There are instances where the DMA engine stalls. The new code detects
such stalls and restarts DMA without needing a power reset.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.18]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware supplies two kinds of packets via the RX mechanism. Besides the
normal data received over the air, these packets may contain bluetooth status
and other information. The present code fails to detect which kind of
information was received.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V3.18]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initially, the routine to update the write point in the FIFO buffer was
coded to save CPU time by not doing the calculation every interrupt. This
was an error and results in TX hangs.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V3.18]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the buffer descriptor index exceeds 2, then a TX HANG condition
will result.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V3.18]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit e1a5848e33 ("ARM: 7924/1: mm: don't bother with reserved ttbr0
when running with LPAE") removed the use of the reserved TTBR0 value
for LPAE systems, since the ASID is held in the TTBR and can be updated
atomicly with the pgd of the next mm.
Unfortunately, this patch forgot to update flush_context, which
deliberately avoids marking the local active ASID as allocated, since we
used to switch via ASID zero and didn't need to allocate the ASID of
the previous mm. The side-effect of this is that we can allocate the
same ASID to the next mm and, between flushing the local TLB and updating
TTBR0, we can perform speculative TLB fills for userspace nG mappings
using the page table of the previous mm.
The consequence of this is that the next mm can erroneously hit some
mappings of the previous mm. Note that this was made significantly
harder to hit by a391263cd8 ("ARM: 8203/1: mm: try to re-use old ASID
assignments following a rollover") but is still theoretically possible.
This patch fixes the problem by removing the code from flush_context
that forces the allocated ASID to zero for the local CPU. Many thanks
to the Broadcom guys for tracking this one down.
Fixes: e1a5848e33 ("ARM: 7924/1: mm: don't bother with reserved ttbr0 when running with LPAE")
Cc: <stable@vger.kernel.org> # v3.14+
Reported-by: Raymond Ngun <rngun@broadcom.com>
Tested-by: Raymond Ngun <rngun@broadcom.com>
Reviewed-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For TKT238285 hardware issue which may cause txfifo store data twice can only
be caught on i.mx6dl, we use pio mode instead of DMA mode on i.mx6dl.
Fixes: f62caccd12 (spi: spi-imx: add DMA support)
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The bnep_get_device function may be triggered by an ioctl just after a
connection has gone down. In such a case the respective L2CAP chan->conn
pointer will get set to NULL (by l2cap_chan_del). This patch adds a
missing NULL check for this case in the bnep_get_device() function.
Reported-by: Patrik Flykt <patrik.flykt@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The quota threshold should be reduced to 4 to update the
firmware more frequently.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
After commit e9d8b2c296 (xen-netback:
disable rogue vif in kthread context), a fatal (protocol) error would
leave the guest Rx thread spinning, wasting CPU time. Commit
ecf08d2dbb (xen-netback: reintroduce
guest Rx stall detection) made this even worse by removing a
cond_resched() from this path.
Since a fatal error is non-recoverable, just allow the guest Rx thread
to exit. This requires taking additional refs to the task so the
thread exiting early is handled safely.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reported-by: Julien Grall <julien.grall@linaro.org>
Tested-by: Julien Grall <julien.grall@linaro.org>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit de966c5928 (net/mlx4_core: Support more than 64 VFs) was meant to
allow up to 126 VFs. However, due to leaving MLX4_MFUNC_MAX too low, using
more than 80 VFs resulted in memory corruptions (and Oopses) when more than
80 VFs were requested. In addition, the number of slaves was left too high.
This commit fixes these issues.
Fixes: de966c5928 ("net/mlx4_core: Support more than 64 VFs")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bug here is that we use "Reject" as the index into the cau_t[] array
in the else path. Since the cau_t[] has 9 elements if Reject == 9 then
we are reading beyond the end of the array.
My understanding of the code is that it's saying that if Reject is 1 or
too high then that's invalid and we should hang up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree,
they are:
1) Validate hooks for nf_tables NAT expressions, otherwise users can
crash the kernel when using them from the wrong hook. We already
got one user trapped on this when configuring masquerading.
2) Fix a BUG splat in nf_tables with CONFIG_DEBUG_PREEMPT=y. Reported
by Andreas Schultz.
3) Avoid unnecessary reroute of traffic in the local input path
in IPVS that triggers a crash in in xfrm. Reported by Florian
Wiessner and fixes by Julian Anastasov.
4) Fix memory and module refcount leak from the error path of
nf_tables_newchain().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-By: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladislav Yasevich says:
====================
ipv6: Add lockless UDP send path
This series introduces a lockless UDPv6 send path similar to
what Herbert Xu did for IPv4 a while ago.
There are some difference from IPv4. IPv6 caching for flow
label is a bit different, as well as it requires another cork
cork structure that holds the IPv6 ancillary data.
Please take a look.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currntly, if we are not doing UFO on the packet, all UDP
packets will start with CHECKSUM_NONE and thus perform full
checksum computations in software even if device support
IPv6 checksum offloading.
Let's start start with CHECKSUM_PARTIAL if the device
supports it and we are sending only a single packet at
or below mtu size.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds the same functionaliy to IPv6 that
commit 903ab86d19
Author: Herbert Xu <herbert@gondor.apana.org.au>
Date: Tue Mar 1 02:36:48 2011 +0000
udp: Add lockless transmit path
added to IPv4.
UDP transmit path can now run without a socket lock,
thus allowing multiple threads to send to a single socket
more efficiently.
This is only used when corking/MSG_MORE is not used.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we can individually construct IPv6 skbs to send, add a
udpv6_send_skb() function to populate the udp header and send the
skb. This allows udp_v6_push_pending_frames() to re-use this
function as well as enables us to add lockless sendmsg() support.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit is very similar to
commit 1c32c5ad6f
Author: Herbert Xu <herbert@gondor.apana.org.au>
Date: Tue Mar 1 02:36:47 2011 +0000
inet: Add ip_make_skb and ip_finish_skb
It adds IPv6 version of the helpers ip6_make_skb and ip6_finish_skb.
The job of ip6_make_skb is to collect messages into an ipv6 packet
and poplulate ipv6 eader. The job of ip6_finish_skb is to transmit
the generated skb. Together they replicated the job of
ip6_push_pending_frames() while also provide the capability to be
called independently. This will be needed to add lockless UDP sendmsg
support.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to append data to arbitrary queue. This
will be needed later to implement lockless UDP sends.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull IPv6 cork initialization into its own function that
can be re-used. IPv6 specific cork data did not have an
explicit data structure. This patch creats eone so that
just ipv6 cork data can be as arguemts. Also, since
IPv6 tries to save the flow label into inet_cork_full
tructure, pass the full cork.
Adjust ip6_cork_release() to take cork data structures.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Add support for IEEE ets & pfc api.
* Fix bug that resulted in incorrect bandwidth percentage being returned for
CEE peers
* Convert pfc enabled info from firmware format to what dcbnl expects before
returning
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ARM has 32-byte cache lines, which according to the comment in
the init registers function seems to work best with the default
value of 0x4800 that is also used on sparc and parisc.
This adds ARM to the same list, to use that default but no
longer warn about it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hip04 ethernet driver causes a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/hisilicon/hip04_eth.o
see include/linux/module.h for more information
This adds the license as "GPL", which matches the header of the file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update netlink_mmap.txt wrt. commit 4682a03586
("netlink: Always copy on mmap TX.").
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
One deployment requirement of DCTCP is to be able to run
in a DC setting along with TCP traffic. As Glenn Judd's
NSDI'15 paper "Attaining the Promise and Avoiding the Pitfalls
of TCP in the Datacenter" [1] (tba) explains, one way to
solve this on switch side is to split DCTCP and TCP traffic
in two queues per switch port based on the DSCP: one queue
soley intended for DCTCP traffic and one for non-DCTCP traffic.
For the DCTCP queue, there's the marking threshold K as
explained in commit e3118e8359 ("net: tcp: add DCTCP congestion
control algorithm") for RED marking ECT(0) packets with CE.
For the non-DCTCP queue, there's f.e. a classic tail drop queue.
As already explained in e3118e8359, running DCTCP at scale
when not marking SYN/SYN-ACK packets with ECT(0) has severe
consequences as for non-ECT(0) packets, traversing the RED
marking DCTCP queue will result in a severe reduction of
connection probability.
This is due to the DCTCP queue being dominated by ECT(0) traffic
and switches handle non-ECT traffic in the RED marking queue
after passing K as drops, where K is usually a low watermark
in order to leave enough tailroom for bursts. Splitting DCTCP
traffic among several queues (ECN and non-ECN queue) is being
considered a terrible idea in the network community as it
splits single flows across multiple network paths.
Therefore, commit e3118e8359 implements this on Linux as
ECT(0) marked traffic, as we argue that marking all packets
of a DCTCP flow is the only viable solution and also doesn't
speak against the draft.
However, recently, a DCTCP implementation for FreeBSD hit also
their mainline kernel [2]. In order to let them play well
together with Linux' DCTCP, we would need to loosen the
requirement that ECT(0) has to be asserted during the 3WHS as
not implemented in FreeBSD. This simplifies the ECN test and
lets DCTCP work together with FreeBSD.
Joint work with Daniel Borkmann.
[1] https://www.usenix.org/conference/nsdi15/technical-sessions/presentation/judd
[2] 8ad8794452
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Glenn Judd <glenn.judd@morganstanley.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn says:
====================
net-timestamp: blinding
Changes
(v2 -> v3)
- rebase only: v2 did not make it to patchwork / netdev
(v1 -> v2)
- fix capability check in patch 2
this could be moved into net/core/sock.c as sk_capable_nouser()
(rfc -> v1)
- dropped patch 4: timestamp batching
due to complexity, as discussed
- dropped patch 5: default mode
because it does not really cover all use cases, as discussed
- added documentation
- minor fix, see patch 2
Two issues were raised during recent timestamping discussions:
1. looping full packets on the error queue exposes packet headers
2. TCP timestamping with retransmissions generates many timestamps
This RFC patchset is an attempt at addressing both without breaking
legacy behavior.
Patch 1 reintroduces the "no payload" timestamp option, which loops
timestamps onto an empty skb. This reduces the pressure on SO_RCVBUF
from looping many timestamps. It does not reduce the number of recv()
calls needed to process them. The timestamp cookie mechanism developed
in http://patchwork.ozlabs.org/patch/427213/ did, but this is
considerably simpler.
Patch 2 then gives administrators the power to block all timestamp
requests that contain data by unprivileged users. I proposed this
earlier as a backward compatible workaround in the discussion of
net-timestamp: pull headers for SOCK_STREAM
http://patchwork.ozlabs.org/patch/414810/
Patch 3 only updates the txtimestamp example to test this option.
Verified that with option '-n', length is zero in all cases and
option '-I' (PKTINFO) stops working.
====================
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Demonstrate how SOF_TIMESTAMPING_OPT_TSONLY can be used and
test the implementation.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx timestamps are looped onto the error queue on top of an skb. This
mechanism leaks packet headers to processes unless the no-payload
options SOF_TIMESTAMPING_OPT_TSONLY is set.
Add a sysctl that optionally drops looped timestamp with data. This
only affects processes without CAP_NET_RAW.
The policy is checked when timestamps are generated in the stack.
It is possible for timestamps with data to be reported after the
sysctl is set, if these were queued internally earlier.
No vulnerability is immediately known that exploits knowledge
gleaned from packet headers, but it may still be preferable to allow
administrators to lock down this path at the cost of possible
breakage of legacy applications.
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
Changes
(v1 -> v2)
- test socket CAP_NET_RAW instead of capable(CAP_NET_RAW)
(rfc -> v1)
- document the sysctl in Documentation/sysctl/net.txt
- fix access control race: read .._OPT_TSONLY only once,
use same value for permission check and skb generation.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add timestamping option SOF_TIMESTAMPING_OPT_TSONLY. For transmit
timestamps, this loops timestamps on top of empty packets.
Doing so reduces the pressure on SO_RCVBUF. Payload inspection and
cmsg reception (aside from timestamps) are no longer possible. This
works together with a follow on patch that allows administrators to
only allow tx timestamping if it does not loop payload or metadata.
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
Changes (rfc -> v1)
- add documentation
- remove unnecessary skb->len test (thanks to Richard Cochran)
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug where vnet_skb_shape() didn't set the already-selected
queue mapping when a packet copy was required. This results in using the
wrong queue index for stops/starts, hung tx queues and watchdog timeouts
under heavy load.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently qlge_update_hw_vlan_features() will always first put the
interface down, then update features and then bring it up again. But it
is possible to hit this code while the adapter is down and this causes a
non-paired call to napi_disable(), which will get stuck.
This patch fixes it by skipping these down/up actions if the interface
is already down.
Fixes: a45adbe8d3 ("qlge: Enhance nested VLAN (Q-in-Q) handling.")
Cc: Harish Patil <harish.patil@qlogic.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three small fixes that came up during last week, nothing scary:
- Accidently incremented a counter instead of decrementing it (copy-paste error)
- Module parameter of max num of queues must be at least 1 and not 0
- Don't do BUG() as a result from wrong user input
* tag 'drm-amdkfd-fixes-2015-02-02' of git://people.freedesktop.org/~gabbayo/linux:
drm/amdkfd: Don't create BUG due to incorrect user parameter
drm/amdkfd: max num of queues can't be 0
drm/amdkfd: Fix bug in accounting of queues
One last round of fixes for radeon for 3.19:
- fix some fallout from the reservation object integration on the
test/benchmark options
- fix a crash in the gpu vm code if gfx init fails
- fix a pll issue that leads to a blank screen on older IGP parts
* 'drm-fixes-3.19' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix the crash in test functions
drm/radeon: fix the crash in benchmark functions
drm/radeon: properly set vm fragment size for TN/RL
drm/radeon: don't init gpuvm if accel is disabled (v3)
drm/radeon: fix PLLs on RS880 and older v2
The transaction notifies the host (DH) that an action
is required to manage a specific Secure Element application.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The transaction notifies the host (DH) that an action
is required to manage a specific Secure Element application.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When receiving an interface activation notification, if
the RF interface is NCI_RF_INTERFACE_NFCEE_DIRECT, we
need to ignore the following parameters and change the NCI
state machine to NCI_LISTEN_ACTIVE. According to the NCI
specification, the parameters should be 0 and shall be
ignored.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The NFCC sends an NCI_OP_RF_NFCEE_ACTION_NTF notification
to the host (DH) to let it know that for example an RF
transaction with a payment reader is done.
For now the notification handler is empty.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC_EVT_TRANSACTION is sent through netlink in order for a
specific application running on a secure element to notify
userspace of an event. Typically the secure element application
counterpart on the host could interpret that event and act
upon it.
Forwarded information contains:
- SE host generating the event
- Application IDentifier doing the operation
- Applications parameters
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The st21nfcb chipset has 3 SWP (Single Wire Protocol) lines and
supports up to 3 secure elements (UICC/eSE and µSD in the future).
Some st21nfcb firmware does not support the nci command
nci_nfcee_mode_set(NCI_NFCEE_DISABLE). For this reason, we assume
2 secures elements are always present (UICC and eSE).
They will be added to the SE list once successfully activated and
they will be available only after running through enable_se
handler or when the poll in listen mode is started.
During initialization, the white_list will be always set assuming
both UICC & eSE are present.
On eSE activation, the ATR bytes are fetched to build the command
exchange timeout.
The se_io hook will allow to transfer data over SWP. 2 kind of
events may appear data is sent over:
- ST21NFCB_EVT_TRANSMIT_DATA when receiving an apdu answer
- ST21NFCB_EVT_WTX_REQUEST when the secure element needs more time
than expected to process a command. If this timeout expires, we
send a software reset, and then a hardware one if it still fails.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
According to the NCI specification, one can use HCI over NCI
to talk with specific NFCEE. The HCI network is viewed as one
logical NFCEE.
This is needed to support secure element running HCI only
firmwares embedded on an NCI capable chipset, like e.g. the
st21nfcb.
There is some duplication between this piece of code and the
HCI core code, but the latter would need to be abstracted even
more to be able to use NCI as a logical transport for HCP packets.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to communicate with an NFCEE, we need to open a logical
connection to it, by sending the NCI_OP_CORE_CONN_CREATE_CMD
command to the NFCC. It's left up to the drivers to decide when
to close an already opened logical connection.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFCEEs can be enabled or disabled by sending the
NCI_OP_NFCEE_MODE_SET_CMD command to the NFCC. This patch
provides an API for drivers to enable and disable e.g. their
NCI discoveredd secure elements.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFCEEs (NFC Execution Environment) have to be explicitly
discovered by sending the NCI_OP_NFCEE_DISCOVER_CMD
command. The NFCC will respond to this command by telling
us how many NFCEEs are connected to it. Then the NFCC sends
a notification command for each and every NFCEE connected.
Here we implement support for sending
NCI_OP_NFCEE_DISCOVER_CMD command, receiving the response
and the potential notifications.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The current NCI core only support the RF static connection.
For other NFC features such as Secure Element communication, we
may need to create logical connections to the NFCEE (Execution
Environment.
In order to track each logical connection ID dynamically, we add a
linked list of connection info pointers to the nci_dev structure.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This extended return parameters struct conflicts with the new Read Local
OOB Extended Data command definition. To avoid the conflict simply
rename the old "extended" version to the normal one and update the code
appropriately to take into account the two possible response PDU sizes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
radeon_copy_dma and radeon_copy_blit must be called with
a valid reservation object. Otherwise a crash will be provoked.
We borrow the object from vram BO.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=88464
Cc: stable@vger.kernel.org
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
radeon_copy_dma and radeon_copy_blit must be called with
a valid reservation object. Otherwise a crash will be provoked.
We borrow the object from destination BO.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=88464
Cc: stable@vger.kernel.org
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
