This patch (as1521b) fixes the interaction between usb-storage's
scanning thread and the freezer. The current implementation has a
race: If the device is unplugged shortly after being plugged in and
just as a system sleep begins, the scanning thread may get frozen
before the khubd task. Khubd won't be able to freeze until the
disconnect processing is complete, and the disconnect processing can't
proceed until the scanning thread finishes, so the sleep transition
will fail.
The implementation in the 3.2 kernel suffers from an additional
problem. There the scanning thread calls set_freezable_with_signal(),
and the signals sent by the freezer will mess up the thread's I/O
delays, which are all interruptible.
The solution to both problems is the same: Replace the kernel thread
used for scanning with a delayed-work routine on the system freezable
work queue. Freezable work queues have the nice property that you can
cancel a work item even while the work queue is frozen, and no signals
are needed.
The 3.2 version of this patch solves the problem in Bugzilla #42730.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Seth Forshee <seth.forshee@canonical.com>
CC: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI 0.96 spec says that HS bulk and control endpoint NAK rate must
be encoded as an exponent of two number of microframes. The endpoint
descriptor has the NAK rate encoded in number of microframes. We were
just copying the value from the endpoint descriptor into the endpoint
context interval field, which was not correct. This lead to the VIA
host rejecting the add of a bulk OUT endpoint from any USB 2.0 mass
storage device.
The fix is to use the correct encoding. Refactor the code to convert
number of frames to an exponential number of microframes, and make sure
we convert the number of microframes in HS bulk and control endpoints to
an exponent.
This should be back ported to kernels as old as 2.6.31, that contain the
commit dfa49c4ad1 "USB: xhci - fix math
in xhci_get_endpoint_interval"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Felipe Contreras <felipe.contreras@gmail.com>
Suggested-by: Andiry Xu <andiry.xu@amd.com>
Cc: stable@vger.kernel.org
The superspeed device attached to a USB 3.0 hub(such as VIA's)
doesn't respond the address device command after resume. The
root cause is the superspeed hub will miss the Hub Depth value
that is used as an offset into the route string to locate the
bits it uses to determine the downstream port number after
reset, and all packets can't be routed to the device attached
to the superspeed hub.
Hub driver sends a Set Hub Depth request to the superspeed hub
except for USB 3.0 root hub when the hub is initialized and
doesn't send the request again after reset due to the resume
process. So moving the code that sends the Set Hub Depth request
to the superspeed hub from hub_configure() to hub_activate()
is to cover those situations include initialization and reset.
The patch should be backported to kernels as old as 2.6.39.
Signed-off-by: Elric Fu <elricfu1@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
On some systems with an Intel Panther Point xHCI host controller, the
BIOS disables the xHCI PCI device during boot, and switches the xHCI
ports over to EHCI. This allows the BIOS to access USB devices without
having xHCI support.
The downside is that the xHCI BIOS handoff mechanism will fail because
memory mapped I/O is not enabled for the disabled PCI device.
Jesse Barnes says this is expected behavior. The PCI core will enable
BARs before quirks run, but it will leave it in an undefined state, and
it may not have memory mapped I/O enabled.
Make the generic USB quirk handler call pci_enable_device() to re-enable
MMIO, and call pci_disable_device() once the host-specific BIOS handoff
is finished. This will balance the ref counts in the PCI core. When
the PCI probe function is called, usb_hcd_pci_probe() will call
pci_enable_device() again.
This should be back ported to kernels as old as 2.6.31. That was the
first kernel with xHCI support, and no one has complained about BIOS
handoffs failing due to memory mapped I/O being disabled on other hosts
(EHCI, UHCI, or OHCI).
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@vger.kernel.org
not all platforms will use all of those ehci_*
symbols on their hc_driver structure. Sometimes
we might need to provide a modified version of
a certain method or not provide it at all, as is
the case with OMAPs which don't support port handoff
feature.
Whenever we compile a kernel for an OMAP board with
EHCI enabled, we get compile warnings:
drivers/usb/host/ehci-hub.c:1079: warning: 'ehci_relinquish_port' \
defined but not used
drivers/usb/host/ehci-hub.c:1088: warning: 'ehci_port_handed_over' \
defined but not used
In order to cleanup those warnings, we're adding
__maybe_unused annotation to those functions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a flexible USB Audio Class 2.0 compliant gadget driver that
implements a simple topology with a virtual sound card exposed at
the function side.
The driver doesn't expect any real audio codec to be present on the
function - the audio streams are simply sinked to and sourced from a
virtual ALSA sound card created. The user-space application may choose
to do whatever it wants with the data received from the USB Host and
choose to provide whatever it wants as audio data to the USB Host.
Capture(USB-Out) and Playback(USB-In) can be run at independent
configurations specified via module parameters while loading the driver.
Make this new version as the default selection by a new Kconfig choice.
Signed-off-by: Yadi Brar <yadi.brar01@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move manufacturer and product string ids into audio.c so
as to be reusable by the new uac2 version of gadget driver.
Signed-off-by: Yadi Brar <yadi.brar01@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The extant USB-Audio function driver complies to UAC_1 spec.
So name the files accordingly, paving way for inclusion of
a new UAC_2 specified driver.
Signed-off-by: Yadi Brar <yadi.brar01@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
1. Remove all old mass-storage ids's pid:
0x0026,0x0053,0x0098,0x0099,0x0149,0x0150,0x0160;
2. As the pid from 0x1401 to 0x1510 which have not surely assigned to
use for serial-port or mass-storage port,so i think it should be
removed now, and will re-add after it have assigned in future;
3. sort the pid to WCDMA and CDMA.
Signed-off-by: Rui li <li.rui27@zte.com.cn>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that USB 3.0 hub remote wakeup on port status changes is enabled,
and USB 3.0 device remote wakeup is handled in the USB core properly,
let's turn on auto-suspend for all USB 3.0 hubs.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch takes care of the race condition between the Function Wake
Device Notification and the auto-suspend timeout for this situation:
Roothub
| (U3)
hub A
| (U3)
hub B
| (U3)
device C
When device C signals a resume, the xHCI driver will set the wakeup_bits
for the roothub port that hub A is attached to. However, since USB 3.0
hubs do not set a link state change bit on device-initiated resume, hub
A will not indicate a port event when polled. Without this patch, khubd
will notice the wakeup-bits are set for the roothub port, it will resume
hub A, and then it will poll the events bits for hub A and notice that
nothing has changed. Then it will be suspended after 2 seconds.
Change hub_activate() to look at the port link state for each USB 3.0
hub port, and set hub->change_bits if the link state is U0, indicating
the device has finished resume. Change the resume function called by
hub_events(), hub_handle_remote_wakeup(), to check the link status
for resume instead of just the port's wakeup_bits.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
USB 3.0 hubs don't have a port suspend change bit (that bit is now
reserved). Instead, when a host-initiated resume finishes, the hub sets
the port link state change bit.
When a USB 3.0 device initiates remote wakeup, the parent hubs with
their upstream links in U3 will pass the LFPS up the chain. The first
hub that has an upstream link in U0 (which may be the roothub) will
reflect that LFPS back down the path to the device.
However, the parent hubs in the resumed path will not set their link
state change bit. Instead, the device that initiated the resume has to
send an asynchronous "Function Wake" Device Notification up to the host
controller. Therefore, we need a way to notify the USB core of a device
resume without going through the normal hub URB completion method.
First, make the xHCI roothub act like an external USB 3.0 hub and not
pass up the port link state change bit when a device-initiated resume
finishes. Introduce a new xHCI bit field, port_remote_wakeup, so that
we can tell the difference between a port coming out of the U3Exit state
(host-initiated resume) and the RExit state (ending state of
device-initiated resume).
Since the USB core can't tell whether a port on a hub has resumed by
looking at the Hub Status buffer, we need to introduce a bitfield,
wakeup_bits, that indicates which ports have resumed. When the xHCI
driver notices a port finishing a device-initiated resume, we call into
a new USB core function, usb_wakeup_notification(), that will set
the right bit in wakeup_bits, and kick khubd for that hub.
We also call usb_wakeup_notification() when the Function Wake Device
Notification is received by the xHCI driver. This covers the case where
the link between the roothub and the first-tier hub is in U0, and the
hub reflects the resume signaling back to the device without giving any
indication it has done so until the device sends the Function Wake
notification.
Change the code in khubd that handles the remote wakeup to look at the
state the USB core thinks the device is in, and handle the remote wakeup
if the port's wakeup bit is set.
This patch only takes care of the case where the device is attached
directly to the roothub, or the USB 3.0 hub that is attached to the root
hub is the device sending the Function Wake Device Notification (e.g.
because a new USB device was attached). The other cases will be covered
in a second patch.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Refactor the code to check for a remote wakeup on a port into its own
function. Keep the behavior the same, and set connect_change in
hub_events if the device disconnected on resume. Cleanup references to
hdev->children[i-1] to use a common variable.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
USB 3.0 hubs have a different remote wakeup policy than USB 2.0 hubs.
USB 2.0 hubs, once they have remote wakeup enabled, will always send
remote wakes when anything changes on a port.
However, USB 3.0 hubs have a per-port remote wake up policy that is off
by default. The Set Feature remote wake mask can be changed for any
port, enabling remote wakeup for a connect, disconnect, or overcurrent
event, much like EHCI and xHCI host controller "wake on" port status
bits. The bits are cleared to zero on the initial hub power on, or
after the hub has been reset.
Without this patch, when a USB 3.0 hub gets suspended, it will not send
a remote wakeup on device connect or disconnect. This would show up to
the user as "dead ports" unless they ran lsusb -v (since newer versions
of lsusb use the sysfs files, rather than sending control transfers).
Change the hub driver's suspend method to enable remote wake up for
disconnect, connect, and overcurrent for all ports on the hub. Modify
the xHCI driver's roothub code to handle that request, and set the "wake
on" bits in the port status registers accordingly.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The USB 3.0 bus specification introduces a new type of power management
called function suspend. The idea is to be able to suspend different
functions (i.e. a scanner or an SD card reader on a USB printer)
independently. A device can be in U0, but have one or more functions
suspended. Thus, signaling a function resume with the standard device
remote wake signaling was not possible.
Instead, a device will (without prompt from the host) send a "device
notification" for the function remote wake. A new Set Feature Function
Remote Wake was developed to turn remote wake up on and off for each
function.
USB 3.0 devices can still go into device suspend (U3), and signal a
remote wakeup to bring the link back into U1. However, they now use the
function remote wake device notification to allow the host to know which
function woke the device from U3.
The spec is a bit ambiguous about whether a function is allowed to
signal a remote wakeup if the function has been enabled for remote
wakeup, but not placed in function suspend before the device is placed
into U3.
Section 9.2.5.1 says "Suspending a device with more than one function
effectively suspends all the functions within the device." I interpret
that to mean that putting a device in U3 suspends all functions, and
thus if the host has previously enabled remote wake for those functions,
it should be able to signal a remote wake up on port status changes.
However, hub vendors may have a different interpretation, and it can't
hurt to put the function into suspend before putting the device into U3.
I cannot get an answer out of the USB 3.0 spec architects about this
ambiguity, so I'm erring on the safe side and always suspending the
first function before placing the device in U3. Note, this code should
be fixed if we ever find any USB 3.0 devices that have more than one
function.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When the USB 3.0 hub support went in, I disabled selective suspend for
all external USB 3.0 hubs because they used a different mechanism to
enable remote wakeup. In fact, other USB 3.0 devices that could signal
remote wakeup would have been prevented from going into suspend because
they would have stalled the SetFeature Device Remote Wakeup request.
This patch adds support for the USB 3.0 way of enabling remote wake up
(with a SetFeature Function Suspend request), and enables selective
suspend for all hubs during hub_probe. It assumes that all USB 3.0 have
only one "function" as defined by the interface association descriptor,
which is true of all the USB 3.0 devices I've seen so far. FIXME if
that turns out to change later.
After a device signals a remote wakeup, it is supposed to send a Device
Notification packet to the host controller, signaling which function
sent the remote wakeup. The host can then put any other functions back
into function suspend. Since we don't have support for function suspend
(and no devices currently support it), we'll just assume the hub
function will resume the device properly when it received the port
status change notification, and simply ignore any device notification
events from the xHCI host controller.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
xHCI roothubs go through slightly different port state machines when
either a device initiates a remote wakeup and signals resume, or when
the host initiates a resume.
According to section 4.19.1.2.13 of the xHCI 1.0 spec, on host-initiated
resume, the xHC port state machine automatically goes through the U3Exit
state into the U0 state, setting the port link state change (PLC) bit in
the process.
When a device initiates resume, the xHCI port state machine goes into
the "Resume" state and sets the PLC bit. Then the xHCI driver writes U0
into the port link state register to transition the port to U0 from the
Resume state.
We can't be sure the device is actually in the U0 state until we receive
the next port status change event with the PLC bit set. We really don't
want khubd to be polling the roothub port status bits until the device
is really in U0.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Andiry Xu <andiry.xu@amd.com>
Intel has a PCI USB xhci host controller on a new platform. It doesn't
have a line IRQ definition in BIOS. The Linux driver refuses to
initialize this controller, but Windows works well because it only depends
on MSI.
Actually, Linux also can work for MSI. This patch avoids the line IRQ
checking for USB3 HCDs in usb core PCI probe. It allows the xHCI driver
to try to enable MSI or MSI-X first. It will fail the probe if MSI
enabling failed and there's no legacy PCI IRQ.
This patch should be backported to kernels as old as 2.6.32.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The current renesas_usbhs driver triggers
BUG: scheduling while atomic: ksoftirqd/0/3/0x00000102
with enabled CONFIG_DEBUG_ATOMIC_SLEEP, by submitting DMA transfers from
an atomic (tasklet) context, which is not supported by the shdma dmaengine
driver. Fix it by switching to a work.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
list.h already provide helpers to find the first entry and to move list
nodes to the tail of another list. This patch simply uses those helpers,
no functional changes.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this will get rid of a useless memcpy on
IRQ handling, thus improving driver performance.
Tested with OMAP5430 running g_mass_storage on
SuperSpeed and HighSpeed.
Note that we are removing the little endian access
of the TRB and all accesses will be in System endianness,
if there happens to be a system in BE, bit 12 of GSBUSCFG0
should be set so that HW does byte invariant BE accesses
when fetching TRBs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
[ balbi@ti.com: added a missing change on musb_gadget.c to avoid
a compile error on a later patch ]
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Li Yang <leoli@freescale.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Introducing struct otg and collecting otg specific members
to it from struct usb_phy. There are no changes to
struct usb_phy at this stage. This also renames
transceiver specific functions, and offers aliases for the
old otg ones.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert all users.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is the first step in separating USB transceivers from
USB OTG utilities.
Includes fixes to IMX code from Sascha Hauer.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The code to set the device removable bits in the USB 2.0 roothub
descriptor was accidentally looking at the USB 3.0 port registers
instead of the USB 2.0 registers. This can cause an oops if there are
more USB 2.0 registers than USB 3.0 registers.
This should be backported to kernels as old as 2.6.39, that contain the
commit 4bbb0ace9a "xhci: Return a USB 3.0
hub descriptor for USB3 roothub."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Add a flag to tell wdm_read/wdm_write that a reset is in progress,
and wake any blocking read/write before taking the mutexes. This
allows the device to reset without waiting for blocking IO to
finish.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is done to resolve a merge conflict with:
drivers/usb/class/cdc-wdm.c
and to better handle future patches for this driver as it is under
active development at the moment.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_err_console in write paths for devices which can be used as a
console but do not use the generic write implementation.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_err_console in write path so that an error at least gets
reported once.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not report errors in write path if port is used as a console as this
may trigger the same error (and error report) resulting in a loop.
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When host requests us to enter a test mode,
we cannot directly enter the test mode before
Status Phase is completed, otherwise the core
will never be able to deliver the Status ZLP
to host, because it has already entered the
requested Test Mode.
In order to fix the error, we move the actual
start of Test Mode right after we receive
Transfer Complete event of the status phase.
Signed-off-by: Gerard Cauvy <g-cauvy1@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When implementing the USB2 testmode support via debugfs,
Felipe has committed a mistake when counting the number
of letters of some of the strings, resulting on an off
by one error which prevented some of the Test modes to
be entered properly.
This patch, fixes that mistake.
Signed-off-by: Gerard Cauvy <g-cauvy1@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Hubs have a flag to indicate whether a given port carries removable devices
or not. This is not strictly accurate in that some built-in devices
will be flagged as removable, but followup patches will make use of platform
data to make this more reliable.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Userspace may want to make policy decisions based on whether or not a
given USB device is removable. Add a per-device member and support
for exposing it in sysfs. Information sources to populate it will be
added later.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This cuts down on the boilerplate code.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the handling of the 5v supply into badge4.c, removing this board
specific detail from the sa1111 ohci driver.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add platform hooks to be called when individual sa1111 devices are
enabled and disabled. This will allow us to move some platform
specifics out of the individual drivers.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
