as well soon. Fow now, it's an
opt-in feature for test purposes"
* 'for-4.4/io-poll' of git://git.kernel.dk/linux-block:
direct-io: be sure to assign dio->bio_bdev for both paths
directio: add block polling support
NVMe: add blk polling support
block: add block polling support
blk-mq: return tag/queue combo in the make_request_fn handlers
block: change ->make_request_fn() and users to return a queue cookie
Removal started in commit 5bbeed12bd ("sparc32: drop unused
kmap_atomic_to_page"). Let's do it across the whole tree.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No functional changes in this patch, but it prepares us for returning
a more useful cookie related to the IO that was queued up.
Signed-off-by: Jens Axboe <axboe@fb.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Keith Busch <keith.busch@intel.com>
- Kconfig: remove BE-only platforms from LE kernel build from Boqun Feng
- Refresh ps3_defconfig from Geoff Levand
- Emit GNU & SysV hashes for the vdso from Michael Ellerman
- Define an enum for the bolted SLB indexes from Anshuman Khandual
- Use a local to avoid multiple calls to get_slb_shadow() from Michael Ellerman
- Add gettimeofday() benchmark from Michael Neuling
- Avoid link stack corruption in __get_datapage() from Michael Neuling
- Add virt_to_pfn and use this instead of opencoding from Aneesh Kumar K.V
- Add ppc64le_defconfig from Michael Ellerman
- pseries: extract of_helpers module from Andy Shevchenko
- Correct string length in pseries_of_derive_parent() from Nathan Fontenot
- Free the MSI bitmap if it was slab allocated from Denis Kirjanov
- Shorten irq_chip name for the SIU from Christophe Leroy
- Wait 1s for secondaries to enter OPAL during kexec from Samuel Mendoza-Jonas
- Fix _ALIGN_* errors due to type difference. from Aneesh Kumar K.V
- powerpc/pseries/hvcserver: don't memset pi_buff if it is null from Colin Ian King
- Disable hugepd for 64K page size. from Aneesh Kumar K.V
- Differentiate between hugetlb and THP during page walk from Aneesh Kumar K.V
- Make PCI non-optional for pseries from Michael Ellerman
- Individual System V IPC system calls from Sam bobroff
- Add selftest of unmuxed IPC calls from Michael Ellerman
- discard .exit.data at runtime from Stephen Rothwell
- Delete old orphaned PrPMC 280/2800 DTS and boot file. from Paul Gortmaker
- Use of_get_next_parent to simplify code from Christophe Jaillet
- Paginate some xmon output from Sam bobroff
- Add some more elements to the xmon PACA dump from Michael Ellerman
- Allow the tm-syscall selftest to build with old headers from Michael Ellerman
- Run EBB selftests only on POWER8 from Denis Kirjanov
- Drop CONFIG_TUNE_CELL in favour of CONFIG_CELL_CPU from Michael Ellerman
- Avoid reference to potentially freed memory in prom.c from Christophe Jaillet
- Quieten boot wrapper output with run_cmd from Geoff Levand
- EEH fixes and cleanups from Gavin Shan
- Fix recursive fenced PHB on Broadcom shiner adapter from Gavin Shan
- Use of_get_next_parent() in of_get_ibm_chip_id() from Michael Ellerman
- Fix section mismatch warning in msi_bitmap_alloc() from Denis Kirjanov
- Fix ps3-lpm white space from Rudhresh Kumar J
- Fix ps3-vuart null dereference from Colin King
- nvram: Add missing kfree in error path from Christophe Jaillet
- nvram: Fix function name in some errors messages. from Christophe Jaillet
- drivers/macintosh: adb: fix misleading Kconfig help text from Aaro Koskinen
- agp/uninorth: fix a memleak in create_gatt_table from Denis Kirjanov
- cxl: Free virtual PHB when removing from Andrew Donnellan
- scripts/kconfig/Makefile: Allow KBUILD_DEFCONFIG to be a target from Michael Ellerman
- scripts/kconfig/Makefile: Fix KBUILD_DEFCONFIG check when building with O= from Michael Ellerman
- Freescale updates from Scott: Highlights include 64-bit book3e kexec/kdump
support, a rework of the qoriq clock driver, device tree changes including
qoriq fman nodes, support for a new 85xx board, and some fixes.
- MPC5xxx updates from Anatolij: Highlights include a driver for MPC512x
LocalPlus Bus FIFO with its device tree binding documentation, mpc512x
device tree updates and some minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YwcM
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Kconfig: remove BE-only platforms from LE kernel build from Boqun
Feng
- Refresh ps3_defconfig from Geoff Levand
- Emit GNU & SysV hashes for the vdso from Michael Ellerman
- Define an enum for the bolted SLB indexes from Anshuman Khandual
- Use a local to avoid multiple calls to get_slb_shadow() from Michael
Ellerman
- Add gettimeofday() benchmark from Michael Neuling
- Avoid link stack corruption in __get_datapage() from Michael Neuling
- Add virt_to_pfn and use this instead of opencoding from Aneesh Kumar
K.V
- Add ppc64le_defconfig from Michael Ellerman
- pseries: extract of_helpers module from Andy Shevchenko
- Correct string length in pseries_of_derive_parent() from Nathan
Fontenot
- Free the MSI bitmap if it was slab allocated from Denis Kirjanov
- Shorten irq_chip name for the SIU from Christophe Leroy
- Wait 1s for secondaries to enter OPAL during kexec from Samuel
Mendoza-Jonas
- Fix _ALIGN_* errors due to type difference, from Aneesh Kumar K.V
- powerpc/pseries/hvcserver: don't memset pi_buff if it is null from
Colin Ian King
- Disable hugepd for 64K page size, from Aneesh Kumar K.V
- Differentiate between hugetlb and THP during page walk from Aneesh
Kumar K.V
- Make PCI non-optional for pseries from Michael Ellerman
- Individual System V IPC system calls from Sam bobroff
- Add selftest of unmuxed IPC calls from Michael Ellerman
- discard .exit.data at runtime from Stephen Rothwell
- Delete old orphaned PrPMC 280/2800 DTS and boot file, from Paul
Gortmaker
- Use of_get_next_parent to simplify code from Christophe Jaillet
- Paginate some xmon output from Sam bobroff
- Add some more elements to the xmon PACA dump from Michael Ellerman
- Allow the tm-syscall selftest to build with old headers from Michael
Ellerman
- Run EBB selftests only on POWER8 from Denis Kirjanov
- Drop CONFIG_TUNE_CELL in favour of CONFIG_CELL_CPU from Michael
Ellerman
- Avoid reference to potentially freed memory in prom.c from Christophe
Jaillet
- Quieten boot wrapper output with run_cmd from Geoff Levand
- EEH fixes and cleanups from Gavin Shan
- Fix recursive fenced PHB on Broadcom shiner adapter from Gavin Shan
- Use of_get_next_parent() in of_get_ibm_chip_id() from Michael
Ellerman
- Fix section mismatch warning in msi_bitmap_alloc() from Denis
Kirjanov
- Fix ps3-lpm white space from Rudhresh Kumar J
- Fix ps3-vuart null dereference from Colin King
- nvram: Add missing kfree in error path from Christophe Jaillet
- nvram: Fix function name in some errors messages, from Christophe
Jaillet
- drivers/macintosh: adb: fix misleading Kconfig help text from Aaro
Koskinen
- agp/uninorth: fix a memleak in create_gatt_table from Denis Kirjanov
- cxl: Free virtual PHB when removing from Andrew Donnellan
- scripts/kconfig/Makefile: Allow KBUILD_DEFCONFIG to be a target from
Michael Ellerman
- scripts/kconfig/Makefile: Fix KBUILD_DEFCONFIG check when building
with O= from Michael Ellerman
- Freescale updates from Scott: Highlights include 64-bit book3e
kexec/kdump support, a rework of the qoriq clock driver, device tree
changes including qoriq fman nodes, support for a new 85xx board, and
some fixes.
- MPC5xxx updates from Anatolij: Highlights include a driver for
MPC512x LocalPlus Bus FIFO with its device tree binding
documentation, mpc512x device tree updates and some minor fixes.
* tag 'powerpc-4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (106 commits)
powerpc/msi: Fix section mismatch warning in msi_bitmap_alloc()
powerpc/prom: Use of_get_next_parent() in of_get_ibm_chip_id()
powerpc/pseries: Correct string length in pseries_of_derive_parent()
powerpc/e6500: hw tablewalk: make sure we invalidate and write to the same tlb entry
powerpc/mpc85xx: Add FSL QorIQ DPAA FMan support to the SoC device tree(s)
powerpc/mpc85xx: Create dts components for the FSL QorIQ DPAA FMan
powerpc/fsl: Add #clock-cells and clockgen label to clockgen nodes
powerpc: handle error case in cpm_muram_alloc()
powerpc: mpic: use IRQCHIP_SKIP_SET_WAKE instead of redundant mpic_irq_set_wake
powerpc/book3e-64: Enable kexec
powerpc/book3e-64/kexec: Set "r4 = 0" when entering spinloop
powerpc/booke: Only use VIRT_PHYS_OFFSET on booke32
powerpc/book3e-64/kexec: Enable SMP release
powerpc/book3e-64/kexec: create an identity TLB mapping
powerpc/book3e-64: Don't limit paca to 256 MiB
powerpc/book3e/kdump: Enable crash_kexec_wait_realmode
powerpc/book3e: support CONFIG_RELOCATABLE
powerpc/booke64: Fix args to copy_and_flush
powerpc/book3e-64: rename interrupt_end_book3e with __end_interrupts
powerpc/e6500: kexec: Handle hardware threads
...
Merge patch-bomb from Andrew Morton:
- inotify tweaks
- some ocfs2 updates (many more are awaiting review)
- various misc bits
- kernel/watchdog.c updates
- Some of mm. I have a huge number of MM patches this time and quite a
lot of it is quite difficult and much will be held over to next time.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (162 commits)
selftests: vm: add tests for lock on fault
mm: mlock: add mlock flags to enable VM_LOCKONFAULT usage
mm: introduce VM_LOCKONFAULT
mm: mlock: add new mlock system call
mm: mlock: refactor mlock, munlock, and munlockall code
kasan: always taint kernel on report
mm, slub, kasan: enable user tracking by default with KASAN=y
kasan: use IS_ALIGNED in memory_is_poisoned_8()
kasan: Fix a type conversion error
lib: test_kasan: add some testcases
kasan: update reference to kasan prototype repo
kasan: move KASAN_SANITIZE in arch/x86/boot/Makefile
kasan: various fixes in documentation
kasan: update log messages
kasan: accurately determine the type of the bad access
kasan: update reported bug types for kernel memory accesses
kasan: update reported bug types for not user nor kernel memory accesses
mm/kasan: prevent deadlock in kasan reporting
mm/kasan: don't use kasan shadow pointer in generic functions
mm/kasan: MODULE_VADDR is not available on all archs
...
In static micro-threading modes, the dynamic micro-threading code
is supposed to be disabled, because subcores can't make independent
decisions about what micro-threading mode to put the core in - there is
only one micro-threading mode for the whole core. The code that
implements dynamic micro-threading checks for this, except that the
check was missed in one case. This means that it is possible for a
subcore in static 2-way micro-threading mode to try to put the core
into 4-way micro-threading mode, which usually leads to stuck CPUs,
spinlock lockups, and other stalls in the host.
The problem was in the can_split_piggybacked_subcores() function, which
should always return false if the system is in a static micro-threading
mode. This fixes the problem by making can_split_piggybacked_subcores()
use subcore_config_ok() for its checks, as subcore_config_ok() includes
the necessary check for the static micro-threading modes.
Credit to Gautham Shenoy for working out that the reason for the hangs
and stalls we were seeing was that we were trying to do dynamic 4-way
micro-threading while we were in static 2-way mode.
Fixes: b4deba5c41
Cc: vger@stable.kernel.org # v4.3
Signed-off-by: Paul Mackerras <paulus@samba.org>
When handling a hypervisor data or instruction storage interrupt (HDSI
or HISI), we look up the SLB entry for the address being accessed in
order to translate the effective address to a virtual address which can
be looked up in the guest HPT. This lookup can occasionally fail due
to the guest replacing an SLB entry without invalidating the evicted
SLB entry. In this situation an ERAT (effective to real address
translation cache) entry can persist and be used by the hardware even
though there is no longer a corresponding SLB entry.
Previously we would just deliver a data or instruction storage interrupt
(DSI or ISI) to the guest in this case. However, this is not correct
and has been observed to cause guests to crash, typically with a
data storage protection interrupt on a store to the vmemmap area.
Instead, what we do now is to synthesize a data or instruction segment
interrupt. That should cause the guest to reload an appropriate entry
into the SLB and retry the faulting instruction. If it still faults,
we should find an appropriate SLB entry next time and be able to handle
the fault.
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The previous patch introduced a flag that specified pages in a VMA should
be placed on the unevictable LRU, but they should not be made present when
the area is created. This patch adds the ability to set this state via
the new mlock system calls.
We add MLOCK_ONFAULT for mlock2 and MCL_ONFAULT for mlockall.
MLOCK_ONFAULT will set the VM_LOCKONFAULT modifier for VM_LOCKED.
MCL_ONFAULT should be used as a modifier to the two other mlockall flags.
When used with MCL_CURRENT, all current mappings will be marked with
VM_LOCKED | VM_LOCKONFAULT. When used with MCL_FUTURE, the mm->def_flags
will be marked with VM_LOCKED | VM_LOCKONFAULT. When used with both
MCL_CURRENT and MCL_FUTURE, all current mappings and mm->def_flags will be
marked with VM_LOCKED | VM_LOCKONFAULT.
Prior to this patch, mlockall() will unconditionally clear the
mm->def_flags any time it is called without MCL_FUTURE. This behavior is
maintained after adding MCL_ONFAULT. If a call to mlockall(MCL_FUTURE) is
followed by mlockall(MCL_CURRENT), the mm->def_flags will be cleared and
new VMAs will be unlocked. This remains true with or without MCL_ONFAULT
in either mlockall() invocation.
munlock() will unconditionally clear both vma flags. munlockall()
unconditionally clears for VMA flags on all VMAs and in the mm->def_flags
field.
Signed-off-by: Eric B Munson <emunson@akamai.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the setup_nr_nodes(), we have already initialized
node_possible_map. So it is safe to use for_each_node here.
There are many places in the kernel that use hardcoded 'for' loop with
nr_node_ids, because all other architectures have numa nodes populated
serially. That should be reason we had maintained the same for
powerpc.
But, since sparse numa node ids possible on powerpc, we unnecessarily
allocate memory for non existent numa nodes.
For e.g., on a system with 0,1,16,17 as numa nodes nr_node_ids=18 and
we allocate memory for nodes 2-14. This patch we allocate memory for
only existing numa nodes.
The patch is boot tested on a 4 node tuleta, confirming with printks
that it works as expected.
Signed-off-by: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Cc: Vladimir Davydov <vdavydov@parallels.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Anton Blanchard <anton@samba.org>
Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Greg Kurz <gkurz@linux.vnet.ibm.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
probe_kernel_address() is basically the same as the (later added)
probe_kernel_read().
The return value on EFAULT is a bit different: probe_kernel_address()
returns number-of-bytes-not-copied whereas probe_kernel_read() returns
-EFAULT. All callers have been checked, none cared.
probe_kernel_read() can be overridden by the architecture whereas
probe_kernel_address() cannot. parisc, blackfin and um do this, to insert
additional checking. Hence this patch possibly fixes obscure bugs,
although there are only two probe_kernel_address() callsites outside
arch/.
My first attempt involved removing probe_kernel_address() entirely and
converting all callsites to use probe_kernel_read() directly, but that got
tiresome.
This patch shrinks mm/slab_common.o by 218 bytes. For a single
probe_kernel_address() callsite.
Cc: Steven Miao <realmz6@gmail.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
