The calibration data for devices w/o a separate
EEPROM chip can be specified via the 'eeprom_data'
field of 'ath9k_platform_data'. The 'eeprom_data'
is usually filled from board specific setup
functions. It is easy if the EEPROM data is mapped
to the memory, but it can be complicated if it is
stored elsewhere.
The patch adds support for loading of the EEPROM
data via the firmware API to avoid this limitation.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commits a50915394f and
d7c3b937bd.
This is a revert of a revert of a revert. In addition, it reverts the
even older i915 change to stop using the __GFP_NO_KSWAPD flag due to the
original commits in linux-next.
It turns out that the original patch really was bogus, and that the
original revert was the correct thing to do after all. We thought we
had fixed the problem, and then reverted the revert, but the problem
really is fundamental: waking up kswapd simply isn't the right thing to
do, and direct reclaim sometimes simply _is_ the right thing to do.
When certain allocations fail, we simply should try some direct reclaim,
and if that fails, fail the allocation. That's the right thing to do
for THP allocations, which can easily fail, and the GPU allocations want
to do that too.
So starting kswapd is sometimes simply wrong, and removing the flag that
said "don't start kswapd" was a mistake. Let's hope we never revisit
this mistake again - and certainly not this many times ;)
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use phys_addr_t rather than "void *" for physical memory address.
This removes casts and fixes a "cast from pointer to integer of different
size" warning on ppc44x_defconfig.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Technologic Systems TS-5500 provides digital I/O lines exposed through
pin blocks. On this platform, there are three of them, named DIO1, DIO2
and LCD port, that may be used as a DIO block.
The TS-5500 pin blocks are described in the product's wiki:
http://wiki.embeddedarm.com/wiki/TS-5500#Digital_I.2FO
This driver is not limited to the TS-5500 blocks. It can be extended to
support similar boards pin blocks, such as on the TS-5600.
This patch is the V2 of the previous https://lkml.org/lkml/2012/9/25/671
with corrections suggested by Linus Walleij.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jerome Oufella <jerome.oufella@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Alex writes:
Pretty minor -next pull request. We some additional new bits waiting
internally for release. Hopefully Monday we can get at least some of
them out. The others will probably take a few more weeks.
Highlights of the current request:
- ELD registers for passing audio information to the sound hardware
- Handle GPUVM page faults more gracefully
- Misc fixes
Merge radeon test
* 'drm-next-3.8' of git://people.freedesktop.org/~agd5f/linux: (483 commits)
drm/radeon: bump driver version for new info ioctl requests
drm/radeon: fix eDP clk and lane setup for scaled modes
drm/radeon: add new INFO ioctl requests
drm/radeon/dce32+: use fractional fb dividers for high clocks
drm/radeon: use cached memory when evicting for vram on non agp
drm/radeon: add a CS flag END_OF_FRAME
drm/radeon: stop page faults from hanging the system (v2)
drm/radeon/dce4/5: add registers for ELD handling
drm/radeon/dce3.2: add registers for ELD handling
radeon: fix pll/ctrc mapping on dce2 and dce3 hardware
Linux 3.7-rc7
powerpc/eeh: Do not invalidate PE properly
Revert "drm/i915: enable rc6 on ilk again"
ALSA: hda - Fix build without CONFIG_PM
of/address: sparc: Declare of_iomap as an extern function for sparc again
PM / QoS: fix wrong error-checking condition
bnx2x: remove redundant warning log
vxlan: fix command usage in its doc
8139cp: revert "set ring address before enabling receiver"
MPI: Fix compilation on MIPS with GCC 4.4 and newer
...
Conflicts:
drivers/gpu/drm/exynos/exynos_drm_encoder.c
drivers/gpu/drm/exynos/exynos_drm_fbdev.c
drivers/gpu/drm/nouveau/core/engine/disp/nv50.c
This patch adds support in the kernel for offloading in the NIC Tx and Rx
checksumming for encapsulated packets (such as VXLAN and IP GRE).
For Tx encapsulation offload, the driver will need to set the right bits
in netdev->hw_enc_features. The protocol driver will have to set the
skb->encapsulation bit and populate the inner headers, so the NIC driver will
use those inner headers to calculate the csum in hardware.
For Rx encapsulation offload, the driver will need to set again the
skb->encapsulation flag and the skb->ip_csum to CHECKSUM_UNNECESSARY.
In that case the protocol driver should push the decapsulated packet up
to the stack, again with CHECKSUM_UNNECESSARY. In ether case, the protocol
driver should set the skb->encapsulation flag back to zero. Finally the
protocol driver should have NETIF_F_RXCSUM flag set in its features.
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 2e71a6f808 (net: gro: selective flush of packets) added
a bug for skbs using frag_list. This part of the GRO stack is rarely
used, as it needs skb not using a page fragment for their skb->head.
Most drivers do use a page fragment, but some of them use GFP_KERNEL
allocations for the initial fill of their RX ring buffer.
napi_gro_flush() overwrite skb->prev that was used for these skb to
point to the last skb in frag_list.
Fix this using a separate field in struct napi_gro_cb to point to the
last fragment.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some hosts need to perform additional actions upon card insertion or
ejection. Add a host operation to be called from card detection handlers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
A SMSC PHY in power down mode can't be used.
If a SMSC PHY is in this mode in the config_init
stage, the mode "all capable" is set. So the PHY
could then be used.
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch against kernel 3.7.0-rc8 fixes a kernel oops when turning on the
bluetooth mouse with id 0458:0058 [1].
The mouse in question supports both input and hid sessions, however it is
blacklisted in drivers/hid/hid-core.c so the input session is one that should
be used. Long ago (around kernel 3.0.0) some changes in the bluetooth
subsystem made the kernel do not fallback to input session when hid session is
not supported or blacklisted. This patch restore that behaviour by making the
kernel try the input session if hid_add_device returns ENODEV.
The patch exports hid_ignore() from hid-core.c so that it can be used in the
bluetooth subsystem.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=39882
Signed-off-by: Lamarque V. Souza <lamarque@gmail.com>
Acked-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
6e20a0a429
(gpio: pcf857x: enable gpio_to_irq() support)
added gpio_to_irq() support on pcf857x driver,
but it used pdata->irq.
This patch modifies driver to use client->irq instead of it.
It modifies kzm9g board platform settings,
and device probe information too.
This patch is tested on kzm9g board
Reported-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
codec_fmt and sample_rate variables are unused in both snd_platform_data
and davinci_audio_dev, so drop them.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The common machine driver will be able to support new boards where the voice
port is also in use.
At the same time add possibility to fine tune the connections from twl4030
on the board: jack detection GPIO, input/output selection
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* pci/mjg-pci-roms-from-efi:
x86: Use PCI setup data
PCI: Add support for non-BAR ROMs
PCI: Add pcibios_add_device
EFI: Stash ROMs if they're not in the PCI BAR
Register the watchdog driver to the system if it is a SoC. Using the
watchdog on a non SoC device, like a PCI card, will make the PCI
card die when the timeout expired, but starting it again is not
supported by ssb.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The watchdog driver wants to set the watchdog timeout in ms and not in
ticks, add a method converting ms to ticks before setting the watchdog
register. Return the ticks or millisecond the timer was set to in case
the provided value was bigger than the max allowed value.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prevent the watchdog register on the extif core to be set to a too
high value.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The watchdog driver wants to set the watchdog timeout in ms and not in
ticks, which is depending on the SoC type and the clock.
Calculate the number of ticks per millisecond and provide two functions
for the watchdog driver. Also return the ticks or millisecond the timer
was set to in case the provided value was bigger than the max allowed
value.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Register the watchdog driver to the system if this is a SoC. Using the
watchdog on a non SoC device, like a PCIe card, will make the PCIe
card die when the timeout expired, but starting it again is not
supported by bcma.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The watchdog driver wants to set the watchdog timeout in ms and not in
ticks, which is depending on the SoC type and the clock.
Calculate the number of ticks per millisecond and provide two functions
for the watchdog driver. Also return the ticks or millisecond the timer
was set to in case the provided value was bigger than the max allowed
value.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a common header for watchdog functions, so a watchdog driver
just needs to use this and could provide watchdog functionality for ssb
and bcma based SoCs. Patches for a watchdog driver using this interface
will be send later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a regression in 3.7-rc, which has since gone into stable.
Commit 00442ad04a ("mempolicy: fix a memory corruption by refcount
imbalance in alloc_pages_vma()") changed get_vma_policy() to raise the
refcount on a shmem shared mempolicy; whereas shmem_alloc_page() went
on expecting alloc_page_vma() to drop the refcount it had acquired.
This deserves a rework: but for now fix the leak in shmem_alloc_page().
Hugh: shmem_swapin() did not need a fix, but surely it's clearer to use
the same refcounting there as in shmem_alloc_page(), delete its onstack
mempolicy, and the strange mpol_cond_copy() and __mpol_cond_copy() -
those were invented to let swapin_readahead() make an unknown number of
calls to alloc_pages_vma() with one mempolicy; but since 00442ad04a,
alloc_pages_vma() has kept refcount in balance, so now no problem.
Reported-and-tested-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
