I tested with the AX88179 usb dongle, if without .reset_resume hook,
after S3/S4 resume you have to enable network interface or reload the
dirver module manually otherwise the network interface can not work.
Signed-off-by: David Chang <dchang@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct a typo in description of driver_info, it should be Gigabit
Signed-off-by: David Chang <dchang@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d2d68ba9 (ipv4: Cache input routes in fib_info nexthops)
assmued that "locally destined, and routed packets, never trigger
PMTU events or redirects that will be processed by us".
However, it seems that tunnel devices do trigger PMTU events in certain
cases. At least ip_gre, ip6_gre, sit, and ipip do use the inner flow's
skb_dst(skb)->ops->update_pmtu to propage mtu information from the
outer flows. These can cause the inner flow mtu to be decreased. If
next hop exceptions are not consulted for pmtu, IP fragmentation will
not be done properly for these routes.
It also seems that we really need to have the PMTU information always
for netfilter TCPMSS clamp-to-pmtu feature to work properly.
So for the time being, cache separate copies of input routes for
each next hop exception.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC3590/RFC3810 specifies we should resend MLD reports as soon as a
valid link-local address is available.
We now use the valid_ll_addr_cnt to check if it is necessary to resend
a new report.
Changes since Flavio Leitner's version:
a) adapt for valid_ll_addr_cnt
b) resend first reports directly in the path and just arm the timer for
mc_qrv-1 resends.
Reported-by: Flavio Leitner <fleitner@redhat.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: David Stevens <dlstevens@us.ibm.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To reduce the number of unnecessary router solicitations, MLDv2 and IGMPv3
messages we need to track the number of valid (as in non-optimistic,
no-dad-failed and non-tentative) link-local addresses. Therefore, this
patch implements a valid_ll_addr_cnt in struct inet6_dev.
We now only emit router solicitations if the first link-local address
finishes duplicate address detection.
The changes for MLDv2 and IGMPv3 are in a follow-up patch.
While there, also simplify one if statement(one minor nit I made in one
of my previous patches):
if (!...)
do();
else
return;
<<into>>
if (...)
return;
do();
Cc: Flavio Leitner <fbl@redhat.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Cc: David Stevens <dlstevens@us.ibm.com>
Suggested-by: David Stevens <dlstevens@us.ibm.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A simple semantic change, when a slave's MAC is cloned by the bond
master then set addr_assign_type to NET_ADDR_STOLEN instead of
NET_ADDR_SET. Also use bond_set_dev_addr() in BOND_FOM_ACTIVE mode
to change the bond's MAC address because the assign_type has to be
set properly.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In struct bonding there's a member called dev_addr_from_first which is
used to denote when the bond dev should clone the first slave's MAC
address but since we have netdev's addr_assign_type variable that is not
necessary. We clone the first slave's MAC each time we have a random MAC
set to the bond device. This has the nice side-effect of also fixing an
inconsistency - when the MAC address of the bond dev is set after its
creation, but prior to having slaves, it's not kept and the first slave's
MAC is cloned. The only way to keep the MAC was to create the bond device
with the MAC address set (e.g. through ip link). In all cases if the
bond device is left without any slaves - its MAC gets reset to a random
one as before.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a member called setup_by_slave in struct bonding to denote if the
bond dev has different type than ARPHRD_ETHER, but that is already denoted
in bond's netdev type variable if it was setup by the slave, so use that
instead of the member.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since (c05cdb1 netlink: allow large data transfers from user-space),
netlink splats if it invokes skb_clone on large netlink skbs since:
* skb_shared_info was not correctly initialized.
* skb->destructor is not set in the cloned skb.
This was spotted by trinity:
[ 894.990671] BUG: unable to handle kernel paging request at ffffc9000047b001
[ 894.991034] IP: [<ffffffff81a212c4>] skb_clone+0x24/0xc0
[...]
[ 894.991034] Call Trace:
[ 894.991034] [<ffffffff81ad299a>] nl_fib_input+0x6a/0x240
[ 894.991034] [<ffffffff81c3b7e6>] ? _raw_read_unlock+0x26/0x40
[ 894.991034] [<ffffffff81a5f189>] netlink_unicast+0x169/0x1e0
[ 894.991034] [<ffffffff81a601e1>] netlink_sendmsg+0x251/0x3d0
Fix it by:
1) introducing a new netlink_skb_clone function that is used in nl_fib_input,
that sets our special skb->destructor in the cloned skb. Moreover, handle
the release of the large cloned skb head area in the destructor path.
2) not allowing large skbuffs in the netlink broadcast path. I cannot find
any reasonable use of the large data transfer using netlink in that path,
moreover this helps to skip extra skb_clone handling.
I found two more netlink clients that are cloning the skbs, but they are
not in the sendmsg path. Therefore, the sole client cloning that I found
seems to be the fib frontend.
Thanks to Eric Dumazet for helping to address this issue.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows to switch the netns when packet is encapsulated or
decapsulated. In other word, the encapsulated packet is received in a netns,
where the lookup is done to find the tunnel. Once the tunnel is found, the
packet is decapsulated and injecting into the corresponding interface which
stands to another netns.
When one of the two netns is removed, the tunnel is destroyed.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of this new function is to perform all needed cleanup before sending
an skb into another netns.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC drivers/net/wireless/ath/ath10k/mac.o
drivers/net/wireless/ath/ath10k/mac.c: In function ‘chan_to_phymode’:
drivers/net/wireless/ath/ath10k/mac.c:229:3: warning: enumeration value ‘NL80211_CHAN_WIDTH_5’ not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/mac.c:229:3: warning: enumeration value ‘NL80211_CHAN_WIDTH_10’ not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/mac.c:247:3: warning: enumeration value ‘NL80211_CHAN_WIDTH_5’ not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/mac.c:247:3: warning: enumeration value ‘NL80211_CHAN_WIDTH_10’ not handled in switch [-Wswitch]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed so the interface combination can still be
validated when CONFIG_MAC80211_MESH is not enabled.
Otherwise wiphy registration fails.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the code of the receive path some code was dealing with how
things were done in older kernels. Not really needed for an
upstream driver.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the receive path a spinlock is taken upon parsing the TLV signal
header. This moves to locking to the TLV handling functions where
it protects the data structures.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trivial cleanup of debug messages.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Transmit packets needs to be tagged in order to receive a tx status
feedback from the firmware. Determine the tag in the netdev transmit
callback instead of determining the tag just before transfer to the
device. This reduces the number of exception flows and hence makes
the driver code simpler.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DMA engine of some old SDIO host controllers require block size alignment for
data length of each scatterlist item. This patch introduces an intermediate
buffer list to support this kind of platform. It decreases the throughput
because of an extra memcpy in critical data path. So don't turn this on unless
it's necessary.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce a unified dongle backplane address preparation function
brcmf_sdio_addrprep to replace duplicate address prep code.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove SDIO_REQ_ASYNC from brcmfmac since it is not being used.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Used NL80211_NUM_ACS to indicate the BCMC fifo used in the driver
which has the same value now, but it is a bad idea relying on that.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When getting a transmit packet from the networking layer simply
enqueue the packet unconditional and have it handled by the dequeue
worker. The transfer of the packet to the bus-specific driver part
is now done from one context.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows enabling support for extra hardware with just a module
param, without kernel/module recompilation.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Apparently HW doesn't require us to generate MMIC
for TKIP suite.
Each frame was 8 bytes longer than it should be
and some APs would drop frames that exceed 1520
bytes of 802.11 payload. This could be observed
during throughput tests or fragmented IP traffic.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nonsense channel flags were being set.
Although it doesn't seem this was visible to the
user the patch makes sure that channel
availability won't be crippled in the future if
ath_common behaviour changes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Irqs were not freed up correctly upon msi-x setup
failure.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code writes the default_power2 value into the TX field
of the RFCSR50 register, however the condition in the if
statement uses default_power1. Due to this, wrong TX power
value might be written into the register.
Use the correct value in the condition to fix the issue.
Compile tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: stable@vger.kernel.org # 3.10
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 3T/3R devices are using the tertiary PAs/LNAs
however those are never turned on. Fix the code to
turn on those on for such devices.
Also modify the code to use switch statements to
improve readability.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The secondary PAs/LNAs are turned on only for 2T/2R
devices, however these are used for 3T/3R devices as
well. Always turn those on if the device uses more
than one tx/rx chains.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ralink 3T chipsets are using a different EEPROM
layout than the others. The EEPROM on these devices
contain more data than the others which does not fit
into 272 byte which the rt2800 driver actually uses.
The Ralink reference driver defines EEPROM_SIZE to
512/1024 bytes for PCI/USB devices respectively.
Increase the EEPROM_SIZE constant to 512 bytes, in
order to make room for EEPROM data of 3T devices.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
of_match_ptr() eliminates having an #ifdef returning NULL for the case
when OF is disabled.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As there are no more users of the flexcan platform file, let's remove it.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Instead of using a GPIO to turn on/off the CAN transceiver, it is better to
use a regulator as some systems may use a PMIC to power the CAN transceiver.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As there are no imx in-tree users of flexcan_platform_data, this patch removes
the possibility to register a flexcan device with platform data.
The functionality to swith on/off CAN transceivers is added to DT via
regulators in a later patch.
Compile time tested with imx_v4_v5_defconfig and imx_v6_v7_defconfig.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add ethtool operation to read RMON registers.
Tested against net-next on i.MX28.
v2: make conditional on #ifndef CONFIG_M5272
Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new tokenized address gets installed we send out just one
router solicition. We should send out `rtr_solicits' in case one router
advertisment got lost.
So, rearm the timer as we do in addrconf_dad_complete.
Cc: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 32b8a8e59c "sit: add IPv4 over IPv4 support",
tunnel->parms.iph.protocol is 0 when both 4in4 and 6in4 are setup, but
xfrm_lookup() is called only when proto is != 0, thus we need to pass the real
value.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
Just one patch this time.
1) Drop packets when the matching SA is in larval state and add a
statistic counter for that. From Fan Du.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
no real problem is fixed, just save a few bytes in
net_namespace structure.
Signed-off-by: JunweiZhang <junwei.zhang@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
ip_vs.h is not necessary for sysctl_binary.c.
prepare for the next patch to avoid compile issue.
Signed-off-by: JunweiZhang <junwei.zhang@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Add sync_persist_mode flag to reduce sync traffic
by syncing only persistent templates.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Tested-by: Aleksey Chudov <aleksey.chudov@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
By default the SH scheduler rejects connections that are hashed onto a
realserver of weight 0. This patch adds a flag to make SH choose a
different realserver in this case, instead of rejecting the connection.
The patch also adds a flag to make SH include the source port (TCP, UDP,
SCTP) in the hash as well as the source address. This basically allows
for deterministic round-robin load balancing (i.e., where any director
in a cluster of directors with identical config will send the same
packet the same way).
The flags are service flags (IP_VS_SVC_F_SCHED*) so that these options
can be set per service. They are set using a new option to ipvsadm.
Signed-off-by: Alexander Frolkin <avf@eldamar.org.uk>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Drop SCTP connections under load (dropentry context) depending
on the protocol state, just like for TCP: INIT conns are
dropped immediately, established are dropped randomly while
connections in progress or shutdown are skipped.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Convert the SCTP state table, so that it is more readable.
Change the states to be according to the diagram in RFC 2960
and add more states suitable for middle box. Still, such
change in states adds incompatibility if systems in sync
setup include this change and others do not include it.
With this change we also have proper transitions in INPUT-ONLY
mode (DR/TUN) where we see packets only from client. Now
we should not switch to 10-second CLOSED state at a time
when we should stay in ESTABLISHED state.
The short names for states are because we have 16-char space
in ipvsadm and 11-char limit for the connection list format.
It is a sequence of the TCP implementation where the longest
state name is ESTABLISHED.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
This adds support for sloppy TCP and SCTP modes to IPVS.
When enabled (sysctls net.ipv4.vs.sloppy_tcp and
net.ipv4.vs.sloppy_sctp), allows IPVS to create connection state on any
packet, not just a TCP SYN (or SCTP INIT).
This allows connections to fail over from one IPVS director to another
mid-flight.
Signed-off-by: Alexander Frolkin <avf@eldamar.org.uk>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
