For some reasons (bridge forward delay, network device setup order, etc)
the initial bridge loop avoidance announcement packets may be lost. This
may lead to problems in finding other backbone gws, and therfore create
loops in the startup time.
Fix this by extending the waiting periods to 3 (define can be changed)
before allowing broadcast traffic.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
When adding a backbone gateway for the first time, it might not yet
be known in the backbone, and therefore we should not forward
broadcasts yet. This behaviour is the same as when sending a request
to another backbone gw because of a CRC mismatch. The backbone gw
will operate normal after the next periodic bla work.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
To avoid loops in the startup phase until the first announcement is
sent, send an announcement immediately as soon as a backbone gw is
added.
This may happen due to various reasons, e.g. a packet passes the rx
or tx path.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Any virtual device created on top of a batman-adv mesh interface must be
prevented to be used to create a new mesh network (this would lead to an
unwanted batman-over-batman configuration)
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The hash functions in the bridge loop avoidance code expects the
VLAN vid to be right after the mac address, but this is not guaranteed.
Fix this by explicitly hashing over the right fields of the struct.
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Allow drivers to indicate their mactime is at RX completion and adjust
for this in mac80211. Also rename the existing RX_FLAG_MACTIME_MPDU to
RX_FLAG_MACTIME_START to clarify its intent. Based on similar code by
Johannes Berg.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
[fix docs, atheros drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The check whether the IBSS is active and can be removed should be
performed before deinitializing the fields used for the check/search.
Otherwise, the configured BSS will not be found and removed properly.
To make it more clear for the future, rename sdata->u.ibss to the
local pointer ifibss which is used within the checks.
This behaviour was introduced by
f3209bea11
("mac80211: fix IBSS teardown race")
Cc: stable@vger.kernel.org
Cc: Ignacy Gawedzki <i@lri.fr>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We added support for RFC 5961 in latest kernels but TCP fails
to perform exhaustive check of ACK sequence.
We can update our view of peer tsval from a frame that is
later discarded by tcp_ack()
This makes timestamps enabled sessions vulnerable to injection of
a high tsval : peers start an ACK storm, since the victim
sends a dupack each time it receives an ACK from the other peer.
As tcp_validate_incoming() is called before tcp_ack(), we should
not peform tcp_replace_ts_recent() from it, and let callers do it
at the right time.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: H.K. Jerry Chu <hkchu@google.com>
Cc: Romain Francoise <romain@orebokech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a new knob ndisc_notify. If enabled, the kernel
will transmit an unsolicited neighbour advertisement on link-layer address
change to update the neighbour tables of the corresponding hosts more quickly.
This is the equivalent to arp_notify in ipv4 world.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
yoshfuji points out that sk_bound_dev_if should only be provided
for link-local addresses.
IPv6 getpeer/sockname also has this test, i.e. we will now
only set sin6_scope_id if the original(!) destination
was a link-local address.
Reported-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The xfrm gc threshold value depends on ip_rt_max_size. This
value was set to INT_MAX with the routing cache removal patch,
so we start doing garbage collecting when we have INT_MAX/2
IPsec routes cached. Fix this by going back to the static
threshold of 1024 routes.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch prepares ipv6_find_hdr() function so that it could be
able to skip routing headers, where segements_left is 0. This is
required to handle multiple routing header case correctly when
changing IPv6 addresses.
Signed-off-by: Ansis Atteka <aatteka@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
When in world roaming mode, allow 40 MHz to be used
on channels 12 and 13 so that an AP that is, e.g.,
using HT40+ on channel 9 (in the UK) can be used.
Cc: stable@vger.kernel.org
Reported-by: Eddie Chapman <eddie@ehuk.net>
Tested-by: Eddie Chapman <eddie@ehuk.net>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
(1<<optname) is undefined behavior in C with a negative optname or
optname larger than 31. In those cases the result of the shift is
not necessarily zero (e.g., on x86).
This patch simplifies the code with a switch statement on optname.
It also allows the compiler to generate better code (e.g., using a
64-bit mask).
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Bug fixes galore, mostly in drivers as is often the case:
1) USB gadget and cdc_eem drivers need adjustments to their frame size
lengths in order to handle VLANs correctly. From Ian Coolidge.
2) TIPC and several network drivers erroneously call tasklet_disable
before tasklet_kill, fix from Xiaotian Feng.
3) r8169 driver needs to apply the WOL suspend quirk to more chipsets,
fix from Cyril Brulebois.
4) Fix multicast filters on RTL_GIGA_MAC_VER_35 r8169 chips, from
Nathan Walp.
5) FDB netlink dumps should use RTM_NEWNEIGH as the message type, not
zero. From John Fastabend.
6) Fix smsc95xx tx checksum offload on big-endian, from Steve
Glendinning.
7) __inet_diag_dump() needs to repsect and report the error value
returned from inet_diag_lock_handler() rather than ignore it.
Otherwise if an inet diag handler is not available for a particular
protocol, we essentially report success instead of giving an error
indication. Fix from Cyrill Gorcunov.
8) When the QFQ packet scheduler sees TSO/GSO packets it does not
handle things properly, and in fact ends up corrupting it's
datastructures as well as mis-schedule packets. Fix from Paolo
Valente.
9) Fix oopser in skb_loop_sk(), from Eric Leblond.
10) CXGB4 passes partially uninitialized datastructures in to FW
commands, fix from Vipul Pandya.
11) When we send unsolicited ipv6 neighbour advertisements, we should
send them to the link-local allnodes multicast address, as per
RFC4861. Fix from Hannes Frederic Sowa.
12) There is some kind of bug in the usbnet's kevent deferral
mechanism, but more immediately when it triggers an uncontrolled
stream of kernel messages spam the log. Rate limit the error log
message triggered when this problem occurs, as sending thousands
of error messages into the kernel log doesn't help matters at all,
and in fact makes further diagnosis more difficult.
From Steve Glendinning.
13) Fix gianfar restore from hibernation, from Wang Dongsheng.
14) The netlink message attribute sizes are wrong in the ipv6 GRE
driver, it was using the size of ipv4 addresses instead of ipv6
ones :-) Fix from Nicolas Dichtel."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
gre6: fix rtnl dump messages
gianfar: ethernet vanishes after restoring from hibernation
usbnet: ratelimit kevent may have been dropped warnings
ipv6: send unsolicited neighbour advertisements to all-nodes
net: usb: cdc_eem: Fix rx skb allocation for 802.1Q VLANs
usb: gadget: g_ether: fix frame size check for 802.1Q
cxgb4: Fix initialization of SGE_CONTROL register
isdn: Make CONFIG_ISDN depend on CONFIG_NETDEVICES
cxgb4: Initialize data structures before using.
af-packet: fix oops when socket is not present
pkt_sched: enable QFQ to support TSO/GSO
net: inet_diag -- Return error code if protocol handler is missed
net: bnx2x: Fix typo in bnx2x driver
smsc95xx: fix tx checksum offload for big endian
rtnetlink: Use nlmsg type RTM_NEWNEIGH from dflt fdb dump
ptp: update adjfreq callback description
r8169: allow multicast packets on sub-8168f chipset.
r8169: Fix WoL on RTL8168d/8111d.
drivers/net: use tasklet_kill in device remove/close process
tipc: do not use tasklet_disable before tasklet_kill
Fixes more wifi status skb leaks, leading to hostapd/wpa_supplicant hangs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Open vSwitch will soon also use ipv6_find_hdr() so this moves it
out of Netfilter-specific code into a more common location.
Signed-off-by: Jesse Gross <jesse@nicira.com>
It is usefull for daemons that monitor link event to have the full parameters of
these interfaces when a rtnl message is sent.
It allows also to dump them via rtnetlink.
It is based on what is done for GRE tunnels.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is usefull for daemons that monitor link event to have the full parameters of
these interfaces when a rtnl message is sent.
It allows also to dump them via rtnetlink.
It is based on what is done for GRE tunnels.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is usefull for daemons that monitor link event to have the full parameters of
these interfaces when a rtnl message is sent.
It allows also to dump them via rtnetlink.
It is based on what is done for GRE tunnels.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spotted after a code review.
Introduced by c12b395a46 (gre: Support GRE over
IPv6).
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 6b78f16e4b (gre: add GSO support) we added GSO support to GRE
tunnels.
This patch does the same for IPIP tunnels.
Performance of single TCP flow over an IPIP tunnel is increased by 40%
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As documented in RFC4861 (Neighbor Discovery for IP version 6) 7.2.6.,
unsolicited neighbour advertisements should be sent to the all-nodes
multicast address.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since channel contexts are usually present before
stations can be added to an interface, reassign
before stations them in reconfiguration as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During hardware restart, all interfaces are iterated even
though they haven't been re-added to the driver, document
this behaviour. The same also happens during resume, which
is even more confusing since all of the interfaces were
previously removed from the driver. Make this optional so
drivers relying on the current behaviour can still use it,
but to let drivers that don't want this behaviour disable
it.
Also convert all API users, keeping the old semantics
except in hwsim, where the new normal ones are desired.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver requests a restart (reconfiguration) it
gets all the normal method calls, but can't really tell
why they're happening. Call a new restart_complete op
in the driver when the restart completes, so it could
keep its own state about the restart and clear it there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On resume or firmware recovery, mac80211 sends a null
data packet to see if the AP is still around and hasn't
disconnected us. However, it always does this even if
it wasn't even connected before, leading to a warning
in the new channel context code. Fix this by checking
that it's associated.
Cc: stable@vger.kernel.org
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clearly the tracepoint drv_offchannel_tx was
forgotten when that functionality was removed,
remove it now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a debugfs file showing which HW queues were
allocated to a virtual interface, including the
CAB queue for AP interfaces.
Change-Id: I486924e961b6ad6785a79db09620919ee644e703
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When removing a UUID from the list in the remove_uuid() function we must
also kfree the entry in addition to removing it from the list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
It is important that the monitor interface gets notified about
a new device before its power on procedure has been started.
For some reason that is no longer working as expected and the power
on procedure runs first. It is safe to just notify about device
registration and trigger the power on procedure afterwards.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When pairing fails due to wrong confirm value, the management layer
doesn't report a proper error status. It sends
MGMT_STATUS_CONNECT_FAILED instead of MGMT_STATUS_AUTH_FAILED.
Most of management functions that receive a status as a parameter
expects for it to be encoded as a HCI status. But when a SMP pairing
fails, the SMP layer sends the SMP reason as the error status to the
management layer.
This commit maps all SMP reasons to HCI_ERROR_AUTH_FAILURE, which will
be converted to MGMT_STATUS_AUTH_FAILED in the management layer.
Reported-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Reviewed-by: João Paulo Rechi Vita <jprvita@openbossa.org>
Signed-off-by: Paulo Sérgio <paulo.sergio@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The mgmt_read_index_list uses one loop to calculate the max needed size
of its response with the help of an upper-bound of the controller count.
The second loop is more strict as it checks for HCI_SETUP (which might
have gotten set after the first loop) and could result in some indexes
being skipped. Because of this the function needs to readjust the event
length and index count after filling in the response array.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
If the cipher suites need to be allocated, but this
allocation fails, this leaks the internal scan request.
Fix that by going to the correct error handling label.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sets the sysfs device_type to 'vlan' for udev. This makes it easier for
applications that query network information via udev to identify vlans
instead of using strrchr().
Signed-off-by: Doug Goldstein <cardoe@cardoe.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6431cbc25f(Create a mechanism for upward inetpeer propagation into routes)
introduces these codes, but this mechanism is never enabled since
rt6i_peer_genid always is zero whether it is not assigned or assigned by
rt6_peer_genid(). After 5943634fc5 (ipv4: Maintain redirect and PMTU info
in struct rtable again), the ipv4 related codes of this mechanism has been
removed, I think we maybe able to remove them now.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
x->replay_esn is already checked in if clause,
so remove check and ident properly
Signed-off-by: Ulrich Weber <ulrich.weber@sophos.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
- minimal fixes to the packet layout to avoid the __packed attribute when not
needed
- new packet type called UNICAST_4ADDR: in this packet it is possible to find
both source and destination node (in the classic UNICAST header only the
destination field exists).
- a new feature: Distributed ARP Table (D.A.T.). It aims to reduce ARP lookups
latency by means of a simil-DHT approach.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlCasB8ACgkQpGgxIkP9cwd2kACeOhRvj9EA2hWo1vKQUN6OvTi0
nOcAn08Rvyf+gUPAFQcA9HEUAr8kAebT
=c3ey
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
- minimal fixes to the packet layout to avoid the __packed attribute when not
needed
- new packet type called UNICAST_4ADDR: in this packet it is possible to find
both source and destination node (in the classic UNICAST header only the
destination field exists).
- a new feature: Distributed ARP Table (D.A.T.). It aims to reduce ARP lookups
latency by means of a simil-DHT approach.
The tx data offset of packet mmap tx ring used to be :
(TPACKET2_HDRLEN - sizeof(struct sockaddr_ll))
The problem is that, with SOCK_RAW socket, the payload (14 bytes after
the beginning of the user data) is misaligned.
This patch allows to let the user gives an offset for it's tx data if
he desires.
Set sock option PACKET_TX_HAS_OFF to 1, then specify in each frame of
your tx ring tp_net for SOCK_DGRAM, or tp_mac for SOCK_RAW.
Signed-off-by: Paul Chavent <paul.chavent@onera.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
