AM35x has musb interface (version 1.8) and uses CPPI41 DMA engine.
It has USB phy built inside the IP itself.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Get mem and irq resources using platform helpers
- platform_get_base
- platform_get_irq
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Implement the suggested workaround for OMAP3 regarding to sDMA draining
issue, when the channel is disabled on the fly.
This errata affects the following configuration:
sDMA transfer is source synchronized
Buffering is enabled
SmartStandby is selected.
The issue can be easily reproduced by creating overrun situation while
recording audio.
Either introduce load to the CPU:
nice -19 arecord -D hw:0 -M -B 10000 -F 5000 -f dat > /dev/null & \
dd if=/dev/urandom of=/dev/null
or suspending the arecord, and resuming it:
arecord -D hw:0 -M -B 10000 -F 5000 -f dat > /dev/null
CTRL+Z; fg; CTRL+Z; fg; ...
In case of overrun audio stops DMA, and restarts it (without reseting
the sDMA channel). When we hit this errata in stop case (sDMA drain did
not complete), at the coming start the sDMA will not going to be
operational (it is still draining).
This leads to DMA stall condition.
On OMAP3 we can recover with sDMA channel reset, it has been observed
that by introducing unrelated sDMA activity might also help (reading
from MMC for example).
The same errata exists for OMAP2, where the suggestion is to disable the
buffering to avoid this type of error.
On OMAP3 the suggestion is to set sDMA to NoStandby before disabling
the channel, and wait for the drain to finish, than configure sDMA to
SmartStandby again.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by : Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by : Manjunath Kondaiah G <manjugk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
An errata workaround for omap24xx is not setting the buffering disable bit
25 what is the purpose but channel enable bit 7 instead.
Background for this fix is the DMA stalling issue with ASoC omap-mcbsp
driver. Peter Ujfalusi <peter.ujfalusi@nokia.com> has found an issue in
recording that the DMA stall could happen if there were a buffer overrun
detected by ALSA and the DMA was stopped and restarted due that. This
problem is known to occur on both OMAP2420 and OMAP3. It can recover on
OMAP3 after dma free, dma request and reconfiguration cycle. However, on
OMAP2420 it seems that only way to recover is a reset.
Problem was not visible before the commit c12abc0. That commit changed that
the McBSP transmitter/receiver is released from reset only when needed. That
is, only enabled McBSP transmitter without transmission was able to prevent
this DMA stall problem in receiving side and underlying problem did not show
up until now. McBSP transmitter itself seems to no be reason since DMA
stall does not recover by enabling the transmission after stall.
Debugging showed that there were a DMA write active during DMA stop time and
it never completed even when restarting the DMA. Experimenting showed that
the DMA buffering disable bit could be used to avoid stalling when using
source synchronized transfers. However that could have performance hit and
OMAP3 TRM states that buffering disable is not allowed for destination
synchronized transfers so subsequent patch will implement a method to
complete DMA writes when stopping.
This patch is based on assumtion that complete lock-up on OMAP2420 is
different but related problem. I don't have access to OMAP2420 errata but
I believe this old workaround here is put for a reason but unfortunately
a wrong bit was typed and problem showed up only now.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Manjunath Kondaiah G <manjugk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is just a readability and debugging improvement. As selection bit in
DEVCONF register is cleared when using 96 MHz PRCM source and set when using
external CLKS pin, change definitions to be sync with these.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Only OMAP2+ platforms have the System Control Module (SCM) IP block.
In the past, we've kept the SCM header file in plat-omap. This has
led to abuse - device drivers including it; includes being added that
create implicit dependencies on OMAP2+ builds; etc.
In response, move the SCM headers into mach-omap2/.
As part of this, remove the direct SCM access from the OMAP UDC
driver. It was clearly broken. The UDC code needs an indepth review for
use on OMAP2+ chips.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Previously the OMAP McBSP ASoC driver implemented CLKS switching by
using omap_ctrl_{read,write}l() directly. This is against policy; the OMAP
System Control Module functions are not intended to be exported to drivers.
These symbols are no longer exported, so as a result, the OMAP McBSP ASoC
driver does not build as a module.
Resolve the CLKS clock changing portion of this problem by creating a
clock parent changing function that lives in
arch/arm/mach-omap2/mcbsp.c, and modify the ASoC driver to use it.
Due to the unfortunate way that McBSP support is implemented in ASoC
and the OMAP tree, this symbol must be exported for use by
sound/soc/omap/omap-mcbsp.c.
Going forward, the McBSP device driver should be moved from
arch/arm/*omap* into drivers/ or sound/soc/* and the CPU DAI driver
should be implemented as a platform_driver as many other ASoC CPU DAI
drivers are. These two steps should resolve many of the layering
problems, which will rapidly reappear during a McBSP hwmod/PM runtime
conversions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The OMAP ASoC McBSP code implemented CLKR and FSR signal muxing via
direct System Control Module writes on OMAP2+. This required the
omap_ctrl_{read,write}l() functions to be exported, which is against
policy: the only code that should call those functions directly is
OMAP core code, not device drivers. omap_ctrl_{read,write}*() are no
longer exported, so the driver no longer builds as a module.
Fix the pinmuxing part of the problem by removing calls to
omap_ctrl_{read,write}l() from the OMAP ASoC McBSP code and
implementing signal muxing functions in arch/arm/mach-omap2/mcbsp.c.
Due to the unfortunate way that McBSP support is implemented in ASoC
and the OMAP tree, these symbols must be exported for use by
sound/soc/omap/omap-mcbsp.c.
Going forward, the McBSP device driver should be moved from
arch/arm/*omap* into drivers/ or sound/soc/*, and the CPU DAI driver
should be implemented as a platform_driver as many other ASoC CPU DAI
drivers are. These two steps should resolve many of the layering
problems, which will rapidly reappear during a McBSP hwmod/PM runtime
conversion.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Conform the OMAP2420_CTRL_BASE macro name to the standard of the rest of the
OMAP*_CTRL_BASE macro names. This fixes a bug in the OMAP2420 SCM code that
prevented OMAP242X_CTRL_REGADDR from working.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some modules which have 16bit registers can cause imprecise
aborts if a __raw_readl/writel is used to read/write 32 bits.
Add an additional flag to identify modules which have such
hard requirement, and handle it in the hwmod framework.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP3 IGEP module is a low-power, high performance production-ready
system-on-module (SOM) based on TI's OMAP3 family. More about this
board at www.igep.es.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
[tony@atomide.com: updated for the mmc changes and to be selected by default]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes sparse warnings due non declarations of static functions.
arch/arm/plat-omap/sram.c:130:13: warning: symbol 'omap_detect_sram' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:216:13: warning: symbol 'omap_map_sram' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:450:12: warning: symbol 'omap_sram_init' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:348:12: warning: symbol 'omap242x_sram_init' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:369:12: warning: symbol 'omap243x_sram_init' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:425:12: warning: symbol 'omap34xx_sram_init' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:441:12: warning: symbol 'omap44xx_sram_init' was not declared. Should it be static
arch/arm/plat-omap/mcbsp.c:36:6: warning: symbol 'omap_mcbsp_write' was not declared. Should it be static?
arch/arm/plat-omap/mcbsp.c:50:5: warning: symbol 'omap_mcbsp_read' was not declared. Should it be static?
arch/arm/plat-omap/mcbsp.c:65:6: warning: symbol 'omap_mcbsp_st_write' was not declared. Should it be static?
arch/arm/plat-omap/mcbsp.c:70:5: warning: symbol 'omap_mcbsp_st_read' was not declared. Should it be static?
arch/arm/plat-omap/mcbsp.c:1648:15: warning: symbol 'omap_st_add' was not declared. Should it be static?
arch/arm/plat-omap/fb.c:414:15: warning: symbol 'omapfb_reserve_sram' was not declared. Should it be static?
arch/arm/plat-omap/cpu-omap.c:43:5: warning: symbol 'omap_verify_speed' was not declared. Should it be static?
arch/arm/plat-omap/cpu-omap.c:61:14: warning: symbol 'omap_getspeed' was not declared. Should it be static?
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes sparse warnings due non declarations of static functions.
arch/arm/mach-omap2/timer-gp.c:115:12: warning: symbol 'omap2_gp_clockevent_set_gptimer' was not declared. Should it be static?
arch/arm/mach-omap2/powerdomain.c:993:5: warning: symbol 'pwrdm_set_lowpwrstchange' was not declared. Should it be static?
arch/arm/mach-omap2/board-flash.c:141:8: warning: symbol 'board_nand_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-n8x0.c:416:6: warning: symbol 'n8x0_mmc_slot1_cover_handler' was not declared. Should it be static?
arch/arm/mach-omap2/board-n8x0.c:544:13: warning: symbol 'n8x0_mmc_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-peripherals.c:902:13: warning: symbol 'rx51_peripherals_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-video.c:107:13: warning: symbol 'rx51_video_mem_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-debugboard.c:155:12: warning: symbol 'zoom_debugboard_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-peripherals.c:280:13: warning: symbol 'zoom_peripherals_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-igep0020.c:110:13: warning: symbol 'igep2_flash_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-am3517evm.c:109:6: warning: symbol 'am3517_evm_ethernet_init' was not declared. Should it be static?
drivers/mtd/onenand/omap2.c:577:5: warning: symbol 'omap2_onenand_rephase' was not declared. Should it be static?
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes sparse warnings due to non declaration of
static structures and variables.
Sparse warning logs fixed:
arch/arm/mach-omap2/control.c:88:6: warning: symbol 'omap3_secure_ram_storage' was not declared. Should it be static?
n
arch/arm/mach-omap2/timer-gp.c:50:22: warning: symbol 'gptimer_wakeup' was not declared. Should it be static?
arch/arm/mach-omap2/timer-gp.c:240:18: warning: symbol 'omap_timer' was not declared. Should it be static?
arch/arm/mach-omap2/prcm.c:121:24: warning: symbol 'prcm_context' was not declared. Should it be static?
arch/arm/mach-omap2/mux2420.c:510:29: warning: symbol 'omap2420_pop_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux2430.c:589:29: warning: symbol 'omap2430_pop_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:934:28: warning: symbol 'omap3_cus_subset' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1080:29: warning: symbol 'omap3_cus_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1272:28: warning: symbol 'omap3_cbb_subset' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1393:29: warning: symbol 'omap3_cbb_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1603:28: warning: symbol 'omap36xx_cbp_subset' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1821:29: warning: symbol 'omap36xx_cbp_ball' was not declared. Should it be static?
arch/arm/mach-omap2/pm-debug.c:165:15: warning: symbol 'pm_dbg_dir' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3evm.c:587:30: warning: symbol 'ads7846_config' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3evm.c:606:23: warning: symbol 'omap3evm_spi_board_info' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-sdram.c:46:25: warning: symbol 'rx51_sdrc_params' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-sdram.c:211:25: warning: symbol 'rx51_get_sdram_timings' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3touchbook.c:64:15: warning: symbol 'touchbook_revision' was not declared. Should it be static?
arch/arm/mach-omap2/board-am3517evm.c:350:24: warning: symbol 'am3517_evm_dss_device' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3stalker.c:567:23: warning: symbol 'omap3stalker_spi_board_info' was not declared. Should it be static?
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise tidspbridge cannot work.
It looks like this was dropped in the conversion to staging. I took the
liberty of doing some cleaning up.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A patch from Sukumar Ghorai <s-ghorai@ti.com> changed the
nwires to use caps instead. However, nwires is still
needed for the earlier controller.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
In OMAP4, as per new PM programming model, the legacy registers
which were there in OMAP3 are all shifted by 0x100 while new one's
are added from offset 0 to 0x10.
For OMAP4, the register offset appending of 0x100 done in devices.c
currently, is moved to driver file.This change fits in for current
implementation as well as once the driver undergoes hwmod adaptation.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap4 es2 hsmmc has a updated soft reset logic.After the
reset is issued monitor a 0->1 transition first. The reset of
CMD or DATA lines is complete only after a 0->1->0 transition
of SRC or SRD bits.
Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Tested-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The existing definitions for cpu revision used
upper nibble in the bits[15:08]. With OMAP3630,
definitions use lower nibble.
This patch unifies the definitions to start
at lower nibble.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds driver support for OMAP2/3/4 high speed UART.
The driver is made separate from 8250 driver as we cannot
over load 8250 driver with omap platform specific configuration for
features like DMA, it makes easier to implement features like DMA and
hardware flow control and software flow control configuration with
this driver as required for the omap-platform.
This patch involves only the core driver and its dependent.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Remove set_uart_globals function as this will not be needed as
physical address for uarts will be taken from hwmod data file.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds omap_hwmod data for UARTs on OMAP2 and OMAP3
platforms.
UART4 support for 3630 and OMAP2 hwmod data added by Govindraj R.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Introduce of a generic way to setup smsc911x based Ethernet
controller connected to GPMC similar to gpmc-smc91x but without
timing setup.
Signed-off-by: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding support for LogicPD's OMAP 3530 LV SOM and
OMAP 35x Torpedo board.
Signed-off-by: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch has multiple fixes together. To ensure that git bisect work across
commits, all changes are clubbed together
1. Move the common control base address to control core
2. Remove the manually coeded defines and use the ones from headers.
3. Fix the the status register define in id.c for OMAP4
4. Fix all the register define in hsmmc.c
5. Use the control pad accessor API for omap4 hsmmc register accesses
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP4, control module is divided into 4 separate IPs
- OMAP44XX_CTRL_MODULE_CORE
- OMAP44XX_CTRL_MODULE_PAD_CORE
- OMAP44XX_CTRL_MODULE_WKUP
- OMAP44XX_CTRL_MODULE_PAD_WKUP
This patch adds all the omap4 control module register data and
includes them in the common control.h
The register data is autogenerated from the codebase thanks
to Benoit Cousson efforts
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP4 control pad are not addressable from control
core base. So the common omap_ctrl_read/write APIs breaks
Hence export separate APIs to manage the omap4 pad control
registers.
This APIs will work only for OMAP4
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On omap4 control module is divided in four IP blocks.
- CTRL_MODULE_CORE 0x4a002000
- CTRL_MODULE_PAD_CORE 0x4a100000
- CTRL_MODULE_WKUP 0x4a30c000
- CTRL_MODULE_PAD_WKUP 0x4a31e000
Addressing all the modules with single base address is not possible
considering 16 bit offsets. The mux code manages the pad core and pad
wakeup related base address inside the mux framework. For other usage
only control core and control pad bases are necessary. So this patch
maps only needed pad control base address which is used by device drivers
and infrastructure code
The main control core base is still kept same in this patch to
keep git-bisect working. This will be fixed in the relevant patch
in this series.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DSS on ES2 supports only OSWR, hence remove the support
for CSWR from the powerdomain framework.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
wires variable is renamed, extended and this single variable to be used to
pass the platform capabilities, e.g DDR mode. Also removed the hardcoded
value was using as bus-width.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix this and similar build warnings when building with
omap_4430sdp_defconfig.
CC arch/arm/mach-omap2/board-4430sdp.o
In file included from arch/arm/mach-omap2/board-4430sdp.c:36:
arch/arm/plat-omap/include/plat/usb.h:109: warning: return type defaults to 'int'
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the id.c and cpu.h files to support
omap4 ES2.0 silicon detection. Few initial omap4 es2 samples
IDCODE is same as es1. So the patch uses ARM cpuid register to
detect the ES version for such samples
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The current version contains only the interconnects and the
mpu hwmods.
The remaining hwmods will be introduced by further patches on
top of this one.
- enable as well omap_hwmod.c build for OMAP4 Soc
Please not that this file uses the new naming convention for
naming HW IPs. This convention will be backported soon for previous
OMAP2 & 3 data files.
new name trm name
------------- -------------------
counter_32k synctimer_32k
l3_main l3
timerX gptimerX / dmtimerX
mmcX mmchsX / sdmmcX
dma_system sdma
smartreflex_X sr_X / sr?
usb_host_fs usbfshost
usb_otg_hs hsusbotg
usb_tll_hs usbtllhs_config
wd_timerX wdtimerX
ipu cortexm3 / ducati
dsp c6x / tesla
iva ivahd / iva2.2
kbd kbdocp / keyboard
mailbox system_mailbox
mpu cortexa9 / chiron
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
In order to help differentiate omap_devices from normal
platform_devices, make them all a parent of a new common parent
device.
Then, in order to determine if a platform_device is also an
omap_device, checking the parent is all that is needed.
Users of this feature are the runtime PM core for OMAP, where we need
to know if a device being passed in is an omap_device or not in order
to know whether to call the omap_device API with it.
In addition, all omap_devices will now show up under /sys/devices/omap
instead of /sys/devices/platform
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This reverts commit 0007122ad8.
The dereference method of checking for a valid omap_device when
wrapping a platform_device is rather unsafe and dangerous.
Instead, a better way of checking for a valid omap-device is
to use a common parent device for all omap_devices, then a check
can simply be made using the device parent. The only user of this
API was the initial version of the runtime PM core for OMAP. This
has now been switched to check device parent, so there are no more
users of this API.
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP4 has an iva device and a dsp devcice where as OMAP2/3
has only an iva device. In this file the iva device in the
system is registered under the name dsp_dev and the API
to retrieve the iva device is omap2_get_dsp_device.
This patch renames the dsp_dev to iva_dev, renames
omap2_get_dsp_device to omap2_get_iva_device,
registers dsp_dev for OMAP4 and adds a new API
omap4_get_dsp_device to retrieve the dep_dev.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch:
- adds more documentation to the hwmod code
- fixes some documentation typos elsewhere in the file
- changes the _sysc_*() function names to appear in (verb, noun) order,
to match the rest of the function names.
This patch should not result in any functional change.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Some modules (like GPIO, DSS...) require optionals clock to be enabled
in order to complete the sofreset properly.
Add a HWMOD_CONTROL_OPT_CLKS_IN_RESET flag to force all optional clocks
to be enabled before reset. Disabled them once the reset is done.
TODO:
For the moment it is very hard to understand from the HW spec, which
optional clock is needed and which one is not. So the current approach
will enable all the optional clocks.
Paul proposed a much finer approach that will allow to tag only the needed
clock in the optional clock table. This might be doable as soon as we have
a clear understanding of these dependencies.
Reported-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
In OMAP3 a specific SYSSTATUS register was used to get the softreset status.
Starting in OMAP4, some IPs does not have SYSSTATUS register and instead
use the SYSC softreset bit to provide the status.
Other cases might exist:
- Some IPs like McBSP does have a softreset control but no reset status.
- Some IPs that represent subsystem, like the DSS, can contains
a reset status without softreset control. The status is the aggregation
of all the sub modules reset status.
- Add a new flag (SYSC_HAS_RESET_STATUS) to identify the new programming model
and replace the previous SYSS_MISSING, that was used to flag IP with
softreset control but without the SYSSTATUS register, with a specific
SYSS_HAS_RESET_STATUS flag.
- MCSPI and MMC contains both programming models, so the legacy one
will be prevented by removing the syss offset field that become useless.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Expose an hardreset API from hwmod in order to assert / deassert all the
individual reset lines that belong to an hwmod. This API is needed by
some of the more complicated processor drivers, e.g., DSP/Bridge,
Syslink, etc.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
