Reset the HDR capabilities during the bridge disable.
The capabilities are re-programmed the next time
the userspace issues the call to populate the modes.
Change-Id: I04dbaa99c291de13b81e12cb9742cc97d9b02593
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Currently, IBB PWRUP_DLY1 and PWRDN_DLY2 settings are configured
only for values greater than 0. However, 0 ms (no delay) can be
allowed by disabling EN_PWRUP_DLY1 or EN_PWRDN_DLY2 bits. Add
support to allow this configuration.
CRs-Fixed: 2125062
Change-Id: I8ef3b5522b8d4db6befb3fb1c2e58ea24c0f5ea0
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
PMI8998 LAB pulse skip configuration is different from PMI8996
and earlier PMICs. Fix it by using the right configuration API
to configure LAB PS_CTL along with supporting PM660A properly.
Since the existing LAB PS configuration threshold for pmi8998 is
incorrect in device tree, update it along with this change.
Change-Id: I2686733867ec3e2909d0c071a5881d3d824c713e
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
If CABC is enabled and auto calibration is attempted, then OVP
fault can be seen even with a valid sink configuration and a
brightness level greater than or equal to 0.4 % dimming. This is
because of the modulation done through CABC pin which if low
enough can cause the brightness level to still go further down.
Fix this by disabling CABC on all sinks before running auto
calibration and re-enable it if the feature is enabled. Also,
modify the auto calibration brightness level to 200 so that the
load increase on WLED_VOUT can bring the voltage below OVP
threshold quick enough on a valid sink configuration.
Finally, disable WLED module before switching the sink
configuration and enable it after configuring sinks.
CRs-Fixed: 2125217
Change-Id: I570dc9eba540cd96328afd7c68f4643a112c4962
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Pass NULL pointer to of_get_address_byname() for size and flags
parameters instead of an integer value 0.
Change-Id: I53984141bb8f1164c27b6a9a5d90853b4d077ee1
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
If the OVP fault is present during boot-up run
a WLED string auto-calibration.
Change-Id: I4b0e85cd64a1e8bca9bc7de17521d1f83798ed12
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
Export msm_ipc.h for use by user-space.
Change-Id: I53b96c4cb0b6fe785d3e73e7f00565c68dadf411
CRs-Fixed: 2125734
Acked-by: Jennifer L Zenner <jzenner@qti.qualcomm.com>
Signed-off-by: Yasir Malik <ymalik@codeaurora.org>
Add configuration for 64-bit FSM platforms.
Change-Id: Icd5fb7875674e537a102af3fbc7d7c8b90c59740
CRs-Fixed: 2125734
Acked-by: Jennifer L Zenner <jzenner@qti.qualcomm.com>
Signed-off-by: Yasir Malik <ymalik@codeaurora.org>
HL1.0 has more number of descriptors and hence we can
queue more packets for tx.
Allow a higher number of tx pending packets for better
throughput in concurrency cases.
CRs-Fixed: 2104072
Change-Id: I8dd98cee04200fbeccf655dcb1d982d037077101
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Clear the deep color bits in the HDMI controller in case
the mode does not need OR support deep color.
Otherwise it causes issues while switching across modes where
the sink supports deep color in one of the modes but not in the
other.
Change-Id: I8accf00e89868ccaa781a3f18eb9a662d9c9235c
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
When multiple worker threads compete to update event_list, with current
vblank_ctrl_worker mechanism, there is one risk which can casue list node
is deleted for twice. This is because, due to the protected scope by
the spin_lock, mutex can exit when one thread is transvering the list,
but another queue thread may continue to add new event to the list.
This brings conflict risk. This patch is to correct this.
Change-Id: Ice31462d196c57ce18d7b998c1a1f0b7feeb08fc
Signed-off-by: Xiaowen Wu <wxiaowen@codeaurora.org>
Signed-off-by: Guchun Chen <guchunc@codeaurora.org>
For NCM gadget function, net device structure opts->net
will be freed when NCM unbind, but user space related
device node doesn't know it, will access net structre
without checking it exist or not, finally lead to crash.
Fix this by adding check gadget function bind or not.
Change-Id: I6af9e3868f71e7fa923600721e1f716508de9b55
Signed-off-by: Liangliang Lu <luliang@codeaurora.org>
When getting string from userspace by simple_write_to_buffer
in ufs_qcom_dbg_testbus_cfg_write() function, the string
copied to configuration is not terminated with '\0'. Thus
stack overflow read may occur while copying configuration to
host->testbus.select_major, which will result in information
leak later while printing error message. This change adds null
character at the end of the input string to avoid information
leak.
Change-Id: Ic9a9204def4bd6976f42f5f80ae5c0a9730afeb1
Signed-off-by: Sayali Lokhande <sayalil@codeaurora.org>
Use system time timestamp for the PPS GPIO driver on
msm8996 CV2X boards.
Change-Id: Ib7231d9b182c956d3c169d6979dbb5fe7f185353
Signed-off-by: Gustavo Solaira <gustavos@codeaurora.org>
If the device tree property "use-system-time-ts" is defined
then the timestamp used for PPS events will be the system time,
otherwise it will be the monotonic boot time.
Change-Id: I92fab1d8861e1d652fcb68066b417f44c1f8e29b
Signed-off-by: Gustavo Solaira <gustavos@codeaurora.org>
Name added for wake source is stored in stack memory. It does
not exist after the stack is gone, this leads to use after free
case.
Added name from Glink xprt struct which persists until
IPCRTR is not removed.
CRs-Fixed: 2124767
Change-Id: I580cf6d6d12682f1f3f25c2506c2b1a969ee89b8
Signed-off-by: Dhoat Harpal <hdhoat@codeaurora.org>
Disable the below defconfigs for SDM660 to address the
VTS KernelConfig test case failures.
Disable:
CONFIG_USELIB
CONFIG_INET_LRO
Enable:
CONFIG_CGROUP_DEBUG
Change-Id: I20ea6e4f7ac2350ad6a57a61a5b42464cfb273ef
Signed-off-by: Srinivas Ramana <sramana@codeaurora.org>
Pop noise occurs during switch from handset to speaker mode
during voice call. This is because sufficient delay
is not provided for tx to unmute. A delayed workqueue
that will do unmute at the end solves the issue.
CRs-Fixed: 2101423
Change-Id: Idc1fd8e770eb0d361bd436ce35940200173106ef
Signed-off-by: Vatsal Bucha <vbucha@codeaurora.org>
Add QBT100 device for SDM630 with necessary clocks and GPIO
configurations. QBT1000 is fingerprint driver to communicate
with fingerprint trustzone app through QSEECOM. It also
receives interrupts from fingerprint sensor.
Change-Id: I0945f6377013f86ad531d9490ccbfa327bca034e
Signed-off-by: Abir Ghosh <abirg@codeaurora.org>
Disable L1/L1ss modes for the RC2 link with MDM9x55 EP on
msm8996 CV2X boards to avoid bursty MSI interrupts and
unstable communication channel.
Change-Id: I12549ec37ceda09ebc9104b0182e53efdcfc8d2f
Signed-off-by: Gustavo Solaira <gustavos@codeaurora.org>
Decouple WLAN host driver suspend/resume and PCI link and MHI
suspend/resume so that PCI link and MHI can be suspended/resumeed
separately without WLAN host driver.
Change-Id: I82cb7b8b54c61657c5d0bbaead0ffc1c55ecee8d
Signed-off-by: Yue Ma <yuem@codeaurora.org>
* refs/heads/tmp-d6fbbe5
Linux 4.4.93
x86/alternatives: Fix alt_max_short macro to really be a max()
USB: serial: console: fix use-after-free after failed setup
USB: serial: qcserial: add Dell DW5818, DW5819
USB: serial: option: add support for TP-Link LTE module
USB: serial: cp210x: add support for ELV TFD500
USB: serial: ftdi_sio: add id for Cypress WICED dev board
fix unbalanced page refcounting in bio_map_user_iov
direct-io: Prevent NULL pointer access in submit_page_section
usb: gadget: composite: Fix use-after-free in usb_composite_overwrite_options
ALSA: line6: Fix leftover URB at error-path during probe
ALSA: caiaq: Fix stray URB at probe error path
ALSA: seq: Fix copy_from_user() call inside lock
ALSA: seq: Fix use-after-free at creating a port
ALSA: usb-audio: Kill stray URB at exiting
iommu/amd: Finish TLB flush in amd_iommu_unmap()
usb: renesas_usbhs: Fix DMAC sequence for receiving zero-length packet
KVM: nVMX: fix guest CR4 loading when emulating L2 to L1 exit
crypto: shash - Fix zero-length shash ahash digest crash
HID: usbhid: fix out-of-bounds bug
dmaengine: edma: Align the memcpy acnt array size with the transfer
MIPS: math-emu: Remove pr_err() calls from fpu_emu()
USB: dummy-hcd: Fix deadlock caused by disconnect detection
rcu: Allow for page faults in NMI handlers
iwlwifi: mvm: use IWL_HCMD_NOCOPY for MCAST_FILTER_CMD
nl80211: Define policy for packet pattern attributes
CIFS: Reconnect expired SMB sessions
ext4: in ext4_seek_{hole,data}, return -ENXIO for negative offsets
brcmfmac: add length check in brcmf_cfg80211_escan_handler()
ANDROID: HACK: arm64: use -mno-implicit-float instead of -mgeneral-regs-only
sched: Update task->on_rq when tasks are moving between runqueues
FROMLIST: f2fs: expose some sectors to user in inline data or dentry case
crypto: Work around deallocated stack frame reference gcc bug on sparc.
UPSTREAM: f2fs: fix potential panic during fstrim
ANDROID: fscrypt: remove unnecessary fscrypto.h
ANDROID: binder: fix node sched policy calculation
ANDROID: Kbuild, LLVMLinux: allow overriding clang target triple
CHROMIUM: arm64: Disable asm-operand-width warning for clang
CHROMIUM: kbuild: clang: Disable the 'duplicate-decl-specifier' warning
UPSTREAM: x86/build: Use cc-option to validate stack alignment parameter
UPSTREAM: x86/build: Fix stack alignment for CLang
UPSTREAM: efi/libstub/arm64: Set -fpie when building the EFI stub
BACKPORT: efi/libstub/arm64: Force 'hidden' visibility for section markers
UPSTREAM: compiler, clang: always inline when CONFIG_OPTIMIZE_INLINING is disabled
UPSTREAM: x86/boot: #undef memcpy() et al in string.c
UPSTREAM: crypto: arm64/sha - avoid non-standard inline asm tricks
UPSTREAM: kbuild: clang: Disable 'address-of-packed-member' warning
UPSTREAM: x86/build: Specify stack alignment for clang
UPSTREAM: x86/build: Use __cc-option for boot code compiler options
BACKPORT: kbuild: Add __cc-option macro
UPSTREAM: x86/hweight: Don't clobber %rdi
BACKPORT: x86/hweight: Get rid of the special calling convention
BACKPORT: x86/mm/kaslr: Use the _ASM_MUL macro for multiplication to work around Clang incompatibility
UPSTREAM: crypto, x86: aesni - fix token pasting for clang
UPSTREAM: x86/kbuild: Use cc-option to enable -falign-{jumps/loops}
UPSTREAM: compiler, clang: properly override 'inline' for clang
UPSTREAM: compiler, clang: suppress warning for unused static inline functions
UPSTREAM: Kbuild: provide a __UNIQUE_ID for clang
UPSTREAM: modules: mark __inittest/__exittest as __maybe_unused
BACKPORT: kbuild: Add support to generate LLVM assembly files
UPSTREAM: kbuild: use -Oz instead of -Os when using clang
BACKPORT: kbuild, LLVMLinux: Add -Werror to cc-option to support clang
UPSTREAM: kbuild: drop -Wno-unknown-warning-option from clang options
UPSTREAM: kbuild: fix asm-offset generation to work with clang
UPSTREAM: kbuild: consolidate redundant sed script ASM offset generation
UPSTREAM: kbuild: Consolidate header generation from ASM offset information
UPSTREAM: kbuild: clang: add -no-integrated-as to KBUILD_[AC]FLAGS
UPSTREAM: kbuild: Add better clang cross build support
Conflicts:
arch/x86/lib/Makefile
net/wireless/nl80211.c
Change-Id: I76032e8d1206903bc948b9ed918e7ddee7e746c7
Signed-off-by: Blagovest Kolenichev <bkolenichev@codeaurora.org>
