[ Upstream commit 0007e94355fdb71a1cf5dba0754155cba08f0666 ]
When performing a channel switch flow for a managed interface, the
flow did not update the bandwidth of the AP station and the rate
scale algorithm. In case of a channel width downgrade, this would
result with the rate scale algorithm using a bandwidth that does not
match the interface channel configuration.
Fix this by updating the AP station bandwidth and rate scaling algorithm
before the actual channel change in case of a bandwidth downgrade, or
after the actual channel change in case of a bandwidth upgrade.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f3ffb6c3a28963657eb8b02a795d75f2ebbd5ef4 ]
We hit a problem with iwlwifi that was caused by a bug in
mac80211. A bug in iwlwifi caused the firwmare to crash in
certain cases in channel switch. Because of that bug,
drv_pre_channel_switch would fail and trigger the restart
flow.
Now we had the hw restart worker which runs on the system's
workqueue and the csa_connection_drop_work worker that runs
on mac80211's workqueue that can run together. This is
obviously problematic since the restart work wants to
reconfigure the connection, while the csa_connection_drop_work
worker does the exact opposite: it tries to disconnect.
Fix this by cancelling the csa_connection_drop_work worker
in the restart worker.
Note that this can sound racy: we could have:
driver iface_work CSA_work restart_work
+++++++++++++++++++++++++++++++++++++++++++++
|
<--drv_cs ---|
<FW CRASH!>
-CS FAILED-->
| |
| cancel_work(CSA)
schedule |
CSA work |
| |
Race between those 2
But this is not possible because we flush the workqueue
in the restart worker before we cancel the CSA worker.
That would be bullet proof if we could guarantee that
we schedule the CSA worker only from the iface_work
which runs on the workqueue (and not on the system's
workqueue), but unfortunately we do have an instance
in which we schedule the CSA work outside the context
of the workqueue (ieee80211_chswitch_done).
Note also that we should probably cancel other workers
like beacon_connection_loss_work and possibly others
for different types of interfaces, at the very least,
IBSS should suffer from the exact same problem, but for
now, do the minimum to fix the actual bug that was actually
experienced and reproduced.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8442938c3a2177ba16043b3a935f2c78266ad399 ]
The "chandef->center_freq1" variable is a u32 but "freq" is a u16 so we
are truncating away the high bits. I noticed this bug because in commit
9cf0a0b4b64a ("cfg80211: Add support for 60GHz band channels 5 and 6")
we made "freq <= 56160 + 2160 * 6" a valid requency when before it was
only "freq <= 56160 + 2160 * 4" that was valid. It introduces a static
checker warning:
net/wireless/util.c:1571 ieee80211_chandef_to_operating_class()
warn: always true condition '(freq <= 56160 + 2160 * 6) => (0-u16max <= 69120)'
But really we probably shouldn't have been truncating the high bits
away to begin with.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4f0223bfe9c3e62d8f45a85f1ef1b18a8a263ef9 ]
nl80211_update_ft_ies() tried to validate NL80211_ATTR_IE with
is_valid_ie_attr() before dereferencing it, but that helper function
returns true in case of NULL pointer (i.e., attribute not included).
This can result to dereferencing a NULL pointer. Fix that by explicitly
checking that NL80211_ATTR_IE is included.
Fixes: 355199e02b ("cfg80211: Extend support for IEEE 802.11r Fast BSS Transition")
Signed-off-by: Arunk Khandavalli <akhandav@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1f631c3201fe5491808df143d8fcba81b3197ffd ]
IEEE 802.11-2016 14.10.8.3 HWMP sequence numbering says:
If it is a target mesh STA, it shall update its own HWMP SN to
maximum (current HWMP SN, target HWMP SN in the PREQ element) + 1
immediately before it generates a PREP element in response to a
PREQ element.
Signed-off-by: Yuan-Chi Pang <fu3mo6goo@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 67d1ba8a6dc83d90cd58b89fa6cbf9ae35a0cf7f ]
The mod mask for VHT capabilities intends to say that you can override
the number of STBC receive streams, and it does, but only by accident.
The IEEE80211_VHT_CAP_RXSTBC_X aren't bits to be set, but values (albeit
left-shifted). ORing the bits together gets the right answer, but we
should use the _MASK macro here instead.
Signed-off-by: Danek Duvall <duvall@comfychair.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 03bc05e1a4972f73b4eb8907aa373369e825c252 ]
After decompression of 6lowpan socket data, an IPv6 header is inserted
before the existing socket payload. After this, we reset the
network_header value of the skb to account for the difference in payload
size from prior to decompression + the addition of the IPv6 header.
However, we fail to reset the mac_header value.
Leaving the mac_header value untouched here, can cause a calculation
error in net/packet/af_packet.c packet_rcv() function when an
AF_PACKET socket is opened in SOCK_RAW mode for use on a 6lowpan
interface.
On line 2088, the data pointer is moved backward by the value returned
from skb_mac_header(). If skb->data is adjusted so that it is before
the skb->head pointer (which can happen when an old value of mac_header
is left in place) the kernel generates a panic in net/core/skbuff.c
line 1717.
This panic can be generated by BLE 6lowpan interfaces (such as bt0) and
802.15.4 interfaces (such as lowpan0) as they both use the same 6lowpan
sources for compression and decompression.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
Acked-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f0e0d04413fcce9bc76388839099aee93cd0d33b ]
Update 'confirmed' timestamp when ARP packet is received. It shouldn't
affect locktime logic and anyway entry can be confirmed by any higher-layer
protocol. Thus it makes sense to confirm it when ARP packet is received.
Fixes: 77d7123342dc ("neighbour: update neigh timestamps iff update is effective")
Signed-off-by: Vasily Khoruzhick <vasilykh@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bbd6528d28c1b8e80832b3b018ec402b6f5c3215 ]
In the unlikely case ip6_xmit() has to call skb_realloc_headroom(),
we need to call skb_set_owner_w() before consuming original skb,
otherwise we risk a use-after-free.
Bring IPv6 in line with what we do in IPv4 to fix this.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c56cae23c6b167acc68043c683c4573b80cbcc2c ]
When splitting a GSO segment that consists of encapsulated packets, the
skb->mac_len of the segments can end up being set wrong, causing packet
drops in particular when using act_mirred and ifb interfaces in
combination with a qdisc that splits GSO packets.
This happens because at the time skb_segment() is called, network_header
will point to the inner header, throwing off the calculation in
skb_reset_mac_len(). The network_header is subsequently adjust by the
outer IP gso_segment handlers, but they don't set the mac_len.
Fix this by adding skb_reset_mac_len() calls to both the IPv4 and IPv6
gso_segment handlers, after they modify the network_header.
Many thanks to Eric Dumazet for his help in identifying the cause of
the bug.
Acked-by: Dave Taht <dave.taht@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 674d9de02aa7d521ebdf66c3958758bdd9c64e11 upstream.
When handling SHDLC I-Frame commands "pipe" field used for indexing
into an array should be checked before usage. If left unchecked it
might access memory outside of the array of size NFC_HCI_MAX_PIPES(127).
Malformed NFC HCI frames could be injected by a malicious NFC device
communicating with the device being attacked (remote attack vector),
or even by an attacker with physical access to the I2C bus such that
they could influence the data transfers on that bus (local attack vector).
skb->data is controlled by the attacker and has only been sanitized in
the most trivial ways (CRC check), therefore we can consider the
create_info struct and all of its members to tainted. 'create_info->pipe'
with max value of 255 (uint8) is used to take an offset of the
hdev->pipes array of 127 elements which can lead to OOB write.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Allen Pais <allen.pais@oracle.com>
Cc: "David S. Miller" <davem@davemloft.net>
Suggested-by: Kevin Deus <kdeus@google.com>
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 133bf90dbb8b873286f8ec2e81ba26e863114b8c ]
As explained in ieee80211_delayed_tailroom_dec(), during roam,
keys of the old AP will be destroyed and new keys will be
installed. Deletion of the old key causes
crypto_tx_tailroom_needed_cnt to go from 1 to 0 and the new key
installation causes a transition from 0 to 1.
Whenever crypto_tx_tailroom_needed_cnt transitions from 0 to 1,
we invoke synchronize_net(); the reason for doing this is to avoid
a race in the TX path as explained in increment_tailroom_need_count().
This synchronize_net() operation can be slow and can affect the station
roam time. To avoid this, decrementing the crypto_tx_tailroom_needed_cnt
is delayed for a while so that upon installation of new key the
transition would be from 1 to 2 instead of 0 to 1 and thereby
improving the roam time.
This is all correct for a STA iftype, but deferring the tailroom_needed
decrement for other iftypes may be unnecessary.
For example, let's consider the case of a 4-addr client connecting to
an AP for which AP_VLAN interface is also created, let the initial
value for tailroom_needed on the AP be 1.
* 4-addr client connects to the AP (AP: tailroom_needed = 1)
* AP will clear old keys, delay decrement of tailroom_needed count
* AP_VLAN is created, it takes the tailroom count from master
(AP_VLAN: tailroom_needed = 1, AP: tailroom_needed = 1)
* Install new key for the station, assume key is plumbed in the HW,
there won't be any change in tailroom_needed count on AP iface
* Delayed decrement of tailroom_needed count on AP
(AP: tailroom_needed = 0, AP_VLAN: tailroom_needed = 1)
Because of the delayed decrement on AP iface, tailroom_needed count goes
out of sync between AP(master iface) and AP_VLAN(slave iface) and
there would be unnecessary tailroom created for the packets going
through AP_VLAN iface.
Also, WARN_ONs were observed while trying to bring down the AP_VLAN
interface:
(warn_slowpath_common) (warn_slowpath_null+0x18/0x20)
(warn_slowpath_null) (ieee80211_free_keys+0x114/0x1e4)
(ieee80211_free_keys) (ieee80211_del_virtual_monitor+0x51c/0x850)
(ieee80211_del_virtual_monitor) (ieee80211_stop+0x30/0x3c)
(ieee80211_stop) (__dev_close_many+0x94/0xb8)
(__dev_close_many) (dev_close_many+0x5c/0xc8)
Restricting delayed decrement to station interface alone fixes the problem
and it makes sense to do so because delayed decrement is done to improve
roam time which is applicable only for client devices.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e466af75c074e76107ae1cd5a2823e9c61894ffb upstream.
syzkaller reports an out of bound read in strlcpy(), triggered
by xt_copy_counters_from_user()
Fix this by using memcpy(), then forcing a zero byte at the last position
of the destination, as Florian did for the non COMPAT code.
Fixes: d7591f0c41ce ("netfilter: x_tables: introduce and use xt_copy_counters_from_user")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Greg Hackmann <ghackmann@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 08193d1a893c802c4b807e4d522865061f4e9f4f ]
The function dcb_app_lookup walks the list of specified DCB APP entries,
looking for one that matches a given criteria: ifindex, selector,
protocol ID and optionally also priority. The "don't care" value for
priority is set to 0, because that priority has not been allowed under
CEE regime, which predates the IEEE standardization.
Under IEEE, 0 is a valid priority number. But because dcb_app_lookup
considers zero a wild card, attempts to add an APP entry with priority 0
fail when other entries exist for a given ifindex / selector / PID
triplet.
Fix by changing the wild-card value to -1.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b3cadaa485f0c20add1644a5c877b0765b285c0c ]
This fixes two issues with setting hid->name information.
CC net/bluetooth/hidp/core.o
In function ‘hidp_setup_hid’,
inlined from ‘hidp_session_dev_init’ at net/bluetooth/hidp/core.c:815:9,
inlined from ‘hidp_session_new’ at net/bluetooth/hidp/core.c:953:8,
inlined from ‘hidp_connection_add’ at net/bluetooth/hidp/core.c:1366:8:
net/bluetooth/hidp/core.c:778:2: warning: ‘strncpy’ output may be truncated copying 127 bytes from a string of length 127 [-Wstringop-truncation]
strncpy(hid->name, req->name, sizeof(req->name) - 1);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
CC net/bluetooth/hidp/core.o
net/bluetooth/hidp/core.c: In function ‘hidp_setup_hid’:
net/bluetooth/hidp/core.c:778:38: warning: argument to ‘sizeof’ in ‘strncpy’ call is the same expression as the source; did you mean to use the size of the destination? [-Wsizeof-pointer-memaccess]
strncpy(hid->name, req->name, sizeof(req->name));
^
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The irda_setsockopt() function conditionally allocates memory for a new
self->ias_object or, in some cases, reuses the existing
self->ias_object. Existing objects were incorrectly reinserted into the
LM_IAS database which corrupted the doubly linked list used for the
hashbin implementation of the LM_IAS database. When combined with a
memory leak in irda_bind(), this issue could be leveraged to create a
use-after-free vulnerability in the hashbin list. This patch fixes the
issue by only inserting newly allocated objects into the database.
CVE-2018-6555
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Reviewed-by: Seth Arnold <seth.arnold@canonical.com>
Reviewed-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The irda_bind() function allocates memory for self->ias_obj without
checking to see if the socket is already bound. A userspace process
could repeatedly bind the socket, have each new object added into the
LM-IAS database, and lose the reference to the old object assigned to
the socket to exhaust memory resources. This patch errors out of the
bind operation when self->ias_obj is already assigned.
CVE-2018-6554
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Reviewed-by: Seth Arnold <seth.arnold@canonical.com>
Reviewed-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 92aef4675d5b1b55404e1532379e343bed0e5cf2 ]
Currently when virtio_find_single_vq fails, we go through del_vqs which
throws a warning (Trying to free already-free IRQ). Skip del_vqs if vq
allocation failed.
Link: http://lkml.kernel.org/r/20180524101021.49880-1-jean-philippe.brucker@arm.com
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dominique Martinet <dominique.martinet@cea.fr>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a53b42c11815d2357e31a9403ae3950517525894 ]
We came across infinite loop in ipvs when using ipvs in docker
env.
When ipvs receives new packets and cannot find an ipvs connection,
it will create a new connection, then if the dest is unavailable
(i.e. IP_VS_DEST_F_AVAILABLE), the packet will be dropped sliently.
But if the dropped packet is the first packet of this connection,
the connection control timer never has a chance to start and the
ipvs connection cannot be released. This will lead to memory leak, or
infinite loop in cleanup_net() when net namespace is released like
this:
ip_vs_conn_net_cleanup at ffffffffa0a9f31a [ip_vs]
__ip_vs_cleanup at ffffffffa0a9f60a [ip_vs]
ops_exit_list at ffffffff81567a49
cleanup_net at ffffffff81568b40
process_one_work at ffffffff810a851b
worker_thread at ffffffff810a9356
kthread at ffffffff810b0b6f
ret_from_fork at ffffffff81697a18
race condition:
CPU1 CPU2
ip_vs_in()
ip_vs_conn_new()
ip_vs_del_dest()
__ip_vs_unlink_dest()
~IP_VS_DEST_F_AVAILABLE
cp->dest && !IP_VS_DEST_F_AVAILABLE
__ip_vs_conn_put
...
cleanup_net ---> infinite looping
Fix this by checking whether the timer already started.
Signed-off-by: Tan Hu <tan.hu@zte.com.cn>
Reviewed-by: Jiang Biao <jiang.biao2@zte.com.cn>
Acked-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9f2895461439fda2801a7906fb4c5fb3dbb37a0a ]
Before the commit d6990976af7c ("vti6: fix PMTU caching and reporting
on xmit") '!skb->ignore_df' check was always true because the function
skb_scrub_packet() was called before it, resetting ignore_df to zero.
In the commit, skb_scrub_packet() was moved below, and now this check
can be false for the packet, e.g. when sending it in the two fragments,
this prevents successful PMTU updates in such case. The next attempts
to send the packet lead to the same tx error. Moreover, vti6 initial
MTU value relies on PMTU adjustments.
This issue can be reproduced with the following LTP test script:
udp_ipsec_vti.sh -6 -p ah -m tunnel -s 2000
Fixes: ccd740cbc6 ("vti6: Add pmtu handling to vti6_xmit.")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 63cc357f7bba6729869565a12df08441a5995d9a ]
RFC 1337 says:
''Ignore RST segments in TIME-WAIT state.
If the 2 minute MSL is enforced, this fix avoids all three hazards.''
So with net.ipv4.tcp_rfc1337=1, expected behaviour is to have TIME-WAIT sk
expire rather than removing it instantly when a reset is received.
However, Linux will also re-start the TIME-WAIT timer.
This causes connect to fail when tying to re-use ports or very long
delays (until syn retry interval exceeds MSL).
packetdrill test case:
// Demonstrate bogus rearming of TIME-WAIT timer in rfc1337 mode.
`sysctl net.ipv4.tcp_rfc1337=1`
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
0.000 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
0.000 bind(3, ..., ...) = 0
0.000 listen(3, 1) = 0
0.100 < S 0:0(0) win 29200 <mss 1460,nop,nop,sackOK,nop,wscale 7>
0.100 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 7>
0.200 < . 1:1(0) ack 1 win 257
0.200 accept(3, ..., ...) = 4
// Receive first segment
0.310 < P. 1:1001(1000) ack 1 win 46
// Send one ACK
0.310 > . 1:1(0) ack 1001
// read 1000 byte
0.310 read(4, ..., 1000) = 1000
// Application writes 100 bytes
0.350 write(4, ..., 100) = 100
0.350 > P. 1:101(100) ack 1001
// ACK
0.500 < . 1001:1001(0) ack 101 win 257
// close the connection
0.600 close(4) = 0
0.600 > F. 101:101(0) ack 1001 win 244
// Our side is in FIN_WAIT_1 & waits for ack to fin
0.7 < . 1001:1001(0) ack 102 win 244
// Our side is in FIN_WAIT_2 with no outstanding data.
0.8 < F. 1001:1001(0) ack 102 win 244
0.8 > . 102:102(0) ack 1002 win 244
// Our side is now in TIME_WAIT state, send ack for fin.
0.9 < F. 1002:1002(0) ack 102 win 244
0.9 > . 102:102(0) ack 1002 win 244
// Peer reopens with in-window SYN:
1.000 < S 1000:1000(0) win 9200 <mss 1460,nop,nop,sackOK,nop,wscale 7>
// Therefore, reply with ACK.
1.000 > . 102:102(0) ack 1002 win 244
// Peer sends RST for this ACK. Normally this RST results
// in tw socket removal, but rfc1337=1 setting prevents this.
1.100 < R 1002:1002(0) win 244
// second syn. Due to rfc1337=1 expect another pure ACK.
31.0 < S 1000:1000(0) win 9200 <mss 1460,nop,nop,sackOK,nop,wscale 7>
31.0 > . 102:102(0) ack 1002 win 244
// .. and another RST from peer.
31.1 < R 1002:1002(0) win 244
31.2 `echo no timer restart;ss -m -e -a -i -n -t -o state TIME-WAIT`
// third syn after one minute. Time-Wait socket should have expired by now.
63.0 < S 1000:1000(0) win 9200 <mss 1460,nop,nop,sackOK,nop,wscale 7>
// so we expect a syn-ack & 3whs to proceed from here on.
63.0 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 7>
Without this patch, 'ss' shows restarts of tw timer and last packet is
thus just another pure ack, more than one minute later.
This restores the original code from commit 283fd6cf0be690a83
("Merge in ANK networking jumbo patch") in netdev-vger-cvs.git .
For some reason the else branch was removed/lost in 1f28b683339f7
("Merge in TCP/UDP optimizations and [..]") and timer restart became
unconditional.
Reported-by: Michal Tesar <mtesar@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 430ac66eb4c5b5c4eb846b78ebf65747510b30f1 upstream.
The patch adds the flush in p9_mux_poll_stop() as it the function used by
p9_conn_destroy(), in turn called by p9_fd_close() to stop the async
polling associated with the data regarding the connection.
Link: http://lkml.kernel.org/r/20180720092730.27104-1-tomasbortoli@gmail.com
Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+39749ed7d9ef6dfb23f6@syzkaller.appspotmail.com
To: Eric Van Hensbergen <ericvh@gmail.com>
To: Ron Minnich <rminnich@sandia.gov>
To: Latchesar Ionkov <lucho@ionkov.net>
Cc: Yiwen Jiang <jiangyiwen@huwei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dominique Martinet <dominique.martinet@cea.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7913690dcc5e18e235769fd87c34143072f5dbea upstream.
The p9_client_version() does not initialize the version pointer. If the
call to p9pdu_readf() returns an error and version has not been allocated
in p9pdu_readf(), then the program will jump to the "error" label and will
try to free the version pointer. If version is not initialized, free()
will be called with uninitialized, garbage data and will provoke a crash.
Link: http://lkml.kernel.org/r/20180709222943.19503-1-tomasbortoli@gmail.com
Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+65c6b72f284a39d416b4@syzkaller.appspotmail.com
Reviewed-by: Jun Piao <piaojun@huawei.com>
Reviewed-by: Yiwen Jiang <jiangyiwen@huawei.com>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dominique Martinet <dominique.martinet@cea.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23cba9cbde0bba05d772b335fe5f66aa82b9ad19 upstream.
Because the value of limit is VIRTQUEUE_NUM, if index is equal to
limit, it will cause sg array out of bounds, so correct the judgement
of BUG_ON.
Link: http://lkml.kernel.org/r/5B63D5F6.6080109@huawei.com
Signed-off-by: Yiwen Jiang <jiangyiwen@huawei.com>
Reported-By: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jun Piao <piaojun@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dominique Martinet <dominique.martinet@cea.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d28c756caee6e414d9ba367d0b92da24145af2a8 upstream.
The zero-copy optimization when reading or writing large chunks of data
is quite useful. However, the 9p messages created through the zero-copy
write path have an incorrect message size: it should be the size of the
header + size of the data being written but instead it's just the size
of the header.
This only works if the server ignores the size field of the message and
otherwise breaks the framing of the protocol. Fix this by re-writing the
message size field with the correct value.
Tested by running `dd if=/dev/zero of=out bs=4k count=1` inside a
virtio-9p mount.
Link: http://lkml.kernel.org/r/20180717003529.114368-1-chirantan@chromium.org
Signed-off-by: Chirantan Ekbote <chirantan@chromium.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
Cc: Dylan Reid <dgreid@chromium.org>
Cc: Guenter Roeck <groeck@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dominique Martinet <dominique.martinet@cea.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9c52831133050c6b82aa8b6831c92da2bbf2a0b upstream.
This patch is necessary if case of AF_PACKET or other socket interface
which I am aware of it and didn't allocated the necessary room.
Reported-by: David Palma <david.palma@ntnu.no>
Reported-by: Rabi Narayan Sahoo <rabinarayans0828@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac74f87c789af40936a80131c4759f3e72579c3a upstream.
This patch fixes patch add handling to take care tail and headroom for
single 6lowpan frames. We need to be sure we have a skb with the right
head and tailroom for single frames. This patch do it by using
skb_copy_expand() if head and tailroom is not enough allocated by upper
layer.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195059
Reported-by: David Palma <david.palma@ntnu.no>
Reported-by: Rabi Narayan Sahoo <rabinarayans0828@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5cf3006cc81d9aa09a10aa781fc065546b12919d ]
I was looking at usually suppressed gcc warnings,
[-Wimplicit-fallthrough=] in this case:
The code definitely looks like a break is missing here.
However I am not able to test the NL80211_IFTYPE_MESH_POINT,
nor do I actually know what might be :)
So please use this patch with caution and only if you are
able to do some testing.
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
[johannes: looks obvious enough to apply as is, interesting
though that it never seems to have been a problem]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 19103a4bfb42f320395daa5616ece3e89e759d63 ]
As part of hw reconfig, only stations linked to AP interfaces are added
back to the driver ignoring those which are tied to AP_VLAN interfaces.
It is true that there could be stations tied to the AP_VLAN interface while
serving 4addr clients or when using AP_VLAN for VLAN operations; we should
be adding these stations back to the driver as part of hw reconfig, failing
to do so can cause functional issues.
In the case of ath10k driver, the following errors were observed.
ath10k_pci : failed to install key for non-existent peer XX:XX:XX:XX:XX:XX
Workqueue: events_freezable ieee80211_restart_work [mac80211]
(unwind_backtrace) from (show_stack+0x10/0x14)
(show_stack) (dump_stack+0x80/0xa0)
(dump_stack) (warn_slowpath_common+0x68/0x8c)
(warn_slowpath_common) (warn_slowpath_null+0x18/0x20)
(warn_slowpath_null) (ieee80211_enable_keys+0x88/0x154 [mac80211])
(ieee80211_enable_keys) (ieee80211_reconfig+0xc90/0x19c8 [mac80211])
(ieee80211_reconfig]) (ieee80211_restart_work+0x8c/0xa0 [mac80211])
(ieee80211_restart_work) (process_one_work+0x284/0x488)
(process_one_work) (worker_thread+0x228/0x360)
(worker_thread) (kthread+0xd8/0xec)
(kthread) (ret_from_fork+0x14/0x24)
Also while bringing down the AP VAP, WARN_ONs and errors related to peer
removal were observed.
ath10k_pci : failed to clear all peer wep keys for vdev 0: -2
ath10k_pci : failed to disassociate station: 8c:fd:f0:0a:8c:f5 vdev 0: -2
(unwind_backtrace) (show_stack+0x10/0x14)
(show_stack) (dump_stack+0x80/0xa0)
(dump_stack) (warn_slowpath_common+0x68/0x8c)
(warn_slowpath_common) (warn_slowpath_null+0x18/0x20)
(warn_slowpath_null) (sta_set_sinfo+0xb98/0xc9c [mac80211])
(sta_set_sinfo [mac80211]) (__sta_info_flush+0xf0/0x134 [mac80211])
(__sta_info_flush [mac80211]) (ieee80211_stop_ap+0xe8/0x390 [mac80211])
(ieee80211_stop_ap [mac80211]) (__cfg80211_stop_ap+0xe0/0x3dc [cfg80211])
(__cfg80211_stop_ap [cfg80211]) (cfg80211_stop_ap+0x30/0x44 [cfg80211])
(cfg80211_stop_ap [cfg80211]) (genl_rcv_msg+0x274/0x30c)
(genl_rcv_msg) (netlink_rcv_skb+0x58/0xac)
(netlink_rcv_skb) (genl_rcv+0x20/0x34)
(genl_rcv) (netlink_unicast+0x11c/0x204)
(netlink_unicast) (netlink_sendmsg+0x30c/0x370)
(netlink_sendmsg) (sock_sendmsg+0x70/0x84)
(sock_sendmsg) (___sys_sendmsg.part.3+0x188/0x228)
(___sys_sendmsg.part.3) (__sys_sendmsg+0x4c/0x70)
(__sys_sendmsg) (ret_fast_syscall+0x0/0x44)
These issues got fixed by adding the stations which are
tied to AP_VLANs back to the driver.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 86126b77dcd551ce223e7293bb55854e3df05646 ]
nlmsg_multicast() always frees the skb, so in case we cannot call
it we must do that ourselves.
Fixes: 21ee543edc ("xfrm: fix race between netns cleanup and state expire notification")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8cc88773855f988d6a3bbf102bbd9dd9c828eb81 ]
Fix missing dst_release() when local broadcast or multicast traffic is
xfrm policy blocked.
For IPv4 this results to dst leak: ip_route_output_flow() allocates
dst_entry via __ip_route_output_key() and passes it to
xfrm_lookup_route(). xfrm_lookup returns ERR_PTR(-EPERM) that is
propagated. The dst that was allocated is never released.
IPv4 local broadcast testcase:
ping -b 192.168.1.255 &
sleep 1
ip xfrm policy add src 0.0.0.0/0 dst 192.168.1.255/32 dir out action block
IPv4 multicast testcase:
ping 224.0.0.1 &
sleep 1
ip xfrm policy add src 0.0.0.0/0 dst 224.0.0.1/32 dir out action block
For IPv6 the missing dst_release() causes trouble e.g. when used in netns:
ip netns add TEST
ip netns exec TEST ip link set lo up
ip link add dummy0 type dummy
ip link set dev dummy0 netns TEST
ip netns exec TEST ip addr add fd00::1111 dev dummy0
ip netns exec TEST ip link set dummy0 up
ip netns exec TEST ping -6 -c 5 ff02::1%dummy0 &
sleep 1
ip netns exec TEST ip xfrm policy add src ::/0 dst ff02::1 dir out action block
wait
ip netns del TEST
After netns deletion we see:
[ 258.239097] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 268.279061] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 278.367018] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 288.375259] unregister_netdevice: waiting for lo to become free. Usage count = 2
Fixes: ac37e2515c ("xfrm: release dst_orig in case of error in xfrm_lookup()")
Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d6990976af7c5d8f55903bfb4289b6fb030bf754 ]
When setting the skb->dst before doing the MTU check, the route PMTU
caching and reporting is done on the new dst which is about to be
released.
Instead, PMTU handling should be done using the original dst.
This is aligned with IPv4 VTI.
Fixes: ccd740cbc6 ("vti6: Add pmtu handling to vti6_xmit.")
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40413955ee265a5e42f710940ec78f5450d49149 upstream.
in for(),if((optlen > 0) && (optptr[1] == 0)), enter infinite loop.
Test: receive a packet which the ip length > 20 and the first byte of ip option is 0, produce this issue
Signed-off-by: yujuan.qi <yujuan.qi@mediatek.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08474cc1e6ea71237cab7e4a651a623c9dea1084 upstream.
Disallow adding interfaces to a bridge when vlan filtering operation
failed. Send the failure code to the user.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4576cd469d980317c4edd9173f8b694aa71ea3a3 upstream.
TPACKET_V3 stores variable length frames in fixed length blocks.
Blocks must be able to store a block header, optional private space
and at least one minimum sized frame.
Frames, even for a zero snaplen packet, store metadata headers and
optional reserved space.
In the block size bounds check, ensure that the frame of the
chosen configuration fits. This includes sockaddr_ll and optional
tp_reserve.
Syzbot was able to construct a ring with insuffient room for the
sockaddr_ll in the header of a zero-length frame, triggering an
out-of-bounds write in dev_parse_header.
Convert the comparison to less than, as zero is a valid snap len.
This matches the test for minimum tp_frame_size immediately below.
Fixes: f6fb8f100b ("af-packet: TPACKET_V3 flexible buffer implementation.")
Fixes: eb73190f4fbe ("net/packet: refine check for priv area size")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6613b6173dee098997229caf1f3b961c49da75e6 upstream.
When first DCCP packet is SYNC or SYNCACK, we insert a new conntrack
that has an un-initialized timeout value, i.e. such entry could be
reaped at any time.
Mark them as INVALID and only ignore SYNC/SYNCACK when connection had
an old state.
Reported-by: syzbot+6f18401420df260e37ed@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e56b8ce363a36fb7b74b80aaa5cc9084f2c908b4 ]
Attempt to make cryptic TCP seq number error messages clearer by
(1) identifying the source of the message as "TCP", (2) identifying the
errors as "seq # bug", and (3) grouping the field identifiers and values
by separating them with commas.
E.g., the following message is changed from:
recvmsg bug 2: copied 73BCB6CD seq 70F17CBE rcvnxt 73BCB9AA fl 0
WARNING: CPU: 2 PID: 1501 at /linux/net/ipv4/tcp.c:1881 tcp_recvmsg+0x649/0xb90
to:
TCP recvmsg seq # bug 2: copied 73BCB6CD, seq 70F17CBE, rcvnxt 73BCB9AA, fl 0
WARNING: CPU: 2 PID: 1501 at /linux/net/ipv4/tcp.c:2011 tcp_recvmsg+0x694/0xba0
Suggested-by: 積丹尼 Dan Jacobson <jidanni@jidanni.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a69258f7aa2623e0930212f09c586fd06674ad79 ]
After fixing the way DCTCP tracking delayed ACKs, the delayed-ACK
related callbacks are no longer needed
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 993675a3100b16a4c80dfd70cbcde8ea7127b31d ]
If variable length link layer headers result in a packet shorter
than dev->hard_header_len, reset the network header offset. Else
skb->mac_len may exceed skb->len after skb_mac_reset_len.
packet_sendmsg_spkt already has similar logic.
Fixes: b84bbaf7a6c8 ("packet: in packet_snd start writing at link layer allocation")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d376bef9c29b3c65aeee4e785fffcd97ef0a9a81 ]
nft_compat relies on xt_request_find_match to increment
refcount of the module that provides the match/target.
The (builtin) icmp matches did't set the module owner so it
was possible to rmmod ip(6)tables while icmp extensions were still in use.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
