This patch disables multicast hash filtering if present in the hardware
and uses promiscuous mode instead until the problem with multicast
filtering has been debugged, integrated and tested.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the many sparse errors and warnings contained in the
initial submission of the Altera Triple Speed Ethernet driver, and a
few minor cppcheck warnings. Changes are tested on ARM and NIOS2
example designs, and compile tested against multiple architectures.
Typical issues addressed were as follows:
altera_tse_ethtool.c:136:19: warning: incorrect type in argument
1 (different address spaces)
altera_tse_ethtool.c:136:19: expected void const volatile
[noderef] <asn:2>*addr
altera_tse_ethtool.c:136:19: got unsigned int *<noident>
...
altera_sgdma.c:129:31: warning: cast removes address space of
expression
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of 06f9cc12ca "nfsd4: don't create
unnecessary mask acl", any non-trivial ACL will be left with an
unitialized entry, and a trivial ACL may write one entry beyond what's
allocated.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
From: Cong Wang <cwang@twopensource.com>
commit 50624c934d (net: Delay default_device_exit_batch until no
devices are unregistering) introduced rtnl_lock_unregistering() for
default_device_exit_batch(). Same race could happen we when rmmod a driver
which calls rtnl_link_unregister() as we call dev->destructor without rtnl
lock.
For long term, I think we should clean up the mess of netdev_run_todo()
and net namespce exit code.
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The attached change significantly improves the performance of the LWS-CAS code
in syscall.S.
This allows a number of packages to build (e.g., zeromq3, gtest and libxs)
that previously failed because slow LWS-CAS performance under contention. In
particular, interrupts taken while the lock was taken degraded performance
significantly.
The change does the following:
1) Disables interrupts around the CAS operation, and
2) Changes the loads and stores to use the ordered completer, "o", on
PA 2.0. "o" and "ma" with a zero offset are equivalent. The latter is
accepted on both PA 1.X and 2.0.
The use of ordered loads and stores probably makes no difference on all
existing hardware, but it seemed pedantically correct. In particular, the CAS
operation must complete before LDCW lock is released. As written before, a
processor could reorder the operations.
I don't believe the period interrupts are disabled is long enough to
significantly increase interrupt latency. For example, the TLB insert code is
longer. Worst case is a memory fault in the CAS operation.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # 3.13+
Signed-off-by: Helge Deller <deller@gmx.de>
Ratelimit printing of userspace segfaults and make it runtime
configurable via the /proc/sys/debug/exception-trace variable. This
should resolve syslog from growing way too fast and thus prevents
possible system service attacks.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 3.13+
When a new device is added below a hotplug bridge, the bridge's secondary
bus speed and the device's bus speed must match. The shpchp driver
previously checked the bridge's *primary* bus speed, not the secondary bus
speed.
This caused hot-add errors like:
shpchp 0000:00:03.0: Speed of bus ff and adapter 0 mismatch
Check the secondary bus speed instead.
[bhelgaas: changelog]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=75251
Fixes: 3749c51ac6 ("PCI: Make current and maximum bus speeds part of the PCI core")
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
CC: stable@vger.kernel.org # v2.6.34+
Change introduced by 88e48d7b33
("batman-adv: make DAT drop ARP requests targeting local clients")
implements a check that prevents DAT from using the caching
mechanism when the client that is supposed to provide a reply
to an arp request is local.
However change brought by be1db4f661
("batman-adv: make the Distributed ARP Table vlan aware")
has not converted the above check into its vlan aware version
thus making it useless when the local client is behind a vlan.
Fix the behaviour by properly specifying the vlan when
checking for a client being local or not.
Reported-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
A pointer to the orig_node representing a bat-gateway is
stored in the gw_node->orig_node member, but the refcount
for such orig_node is never increased.
This leads to memory faults when gw_node->orig_node is accessed
and the originator has already been freed.
Fix this by increasing the refcount on gw_node creation
and decreasing it on gw_node free.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
In the new fragmentation code the batadv_frag_send_packet()
function obtains a reference to the primary_if, but it does
not release it upon return.
This reference imbalance prevents the primary_if (and then
the related netdevice) to be properly released on shut down.
Fix this by releasing the primary_if in batadv_frag_send_packet().
Introduced by ee75ed8887
("batman-adv: Fragment and send skbs larger than mtu")
Cc: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Acked-by: Martin Hundebøll <martin@hundeboll.net>
If hard_iface is NULL and goto out is made batadv_hardif_free_ref()
doesn't check for NULL before dereferencing it to get to refcount.
Introduced in cb1c92ec37
("batman-adv: add debugfs support to view multiif tables").
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Acked-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Add the corresponding trace if we have a full match in a non-terminal
rule. Note that the traces will look slightly different than in
x_tables since the log message after all expressions have been
evaluated (contrary to x_tables, that emits it before the target
action). This manifests in two differences in nf_tables wrt. x_tables:
1) The rule that enables the tracing is included in the trace.
2) If the rule emits some log message, that is shown before the
trace log message.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Make the CONFIG_OF=n prototpe of of_node_full_name() mateh the CONFIG_OF=y
version.
Fixes compile warnings like this:
sound/soc/soc-core.c: In function 'soc_check_aux_dev':
sound/soc/soc-core.c:1667:3: warning: passing argument 1 of 'of_node_full_name' discards 'const' qualifier from pointer target type [enabled by default]
codecname = of_node_full_name(aux_dev->codec_of_node);
when CONFIG_OF is not defined.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
with the right capability number. irqfd for s390x was
introduced with 3.15-rc1, so this fix should still go into
Linus tree for 3.15
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=uARM
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-for-3.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into kvm-master
Here is a fix that aligns the irqfd code changes for 3.15
with the right capability number. irqfd for s390x was
introduced with 3.15-rc1, so this fix should still go into
Linus tree for 3.15
* acpi-video:
ACPI / video: correct DMI tag for Dell Inspiron 7520
ACPI / video: Add use_native_backlight quirks for more systems
* acpi-blacklist:
ACPI / blacklist: Add dmi_enable_osi_linux quirk for Asus EEE PC 1015PX
ACPI: blacklist win8 OSI for Dell Inspiron 7737
* acpi-ac:
ACPI: Revert "ACPI / AC: convert ACPI ac driver to platform bus"
* acpi-proc:
ACPI / proc: Do not say when /proc interfaces will be deleted in Kconfig
ACPI: Revert "ACPI / Battery: Remove battery's proc directory"
ACPI: Revert "ACPI: Remove CONFIG_ACPI_PROCFS_POWER and cm_sbsc.c"
* acpica:
ACPICA: Tables: Restore old behavor to favor 32-bit FADT addresses.
ACPICA: Tables: Fix invalid pointer accesses in acpi_tb_parse_root_table().
* acpi-tpm:
ACPI / TPM: Fix resume regression on Chromebooks
* acpi-processor:
ACPI / processor: do not mark present at boot but not onlined CPU as onlined
On SNB the BIOS provided WM memory latency values seem insufficient to
handle high resolution displays.
In this particular case the display mode was a 2560x1440@60Hz, which
makes the pixel clock 241.5 MHz. It was empirically found that a memory
latency value if 1.2 usec is enough to avoid underruns, whereas the BIOS
provided value of 0.7 usec was clearly too low. Incidentally 1.2 usec
is what the typical BIOS provided values are on IVB systems.
Increase the WM memory latency values to at least 1.2 usec on SNB.
Hopefully this won't have a significant effect on power consumption.
v2: Increase the latency values regardless of the pixel clock
Cc: Robert N <crshman@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=70254
Tested-by: Robert Navarro <crshman@gmail.com>
Tested-by: Vitaly Minko <vitaly.minko@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
s390 has acquired irqfd support with commit "KVM: s390: irq routing for
adapter interrupts" (8422359877) but
failed to announce it. Let's fix that.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
When we set backlight on behalf of ACPI opregion, we will convert the
backlight value in the 0-255 range defined in opregion to the actual
hardware level. Commit 22505b82a2 (drm/i915: avoid brightness overflow
when doing scale) is meant to fix the overflow problem when doing the
conversion, but it also caused a problem that the converted hardware
level doesn't quite represent the intended value: say user wants maximum
backlight level(255 in opregion's range), then we will calculate the
actual hardware level to be: level = freq / max * level, where freq is
the hardware's max backlight level(937 on an user's box), and max and
level are all 255. The converted value should be 937 but the above
calculation will yield 765.
To fix this issue, just use 64 bits to do the calculation to keep the
precision and avoid overflow at the same time.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=72491
Reported-by: Nico Schottelius <nico-bugzilla.kernel.org@schottelius.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This matches the algorithm used by earlier kernels when selecting the
mode for the fbcon. And only if there is no modes at all, do we fall
back to using the BIOS configuration. Seamless transition is still
preserved (from the BIOS configuration to ours) so long as the BIOS has
also chosen what we hope is the native configuration.
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78655
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[Jani: applied Chris' "Please imagine that I wrote this correctly."]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
There are certain BDW high res eDP machines that regressed due to
commit 38aecea0cc
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Mar 3 11:18:10 2014 +0100
drm/i915: reverse dp link param selection, prefer fast over wide again
The commit lead to 2 lanes at 5.4 Gbps being used instead of 4 lanes at
2.7 Gbps on the affected machines. Link training succeeded for both, but
the screen remained blank with the former config. Further investigation
showed that 4 lanes at 5.4 Gbps worked also.
The root cause for the blank screen using 2 lanes remains unknown, but
apparently the driver for a certain other operating system by default
uses the max available lanes. Follow suit on Broadwell eDP, for at least
until we figure out what is going on.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76711
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Tested-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Checkin:
b3b42ac2cb x86-64, modify_ldt: Ban 16-bit segments on 64-bit kernels
disabled 16-bit segments on 64-bit kernels due to an information
leak. However, it does seem that people are genuinely using Wine to
run old 16-bit Windows programs on Linux.
A proper fix for this ("espfix64") is coming in the upcoming merge
window, but as a temporary fix, create a sysctl to allow the
administrator to re-enable support for 16-bit segments.
It adds a "/proc/sys/abi/ldt16" sysctl that defaults to zero (off). If
you hit this issue and care about your old Windows program more than
you care about a kernel stack address information leak, you can do
echo 1 > /proc/sys/abi/ldt16
as root (add it to your startup scripts), and you should be ok.
The sysctl table is only added if you have COMPAT support enabled on
x86-64, but I assume anybody who runs old windows binaries very much
does that ;)
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/CA%2B55aFw9BPoD10U1LfHbOMpHWZkvJTkMcfCs9s3urPr1YyWBxw@mail.gmail.com
Cc: <stable@vger.kernel.org>
_STK_LIM_MAX could be used to override the RLIMIT_STACK hard limit from
an arch's include/uapi/asm-generic/resource.h file, but is no longer
used since both parisc and metag removed the override. Therefore remove
it entirely, setting the hard RLIMIT_STACK limit to RLIM_INFINITY
directly in include/asm-generic/resource.h.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arch@vger.kernel.org
Cc: Helge Deller <deller@gmx.de>
Cc: John David Anglin <dave.anglin@bell.net>
Meta overrode _STK_LIM_MAX (the default RLIMIT_STACK hard limit) to
256MB, apparently in an attempt to prevent setup_arg_pages's
STACK_GROWSUP code from choosing the maximum stack size of 1GB, which is
far too large for Meta's limited virtual address space and hits a BUG_ON
(stack_top is usually 0x3ffff000).
However the commit "metag: Reduce maximum stack size to 256MB" reduces
the absolute stack size limit to a safe value for metag. This allows the
default _STK_LIM_MAX override to be removed, bringing the default
behaviour in line with all other architectures. Parisc in particular
recently removed their override of _STK_LIMT_MAX in commit e0d8898d76
(parisc: remove _STK_LIM_MAX override) since it subtly affects stack
allocation semantics in userland. Meta's uapi/asm/resource.h can now be
removed and switch to using generic-y.
Suggested-by: Helge Deller <deller@gmx.de>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-metag@vger.kernel.org
Cc: John David Anglin <dave.anglin@bell.net>
And we don't invert it properly when initialising the dquot lru
list.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Jie Liu <jeff.liu@oracle.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Invert it.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Jie Liu <jeff.liu@oracle.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
And it should be negative.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Jie Liu <jeff.liu@oracle.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
This patch affects only architectures where the stack grows upwards
(currently parisc and metag only). On those do not hardcode the maximum
initial stack size to 1GB for 32-bit processes, but make it configurable
via a config option.
The main problem with the hardcoded stack size is, that we have two
memory regions which grow upwards: stack and heap. To keep most of the
memory available for heap in a flexmap memory layout, it makes no sense
to hard allocate up to 1GB of the memory for stack which can't be used
as heap then.
This patch makes the stack size for 32-bit processes configurable and
uses 80MB as default value which has been in use during the last few
years on parisc and which hasn't showed any problems yet.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: linux-parisc@vger.kernel.org
Cc: linux-metag@vger.kernel.org
Cc: John David Anglin <dave.anglin@bell.net>
Specify the maximum stack size for arches where the stack grows upward
(parisc and metag) in asm/processor.h rather than hard coding in
fs/exec.c so that metag can specify a smaller value of 256MB rather than
1GB.
This fixes a BUG on metag if the RLIMIT_STACK hard limit is increased
beyond a safe value by root. E.g. when starting a process after running
"ulimit -H -s unlimited" it will then attempt to use a stack size of the
maximum 1GB which is far too big for metag's limited user virtual
address space (stack_top is usually 0x3ffff000):
BUG: failure at fs/exec.c:589/shift_arg_pages()!
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: linux-parisc@vger.kernel.org
Cc: linux-metag@vger.kernel.org
Cc: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # only needed for >= v3.9 (arch/metag)
Volatile access doesn't really imply the compiler barrier. Volatile access
is only ordered with respect to other volatile accesses, it isn't ordered
with respect to general memory accesses. Gcc may reorder memory accesses
around volatile access, as we can see in this simple example (if we
compile it with optimization, both increments of *b will be collapsed to
just one):
void fn(volatile int *a, long *b)
{
(*b)++;
*a = 10;
(*b)++;
}
Consequently, we need the compiler barrier after a write to the volatile
variable, to make sure that the compiler doesn't reorder the volatile
write with something else.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Commit 3e9f1be1b4 ("dm mpath: remove process_queued_ios()") did not
consistently take the multipath device's spinlock (m->lock) before
calling dm_table_run_md_queue_async() -- which takes the q->queue_lock.
Found with code inspection using hint from reported lockdep warning.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If the pool runs out of data space, dm-thin can be configured to
either error IOs that would trigger provisioning, or hold those IOs
until the pool is resized. Unfortunately, holding IOs until the pool is
resized can result in a cascade of tasks hitting the hung_task_timeout,
which may render the system unavailable.
Add a fixed timeout so IOs can only be held for a maximum of 60 seconds.
If LVM is going to resize a thin-pool that is out of data space it needs
to be prompt about it.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.14+
Commit 3e1a0699 ("dm thin: fix out of data space handling") introduced
a regression in the metadata commit() method by returning an error if
the pool is in PM_OUT_OF_DATA_SPACE mode. This oversight caused a thin
device to return errors even if the default queue_if_no_space ENOSPC
handling mode is used.
Fix commit() to only fail if pool is in PM_READ_ONLY or PM_FAIL mode.
Reported-by: qindehua@163.com
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.14+
The DM crypt target used per-cpu structures to hold pointers to a
ablkcipher_request structure. The code assumed that the work item keeps
executing on a single CPU, so it didn't use synchronization when
accessing this structure.
If a CPU is disabled by writing 0 to /sys/devices/system/cpu/cpu*/online,
the work item could be moved to another CPU. This causes dm-crypt
crashes, like the following, because the code starts using an incorrect
ablkcipher_request:
smpboot: CPU 7 is now offline
BUG: unable to handle kernel NULL pointer dereference at 0000000000000130
IP: [<ffffffffa1862b3d>] crypt_convert+0x12d/0x3c0 [dm_crypt]
...
Call Trace:
[<ffffffffa1864415>] ? kcryptd_crypt+0x305/0x470 [dm_crypt]
[<ffffffff81062060>] ? finish_task_switch+0x40/0xc0
[<ffffffff81052a28>] ? process_one_work+0x168/0x470
[<ffffffff8105366b>] ? worker_thread+0x10b/0x390
[<ffffffff81053560>] ? manage_workers.isra.26+0x290/0x290
[<ffffffff81058d9f>] ? kthread+0xaf/0xc0
[<ffffffff81058cf0>] ? kthread_create_on_node+0x120/0x120
[<ffffffff813464ac>] ? ret_from_fork+0x7c/0xb0
[<ffffffff81058cf0>] ? kthread_create_on_node+0x120/0x120
Fix this bug by removing the per-cpu definition. The structure
ablkcipher_request is accessed via a pointer from convert_context.
Consequently, if the work item is rescheduled to a different CPU, the
thread still uses the same ablkcipher_request.
This change may undermine performance improvements intended by commit
c0297721 ("dm crypt: scale to multiple cpus") on select hardware. In
practice no performance difference was observed on recent hardware. But
regardless, correctness is more important than performance.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
This is the s390 variant of Alexei's JIT bug fix.
(patch description below stolen from Alexei's patch)
bpf_alloc_binary() adds 128 bytes of room to JITed program image
and rounds it up to the nearest page size. If image size is close
to page size (like 4000), it is rounded to two pages:
round_up(4000 + 4 + 128) == 8192
then 'hole' is computed as 8192 - (4000 + 4) = 4188
If prandom_u32() % hole selects a number >= PAGE_SIZE - sizeof(*header)
then kernel will crash during bpf_jit_free():
kernel BUG at arch/x86/mm/pageattr.c:887!
Call Trace:
[<ffffffff81037285>] change_page_attr_set_clr+0x135/0x460
[<ffffffff81694cc0>] ? _raw_spin_unlock_irq+0x30/0x50
[<ffffffff810378ff>] set_memory_rw+0x2f/0x40
[<ffffffffa01a0d8d>] bpf_jit_free_deferred+0x2d/0x60
[<ffffffff8106bf98>] process_one_work+0x1d8/0x6a0
[<ffffffff8106bf38>] ? process_one_work+0x178/0x6a0
[<ffffffff8106c90c>] worker_thread+0x11c/0x370
since bpf_jit_free() does:
unsigned long addr = (unsigned long)fp->bpf_func & PAGE_MASK;
struct bpf_binary_header *header = (void *)addr;
to compute start address of 'bpf_binary_header'
and header->pages will pass junk to:
set_memory_rw(addr, header->pages);
Fix it by making sure that &header->image[prandom_u32() % hole] and &header
are in the same page.
Fixes: aa2d2c73c2 ("s390/bpf,jit: address randomize and write protect jit code")
Reported-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: <stable@vger.kernel.org> # v3.11+
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During remain on channel request, ANI worker thread is not stopped
before doing hw reset. This is causing kernel crash in
hw_per_calibration. This change ensures that ANI is stopped before
doing chip reset and it will be rescheduled later when the chip is
configured back to home channel and having valid bss.
Reported-by: David Herrmann <dh.herrmann@gmail.com>
Tested-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sending data through IUCV a MESSAGE COMPLETE interrupt
signals that sent data memory can be freed or reused again.
With commit f9c41a62bb
"af_iucv: fix recvmsg by replacing skb_pull() function" the
MESSAGE COMPLETE callback iucv_callback_txdone() identifies
the wrong skb as being confirmed, which leads to data corruption.
This patch fixes the skb mapping logic in iucv_callback_txdone().
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some BE3 FW versions, after a HW reset, interrupts will remain disabled
for each function. So, explicitly enable the interrupts in the eeh_resume
handler, else after an eeh recovery interrupts wouldn't work.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
G2D power domain also controls the CMU block of G2D. Since
clock registers can be accessed anytime for viewing
clk_summary, it can cause a system crash if g2d power domain
is disabled.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
MAU powerdomain provides clocks for Audio sub-system block.
This block comprises of the I2S audio controller, audio DMA
blocks and Audio sub-system clock registers.
Right now, there is no way to hook up power-domains with
clock providers. During late boot when this power-domain
gets disabled, we get following external abort.
Unhandled fault: imprecise external abort (0x1406) at 0x00000000
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000007
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
