Composition switch to GSI transport based composition from
another GSI transport based composition requires power on
reset of USB controller to synchronize operation with USB
wrapper for GSI. Specifically GSI_EN bit cannot be
cleared without performing usb controller reset. Hence
introduce gadget restart operation to simulate vbus off
and vbus on and perform this operation from gsi bind
config.
Change-Id: Ie4695807c73c2d14c0d9e17c486f34a90fd93ddb
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Optimize the dwc3_gadget_resize_tx_fifos() function to better
allocate the per-endpoint FIFOs depending on a number of factors:
- super- or non-super speed
- bulk/isoc with bursting
- reduced RAM (when QDSS uses some internal RAM)
- endpoint enabled in composition
Signed-off-by: Jack Pham <jackp@codeaurora.org>
This member is used to store additional private flags
for BAM-enabled functions to pass information to the UDC.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
This change adds support for sourcing and pulsig with DP/DM
using QUSB PHY. This change uses POWER_SUPPLY_PROP_DP_DM power
supply property with different values to achieve the same.
This change is a cherry-pick of msm-3.18 commit
55b93e2506d5399b1b0ee4a1b173168fb8026548 ("USB: Add support to
invoke DP and DM sourcing and pulsing") with only the change
from include/linux/usb/phy.h
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
This state is used to handle:-
- Bus suspend followed by cable disconnect: pm usage
count is incremented upon cable connect. Upon bus
suspend, suspend interrupt kicks in otg state machine
which moves device state to OTG_STATE_B_SUSPENDED from
OTG_STATE_B_PERIPHERAL and decrements pm usage count.
Upon cable unplug additional decrement of pm usage count
is prevented. This state also takes care the handling of
cable unplug followed by bus suspend interrupt.
- Host initiated resume after bus suspend: Being in
OTG_STATE_B_SUSPENDED after bus suspend, upon host
initiated resume, wakeup interrupt kicks in otg state machine
which moves device to OTG_STATE_B_PERIPHERAL state by
incrementing pm usage count.
- PC reboot with cable plugged in: After PC shutdown
device goes to OTG_STATE_B_SUSPENDED state. After
PC start power event irq thread kicks in otg state
machine to move device to OTG_STATE_B_PERIPHERAL
state and increments pm usage count.
- Composition switch after bus suspend:
dwc3_gadget_pullup() kicks in otg state machine to
move device state from OTG_STATE_B_SUSPENDED to
OTG_STATE_B_PERIPHERAL and increments pm usage count
to prevent runtime suspend during device enumeration.
Also, remove pm_runtime_set_active() which sets the PM
runtime stauts as active to avoid pm_runtime_get_sync() failures
which explicitly checks for runtime pm status. For example, if
status is active, pm_runtime_get_sync() will just increments the
counter without actually resuming the device.
Change-Id: Id33b81911ef3894a00802b3e553840b9447f6269
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
[jackp@codeaurora.org: cherry-pick only phy.h and common.c]
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Add a new PHY callback for performing PHY reset, which is required
by some targets during their initialization sequence.
As usb_phy_reset name was already in use by local msm PHY APIs,
change the previous usb_phy_reset to msm_usb_phy_reset.
Change-Id: Ieb5099d12e107c123d8889058aa564d0b091d6f9
Signed-off-by: Maya Erez <merez@codeaurora.org>
Add dwc3-msm.c and associated driver files. Note these are
based on the downstream implementation and will coexist
(for the time being) with dwc3-qcom glue driver until they
can eventually be merged.
This snapshot is taken as of msm-3.18 commit a3883c356869 (Merge "input:
touchscreen: correct condition checks in ITE tech touch driver")
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Implement support for allocating an EP based on name.
This allows a function driver to request an EP using an
ep name string. This is useful to request GSI specific
EPs.
CRs-Fixed: 946385
Change-Id: Id38e6e1e3c2d82f440c0507d24f18f808dc3e4dc
Signed-off-by: Devdutt Patnaik <dpatnaik@codeaurora.org>
Register gsi function suspend callback with composite device to
handle super speed function suspend and resume. Also, move
function suspend option masks to composite device layer.
Change-Id: Ie316973d855612ddc5440934344d18b04d49c567
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Targets supporting h/w accelerated path over GSI require
GSI specific configuration of USB controller.
Add support to enable h/w accelerated path to IPA.
Include operations to configure USB endpoints as
GSI capable, allocate TRBs that are associated with
GSI capable endpoints, perform operations on these
endpoints, and enable the GSI wrapper in DWC3 controller.
This allows a function driver to use GSI based h/w
accelerated data path.
Change-Id: I62688c70a04b1fdab3e522e0af759ebab69d92d7
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
This change adds APIs to allocate and instanciate
multi instance diag function driver using configFS.
Add an entry in kconfig to select diag driver for
configFS.
Change-Id: I428631dc63643eddb075a09d0e46e1a6b1117f0e
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Add function driver to support Qualcomm diagnostics port over USB.
This snapshot is taken as of msm-3.18 commit:
commit e70ad0cd5e (Promotion of kernel.lnx.3.18-151201)
Change-Id: I51aaa8f6a2e05fc252ea810244ddfc99ca2741cc
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
This variable keeps track of when remote_wakeup feature
has been enabled by the host. It is needed for certain
function drivers to perform alternate methods during
suspend/resume.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link Power Management (a.k.a. L1) is similar to the existing usb bus
suspend/resume/remote-wakeup, but has transitional latencies of tens
of microseconds between power states (instead of three to greater than
20 millisecond latencies of the USB 2.0 suspend/resume).
Change-Id: I8ae493534702e658c24f384a6b705b08e9ea9d05
Signed-off-by: Shimrit Malichi <smalichi@codeaurora.org>
Signed-off-by: Tarun Gupta <tarung@codeaurora.org>
In super speed mode if userspace issues a write after usb bus suspend
usb_func_ep_queue() schedules wakeup to resume the function. After that
it queues the request which fails with -ENOTSUPP. As a result no
notification request queued to hw and write request gets delayed to be
sent until another write request comes and queues notification request
after function resume. This causes mismatch to the mbim request response.
Fix this by queuing the notification request upon function resume if
notify count is greater than zero. Also, drop control packet after bus
suspend if remote wakeup is not supported or if ep enqueue returns error
other than -EAGAIN.
CRs-Fixed: 789467
Change-Id: I446de1eb169b4ccb8f4db5f003b622d7b9c0b22b
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Azhar Shaikh <azhars@codeaurora.org>
In Super-Speed mode, when the USB core wishes to issue remote wakeup due to
new data arriving on the BAM to BAM path, it needs to send Function Wakeup
notification to the USB host after the USB bus is resumed. However, the
sending of this notification fails when the USB core needs to wake up from
low-power mode, because the low-power mode exit is done asynchronously and
the sending of the Function Wakeup notification can not be done until the
USB bus is resumed.
This patch fixes this issue by checking whether the USB bus is suspended,
and if so, the sending Function Wakeup notification is delayed until the
USB bus is resumed.
Change-Id: I293476aaaf920b67fdbdf72a63524edc7a35750b
Signed-off-by: Danny Segal <dsegal@codeaurora.org>
The USB 3.0 specification defines a new 'Function Suspend' feature.
This feature enables the USB host to put inactive composite device
functions in a suspended state even when the device itself is not
suspended. This patch extends the existing framework of USB gadget
to properly support the 'Function Resume' and 'Function Remote Wakeup'
related features.
Change-Id: I51713eac557eabc7b465d161377c09d4b6afa152
Signed-off-by: Danny Segal <dsegal@codeaurora.org>
This CL adds a new class to monitor and change
dual role usb ports from userspace. The usb
phy drivers can register to the dual_role_usb
class and expose the capabilities of the ports.
The phy drivers can decide on whether a specific
attribute can be changed from userspace by
choosing to implement the appropriate callback.
Cherry-picked from
https://android-review.googlesource.com/#/c/167310/
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Bug: 21615151
Change-Id: Id1c4aaa97e898264d7006381a7badd029b5d9789
Add a pointer to the usb_function inside the
usb_function_instance structure to service
functions specific setup requests even before
the function gets added to the usb_gadget
Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com>
Change-Id: I6f457006f6c5516cc6986ec2acdf5b1ecf259d0c
Move the entire contents of linux/usb/f_accessory.h header to uapi,
it only contains a userspace interface.
Change-Id: Ieb5547da449588ae554988a201c0e6b4e3afc531
Signed-off-by: Colin Cross <ccross@android.com>
Move the most of linux/usb/f_mtp.h header to uapi. Move the only
remaining structure definition into f_mtp.c, the only place that
uses it.
Change-Id: I952c1a9dc15c36bf295a0eb4d74b6b1ad912ed03
Signed-off-by: Colin Cross <ccross@android.com>
The control request will be used by the host to enable/disable USB audio
and the ioctl will be used by userspace to read the audio mode
Change-Id: I81c38611b588451e80eacdccc417ca6e11c60cab
Signed-off-by: Mike Lockwood <lockwood@google.com>
USB accessory mode allows users to connect USB host hardware
specifically designed for Android-powered devices. The accessories
must adhere to the Android accessory protocol outlined in the
http://accessories.android.com documentation. This allows
Android devices that cannot act as a USB host to still interact with
USB hardware. When an Android device is in USB accessory mode, the
attached Android USB accessory acts as the host, provides power
to the USB bus, and enumerates connected devices.
Change-Id: I67964b50d278f3c0471d47efbb7b0973a3502681
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB gadget function driver used by the Android framework to
implement the MTP and PTP protocols. It creates a character device
that provides an interface for fast transfer of files and
supports transferring files greater than 4GB.
Change-Id: I2d8f2c37029fb37d8deb791d04eb7346f94f5adb
Signed-off-by: Mike Lockwood <lockwood@android.com>
NCM buffer sizes are negotiated with the device independently of
the network device MTU. The RX buffers are allocated by the
usbnet framework based on the rx_urb_size value set by cdc_ncm. A
single RX buffer can hold a number of MTU sized packets.
The default usbnet change_mtu ndo only modifies rx_urb_size if it
is equal to hard_mtu. And the cdc_ncm driver will set rx_urb_size
and hard_mtu independently of each other, based on dwNtbInMaxSize
and dwNtbOutMaxSize respectively. It was therefore assumed that
usbnet_change_mtu() would never touch rx_urb_size. This failed to
consider the case where dwNtbInMaxSize and dwNtbOutMaxSize happens
to be equal.
Fix by implementing an NCM specific change_mtu ndo, modifying the
netdev MTU without touching the buffer size settings.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some USB device / host controller combinations seem to have problems
with Link Power Management. For example, Steinar found that his xHCI
controller wouldn't handle bandwidth calculations correctly for two
video cards simultaneously when LPM was enabled, even though the bus
had plenty of bandwidth available.
This patch introduces a new quirk flag for devices that should remain
disabled for LPM, and creates quirk entries for Steinar's devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull SCSI target updates from Nicholas Bellinger:
"This series contains HCH's changes to absorb configfs attribute
->show() + ->store() function pointer usage from it's original
tree-wide consumers, into common configfs code.
It includes usb-gadget, target w/ drivers, netconsole and ocfs2
changes to realize the improved simplicity, that now renders the
original include/target/configfs_macros.h CPP magic for fabric drivers
and others, unnecessary and obsolete.
And with common code in place, new configfs attributes can be added
easier than ever before.
Note, there are further improvements in-flight from other folks for
v4.5 code in configfs land, plus number of target fixes for post -rc1
code"
In the meantime, a new user of the now-removed old configfs API came in
through the char/misc tree in commit 7bd1d4093c ("stm class: Introduce
an abstraction for System Trace Module devices").
This merge resolution comes from Alexander Shishkin, who updated his stm
class tracing abstraction to account for the removal of the old
show_attribute and store_attribute methods in commit 517982229f
("configfs: remove old API") from this pull. As Alexander says about
that patch:
"There's no need to keep an extra wrapper structure per item and the
awkward show_attribute/store_attribute item ops are no longer needed.
This patch converts policy code to the new api, all the while making
the code quite a bit smaller and easier on the eyes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>"
That patch was folded into the merge so that the tree should be fully
bisectable.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (23 commits)
configfs: remove old API
ocfs2/cluster: use per-attribute show and store methods
ocfs2/cluster: move locking into attribute store methods
netconsole: use per-attribute show and store methods
target: use per-attribute show and store methods
spear13xx_pcie_gadget: use per-attribute show and store methods
dlm: use per-attribute show and store methods
usb-gadget/f_serial: use per-attribute show and store methods
usb-gadget/f_phonet: use per-attribute show and store methods
usb-gadget/f_obex: use per-attribute show and store methods
usb-gadget/f_uac2: use per-attribute show and store methods
usb-gadget/f_uac1: use per-attribute show and store methods
usb-gadget/f_mass_storage: use per-attribute show and store methods
usb-gadget/f_sourcesink: use per-attribute show and store methods
usb-gadget/f_printer: use per-attribute show and store methods
usb-gadget/f_midi: use per-attribute show and store methods
usb-gadget/f_loopback: use per-attribute show and store methods
usb-gadget/ether: use per-attribute show and store methods
usb-gadget/f_acm: use per-attribute show and store methods
usb-gadget/f_hid: use per-attribute show and store methods
...
Here is the big USB patchset for 4.4-rc1.
As usual, most of the changes are in the gadget subsystem, and we
removed a host controller for a device that is no longer in existance,
and probably never was even made public. There is also other minor
driver updates and new device ids, full details in the changelog.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlY6gVMACgkQMUfUDdst+ynLZgCePfhiDuwriaX7osq90HDu8JOc
pTEAn2dBdw2VMPToUlxccR963YSfgu2A
=mMgp
-----END PGP SIGNATURE-----
Merge tag 'usb-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB patchset for 4.4-rc1.
As usual, most of the changes are in the gadget subsystem, and we
removed a host controller for a device that is no longer in existance,
and probably never was even made public. There is also other minor
driver updates and new device ids, full details in the changelog.
All of these have been in linux-next for a while"
* tag 'usb-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (233 commits)
USB: core: Codestyle fix in urb.c
usb: misc: usb3503: Use i2c_add_driver helper macro
usb: host: lpc32xx: don't unregister phy device
usb: host: lpc32xx: balance clk enable/disable on removal
usb: host: lpc32xx: fix warnings caused by enabling unprepared clock
uwb: drp: Use setup_timer
uwb: neh: Use setup_timer
uwb: rsv: Use setup_timer
USB: qcserial: add Sierra Wireless MC74xx/EM74xx
usb: chipidea: otg: don't wait vbus drops below BSV when starts host
chipidea: ci_hdrc_pci: use PCI_VDEVICE() instead of PCI_DEVICE()
doc: dt-binding: ci-hdrc-usb2: split vendor specific properties
usb: chipidea: imx: add imx6ul usb support
doc: dt-binding: ci-hdrc-usb2: improve property description
usb: chipidea: imx: add usb support for imx7d
Doc: usb: ci-hdrc-usb2: Add phy-clkgate-delay-us entry
usb: chipidea: Add support for 'phy-clkgate-delay-us' property
usb: chipidea: Use extcon framework for VBUS and ID detect
usb: gadget: net2280: restore ep_cfg after defect7374 workaround
usb: dwc2: host: Fix use after free w/ simultaneous irqs
...
- Use extcon framework for VBUS and ID detect
- Add imx6sx and imx7d support
- Other small changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWKEKdAAoJEEhZKYFQ1nG7dysH/jmFSatDJvgA7woliRZ7p0H/
elNu6AOjqBnsi23Vp54IOVWYTVIDhLsXxlzEOgO6XXfsI99TqFQIIS2VYSo6xues
Eq5hIxh5n9uue3VMnw9bxYHcFkFG9LDAlyMXecEayAB74UqnQLbo2bRDfnSopaf1
dEOq9mdT8llYbtVww6bVXtL78wgwxVk1gTfISllxgt7DEuYwgT+gQJCDLrmkGPn0
XfiaZWamNmDlQd4z/qqoG65+yNmZZMZQKtugCx4MoiBbHVclRN7j2eNsCZ0y6dsZ
qxs+CazL/IeYCqxRRXl5Fopraer1uJeOPeFgA+lRV6WPhMEe7eg6ojkDp/8Y18Y=
=Dh+g
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
USB Chipidea updates for v4.4-rc1
- Use extcon framework for VBUS and ID detect
- Add imx6sx and imx7d support
- Other small changes
This pull request is large with a total of 136 non-merge
commits. Because of its size, we will only describe the big things in
broad terms.
Many will be happy to know that dwc3 is now almost twice as fast after
some profiling and speed improvements. Also in dwc3, John Youn from
Synopsys added support for their new DWC USB3.1 IP Core and the HAPS
platform which can be used to validate it.
A series of patches from Robert Baldyga cleaned up uses of
ep->driver_data as a flag for "claimed endpoint" in favor of the new
ep->claimed flag.
Sudip Mukherjee fixed a ton of really old problems on the amd5536udc
driver. That should make a few people happy.
Heikki Krogerus worked on converting dwc3 to the unified device property
interface.
Together with these, there's a ton of non-critical fixes, typos and
stuff like that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jPoY
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.4 merge window
This pull request is large with a total of 136 non-merge
commits. Because of its size, we will only describe the big things in
broad terms.
Many will be happy to know that dwc3 is now almost twice as fast after
some profiling and speed improvements. Also in dwc3, John Youn from
Synopsys added support for their new DWC USB3.1 IP Core and the HAPS
platform which can be used to validate it.
A series of patches from Robert Baldyga cleaned up uses of
ep->driver_data as a flag for "claimed endpoint" in favor of the new
ep->claimed flag.
Sudip Mukherjee fixed a ton of really old problems on the amd5536udc
driver. That should make a few people happy.
Heikki Krogerus worked on converting dwc3 to the unified device property
interface.
Together with these, there's a ton of non-critical fixes, typos and
stuff like that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for the optional 'phy-clkgate-delay-us' property that is
used to describe the delay time between putting PHY into low power mode
and turning off the PHY clock.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
On recent Qualcomm platforms VBUS and ID lines are not routed to
USB PHY LINK controller. Use extcon framework to receive connect
and disconnect ID and VBUS notification.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes the following warning if 64-bit architecture environment:
./drivers/usb/renesas_usbhs/common.c:496:25: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
dparam->type = of_id ? (u32)of_id->data : 0;
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hosts that support USB 3.1 Enhaned SuperSpeed can set their speed to
HCD_USB31 to let usb core and host drivers know that the controller
supports new USB 3.1 features.
make sure usb core handle HCD_USB31 hosts correctly, for now similar
to HCD_USB3.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following warning if 64-bit architecture environment:
./drivers/usb/renesas_usbhs/common.c:496:25: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
dparam->type = of_id ? (u32)of_id->data : 0;
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
- Replace all "transceiver" with "phy"
- Replace one "OTG controller" with "phy"
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch introduces 'enabled' flag in struct usb_ep, and modifies
usb_ep_enable() and usb_ep_disable() functions to encapsulate endpoint
enabled/disabled state. It helps to avoid enabling endpoints which are
already enabled, and disabling endpoints which are already disables.
From now USB functions don't have to remember current endpoint
enable/disable state, as this state is now handled automatically which
makes this API less bug-prone.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch introduces usb_ep_autoconfig_release() function which allows
to release endpoint previously obtained from usb_ep_autoconfig() during
USB function bind.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Set the Power register HSENAB bit based on musb->config->maximum_speed,
so that the glue layer can control MUSB to work in high- or full-speed.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
With this patch a flag instead of a variable
is used for the default device authorization.
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interfaces are allowed per default.
This can disabled or enabled (again) by writing 0 or 1 to
/sys/bus/usb/devices/usbX/interface_authorized_default
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In file included from drivers/usb/gadget/function/u_serial.h:16:0,
from drivers/usb/gadget/function/f_acm.c:23:
>> include/linux/usb/cdc.h:47:5: warning: 'struct usb_interface' declared inside parameter list
int buflen);
^
>> include/linux/usb/cdc.h:47:5: warning: its scope is only this definition or declaration, which is probably not what you want
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CDC drivers all implement their own parser for the extra headers.
This patch fixes the code duplication introducing a single common
parser in usbnet.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 1d958bef45 as the
signed-off-by address is invalid.
Cc: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
