This particular nasty presented itself while trying to register the
intelfb device (intel_fbdev.c). During the process of registering the device
the driver will disable the crtc via i9xx_crtc_disable. These will
also disable the panel using the generic mipi panel functions in
dsi_mod_vbt_generic.c. The stale MIPI generic data sequence pointers would
cause a crash within those functions. However, all of this is happening
while console_lock is held from do_register_framebuffer inside fbcon.c. Which
means that you got kernel log and just the device appearing to reboot/hang for
no apparent reason.
The fault started from the FB_EVENT_FB_REGISTERED event using the
fb_notifier_call_chain call in fbcon.c.
This regression has been introduced in
commit d3b542fcfc
Author: Shobhit Kumar <shobhit.kumar@intel.com>
Date: Mon Apr 14 11:00:34 2014 +0530
drm/i915: Add parsing support for new MIPI blocks in VBT
Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
[danvet: Add regression citation.]
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull DRM updates from Dave Airlie:
"Like all good pull reqs this ends with a revert, so it must mean we
tested it,
[ Ed. That's _one_ way of looking at it ]
This pull is missing nouveau, Ben has been stuck trying to track down
a very longstanding bug that revealed itself due to some other
changes. I've asked him to send you a direct pull request for nouveau
once he cleans things up. I'm away until Monday so don't want to
delay things, you can make a decision on that when he sends it, I have
my phone so I can ack things just not really merge much.
It has one trivial conflict with your tree in armada_drv.c, and also
the pull request contains some component changes that are already in
your tree, the base tree from Russell went via Greg's tree already,
but some stuff still shows up in here that doesn't when I merge my
tree into yours.
Otherwise all pretty standard graphics fare, one new driver and
changes all over the place.
New drivers:
- sti kms driver for STMicroelectronics chipsets stih416 and stih407.
core:
- lots of cleanups to the drm core
- DP MST helper code merged
- universal cursor planes.
- render nodes enabled by default
panel:
- better panel interfaces
- new panel support
- non-continuous cock advertising ability
ttm:
- shrinker fixes
i915:
- hopefully ditched UMS support
- runtime pm fixes
- psr tracking and locking - now enabled by default
- userptr fixes
- backlight brightness fixes
- MST support merged
- runtime PM for dpms
- primary planes locking fixes
- gen8 hw semaphore support
- fbc fixes
- runtime PM on SOix sleep state hw.
- mmio base page flipping
- lots of vlv/chv fixes.
- universal cursor planes
radeon:
- Hawaii fixes
- display scalar support for non-fixed mode displays
- new firmware format support
- dpm on more asics by default
- GPUVM improvements
- uncached and wc GTT buffers
- BOs > visible VRAM
exynos:
- i80 interface support
- module auto-loading
- ipp driver consolidated.
armada:
- irq handling in crtc layer only
- crtc renumbering
- add component support
- DT interaction changes.
tegra:
- load as module fixes
- eDP bpp and sync polarity fixed
- DSI non-continuous clock mode support
- better support for importing buffers from nouveau
msm:
- mdp5/adq8084 v1.3 hw enablement
- devicetree clk changse
- ifc6410 board working
tda998x:
- component support
- DT documentation update
vmwgfx:
- fix compat shader namespace"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (551 commits)
Revert "drm: drop redundant drm_file->is_master"
drm/panel: simple: Use devm_gpiod_get_optional()
drm/dsi: Replace upcasting macro by function
drm/panel: ld9040: Replace upcasting macro by function
drm/exynos: dp: Modify driver to support drm_panel
drm/exynos: Move DP setup into commit()
drm/panel: simple: Add AUO B133HTN01 panel support
drm/panel: simple: Support delays in panel functions
drm/panel: simple: Add proper definition for prepare and unprepare
drm/panel: s6e8aa0: Add proper definition for prepare and unprepare
drm/panel: ld9040: Add proper definition for prepare and unprepare
drm/tegra: Add support for panel prepare and unprepare routines
drm/exynos: dsi: Add support for panel prepare and unprepare routines
drm/exynos: dpi: Add support for panel prepare and unprepare routines
drm/panel: simple: Add dummy prepare and unprepare routines
drm/panel: s6e8aa0: Add dummy prepare and unprepare routines
drm/panel: ld9040: Add dummy prepare and unprepare routines
drm/panel: Provide convenience wrapper for .get_modes()
drm/panel: add .prepare() and .unprepare() functions
drm/panel: simple: Remove simple-panel compatible
...
This reverts commit 48ba813701.
Thanks to Chris:
"drm_file->is_master is not synomous with having drm_file->master ==
drm_file->minor->master. This is because drm_file->master is the same
for all drm_files of the same generation and so when there is a master,
every drm_file believes itself to be the master. Confusion ensues and
things go pear shaped when one file is closed and there is no master
anymore."
Conflicts:
drivers/gpu/drm/drm_drv.c
drivers/gpu/drm/drm_stub.c
We might be leaving the PGU Frequency (and thus vnn) high during the suspend.
Flusing the delayed work queue should take care of this.
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BDW has many other Display Engine interrupts and GT interrupts registers.
Collecting it properly on gpu_error_state.
On debugfs all was properly listed already but besides we were also listing old
DEIER and GTIER that doesn't exist on BDW anymore. This was causing
unclaimed register messages
v2: Fix small issues of first version and don't read DEIER regs when pipe's
power well is disabled
v3: bikeshed accepted: use enum pipe pipe instead of int i for pipe interection
v4: Ben notice previous version was checking for display_power_enabled without
using propper locks. Using _unlocked version isn't reliable and we cannot
get this registers when power well is off. So let's avoid getting all DE_IER
per pipe for now. If someone think this is an useful information it can be
added later.
v5: Ben: put back debugfs stuff that might be coverred by pm_get and use
gen >= 8 trying to predict future.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=81701
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: (v3) Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the actual head has progressed forward inside a batch (request),
don't accumulate hangcheck score.
As the hangcheck score in increased only by acthd jumping backwards,
the result is that we only declare an active batch as stuck if it is
trapped inside a loop. Or that the looping will dominate the batch
progression so that it overcomes the bonus that forward progress gives.
v2: Improved commit message (Chris Wilson)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: s/active_loop/active (loop)/ as requested by Chris.]
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Broadwell, any PIPE_CONTROL with the "State Cache Invalidate" bit set
must be preceded by a PIPE_CONTROL with the "CS Stall" bit set.
Documented on the BSpec 3D workarounds page.
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
[vsyrjala: add chv w/a note too]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We'll want to reuse this for a workaround.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Rmove now unused int.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mostly some cleanup all over the place. Pitch alignment limitations of
the display controller are now honored and job submission is 64-bit
safe.
The SOR output (used for eDP) properly configures sync signal polarities
according to the display mode rather than hard-coding them to some value
and the number of bits per color is now taken from the panel rather than
hard-coded to properly support 24-bit vs. 18-bit panels.
The DSI controller now properly supports non-continuous clock mode.
GEM objects can now have their flags and tiling mode modified via IOCTLs
to allow buffers imported from Nouveau to be properly displayed. Newer
generations of the Tegra display controller can also detile block linear
buffers at scan-out time.
Finally the driver now properly exports MODULE_DEVICE_TABLEs to allow it
to be automatically loaded when built as a module.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=qYgE
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-3.17-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v3.17-rc1
Mostly some cleanup all over the place. Pitch alignment limitations of
the display controller are now honored and job submission is 64-bit
safe.
The SOR output (used for eDP) properly configures sync signal polarities
according to the display mode rather than hard-coding them to some value
and the number of bits per color is now taken from the panel rather than
hard-coded to properly support 24-bit vs. 18-bit panels.
The DSI controller now properly supports non-continuous clock mode.
GEM objects can now have their flags and tiling mode modified via IOCTLs
to allow buffers imported from Nouveau to be properly displayed. Newer
generations of the Tegra display controller can also detile block linear
buffers at scan-out time.
Finally the driver now properly exports MODULE_DEVICE_TABLEs to allow it
to be automatically loaded when built as a module.
* tag 'drm/tegra/for-3.17-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: add MODULE_DEVICE_TABLEs
drm/tegra: dc - Reset controller on driver remove
drm/tegra: Properly align stride for framebuffers
drm/tegra: sor - Configure proper sync polarities
drm/tegra: sor - Use bits-per-color from panel
drm/tegra: Make job submission 64-bit safe
drm/tegra: Allow non-authenticated processes to create buffer objects
drm/tegra: Add SET/GET_FLAGS IOCTLs
drm/tegra: Add SET/GET_TILING IOCTLs
drm/tegra: Implement more tiling modes
drm/tegra: dsi - Handle non-continuous clock flag
drm/tegra: sor - missing unlock on error
Panels can now be more finely controlled via .prepare() and .unprepare()
callbacks in addition to .enable() and .disable(). New kerneldoc details
what they are supposed to do and when they should be called.
The simple panel driver gained support for a couple of new panels and it
is now possible to specify additional delays during power up and power
down sequences if panels require it.
DSI devices can now advertise that they support non-continuous clock
mode which will allow DSI host controllers to disable the high speed
clock after transmissions to save power.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vf7m
-----END PGP SIGNATURE-----
Merge tag 'drm/panel/for-3.17-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/panel: Changes for v3.17-rc1
Panels can now be more finely controlled via .prepare() and .unprepare()
callbacks in addition to .enable() and .disable(). New kerneldoc details
what they are supposed to do and when they should be called.
The simple panel driver gained support for a couple of new panels and it
is now possible to specify additional delays during power up and power
down sequences if panels require it.
DSI devices can now advertise that they support non-continuous clock
mode which will allow DSI host controllers to disable the high speed
clock after transmissions to save power.
* tag 'drm/panel/for-3.17-rc1' of git://anongit.freedesktop.org/tegra/linux: (30 commits)
drm/panel: simple: Use devm_gpiod_get_optional()
drm/dsi: Replace upcasting macro by function
drm/panel: ld9040: Replace upcasting macro by function
drm/exynos: dp: Modify driver to support drm_panel
drm/exynos: Move DP setup into commit()
drm/panel: simple: Add AUO B133HTN01 panel support
drm/panel: simple: Support delays in panel functions
drm/panel: simple: Add proper definition for prepare and unprepare
drm/panel: s6e8aa0: Add proper definition for prepare and unprepare
drm/panel: ld9040: Add proper definition for prepare and unprepare
drm/tegra: Add support for panel prepare and unprepare routines
drm/exynos: dsi: Add support for panel prepare and unprepare routines
drm/exynos: dpi: Add support for panel prepare and unprepare routines
drm/panel: simple: Add dummy prepare and unprepare routines
drm/panel: s6e8aa0: Add dummy prepare and unprepare routines
drm/panel: ld9040: Add dummy prepare and unprepare routines
drm/panel: Provide convenience wrapper for .get_modes()
drm/panel: add .prepare() and .unprepare() functions
drm/panel: simple: Remove simple-panel compatible
drm/panel: simple: Add Innolux N116BGE panel support
...
The DDL registers can hold 7bit numbers. Make the most of those seven
bits by adjusting the threshold where we switch between the 64 vs. 32
precision multipliers.
Also we compute 'entries' to make the decision about precision, and then
we recompute the same value to calculate the actual drain latency. Just
use the already calculate 'entries' there.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GTIER and DEIER doesn't have same interface on HSW so this "or" operation
makes the information provided useless.
v2: since we have gtier variable already let's split for everybody
and avoid the strange | op.
Also avoid overriding the value that was set for vlv. In this case I
believe that we should reorganize the whole function, but I'll respect
the comment that ask to not touch the order and let this organization
work to be done later.
v3: moving VLV check to the right place.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Users often can't do anything about this since their vendors stopped
providing BIOS updates. Also we seem to be able to hack around it
with increased latency values, and thus far the only reports have
been for screens with really high resolutions. So tune it down to a
level where only developers can see it.
Also drop some of the end-user fluff.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Power users spot this and then get adventurous and try to adjust
module driver options. Nothing good ever came out of that, so
hide it better.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since I've reworked psr support to no longer require x-tiling we don't
check any state protected by the Giant GEM Lock. So drop that check.
Also boo for lockdep_assert_held for not yelling when lockdep is
disabled.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reported-by: Paulo Zanoni <przanoni@gmail.com>
Acked-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix signal_offset when recording semaphore state on BDW.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like during booting the BIOS can leave the VDD bit enabled after
system resume. So apply the same state sanitization there too. This
fixes a problem where after resume the port power domain refcount gets
unbalanced.
v2:
- unchanged
v3:
- call edp sanitizing from the encoder reset handler (Daniel)
Reported-and-tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check in vlv_crtc_clock_get if DPLL is enabled before calling dpio read.
It will not be enabled for DSI and avoid dpio read WARN dumps.
Absence of ->get_config was causing other WARN dumps as well. Update
dpll_hw_state as well correctly
v2: Address review comments by Daniel
- Check if DPLL is enabled rather than checking pipe output type
- set adjusted_mode->flags to 0 in compute_config rather than using
pipe_config->quirks
- Add helper function in intel_dsi_pll.c and use that in intel_dsi.c
- updated dpll_hw_state correctly
- Updated commit message and title
v3: Address review comments by Imre
- Proper masking of P1, M1 fields while computing divisors
- assert in case of bpp mismatch
- guard for divide by 0 while computing pclk
- Use ARRAY_SIZE instead of direct calculation
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be needed by an upcoming patch too that needs to sanitize the
VDD state during resume. The additional async disabling is only needed
for the resume path, here it doesn't make a difference since we enable
VDD right after the sanitize call.
v2:
- don't set intel_dp ptr for non-eDP encoders (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ensure that the DSI packets for a particular sequence are completely
sent before going ahead in the enabling or disabling of the panel
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Gcc warns that addr might be used uninitialized. It may not, but I see
why gcc gets confused.
Additionally, hiding code with side-effects inside WARN_ON() argument
seems uncool, so I moved it outside.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
[danvet: Add obligatory /* shuts up gcc */ comment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the new devm_gpiod_get_optional() to simplify the probe code.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Merge incoming from Andrew Morton:
- Various misc things.
- arch/sh updates.
- Part of ocfs2. Review is slow.
- Slab updates.
- Most of -mm.
- printk updates.
- lib/ updates.
- checkpatch updates.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (226 commits)
checkpatch: update $declaration_macros, add uninitialized_var
checkpatch: warn on missing spaces in broken up quoted
checkpatch: fix false positives for --strict "space after cast" test
checkpatch: fix false positive MISSING_BREAK warnings with --file
checkpatch: add test for native c90 types in unusual order
checkpatch: add signed generic types
checkpatch: add short int to c variable types
checkpatch: add for_each tests to indentation and brace tests
checkpatch: fix brace style misuses of else and while
checkpatch: add --fix option for a couple OPEN_BRACE misuses
checkpatch: use the correct indentation for which()
checkpatch: add fix_insert_line and fix_delete_line helpers
checkpatch: add ability to insert and delete lines to patch/file
checkpatch: add an index variable for fixed lines
checkpatch: warn on break after goto or return with same tab indentation
checkpatch: emit a warning on file add/move/delete
checkpatch: add test for commit id formatting style in commit log
checkpatch: emit fewer kmalloc_array/kcalloc conversion warnings
checkpatch: improve "no space after cast" test
checkpatch: allow multiple const * types
...
Pull trivial tree changes from Jiri Kosina:
"Summer edition of trivial tree updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: fix two typos in watchdog-api.txt
irq-gic: remove file name from heading comment
MAINTAINERS: Add miscdevice.h to file list for char/misc drivers.
scsi: mvsas: mv_sas.c: Fix for possible null pointer dereference
doc: replace "practise" with "practice" in Documentation
befs: remove check for CONFIG_BEFS_RW
scsi: doc: fix 'SCSI_NCR_SETUP_MASTER_PARITY'
drivers/usb/phy/phy.c: remove a leading space
mfd: fix comment
cpuidle: fix comment
doc: hpfall.c: fix missing null-terminate after strncpy call
usb: doc: hotplug.txt code typos
kbuild: fix comment in Makefile.modinst
SH: add proper prompt to SH_MAGIC_PANEL_R2_VERSION
ARM: msm: Remove MSM_SCM
crypto: Remove MPILIB_EXTRA
doc: CN: remove dead link, kerneltrap.org no longer works
media: update reference, kerneltrap.org no longer works
hexagon: update reference, kerneltrap.org no longer works
doc: LSM: update reference, kerneltrap.org no longer works
...
All other add functions for lists have the new item as first argument
and the position where it is added as second argument. This was changed
for no good reason in this function and makes using it unnecessary
confusing.
The name was changed to hlist_add_behind() to cause unconverted code to
generate a compile error instead of using the wrong parameter order.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Ken Helias <kenhelias@firemail.de>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> [intel driver bits]
Cc: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drm_vblank_cleanup() would operate on non-existent dev->vblank
data structure, as failure to allocate that data structure is
what triggers the error path in the first place.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During vblank disable the code tries to guess based on the
timestamps whether we just missed one vblank or not. And if so
it increments the counter. However it forgets to store the new
timestamp to the approriate slot in our timestamp ring buffer.
So anyone querying the timestamp for the resulting sequence
number would get a stale timestamp. Fix it up by storing the
new timestamp.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that drm_update_vblank_count() can be called even when we're not
about to enable the vblank interrupts we shouldn't print debug messages
stating otherwise.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
update_scanline_offset() in intel_sanitize_crtc() was supposed to
be called only for active crtcs. But due to some underrun patches it
now gets updated for all crtcs on gmch platforms.
Move the update_scanline_offset() to the very beginning of
intel_sanitize_crtc() where we update the vblank state. This seems like
a better place anyway since the scanline offset ought to be up to date
before we might need to consult it. So before any vblanky stuff happens.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the user is interested in getting accurate vblank sequence
numbers all the time they may disable the vblank disable timer
entirely. In that case it seems appropriate to kick start the
vblank interrupts already from drm_vblank_on().
v2: Adapt to the drm_vblank_offdelay ==0 vs <0 changes
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the vblank races are plugged, we can opt out of using
the vblank disable timer and just let vblank interrupts get
disabled immediately when the last reference is dropped.
Gen2 is the exception since it has no hardware frame counter.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a flag to drm_device which will cause the vblank code to bypass the
disable timer and always disable the vblank interrupt immediately when
the last reference is dropped.
v2: Add some notes about the flag to the kernel doc
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make drm_vblank_put() disable the vblank interrupt immediately when the
refcount drops to zero and drm_vblank_offdelay<0.
v2: Preserve the current drm_vblank_offdelay==0 'never disable' behaviur
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently it's possible that the following will happen:
1. drm_wait_vblank() calls drm_vblank_get()
2. drm_vblank_off() gets called
3. drm_wait_vblank() calls drm_queue_vblank_event() which
adds the event to the queue event though vblank interrupts
are currently disabled (and may not be re-enabled ever again).
To fix the problem, add another vblank->enabled check into
drm_queue_vblank_event().
drm_vblank_off() holds event_lock around the vblank disable,
so no further locking needs to be added to drm_queue_vblank_event().
vblank disable from another source is not possible since
drm_wait_vblank() already holds a vblank reference.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently both drm_irq.c and several drivers call drm_vblank_put()
while holding event_lock. Now that drm_vblank_put() can disable the
vblank interrupt directly it may need to grab vbl_lock and
vblank_time_lock. That causes deadlocks since we take the locks
in the opposite order in two places in drm_irq.c. So let's make
sure the locking order is always event_lock->vbl_lock->vblank_time_lock.
In drm_vblank_off() pull up event_lock from underneath vbl_lock. Hold
the event_lock across the whole operation to make sure we only send
out the events that were on the queue when we disabled the interrupt,
and not ones that got added just after (assuming drm_vblank_on() already
managed to get called somewhere between).
To sort the other deadlock pull the event_lock out from
drm_handle_vblank_events() into drm_handle_vblank() to be taken outside
vblank_time_lock. Add the appropriate assert_spin_locked() to
drm_handle_vblank_events().
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When drm_vblank_on() is called the hardware vblank counter may have
been reset, so we can't trust that the old values sampled prior to
drm_vblank_off() have anything to do with the new values.
So update the .last count in drm_vblank_on() to make the first
drm_vblank_enable() consider that as the reference point. This
will correct the user space visible counter to account for the
time between drm_vblank_on() and the first drm_vblank_enable()
calls.
For extra safety subtract one from the .last count in drm_vblank_on()
to make sure that user space will never see the same counter value
before and after modeset.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the vblank irq has already been disabled (via the disable timer) when
we call drm_vblank_off() sample the counter and timestamp one last time.
This will make the sure that the user space visible counter will account
for time between vblank irq disable and drm_vblank_off().
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move drm_update_vblank_count() to avoid forward a declaration.
No functional change.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Clearing the timestamps causes us to send zeroed timestamps to userspace
if they get sent out in response to the drm_vblank_off(). It's better
to send the very latest timestamp and count instead.
Testcase: igt/kms_flip/modeset-vs-vblank-race
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Drop the drm_vblank_off() (Daniel)
Use drm_crtc_vblank_{get,put}()
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make sure drm_vblank_get() never succeeds when called between
drm_vblank_off() and drm_vblank_on(). Borrow a trick from the
old drm_vblank_{pre,post}_modeset() functions and just bump
the refcount in drm_vblank_off() and drop it in drm_vblank_on().
When drm_vblank_get() encounters a >0 refcount and the vblank
interrupt is already disabled it will simply return -EINVAL.
Hopefully the use of inmodeset won't conflict badly with
drm_vblank_{pre,post}_modeset().
For i915 there's a window between drm_vblank_off() and marking the
crtc as inactive where the current code still allows drm_vblank_get().
v2: Describe what drm_vblank_get() does to explain how
a simple refcount bump manages to fix things (Daniel)
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After spending slightly more time than I'd care to admit debugging the
various and presumably spectacular way things fail when you pass too low
a value to drm_vblank_init() (thanks console-lock for not letting me see
the carnage!), I decided it might be a good idea to add some sanity
checking.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add drm_panel controls to support powerup/down of the
eDP panel, if one is present at the sink side.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add commit callback for exynos_dp, and move the DP link training,
video configuration code from the hotplug handler into commit().
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The AUO B133HTN01 is a 13.6" FHD TFT LCD panel connecting to an eDP
interface and with an integrated LED backlight unit.
This panel is used on the Samsung Chromebook 2 (XE503C32).
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For most of the panels, we need to provide delays during various stages
of panel power up and power down. Add a structure to hold those delay
values and use them in corresponding functions.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move out code from enable and disable routines to prepare
and unprepare routines, so that functionality is properly
distributed across all the panel functions.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
