This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is only an API consolidation to make things more readable.
Instances of HZ / CONST are replaced by appropriate msecs_to_jiffies().
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes while CPU have some load and ath5k doing the wireless
interface reset the whole WiSoC completely freezes. Set of tests shows
that using atomic delay function while we wait interface reset helps to
avoid such freezes.
The easiest way to reproduce this issue: create a station interface,
start continous scan with wpa_supplicant and load CPU by something. Or
just create multiple station interfaces and put them all in continous
scan.
This patch partially reverts the commit 1846ac3dbe ("ath5k: Use
usleep_range where possible"), which replaces initial udelay()
by usleep_range().
I do not know actual source of this issue, but all looks like that HW
freeze is caused by transaction on internal SoC bus, while wireless
block is in reset state.
Also I should note that I do not know how many chips are affected, but I
did not see this issue with chips, other than AR5312.
CC: Jiri Slaby <jirislaby@gmail.com>
CC: Nick Kossifidis <mickflemm@gmail.com>
CC: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Fixes: 1846ac3dbe ("ath5k: Use usleep_range where possible")
Reported-by: Christophe Prevotaux <c.prevotaux@rural-networks.com>
Tested-by: Christophe Prevotaux <c.prevotaux@rural-networks.com>
Tested-by: Eric Bree <ebree@nltinc.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set the transmit rate for the keep-alive frames
as 1M/CCK when the current channel is in the
2GHz band.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Chips in the AR9003 family have a second TSF, which
needs to be cleared when putting the card to
sleep.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Setting the required configuration in the PCIE
WorkAround register needs to be done after all the
WoW parameters have been set.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch addresses several issues with the
ath9k_hw_wow_enable() routine:
* The usage of set/clr variables is removed. Writing
the required values to registers is cleaner.
* The shift value of 28 for the contention window field
in AR_WOW_PATTERN is incorrect, change it to 27.
* Disabling Keep Alive needs to be done based on the
LINK_CHANGE option. This is done unconditionally now,
fix this.
* The workaround for the D1/D3 issue is required only
for AR9462.
* The bitfield for enabling pattern matching for packets
less than 256 bytes has expanded for new chips, handle
this accordingly.
* General cleanup.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since the number of user patterns is higher for
newer chips, make sure that this is registered
during initialization.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Newer chips like WB222, WB335 support more than
8 user-configurable patterns. This patch adds
support for it by setting up the correct HW
registers.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver utilizes a FIFO buffer for RX descriptors. There are four places
in the code where it calculates the number of free slots. Several of those
locations do the calculation incorrectly. To fix these and to prevent future
mistakes, a common inline routine is created.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V3.18]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The hardware and firmware for the RTL8192EE utilize a FIFO list of
descriptors. There were some problems with the initial implementation.
The worst of these failed to detect that the FIFO was becoming full,
which led to the device needing to be power cycled. As this condition
is not relevant to most of the devices supported by rtlwifi, a callback
routine was added to detect this situation. This patch implements the
necessary changes in the pci handler, and the linkage into the appropriate
rtl8192ee routine.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V3.18]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The Altera mailbox allows for interprocessor communication. It supports
only one channel and work as either sender or receiver.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Before polling we just need to see if the TXDONE_BY_POLL bit
is set in txdone_method. There may be another bit (method)
specified as well, like TXDONE_BY_ACK.
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
In case of error, the function platform_create_bundle() returns
ERR_PTR() and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
The warning message when loading modules with a wrong signature has
two spaces in it:
"module verification failed: signature and/or required key missing"
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
parse_args call module parameters' .set handlers, which may use locks defined in the module.
So, these classes should be freed in case parse_args returns error(e.g. due to incorrect parameter passed).
Signed-off-by: Andrey Tsyvarev <tsyvarev@ispras.ru>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
These __ksymtab*/__kcrctab* sections currently have non-zero addresses.
Non-zero section addresses in a relocatable ELF confuse GDB and it ends
up not relocating all symbols when add-symbol-file is used on modules
which have exports. The kernel's module loader does not care about
these addresses, so let's just set them to zero.
Before:
$ readelf -S lib/notifier-error-inject.ko | grep 'Name\| __ksymtab_gpl'
[Nr] Name Type Addr Off Size ES Flg Lk Inf Al
[ 8] __ksymtab_gpl PROGBITS 0000000c 0001b4 000010 00 A 0 0 4
(gdb) add-symbol-file lib/notifier-error-inject.ko 0x500000 -s .bss 0x700000
add symbol table from file "lib/notifier-error-inject.ko" at
.text_addr = 0x500000
.bss_addr = 0x700000
(gdb) p ¬ifier_err_inject_dir
$3 = (struct dentry **) 0x0
After:
$ readelf -S lib/notifier-error-inject.ko | grep 'Name\| __ksymtab_gpl'
[Nr] Name Type Addr Off Size ES Flg Lk Inf Al
[ 8] __ksymtab_gpl PROGBITS 00000000 0001b4 000010 00 A 0 0 4
(gdb) add-symbol-file lib/notifier-error-inject.ko 0x500000 -s .bss 0x700000
add symbol table from file "lib/notifier-error-inject.ko" at
.text_addr = 0x500000
.bss_addr = 0x700000
(gdb) p ¬ifier_err_inject_dir
$3 = (struct dentry **) 0x700000
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
pnfs_layoutreturn_free_lseg_async() can also race with inode put in
the general case. We can now fix this, and also simplify the code.
Cc: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
This patch enables the ethertype Anti-Spoofing feature for affected
devices. It is configured such that LLDP packets sent by a VF will
be dropped.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change combines the reset and watchdog tasklets into a single task.
The advantage of this is that we can avoid multiple schedules of the reset
task when we have a reset event needed due to either the mailbox going down
or transmit packets being present on a link down.
CC: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the logic dealing with link down/up by breaking down the
link detection and up/down events into separate functions - similar to how these
events are handled in other drivers.
CC: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds code to allow for Tx hang checking. The idea is to provide
more robust debug info in the event of a transmit unit hang. Similar to the
logic in ixgbe.
CC: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the ordering of the shutdown path so that we attempt to
shutdown the rings more gracefully. Basically the big changes are that we
shutdown the main Rx filter in the case of Rx and we set the carrier_off
state in the case of Tx so that packets stop being delivered from outside
the driver. Then we shut down interrupts and NAPI. Finally we stop the
rings from performing DMA and clean them. This is a bit more graceful than
the previous path.
CC: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up the setting of vlan_features by enabling all features at once.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support VXLAN receive checksum offload in X550 hardware.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We always identify the PHY in our reset_hw path anyway so there is
no need to do it in get_invariants(). The reason I even noticed this
is that for new hardware (X550em) we don't assign some methods until
later in probe and calling phy.ops.read_reg could lead to a panic.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
My original patch 6a14ee0cfb "ixgbe: Add X550 support function pointers"
accidental set a default value for this structure member twice.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes couple of issues introduced by
commit 2b509c0cd2 ("ixgbe: cleanup ixgbe_ndo_set_vf_vlan")
- fix setting of the VLAN inside ixgbe_enable_port_vlan()
- disable the "hide VLAN" bit in PFQDE when port VLAN is disabled
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X550 provides RSS registers for configuring RSS per VF.
This patch introduces ixgbevf_setup_vfmrqc() which uses the VFRETA,
VFRSSRK and VFMRQC registers to configure RSS on X550.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables multiple queues and RSS support for the VF.
Maximum of 2 queues are supported due to available vectors.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe_set_sriov_queues() has the logic to allow multiple queues, this patch
just removes the limitation.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up prototypes that should have been defined
as static.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix two cases where variables are being set but not used.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh<Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, fm10k_update_xc_addr_pf has an issue where it does not
properly drop the upper-most four bits of the VLAN ID due to type
promotion. Resolve the issue not by masking off the bits, but by
throwing an error if the VLAN ID is out-of-bounds.
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no point in queueing EV_SYN/SYN_DROPPED on clock type change when
there are no events in the client's queue and doing so confuses tests in
libinput package, so let's not do that.
Reported-and-tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In we want to be able to call pnfs_send_layoutreturn() from within the
writeback path, we really want it to use GFP_NOFS in order to prevent
recursion.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
If we're sending an asynchronous layoutreturn, then we need to ensure
that the inode and the super block remain pinned.
Cc: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Reviewed-by: Peng Tao <tao.peng@primarydata.com>
If we're sending an asynchronous layoutcommit, then we need to ensure
that the inode and the super block remain pinned.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Reviewed-by: Peng Tao <tao.peng@primarydata.com>
If we have to do a return-on-close in the delegreturn code, then
we must ensure that the inode and super block remain referenced.
Cc: Peng Tao <tao.peng@primarydata.com>
Cc: stable@vger.kernel.org # 3.17.x
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Reviewed-by: Peng Tao <tao.peng@primarydata.com>
In acpi_table_parse(), pointer of the table to pass to handler() is
checked before handler() called, so remove all the duplicate NULL
check in the handler function.
CC: Tony Luck <tony.luck@intel.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We were missing a return statement in the PSL interrupt handler in the
case of an AFU error, which would trigger an "Unhandled CXL PSL IRQ"
warning. We do actually handle these type of errors (by notifying
userspace), so add the missing return IRQ_HANDLED so we don't throw
unecessary warnings.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If an AFU claims to have a configuration record but doesn't actually
contain a vendor and device ID, fail the AFU initialisation. Right now
this is just a way of politely letting AFU developers know that they
need to fix their config space, but later on we may expose the AFUs as
actual PCI devices in their own right and don't want to inadvertendly
expose an AFU with a bad config space.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
An AFU may optionally contain one or more PCIe like configuration
records, which can be used to identify the AFU.
This patch adds support for exposing the raw config space and the
vendor, device and class code under sysfs. These will appear in a
subdirectory of the AFU device corresponding with the configuration
record number, e.g.
cat /sys/class/cxl/afu0.0/cr0/vendor
0x1014
cat /sys/class/cxl/afu0.0/cr0/device
0x4350
cat /sys/class/cxl/afu0.0/cr0/class
0x120000
hexdump -C /sys/class/cxl/afu0.0/cr0/config
00000000 14 10 50 43 00 00 00 00 06 00 00 12 00 00 00 00 |..PC............|
00000010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
*
00000100
These files behave in much the same way as the equivalent files for PCI
devices, with one exception being that the config file is currently
read-only and restricted to the root user. It is not necessarily
required to be this strict, but we currently do not have a compelling
use-case to make it writable and/or world-readable, so I erred on the
side of being restrictive.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
this patch fixes following sparse warning:
vxge-config.c:4640:30: warning: Using plain integer as NULL pointer
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes following sparse warning:
interface.c:83:5: warning: symbol 'xenvif_poll' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes following sparse warning:
macb.c:2038:26: warning: symbol 'gem_ethtool_ops' was not declared. Should it be static?
Alongside drops exporting of gem_ethtool_ops as there is no need.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes following sparse warnings:
bnx2x_main.c:9172:6: warning: symbol 'bnx2x_stop_ptp' was not declared. Should it be static?
bnx2x_main.c:13321:6: warning: symbol 'bnx2x_register_phc' was not declared. Should it be static?
bnx2x_main.c:14638:5: warning: symbol 'bnx2x_enable_ptp_packets' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes following sparse warnings:
enic_main.c:92:28: warning: symbol 'mod_table' was not declared. Should it be static?
enic_main.c:109:28: warning: symbol 'mod_range' was not declared. Should it be static?
enic_main.c:1306:5: warning: symbol 'enic_busy_poll' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
