len has been initialized with a value of 0 and buf_len with 4096. There
is no way that this condition (len > buf_len) can be true now.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some of the parameter like tx/rx chain mask, number of htt tx desc,
qcache active peer count, etc goes via wmi init cmd to qca4019 firmware
are different.
To make use of 10.4 gen_init function for qca4019, change wmi service
ready handler and 10.4 wmi init functions to adapt qca4019 specific
init values.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add a new entry in hw_params_list for qca4019 with list of
it's own details.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Abstraction layer for vdev subtype is added to solve
subtype mismatch and to give flexible compatibility
among different firmware revisions.
For instance, 10.2 and 10.4 firmware has different
definition of their vdev subtypes for Mesh.
10.4 defined subtype 6 for 802.11s Mesh while 10.2 uses 5.
Hence use the abstraction API to get right subtype to use.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Interface type P2P_GO can be checked by either arvif->vdev_type
and arvif->vdev_subtype or vif->type and vif->p2p.
Use later one to avoid more cpu consumption that could happen
when subtype abstraction layer change is introduced.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Update 10.4 WMI service map to sync to the latest 10.4 firmware
as of 1/20/2016.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WMI_10_4_SERVICE_MESH bit is for non IEEE802.11s Mesh.
Hence rename it to WMI_10_4_SERVICE_MESH_NON_11S.
Also add _11S as post-fix to each of WMI_SERVICE_MESH and
WMI_VDEV_SUBTYPE_MESH specifying the service is for 11s Mesh.
This will help users to distinguish 11s Mesh from non 11s Mesh.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Like how pci.c exposes hif ops for the bus specific operation,
expose similar hif ops table for ahb with all required functions
linked to it. Many ath10k_pci_* functions are reused here in hif ops
table. If something is not sharable, new functions are added for ahb
and linked to hif ops table.
Finally, make ath10k_ahb_probe/remove() to perform what is expected
out of it.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add function to gather resources required for qca4019 to operate
(memory, irq, dma setting, clock init , rest control init) and
function release those resources when it's not needed.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add irq related functions to register,handle,release,disable interrupt.
qca4019 supports msi interrupt, but it has the problem. Until the issue
gets sorted out, only legacy interrupt model is enabled and used.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add function to perform chip halt sequence and function to halt axi
bus in ahb module. Mainly used in the scenario like driver unload.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To perform reset on qca4019 wifi, multiple reset lines needs
to be toggled in a sequence with help of reset controller support
in the kernel. This patch adds functions to reset control init/deinit
and release reset.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
pre qca4019 chipsets has/uses internal clock generator for
the operation. But, qca4019 uses external clocks supplied from
outside of target (ie, outside of wifi core). Three different clocks
(cmd clock, ref clock, rtc clock) comes into picture in qca4019.
All those clocks needs to configured with help of global clock
controller (gcc) to make qca4019 functioning.
Add functions for clock init/deinit, clock enable/disable in ahb.
This is just a preparation, functions added in this patch will be
used in later patches.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca4019 deals with below register memory region to control the clock,
reset, etc.
- Memory to control wifi core
- gcc (outside of wifi)
- tcsr (outside of wifi)
Add new helper functions to perform read/write in above registers
spaces. Actual ioremap for above registers are done in later patch.
Struct ath10k_ahb is introduced to maintain ahb specific info and
memory this struct will be allocated in the continuation of struct
ath10k_pci (again, memory ath10k_ahb is allocated in the later patch).
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New register table is added for qca4019 to tell about it's
register mapping details.
Nothing much other than this.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca4019 uses ahb instead of pci where it slightly differs in device
enumeration, clock control, reset control, etc. Good thing is that
ahb also uses copy engine for the data transaction. So, the most of
the stuff implemented in pci.c/ce.c are reusable in ahb case too.
Device enumeration in ahb case comes through platform driver/device
model. All resource details like irq, memory map, clocks, etc for
qca4019 can be fetched from of_node of platform device.
Simply flow would look like,
device tree => platform device (kernel) => platform driver (ath10k)
Device tree entry will have all qca4019 resource details and the same
info will be passed to kernel. Kernel will prepare new platform device
for that entry and expose DT info to of_node in platform device.
Later, ath10k would register platform driver with unique compatible name
and then kernels binds to corresponding compatible entry & calls ath10k
ahb probe functions. From there onwards, ath10k will take control of it
and move forward.
New bool flag CONFIG_ATH10K_AHB is added in Kconfig to conditionally
enable ahb support in ath10k. On enabling this flag, ath10k_pci.ko
will have ahb support. This patch adds only basic skeleton and few
macros to support ahb in the context of qca4019.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some of the code present in ath10k_pci_{probe|remove} are reusable
in ahb case too. To avoid code duplication, move reusable code to
new functions. Later, those new functions can be called from ahb
module's probe and exit functions.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_pci_read32/write32() does work more specific to
PCI by ensuring pci wake/sleep for every read and write.
There is a plan to use most of stuff available in pci.c
(irq stuff, copy engine, etc) for AHB case. Such kind
of pci wake/sleep for every read/write is not required
in AHB case (qca4019). All those reusable areas in pci.c
and ce.c calls ath10k_pci_read32/write32() for low level
read and write.
In fact, ath10k_pci_read32/write32() should do what it does
today for PCI case. But for AHB, it has to do differently.
To make ath10k_pci_read32/write32() more generic, new function
pointers are added in ar_pci for the function which does
operation more close to the bus. Later, corresponding bus
specific read and write function will be mapped to that.
ath10k_pci_read32/write32() are changed to call directly
those function pointers without worrying which bus underlying
to it. Also, the function to get number of bank is changed
in the same way.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some of static functions present in pci.c file are reusable
in ahb (qca4019) case. Remove static word for those reusable
functions and have those function prototype declaration in
pci.h file. So that, pci.h header file can be included in
ahb module and reused. There is no functionality changes done
in this patch.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This allows to use the new firmware which
implements the new tx data path. Without this
patch firmware supporting new tx path stops
responding shortly after booting.
This patch doesn't implement the entire pull-push
logic available in the new firmware. This will be
done in subsequent patches.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes the code easier to extend and re-use.
While at it fix _warn to _err. Other than that
there are no functional changes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This feature flag will be used for firmware which
supports pull-push model where host shares it's
software queue state with firmware and firmware
generates fetch requests telling host which queues
to dequeue tx from.
Primary function of this is improved MU-MIMO
performance with multiple clients.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
These definitions are associated with some
improvements upcomming for 10.4 and QCA99X0.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The p2p NOA never been supported at 10.2.4 FW, remove it to avoid SWBA
event parse error for multi beacon interval case.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add debugfs support for per client total rx duration, track this
via the report of Peer stats rx duration reported for every 500ms
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Register for 500ms as periodic peer stats update period,
and parameters like rx_duration that needs to be tracked
in host can be achieved by this provision, also periodic
stats update is the future of fw_stats and shall be extended
for pdev / vdev stats irrespecitive PEER_STATS service is enabled
or not
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
[kvalo@qca.qualcomm.com: fix a checkpatch warning]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable support for periodic peer stats update when peer stats
service is enabled. The host to update the peer stats received
from the firmware periodically, since firmware will reset this to zero
after sometime (due to memory constraints)
While enabling periodic peer / vdev stats cleanup the existing
list in debugfs if max limit is reached, so that the new stats is
updated.
Ideally speaking based on 'Michal Kazior's' suggestion
we need to completely move to periodic update of all the stats making
the 'ping - pong' method obselete. This requires a bit of re-work and
some testing as well, also confirmation regarding backward comptability
for various firmware and chipsets. Hence allow periodic update only
for peer_stats.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Prerequisite patch to address checkpatch errors for the next patch
in this series, this function names are bit too long, make it short
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Replace the local variable 'burst_enable' with 'param'
for mapping and setting pdev paraemeters and with this patch
pretty easy to extend support for new parameters adhering to
linux kernel coding guidelines
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix naming of peer stats rssi_changed field in 10.2.4 to make it
more readable. As of now this field is not used, but necessary to
pull in fw_stats with appropriate length.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add support for parsing 'peer_rx_duration' as part
of 10.2.4 peer_stats. Also register PEER_STATS service
for parsing 'rx_duration' (and for any new fields to be added
as part of peer_stats). Have checks for backward compatibility with
older 10.2.4 firmware incase PEER_STATS service is not enabled
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
On multicore systems it was possible for the txrx
tasklet to keep on running for long periods of
time on a single CPU due to tx completion
processing. Another CPU could feed the running
tasklet for an indefinite amount of time.
The tasklet is now guaranteed to run a finite
amount of time and is limited by HTT CE Rx ring
depth.
This improves behavior when RPS is used on target
system and might improve TCP handling as well.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently mac80211 does not inform the driver of the session
block ack timeout when starting a rx aggregation session.
Drivers that manage the reorder buffer need to know this
parameter.
Seeing that there are now too many arguments for the
drv_ampdu_action() function, wrap them inside a structure.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use SMPS disabled as default because FW does not indicate
any support of SMPS.
This change will help STAs out that don’t support SMPS from
sticking on 1SS, since they don’t have method to change it
back to multiple chains.
This change also should not affect power consumption of STAs
supporting SMPS, because they are capable to switch the mode
to dynamic or static either at the end of frame sequence or
by using SMPS action frame.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For devices that does not support PCI power save, force wake up
API is used. So move powersave check inside force wakeup to reduce
one level indentation.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
commit 1aaf8efba0 ("ath10k: disable PCI PS for QCA988X
and QCA99X0") partially reverts pci soc powersave support added by
commit 77258d409c ("ath10k: enable pci soc powersaving"). While
reverting the change, pci wake up function is called after accessing
pci registers instead of prior to access. The assumption is that chip
is woken up before accessing its registers.Though this change does not
fix any known issues, this might help to avoid unknown or low power
platform specific issues.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Mesh Point requires peer security key install when running
in secured mode since it's a type of peer links, otherwise peer
link will be removed due to key install failure.
MFP feature set is required to run Mesh in secured mode and
QCA988X firmware, 10.2.4.70.14-2 and above, is the only one
supporting secured Mesh at this moment.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Coherent memory is more expensive to allocate (and constrained on some
architectures where it has to be pre-allocated). It is also completely
unnecessary, since the host has no reason to even access these allocated
memory spaces
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The default values of max_num_amsdu / max_num_amdpu is assigned a
default value as part of 'ath10k_core_init_firmware_features'
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When debugging firmware problems it's useful to check checksums of each
component. Add a debugfs interface to retrieve crc32 checksums:
# cat /sys/kernel/debug/ieee80211/phy0/ath10k/fw_checksums
firmware-N.bin cc3fb466
athwlan c0089f21
otp f3efeb4f
codeswap 00000000
board-N.bin bebc7c08
board bebc7c08
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Earlier we printed all the info messages after a successful device
initialisation and firmware boot, but that's problematic if something goes
wrong and there's no easy way to know what firmware version was used and so on.
Split the info messages into smaller pieces and print them as soon as we have
the info available.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA988X firmware starting from 10.2.4.70.12-2 has capability to support
Mesh Control Field Present bit in QoS field in native Wi-Fi mode.
Hence apply Mesh subtype according to the WMI service map.
Firmware will allows unicast, broadcast, multicast, and WDS frame
(FromDS = 1 and ToDS = 1) to be received via the interface, once Mesh
subtype is used.
The firmware and this patch together make native Wi-Fi mode comply to
IEEE802.11s Mesh frame in open mode, but the firmware doesn't yet
support secured Mesh mode.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA988X firmware starting from 10.2.4.70.12-2 supports new
vdev subtypes for proxy STA and Mesh, hence add them to be used
as needed.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Update WMI 10.x service map to sync with firmware 10.2.4.70.12-2
released on 11/11/2015 which is the latest QCA988X firmware as of
11/18/2015.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix write permission for few of the debugfs entries
which support write file operations as well.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
