Remove unused function ext4_ext_check_cache() and merge the code back to
the ext4_ext_in_cache().
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Similar situation to that of __alloc_fd(); do not use unless you
really have to. You should not touch any descriptor table other
than your own; it's a sure sign of a really bad API design.
As with __alloc_fd(), you *must* use a first-class reference to
struct files_struct; something obtained by get_files_struct(some task)
(let alone direct task->files) will not do. It must be either
current->files, or obtained by get_files_struct(current) by the
owner of that sucker and given to you.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
At that point nobody can see us anyway; everything that
looks at files_fdtable(files) is separated from the
guts of put_files_struct(files) - either since files is
current->files or because we fetched it under task_lock()
and hadn't dropped that yet, or because we'd bumped
files->count while holding task_lock()...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Essentially, alloc_fd() in a files_struct we own a reference to.
Most of the time wanting to use it is a sign of lousy API
design (such as android/binder). It's *not* a general-purpose
interface; better that than open-coding its guts, but again,
playing with other process' descriptor table is a sign of bad
design.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
... except for one in android, where the check is different
and already done in caller. No need to recalculate rlimit
many times in alloc_fd() either.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* do copy_to_user() before prepare_for_access_response(); that kills
the need in remove_access_response().
* don't do fd_install() until we are past the last possible failure
exit. Don't use sys_close() on cleanup side - just put_unused_fd()
and fput(). Less racy that way...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
don't mess with sys_close() if copy_to_user() fails; just postpone
fd_install() until we know it hasn't.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The only difference between autofs_dev_ioctl_fd_install() and
fd_install() is __set_close_on_exec() done by the latter. Just
use get_unused_fd_flags(O_CLOEXEC) to allocate the descriptor
and be done with that...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Using kmem_cache_zalloc() instead of kmem_cache_alloc() and memset().
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
As inode64 is the default option now, and was also made remountable
previously, inode32 can also be remounted on-the-fly when it is needed.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
To make inode32 a remountable option, xfs_set_inode32() should be able
to make a transition from inode64 option, disabling inode allocation on
higher AGs.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
With the changes made on xfs_set_inode64(), to make it behave as
xfs_set_inode32() (now leaving to the caller the responsibility to update
mp->m_maxagi), we use the return value of xfs_set_inode64() to update
mp->m_maxagi during remount.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Add xfs_set_inode32() to be used to enable inode32 allocation mode. this
will reduce the amount of duplicated code needed to mount/remount a
filesystem with inode32 option. This patch also changes
xfs_set_inode64() to return the maximum AG number that inodes can be
allocated instead of set mp->m_maxagi by itself, so that the behaviour
is the same as xfs_set_inode32(). This simplifies code that calls these
functions and needs to know the maximum AG that inodes can be allocated
in.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
since 64-bit inodes can be accessed while using inode32, and these can
also be used on 32-bit kernels, there is no reason to still keep inode32
as the default mount option. If the filesystem cannot handle 64bit
inode numbers (i.e CONFIG_LBDAF is not enabled and BITS_PER_LONG == 32),
XFS_MOUNT_SMALL_INUMS will still be set by default, so inode64 is not an
unconditional default value.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
xfs_ialloc_next_ag() currently resets m_agirotor when it is equal to
m_maxagi:
if (++mp->m_agirotor == mp->m_maxagi)
mp->m_agirotor = 0;
But, if for some reason mp->m_maxagi changes to a lower value than
current m_agirotor, this condition will never be true, causing
m_agirotor to exceed the maximum allowed value (m_maxagi).
This implies mainly during lookups for xfs_perag structs in its radix
tree, since the agno value used for the lookup is based on m_agirotor.
An out-of-range m_agirotor may cause a lookup failure which in case will
return NULL.
As an example, the value of m_maxagi is decreased during
inode64->inode32 remount process, case where I've found this problem.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Actually, there is no reason about why a user must umount and mount a
XFS filesystem to enable 'inode64' option. So, this patch makes this a
remountable option.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
ERRnoresource is an ERRSRV level (aka server-side) error and means "No
resources currently available for request". Currently that maps to POSIX
-ENOBUFS. No NT errors map to it currently.
NT_STATUS_INSUFFICIENT_RESOURCES and NT_STATUS_INSUFF_SERVER_RESOURCES
are also similar in meaning. Currently the client maps those to
ERRnomem, which maps to -ENOMEM in POSIX.
All of these mappings seem to be quite wrong to me and are confusing for
users. All of the above errors indicate problems on the server, not the
client. Reporting -ENOMEM or -ENOBUFS implies that the client is running
out of resources.
This patch changes those mappings. The NT_* errors are changed to map to
the SRV level ERRnoresource. That error is in turn changed to return
-EREMOTEIO which is the only POSIX error I could find that conveys that
something went wrong on the server. While we're at it, change the SMB2
equivalent error to return the same.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Acked-by: Suresh Jayaraman <sjayaraman@suse.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Uninitialized extent may became initialized(parallel writeback task)
at any moment after we drop i_data_sem, so we have to recheck extent's
state after we hold page's lock and i_data_sem.
If we about to change page's mapping we must hold page's lock in order to
serialize other users.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Non-full list of bugs:
1) uninitialized extent optimization does not hold page's lock,
and simply replace brunches after that writeback code goes
crazy because block mapping changed under it's feets
kernel BUG at fs/ext4/inode.c:1434! ( 288'th xfstress)
2) uninitialized extent may became initialized right after we
drop i_data_sem, so extent state must be rechecked
3) Locked pages goes uptodate via following sequence:
->readpage(page); lock_page(page); use_that_page(page)
But after readpage() one may invalidate it because it is
uptodate and unlocked (reclaimer does that)
As result kernel bug at include/linux/buffer_head.c:133!
4) We call write_begin() with already opened stansaction which
result in following deadlock:
->move_extent_per_page()
->ext4_journal_start()-> hold journal transaction
->write_begin()
->ext4_da_write_begin()
->ext4_nonda_switch()
->writeback_inodes_sb_if_idle() --> will wait for journal_stop()
5) try_to_release_page() may fail and it does fail if one of page's bh was
pinned by journal
6) If we about to change page's mapping we MUST hold it's lock during entire
remapping procedure, this is true for both pages(original and donor one)
Fixes:
- Avoid (1) and (2) simply by temproraly drop uninitialized extent handling
optimization, this will be reimplemented later.
- Fix (3) by manually forcing page to uptodate state w/o dropping it's lock
- Fix (4) by rearranging existing locking:
from: journal_start(); ->write_begin
to: write_begin(); journal_extend()
- Fix (5) simply by checking retvalue
- Fix (6) by locking both (original and donor one) pages during extent swap
with help of mext_page_double_lock()
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Proper block swap for inodes with full journaling enabled is
truly non obvious task. In order to be on a safe side let's
explicitly disable it for now.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org
- Remove usless checks, because it is too late to check that inode != NULL
at the moment it was referenced several times.
- Double lock routines looks very ugly and locking ordering relays on
order of i_ino, but other kernel code rely on order of pointers.
Let's make them simple and clean.
- check that inodes belongs to the same SB as soon as possible.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org
blkdev_mmap() isn't used outside of fs/block_dev.c, mark it as
static.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This avoids cache line bouncing when many processes lock the semaphore
for read.
New percpu lock implementation
The lock consists of an array of percpu unsigned integers, a boolean
variable and a mutex.
When we take the lock for read, we enter rcu read section, check for a
"locked" variable. If it is false, we increase a percpu counter on the
current cpu and exit the rcu section. If "locked" is true, we exit the
rcu section, take the mutex and drop it (this waits until a writer
finished) and retry.
Unlocking for read just decreases percpu variable. Note that we can
unlock on a difference cpu than where we locked, in this case the
counter underflows. The sum of all percpu counters represents the number
of processes that hold the lock for read.
When we need to lock for write, we take the mutex, set "locked" variable
to true and synchronize rcu. Since RCU has been synchronized, no
processes can create new read locks. We wait until the sum of percpu
counters is zero - when it is, there are no readers in the critical
section.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The kernel may crash when block size is changed and I/O is issued
simultaneously.
Because some subsystems (udev or lvm) may read any block device anytime,
the bug actually puts any code that changes a block device size in
jeopardy.
The crash can be reproduced if you place "msleep(1000)" to
blkdev_get_blocks just before "bh->b_size = max_blocks <<
inode->i_blkbits;".
Then, run "dd if=/dev/ram0 of=/dev/null bs=4k count=1 iflag=direct"
While it is waiting in msleep, run "blockdev --setbsz 2048 /dev/ram0"
You get a BUG.
The direct and non-direct I/O is written with the assumption that block
size does not change. It doesn't seem practical to fix these crashes
one-by-one there may be many crash possibilities when block size changes
at a certain place and it is impossible to find them all and verify the
code.
This patch introduces a new rw-lock bd_block_size_semaphore. The lock is
taken for read during I/O. It is taken for write when changing block
size. Consequently, block size can't be changed while I/O is being
submitted.
For asynchronous I/O, the patch only prevents block size change while
the I/O is being submitted. The block size can change when the I/O is in
progress or when the I/O is being finished. This is acceptable because
there are no accesses to block size when asynchronous I/O is being
finished.
The patch prevents block size changing while the device is mapped with
mmap.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When performing an online resize, we add a bunch of groups at one time
in ext4_flex_group_add, so in most cases a lot of group descriptors
will be in the same group block. But in the end of this function,
update_backups will be called for every group descriptor and the same
block will be copied and journalled again and again. It is really a
waste.
Fix things so we only update a particular bg descriptor block once and
skip subsequent updates of the same block.
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
bh_submit_read() is responsible for unlock bh on endio. In addition,
we need to use bh_uptodate_or_lock() to avoid races.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Wrap the use of TIOCSRS485 and TIOCGRS485 in #ifdef so that we avoid
adding undefined IOCTLs to the ioctl pointer list as compatible
ioctls.
This change was motivated by a build error on a MIPS build.
tree: git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty.git
tty-next
head: ac57e7f38e
commit: 84c3b84860 [10/16] compat_ioctl:
Add RS-485 IOCTLs to the list
config: mips-fuloong2e_defconfig
All related error/warning messages:
fs/compat_ioctl.c:869:1: error: 'TIOCSRS485' undeclared here (not in a
function)
fs/compat_ioctl.c:870:1: error: 'TIOCGRS485' undeclared here (not in a
function)
vim +869 fs/compat_ioctl.c
863 COMPATIBLE_IOCTL(TIOCSPGRP)
864 COMPATIBLE_IOCTL(TIOCGPGRP)
865 COMPATIBLE_IOCTL(TIOCGPTN)
866 COMPATIBLE_IOCTL(TIOCSPTLCK)
867 COMPATIBLE_IOCTL(TIOCSERGETLSR)
868 COMPATIBLE_IOCTL(TIOCSIG)
> 869 COMPATIBLE_IOCTL(TIOCSRS485)
870 COMPATIBLE_IOCTL(TIOCGRS485)
871 #ifdef TCGETS2
872 COMPATIBLE_IOCTL(TCGETS2)
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In nfs4_create_sec_client, 'flavor' can hold a negative error
code (returned from nfs4_negotiate_security), even though it
is an 'enum' and hence unsigned.
The code is careful to cast it to an (int) before testing if it
is negative, however it doesn't cast to an (int) before calling
ERR_PTR.
On a machine where "void*" is larger than "int", this results in
the unsigned equivalent of -1 (e.g. 0xffffffff) being converted
to a pointer. Subsequent code determines that this is not
negative, and so dereferences it with predictable results.
So: cast 'flavor' to a (signed) int before passing to ERR_PTR.
cc: Benny Halevy <bhalevy@tonian.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
In case of error, the function rpcauth_create() returns ERR_PTR()
and never returns NULL pointer. The NULL test in the return value
check should be replaced with IS_ERR().
dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
...and make the default cache=strict as promised for 3.7.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
and add missed increments of failed async read and write requests.
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru>
Signed-off-by: Steve French <smfrench@gmail.com>
by making it __le64 rather than __u64 in FILE_AL_INFO structure.
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru>
Signed-off-by: Steve French <smfrench@gmail.com>
Some trivial endian fixes for the SMB2 code. One
warning remains which I asked Pavel to look at.
Reviewed-by: Pavel Shilovsky <piastry@etersoft.ru>
Signed-off-by: Steve French <smfrench@gmail.com>
Now that the merge of the remaining pieces needed for
SMB2 (SMB2.1 dialect) are in, and most test cases pass,
we can consider SMB2.1 EXPERIMENTAL rather than "BROKEN."
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Pavel Shilovsky <piastry@etersoft.ru>
Signed-off-by: Steve French <smfrench@gmail.com>
With SMB2 support, update from version 1.79 to 2.0 to make
it easier for users to recognize which version has SMB2 support.
Signed-off-by: Steve French <sfrench@us.ibm.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
