When connected to HDMI sources, some DVI monitors de-assert their HPD
signal and TDMS loads for one seconds every four seconds when there is
no signal present on the connection.
Unfortunately, this behaviour is indistinguishable from a proper HDMI
setup with an AV receiver in the path to the display: the HDMI spec
requires us to detect HPD deassertions as short as 100ms, which indicate
that the EDID has changed.
Since it is possible to connect a DVI monitor to an AV receiver and then
to a HDMI source, merely working around this by detecting the lack of
HDMI vendor block in the EDID is insufficient - the AV receiver is at
liberty to modify the EDID as it sees fit, and it will place its own
parameters into the EDID including the HDMI vendor block.
DRM has support for forcing the state of a connector, which we should
implement to allow us to work around these broken DVI monitors - we can
tell DRM to force the connection state to indicate that there is always
a device connected to work around this problem. Although this requires
manual configuration, it is better than nothing at all.
When a forced connection state has been set, there is no point handling
our RXSENSE interrupts, so disable them in this circumstance.
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for interlaced video modes to the dw_hdmi bridge. This
mainly involves halving the vertical parameters to be programmed into
the bridge registers, and setting the interlace_allowed connector flag.
This brings working 1080i support. However, 480i and 576i fail to
work due to the lack of proper pixel repetition support, which is not
trivial to add due to the tabular PLL parameterisation. Hence, we
filter out these modes in our mode_valid() method.
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These have not been tested very extensively and generally
seem to be problematic. Mark them as experimental for now.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=92270
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Make sure we are not the root device before attempting to
read the pcie bridge registers to check the pcie gen speeed.
Fixes a crash when the device is passed through to a VM.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Whilst discussing possible ways to trigger an invalidate_range on a
userptr with an aliased GGTT mmapping (and so cause a struct_mutex
deadlock), the conclusion is that we can, and we must, prevent any
possible deadlock by avoiding taking the mutex at all during
invalidate_range. This has numerous advantages all of which stem from
avoid the sleeping function from inside the unknown context. In
particular, it simplifies the invalidate_range because we no longer
have to juggle the spinlock/mutex and can just hold the spinlock
for the entire walk. To compensate, we have to make get_pages a bit more
complicated in order to serialise with a pending cancel_userptr worker.
As we hold the struct_mutex, we have no choice but to return EAGAIN and
hope that the worker is then flushed before we retry after reacquiring
the struct_mutex.
The important caveat is that the invalidate_range itself is no longer
synchronous. There exists a small but definite period in time in which
the old PTE's page remain accessible via the GPU. Note however that the
physical pages themselves are not invalidated by the mmu_notifier, just
the CPU view of the address space. The impact should be limited to a
delay in pages being flushed, rather than a possibility of writing to
the wrong pages. The only race condition that this worsens is remapping
an userptr active on the GPU where fresh work may still reference the
old pages due to struct_mutex contention. Given that userspace is racing
with the GPU, it is fair to say that the results are undefined.
v2: Only queue (and importantly only take one refcnt) the worker once.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Michał Winiarski found a really evil way to trigger a struct_mutex
deadlock with userptr. He found that if he allocated a userptr bo and
then GTT mmaped another bo, or even itself, at the same address as the
userptr using MAP_FIXED, he could then cause a deadlock any time we then
had to invalidate the GTT mmappings (so at will). Tvrtko then found by
repeatedly allocating GTT mmappings he could alias with an old userptr
mmap and also trigger the deadlock.
To counter act the deadlock, we make the observation that we only need
to take the struct_mutex if the object has any pages to revoke, and that
before userspace can alias with the userptr address space, it must have
invalidated the userptr->pages. Thus if we can check for those pages
outside of the struct_mutex, we can avoid the deadlock. To do so we
introduce a separate flag for userptr objects that we can inspect from
the mmu-notifier underneath its spinlock.
The patch makes one eye-catching change. That is the removal serial=0
after detecting a to-be-freed object inside the invalidate walker. I
felt setting serial=0 was a questionable pessimisation: it denies us the
chance to reuse the current iterator for the next loop (before it is
freed) and being explicit makes the reader question the validity of the
locking (since the object-free race could occur elsewhere). The
serialisation of the iterator is through the spinlock, if the object is
freed before the next loop then the notifier.serial will be incremented
and we start the walk from the beginning as we detect the invalid cache.
To try and tame the error paths and interactions with the userptr->active
flag, we have to do a fair amount of rearranging of get_pages_userptr().
v2: Grammar fixes
v3: Reorder set-active so that it is only set when obj->pages is set
(and so needs cancellation). Only the order of setting obj->pages and
the active-flag is crucial. Calling gup after invalidate-range begin
means the userptr sees the new set of backing storage (and so will not
need to invalidate its new pages), but we have to be careful not to set
the active-flag prior to successfully establishing obj->pages.
v4: Take the active->flag early so we know in the mmu-notifier when we
have to cancel a pending gup-worker.
v5: Rearrange the error path so that is not so convoluted
v6: Set pinned to 0 when negative before calling release_pages()
Reported-by: Michał Winiarski <michal.winiarski@intel.com>
Testcase: igt/gem_userptr_blits/map-fixed*
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The userptr worker allows for a slight race condition where upon there
may two or more threads calling get_user_pages for the same object. When
we have the array of pages, then we serialise the update of the object.
However, the worker should only overwrite the obj->userptr.work pointer
if and only if it is the active one. Currently we clear it for a
secondary worker with the effect that we may rarely force a second
lookup.
v2: Rebase and rename a variable to avoid 80cols
v3: Mention v2
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We tried to fix this in commit fdc454c148 ("drm/i915: Prevent out of
range pt in gen6_for_each_pde").
But the static analyzer still complains that, just before we break due
to "iter < I915_PDES", we do "pt = (pd)->page_table[iter]" with an
iter value that is bigger than I915_PDES. Of course, this isn't really
a problem since no one uses pt outside the macro. Still, every single
new usage of the macro will create a new issue for us to mark as a
false positive.
Also, Paulo re-started the discussion a while ago [1], but didn't end up
implemented.
In order to "solve" this "problem", this patch takes the ideas from
Chris and Dave, but that check would change the desired behavior of the
code, because the object (for example pdp->page_directory[iter]) can be
null during init/alloc, and C would take this as false, breaking the for
loop immediately.
This has been already verified with "static analysis tools".
[1]http://lists.freedesktop.org/archives/intel-gfx/2015-June/068548.html
v2: Make it a single statement, while preventing the common subexpression
elimination (Chris)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prevent leaking VMAs and PPGTT VMs when objects are imported
via flink.
Scenario is that any VMAs created by the importer will be left
dangling after the importer exits, or destroys the PPGTT context
with which they are associated.
This is caused by object destruction not running when the
importer closes the buffer object handle due the reference held
by the exporter. This also leaks the VM since the VMA has a
reference on it.
In practice these leaks can be observed by stopping and starting
the X server on a kernel with fbcon compiled in. Every time
X server exits another VMA will be leaked against the fbcon's
frame buffer object.
Also on systems where flink buffer sharing is used extensively,
like Android, this leak has even more serious consequences.
This version is takes a general approach from the earlier work
by Rafael Barbalho (drm/i915: Clean-up PPGTT on context
destruction) and tries to incorporate the subsequent discussion
between Chris Wilson and Daniel Vetter.
v2:
Removed immediate cleanup on object retire - it was causing a
recursive VMA unbind via i915_gem_object_wait_rendering. And
it is in fact not even needed since by definition context
cleanup worker runs only after the last context reference has
been dropped, hence all VMAs against the VM belonging to the
context are already on the inactive list.
v3:
Previous version could deadlock since VMA unbind waits on any
rendering on an object to complete. Objects can be busy in a
different VM which would mean that the cleanup loop would do
the wait with the struct mutex held.
This is an even simpler approach where we just unbind VMAs
without waiting since we know all VMAs belonging to this VM
are idle, and there is nothing in flight, at the point
context destructor runs.
v4:
Double underscore prefix for __915_vma_unbind_no_wait and a
commit message typo fix. (Michel Thierry)
Note that this is just a partial/interim fix since we have a bit a
fundamental issue with cleaning up, e.g.
https://bugs.freedesktop.org/show_bug.cgi?id=87729
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Testcase: igt/gem_ppgtt.c/flink-and-exit-vma-leak
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rafael Barbalho <rafael.barbalho@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
[danvet: Add a note that this isn't everything.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This continues the pattern started in commit cc1ef118fc ("drm/irq:
Make pipe unsigned and name consistent"). This is applied to the public
APIs and driver callbacks, so pretty much all drivers need to be updated
to match the new prototypes.
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Jianwei Wang <jianwei.wang.chn@gmail.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The link training functions had confusing names. The start function
actually does the clock recovery phase of the link training, and the
complete function does the channel equalization. So call them that
instead. Also, every call to intel_dp_start_link_train() was followed
by a call to intel_dp_complete_link_train(), so add a new start
function that calls clock_recory and channel_equalization.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds a separate probe function for HDMI
EDID read over DDC channel. This function has been
registered as a .hot_plug handler for HDMI encoder.
The current implementation of hdmi_detect()
function re-sets the cached HDMI edid (in connector->detect_edid) in
every detect call.This function gets called many times, sometimes
directly from userspace probes, forcing drivers to read EDID every
detect function call.This causes several problems like:
1. Race conditions in multiple hot_plug / unplug cases, between
interrupts bottom halves and userspace detections.
2. Many Un-necessary EDID reads for single hotplug/unplug
3. HDMI complaince failures which expects only one EDID read per hotplug
This function will be serving the purpose of really reading the EDID
by really probing the DDC channel, and updating the cached EDID.
The plan is to:
1. i915 IRQ handler bottom half function already calls
intel_encoder->hotplug() function. Adding This probe function which
will read the EDID only in case of a hotplug / unplug.
2. During init_connector this probe will be called to read the edid
3. Reuse the cached EDID in hdmi_detect() function.
The "< gen7" check is there because this was tested only for >=gen7
platforms. For older platforms the hotplug/reading edid path remains same.
v2: Calling set_edid instead of hdmi_probe during init.
Also, for platforms having DDI, intel_encoder for DP and HDMI is same
(taken from intel_dig_port), so for DP also, hot_plug function gets called
which is not intended here. So, check for HDMI in intel_hdmi_probe
Rely on HPD for updating edid only for platforms gen > 8 and also for VLV.
v3: Dropping the gen < 8 || !VLV check. Now all platforms should rely on
hotplug or init for updating the edid.(Daniel)
Also, calling hdmi_probe in init instead of set_edid
v4: Renaming intel_hdmi_probe to intel_hdmi_hot_plug.
Also calling this hotplug handler from intel_hpd_init to take care of init
resume scenarios.
v5: Moved the call to encoder hotplug during init to separate patch(Daniel)
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
[danvet: Mark intel_hdmi_hot_plug as static.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is required to support glDispatchComputeIndirect for gen7.
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When using RC6 timeout mode, the timeout value
should be written to GEN6_RC6_THRESHOLD.
v2: Updated commit message. (Tom)
v3: Rebase over whitespace differences. (Daniel)
Cc: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add host2guc interface to notify GuC power state changes when
enter or resume from power saving state.
v3: Move intel_guc_suspend to i915_drm_suspend for consistency.
v2: Add GuC suspend/resume to runtime suspend/resume too
v1: Change to a more flexible way when fill host to GuC scratch
data in order to remove hard coding.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The BIOS can leave the CHV display PHY in some odd state where
some of the LDOs/lanes won't power down fully when unused. This
will trigger a host of asserts that were added in:
30142273a3 drm/i915: Add CHV PHY LDO power sanity checks
6669e39f95 drm/i915: Add some CHV DPIO lane power state asserts
To avoid that, skip the asserts until the PHY power well has been
disabled at least once. That will fully reset the PHY, and once
brought back up, the dynamic power down features will work correctly.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The docs are unclear as usual, so it's not clear whether LRC should be
bypassed, performed normally or GRC code should be used as the LRC code.
Some old docs stated that LRC bypass ought to be used, more recent ones
no longer say that. Some docs indicated that we could use GRC as the LRC
code on CHV, but the BIOS doesn't do that, so let's not do it either.
Besides to enable LRC bypass properly, I believe we should set the bit
already before deasserting cmnreset.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For all the encoders, call the hot_plug if it is registered.
This is required for connected boot and resume cases to generate
fake hpd resulting in reading of edid.
Removing the initial sdvo hot_plug call too so that it will be called
just once from this loop.
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
restore the fbdev state if a drm app like X is killed.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
restore the fbdev state if a drm app like X is killed.
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Avoid magic numbers and use the introduced defines.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to call intel_runtime_pm_put() and mutex_unlock() before
returning.
Fixes: 7cb5dff8d5 ('drm/i915: fix task reference leak in i915_debugfs.c')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They were added relatively early in the driver init process
which meant that in some cases the driver was not finished
initializing before external tools tried to use them which
could result in a crash depending on the timing.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
They were added relatively early in the driver init process
which meant that in some cases the driver was not finished
initializing before external tools tried to use them which
could result in a crash depending on the timing.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
There doesn't seem to be any need to have 'ib' volatile, the code is
not even consistent with it and some places already miss it. As it is
now it's just making gcc produce worse code. If there are special
requirements for that memory, then proper primitives like memory
barriers or accessor functions should be used, but it doesn't look
like that is needed here.
While at it, change the type to match the one in radeon_ib structure.
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
After this patch the register check loop does the same thing as before,
except that now gcc does better job optimizing it: it now sees that
end_reg was already checked against PACKET3_SET_CONTEXT_REG_END and can
optimize REG_SAFE_BM_SIZE comparison out of evergreen_is_safe_reg()
as (PACKET3_SET_CONTEXT_REG_END >> 7) < REG_SAFE_BM_SIZE.
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
evergreen_cs_check_reg() is a large function and gcc doesn't want to
inline it. It has a quick check for reg_safe_bm[] to see if register
needs special handling, which often results in early exit. However
because the function is large, it has a long prologue/epilogue to
save/restore all the callee-save registers which according to perf is
taking significant amount of time. To avoid this, we can reuse
evergreen_is_safe_reg() to do the early check directly in register loop.
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To avoid having to distinguish between CAYMAN or older on every register
check, place a pointer in evergreen_cs_track and use it unconditionally.
Also make use of the fact that both reg_safe_bm[] arrays are of the same
length to remove another CAYMAN check.
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently everyone and their dog has their own favourite spelling
for vga_switcheroo. This makes it hard to grep dmesg for log entries
relating to vga_switcheroo. It also makes it hard to find related
source files in the tree.
vga_switcheroo.c uses pr_fmt "vga_switcheroo". Use that everywhere.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently everyone and their dog has their own favourite spelling
for vga_switcheroo. This makes it hard to grep dmesg for log entries
relating to vga_switcheroo. It also makes it hard to find related
source files in the tree.
vga_switcheroo.c uses pr_fmt "vga_switcheroo". Use that everywhere.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Latest VBT mentions which set of registers will be used for BLC,
as controller number field. Making use of this field in BXT
BLC implementation. Also, the registers are used in case control
pin indicates display DDI. Adding a check for this.
According to Bspec, BLC_PWM_*_2 uses the display utility pin for output.
To use backlight 2, enable the utility pin with mode = PWM
v2: Jani's review comments
addressed
- Add a prefix _ to BXT BLC registers definitions.
- Add "bxt only" comment for u8 controller
- Remove control_pin check for DDI controller
- Check for valid controller values
- Set pipe bits in UTIL_PIN_CTL
- Enable/Disable UTIL_PIN_CTL in enable/disable_backlight()
- If BLC 2 is used, read active_low_pwm from UTIL_PIN polarity
Satheesh's review comment addressed
- If UTIL PIN is already enabled, BIOS would have programmed it. No
need to disable and enable again.
v3: Jani's review comments
- add UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK
- Disable UTIL_PIN if controller 1 is used
- Mask out UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK before enabling
UTIL_PIN
- check valid controller value in intel_bios.c
- add backlight.util_pin_active_low
- disable util pin before enabling
v4: Change for BXT-PO branch:
Stubbed unwanted definition which was existing before
because of DC6 patch.
UTIL_PIN_MODE_PWM (0x1b << 24)
v2: Fixed Jani's review comment.
v3: Split the backight PWM frequency programming into separate patch,
in cases BIOS doesn't initializes it.
v4: Starting afresh and not modifying existing state for backlight, as
per Jani's recommendation.
v5: Fixed Jani's review comment wrt util pin enable
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BXT's DSI PLL is different from that of VLV. So this patch
adds a new function to get the current DSI pixel clock based
on the PLL divider ratio and lane count.
This function is required for intel_dsi_get_config() function.
v2: Fixed Jani's review comments.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pick appropriate port control register (BXT or VLV), based on device.
Get the current hw state wrt Mipi port.
v2: Rebased on latest drm nightly branch.
v3: Removed the GET_DSI_PORT_CTRL Macro for consistency with earlier
implementations as per Jani's suggestion.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch contains changes to support DSI disble sequence in BXT.
The changes are:
1. BXT specific changes in clear_device_ready function.
2. BXT specific changes in DSI disable and post-disable functions.
3. Add a new function to reset BXT Dphy clock and dividers
(bxt_dsi_reset_clocks).
4. Moved some part of the vlv clock reset code, in a new function
(vlv_dsi_reset_clocks) maintaining the exact same sequence.
5. Wrapper function to call corresponding reset clock function.
v2: Fixed Jani's review comments.
v3: Removed the GET_DSI_PORT_CTRL Macro for consistency with earlier
implementations as per Jani's suggestion.
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BXT DSI clocks are different than previous platforms. So adding a
new function to program following clocks and dividers:
1. Program variable divider to generate input to Tx clock divider
(Output value must be < 39.5Mhz)
2. Select divide by 2 option to get < 20Mhz for Tx clock
3. Program 8by3 divider to generate Rx clock
v2: Fixed Jani's review comments. Adjusted the Macro definition as
per convention. Simplified the logic for bit definitions for
MIPI PORT A and PORT C in same registers.
v3: Refactored the macros for TX, RX Escape and DPHY clocks as per
Jani's suggestion.
v4: Addressed Jani's review comments.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch contains following changes:
1. MIPI device ready changes to support dsi_pre_enable. Changes
are specific to BXT device ready sequence. Added check for
ULPS mode(No effects on VLV).
2. Changes in dsi_enable to pick BXT port control register.
3. Changes in dsi_pre_enable to restrict DPIO programming for VLV
v2: Fixed Jani's review comments. Removed the changes in VLV/CHV
code. Fixed the macros to get proper port offsets.
v3: Rebased on latest drm-nightly branch. Fixed Jani's review comments.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SKL and BXT qualifies the HAS_DDI() check, and hence haswell
modeset functions are re-used for modeset sequence. But DDI
interface doesn't include support for DSI.
This patch adds:
1. cases for DSI encoder, in those modeset functions and allows
a CRTC modeset
2. Adds call to pre_pll enabled from CRTC modeset function. Nothing
needs to be done as such in CRTC for DSI encoder, as PLL, clock
and and transcoder programming will be taken care in encoder's
pre_enable and pre_pll_enable function.
v2: Fixed Jani's review comments. Added INVALID_PORT for non DDI
encoder like DSI for platforms having HAS_DDI as true.
v3: Rebased on latest drm-nightly branch. Added a WARN_ON for invalid
encoder.
v4: WARN_ON for invalid encoder is refactored as per Jani's suggestion.
Fixed the sequence for pre_pll_enable.
v5: Protected DDI code paths in case of DSI encoder calls.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This register was added on GEN4, by the name INSTDONE_1 whereas the GEN6
specification calls it INSTDONE_2. Keep the original name with a
platform prefix to make it clearer which INSTDONE register instance this
is. Also add a comment about the SNB alternative name.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have a bunch of INSTDONE registers for different platforms and
purposes and it's not immediately clear which instance they are just by
looking at the register name. This one was added on GEN2, where it was
the only INSTDONE register, so mark it as such.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We use 3 different names to refer to the same render ring INSTDONE
register. This can be confusing when comparing two parts of the code
accessing the register via different names. Although the GEN4 version's
layout is different, we treat it the same way as the GEN7+ version, in
that we simply read it out during error capture. So remove the
duplicates and leave a comment about the GEN4 difference.
Note that there is also a GEN2 version of this register, but that's on a
different address so not handled in this patch.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- initialize backlight from VBT as fallback (Jani)
- hpd A support from Ville
- various atomic polish all over (mostly from Maarten)
- first parts of virtualize gpu guest support on bdw from
Zhiyuan Lv
- GuC fixes from Alex
- polish for the chv clocks code (Ville)
- various things all over, as usual
* tag 'drm-intel-next-2015-09-11' of git://anongit.freedesktop.org/drm-intel: (145 commits)
drm/i915: Update DRIVER_DATE to 20150911
drm/i915: Remove one very outdated comment
drm/i915: Use crtc->state for duplication.
drm/i915: Do not handle a null plane state.
drm/i915: Remove legacy plane updates for cursor and sprite planes.
drm/i915: Use atomic state when changing cursor visibility.
drm/i915: Use the atomic state in intel_update_primary_planes.
drm/i915: Use the plane state in intel_crtc_info.
drm/i915: Use atomic plane state in the primary plane update.
drm/i915: add attached connector to hdmi container
drm/i915: don't hard code vlv backlight frequency if unset
drm/i915: initialize backlight max from VBT
drm/i915: use pch backlight override on hsw too
drm/i915/bxt: Clean up bxt_init_clock_gating
drm/i915: Fix cmdparser STORE/LOAD command descriptors
drm/i915: Dump pfit state as hex
drm/i915: access the PP_ON_DELAYS/PP_OFF_DELAYS regs only pre GEN5
drm/i915: access the PP_CONTROL reg only pre GEN5
drm/i915: Refactor common ringbuffer allocation code
drm/i915: use the yesno helper for logging
...
In order to cache the EDID properly for tiled displays, we
need to retrieve it before we register the connector with
userspace, otherwise userspace can call get resources
and try and get the edid before we've even cached it.
This fixes some problems when hotplugging mst monitors,
with X/mutter running. As mutter seems to get 0 modes
for one of the monitors in the tile.
v2: fix warning in radeon
handle tile setting in cached path rather than
get edid path.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Update the state before sending the msg to close it.
v2: reset value if return indicates we haven't send the msg.
v3: just clean the code up.
Pointed out by Adam J Richter on
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91481
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
output ports should always have a connector, unless
in the rare case connector allocation fails in the
driver.
In this case we only need to teardown the pdt,
and free the struct, and there is no need to
send a hotplug msg.
In the case were we add the port to the destroy
list we need to send a hotplug if we destroy
any connectors, so userspace knows to reprobe
stuff.
this patch also handles port->connector allocation
failing which should be a rare event, but makes
the code consistent.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is unnecessary and it makes it easier to see what is needed
from port.
also add blank line to make things nicer.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
