[ Upstream commit a3a5129e122709306cfa6409781716c2933df99b ]
Consider the following situation which has been found in a test setup:
Gateway B has claimed client C and gateway A has the same backbone
network as B. C sends a broad- or multicast to B and directly after
this packet decides to send another packet to A due to a better TQ
value. B will forward the broad-/multicast into the backbone as it is
the responsible gw and after that A will claim C as it has been
chosen by C as the best gateway. If it now happens that A claims C
before it has received the broad-/multicast forwarded by B (due to
backbone topology or due to some delay in B when forwarding the
packet) we get a critical situation: in the current code A will
immediately unclaim C when receiving the multicast due to the
roaming client scenario although the position of C has not changed
in the mesh. If this happens the multi-/broadcast forwarded by B
will be sent back into the mesh by A and we have looping packets
until one of the gateways claims C again.
In order to prevent this, unclaiming of a client due to the roaming
client scenario is only done after a certain time is expired after
the last claim of the client. 100 ms are used here, which should be
slow enough for big backbones and slow gateways but fast enough not
to break the roaming client use case.
Acked-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Andreas Pape <apape@phoenixcontact.com>
[sven@narfation.org: fix conflicts with current version]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2d0f48a13e53b4747704c9e692f5e765e52041a upstream.
batadv_tt_prepare_tvlv_local_data can fail to allocate the memory for the
new TVLV block. The caller is informed about this problem with the returned
length of 0. Not checking this value results in an invalid memory access
when either tt_data or tt_change is accessed.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 7ea7b4a142 ("batman-adv: make the TT CRC logic VLAN specific")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9f179877e50ae2681fe7b0b83e0d9f63b6165ad upstream.
Reported-by: Lars Bußmann <ffsoest@kill-you.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
[sven@narfation.org: rewritten commit message to make clear that it is an
bugfix to an user reported crash]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1a65f1741bfd9c69f9e4e2ad447a89b6810427d upstream.
_batadv_update_route rcu_derefences orig_ifinfo->router outside of a
spinlock protected region to print some information messages to the debug
log. But this pointer is not checked again when the new pointer is assigned
in the spinlock protected region. Thus is can happen that the value of
orig_ifinfo->router changed in the meantime and thus the reference counter
of the wrong router gets reduced after the spinlock protected region.
Just rcu_dereferencing the value of orig_ifinfo->router inside the spinlock
protected region (which also set the new pointer) is enough to get the
correct old router object.
Fixes: e1a5382f97 ("batman-adv: Make orig_node->router an rcu protected pointer")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4fdb6cff2aa0ae740c5f19b6f745cbbe786d42f upstream.
When removing a single interface while a broadcast or ogm packet is
still pending then we will free the forward packet without releasing the
queue slots again.
This patch is supposed to fix this issue.
Fixes: 6d5808d4ae ("batman-adv: Add missing hardif_free_ref in forw_packet_free")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
[sven@narfation.org: fix conflicts with current version]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c78296665c3d81f040117432ab9e1cb125521b0c upstream.
The encapsulated ethernet and VLAN header may be outside the received
ethernet frame. Thus the skb buffer size has to be checked before it can be
parsed to find out if it encapsulates another batman-adv packet.
Fixes: 420193573f ("batman-adv: softif bridge loop avoidance")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2871734e85e920503d49b3a8bc0afbe0773b6036 upstream.
Now that DAT is VLAN aware, it must use the VID when
computing the DHT address of the candidate nodes where
an entry is going to be stored/retrieved.
Fixes: be1db4f661 ("batman-adv: make the Distributed ARP Table vlan aware")
Signed-off-by: Antonio Quartulli <a@unstable.cc>
[sven@narfation.org: fix conflicts with current version]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 42eff6a617e23b691f8e4467f4687ed7245a92db ]
It is not allowed to free the memory of an object which is part of a list
which is protected by rcu-read-side-critical sections without making sure
that no other context is accessing the object anymore. This usually happens
by removing the references to this object and then waiting until the rcu
grace period is over and no one (allowedly) accesses it anymore.
But the _now functions ignore this completely. They free the object
directly even when a different context still tries to access it. This has
to be avoided and thus these functions must be removed and all functions
have to use batadv_orig_node_free_ref.
Fixes: 72822225bd ("batman-adv: Fix rcu_barrier() miss due to double call_rcu() in TT code")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b4d922cfc9c08318eeb77d53b7633740e6b0efb0 ]
It is not allowed to free the memory of an object which is part of a list
which is protected by rcu-read-side-critical sections without making sure
that no other context is accessing the object anymore. This usually happens
by removing the references to this object and then waiting until the rcu
grace period is over and no one (allowedly) accesses it anymore.
But the _now functions ignore this completely. They free the object
directly even when a different context still tries to access it. This has
to be avoided and thus these functions must be removed and all functions
have to use batadv_hardif_free_ref.
Fixes: 89652331c0 ("batman-adv: split tq information in neigh_node struct")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ae3e1e36e3cb6c686a7a2725af20ca86aa46d62a ]
It is not allowed to free the memory of an object which is part of a list
which is protected by rcu-read-side-critical sections without making sure
that no other context is accessing the object anymore. This usually happens
by removing the references to this object and then waiting until the rcu
grace period is over and no one (allowedly) accesses it anymore.
But the _now functions ignore this completely. They free the object
directly even when a different context still tries to access it. This has
to be avoided and thus these functions must be removed and all functions
have to use batadv_neigh_ifinfo_free_ref.
Fixes: 89652331c0 ("batman-adv: split tq information in neigh_node struct")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2baa753c276f27f8e844637561ad597867aa6fb6 ]
It is not allowed to free the memory of an object which is part of a list
which is protected by rcu-read-side-critical sections without making sure
that no other context is accessing the object anymore. This usually happens
by removing the references to this object and then waiting until the rcu
grace period is over and no one (allowedly) accesses it anymore.
But the _now functions ignore this completely. They free the object
directly even when a different context still tries to access it. This has
to be avoided and thus these functions must be removed and all functions
have to use batadv_neigh_node_free_ref.
Fixes: 89652331c0 ("batman-adv: split tq information in neigh_node struct")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit deed96605f5695cb945e0b3d79429581857a2b9d ]
It is not allowed to free the memory of an object which is part of a list
which is protected by rcu-read-side-critical sections without making sure
that no other context is accessing the object anymore. This usually happens
by removing the references to this object and then waiting until the rcu
grace period is over and no one (allowedly) accesses it anymore.
But the _now functions ignore this completely. They free the object
directly even when a different context still tries to access it. This has
to be avoided and thus these functions must be removed and all functions
have to use batadv_orig_ifinfo_free_ref.
Fixes: 7351a4822d ("batman-adv: split out router from orig_node")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 44e8e7e91d6c7c7ab19688750f7257292640d1a0 ]
The batadv_nc_node_free_ref function uses call_rcu to delay the free of the
batadv_nc_node object until no (already started) rcu_read_lock is enabled
anymore. This makes sure that no context is still trying to access the
object which should be removed. But batadv_nc_node also contains a
reference to orig_node which must be removed.
The reference drop of orig_node was done in the call_rcu function
batadv_nc_node_free_rcu but should actually be done in the
batadv_nc_node_release function to avoid nested call_rcus. This is
important because rcu_barrier (e.g. batadv_softif_free or batadv_exit) will
not detect the inner call_rcu as relevant for its execution. Otherwise this
barrier will most likely be inserted in the queue before the callback of
the first call_rcu was executed. The caller of rcu_barrier will therefore
continue to run before the inner call_rcu callback finished.
Fixes: d56b1705e2 ("batman-adv: network coding - detect coding nodes and remove these after timeout")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 63b399272294e7a939cde41792dca38c549f0484 ]
The batadv_claim_free_ref function uses call_rcu to delay the free of the
batadv_bla_claim object until no (already started) rcu_read_lock is enabled
anymore. This makes sure that no context is still trying to access the
object which should be removed. But batadv_bla_claim also contains a
reference to backbone_gw which must be removed.
The reference drop of backbone_gw was done in the call_rcu function
batadv_claim_free_rcu but should actually be done in the
batadv_claim_release function to avoid nested call_rcus. This is important
because rcu_barrier (e.g. batadv_softif_free or batadv_exit) will not
detect the inner call_rcu as relevant for its execution. Otherwise this
barrier will most likely be inserted in the queue before the callback of
the first call_rcu was executed. The caller of rcu_barrier will therefore
continue to run before the inner call_rcu callback finished.
Fixes: 23721387c4 ("batman-adv: add basic bridge loop avoidance code")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
batadv_dat_select_candidates provides an u32 to batadv_hash_dat but it
needs a batadv_dat_entry with at least ip and vid filled in.
Fixes: 3e26722bc9f2 ("batman-adv: make the Distributed ARP Table vlan aware")
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
Acked-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The translation table implementation, namely batadv_compare_tt(),
is used to compare two client entries and deciding if they are the
holding the same information. Each client entry is identified by
its mac address and its VLAN id (VID).
Consequently, batadv_compare_tt() has to not only compare the mac
addresses but also the VIDs.
Without this fix adding a new client entry that possesses the same
mac address as another client but operates on a different VID will
fail because both client entries will considered identical.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
In the case when a temporary entry is added first and a proper tt entry
is added after that, the temporary tt entry is kept in the orig list.
However the temporary flag is removed at this point, and therefore the
purge function can not find this temporary entry anymore.
Therefore, remove the previous temp entry before adding the new proper
one.
This case can happen if a client behind a given originator moves before
the TT announcement is sent out. Other than that, this case can also be
created by bogus or malicious payload frames for VLANs which are not
existent on the sending originator.
Reported-by: Alessandro Bolletta <alessandro@mediaspot.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Acked-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
DAT Cache replies are answered on behalf of other clients which are not
connected to the answering originator. Therefore, we shouldn't add these
clients to the answering originators TT table through speed join to
avoid bogus entries.
Reported-by: Alessandro Bolletta <alessandro@mediaspot.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Acked-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
commit c214ebe1eb29 ("batman-adv: move neigh_node list add into
batadv_neigh_node_new()") removed external calls to
batadv_neigh_node_get().
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The maximum of hard_header_len and maximum of all needed_(head|tail)room of
all slave interfaces of a batman-adv device must be used to define the
batman-adv device needed_(head|tail)room. This is required to avoid too
small buffer problems when these slave devices try to send the encapsulated
packet in a tx path without the possibility to resize the skbuff.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
In batadv_hardif_disable_interface() there is a call to
batadv_softif_destroy_sysfs() which in turns invokes
unregister_netdevice() on the soft_iface.
After this point we cannot rely on the soft_iface object
anymore because it might get free'd by the netdev periodic
routine at any time.
For this reason the netdev_upper_dev_unlink(.., soft_iface) call
is moved before the invocation of batadv_softif_destroy_sysfs() so
that we can be sure that the soft_iface object is still valid.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
commit 0511575c4d03 ("batman-adv: remove obsolete deleted attribute for
gateway node") incorrectly added an empy line and forgot to remove an
include.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Acked-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
With rcu, the gateway node deleted attribute is not needed anymore. In
fact, it may delay the free of the gateway node and its referenced
structures. Therefore remove it altogether and simplify purging as well.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
All batadv_neigh_node_* functions expect the neigh_node list item to be part
of the orig_node->neigh_list, therefore the constructor of said list item
should be adding the newly created neigh_node to the respective list.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Acked-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The batadv_neigh_node_new() function already sets the hard_iface pointer.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Acked-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The batadv_neigh_node cleanup function 'batadv_neigh_node_free_rcu()'
takes care of reducing the hardif refcounter, hence it's only logical
to assume the creating function of that same object
'batadv_neigh_node_new()' takes care of increasing the same refcounter.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Acked-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Some functions already have documentation about locks they require inside
their kerneldoc header. These can be directly tested during runtime using
the lockdep asserts.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Functions which use (h)list_del* are requiring correct locking when they
operate on global lists. Most of the time the search in the list and the
delete are done in the same function. All other cases should have it
visible that they require a special lock to avoid race conditions.
Lockdep asserts can be used to check these problem during runtime when the
lockdep functionality is enabled.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Since the list's tail is never accessed using a double linked list head
wastes memory.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The TVLV for the gw_bandwidth stores everything as u32. But the
gw_bandwidth reads the signed long which limits the maximum value to
(2 ** 31 - 1) on systems with 4 byte long. Also the input value is always
converted from either Mibit/s or Kibit/s to 100Kibit/s. This reduces the
values even further when the user sets it via the default unit Kibit/s. It
may even cause an integer overflow and end up with a value the user never
intended.
Instead read the values as u64, check for possible overflows, do the unit
adjustments and then reduce the size to u32.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Invalid speed settings by the user are currently acknowledged as correct
but not stored. Instead the return of the store operation of the file
"gw_bandwidth" should indicate that the given value is not acceptable.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The hlist_del_rcu() call in batadv_tt_global_size_mod() does not check
if the element still is part of the list prior to deletion. The atomic
list counter should prevent the worst but converting to
hlist_del_init_rcu() ensures the element can't be deleted more than
once.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Since the list's tail is never accessed using a double linked list head
wastes memory.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
main.h is included in every file and is the only way to access types.h.
This makes forward declarations for all types defined in types.h
unnecessary.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The updated kernel doc & additional comment shall prevent accidental
copy & paste errors or calling the function without the required
precautions.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The Linux CodingStyle disallows multiple assignments in a single line.
(see chapter 1)
Reported-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Kerneldoc required single line documentation in the past (before 2009).
Therefore, the 80 columns limit per line check of checkpatch was disabled
for kerneldoc. But kerneldoc is not excluded anymore from it and checkpatch
now enabled the check again.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
(s|u)(8|16|32|64) are the preferred types in the kernel. The use of the
standard C99 types u?int(8|16|32|64)_t are objected by some people and even
checkpatch now warns about using them.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The object tt_local is allocated with kmalloc and not initialized when the
function batadv_tt_local_add checks for the vlan. But this function can
only cleanup the object when the (not yet initialized) reference counter of
the object is 1. This is unlikely and thus the object would leak when the
vlan could not be found.
Instead the uninitialized object tt_local has to be freed manually and the
pointer has to set to NULL to avoid calling the function which would try to
decrement the reference counter of the not existing object.
CID: 1316518
Fixes: 354136bcc3 ("batman-adv: fix kernel crash due to missing NULL checks")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Cc: Marek Lindner <mareklindner@neomailbox.ch>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- avoid integer overflow in GW selection routine
- prevent race condition by making capability bit changes atomic (use
clear/set/test_bit)
- fix synchronization issue in mcast tvlv handler
- fix crash on double list removal of TT Request objects
- fix leak by puring packets enqueued for sending upon iface removal
- ensure network header pointer is set in skb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ZEuN
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
Included changes:
- avoid integer overflow in GW selection routine
- prevent race condition by making capability bit changes atomic (use
clear/set/test_bit)
- fix synchronization issue in mcast tvlv handler
- fix crash on double list removal of TT Request objects
- fix leak by puring packets enqueued for sending upon iface removal
- ensure network header pointer is set in skb
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The two commits noted below added calls to ip_hdr() and ipv6_hdr(). They
need a correctly set skb network header.
Unfortunately we cannot rely on the device drivers to set it for us.
Therefore setting it in the beginning of the according ndo_start_xmit
handler.
Fixes: 1d8ab8d3c1 ("batman-adv: Modified forwarding behaviour for multicast packets")
Fixes: ab49886e3d ("batman-adv: Add IPv4 link-local/IPv6-ll-all-nodes multicast support")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
When an interface is purged, the broadcast packets scheduled for this
interface should get purged as well.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The list_del() calls were changed to list_del_init() to prevent
an accidental double deletion in batadv_tt_req_node_new().
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
