Fix the "pciehp probing slow" problem reported from Jan C. Nordholz in
http://bugzilla.kernel.org/show_bug.cgi?id=10751.
The command completed bit in Slot Status register applies only to
commands issued to control the attention indicator, power indicator,
power controller, or electromechanical interlock. However, writes to
other parts of the Slot Control register would end up writing to the
control fields. Hence, any write to Slot Control register is
considered as a command. However, if the controller doesn't support
any of attention indicator, power indicator, power controller and
electromechanical interlock, command completed bit would not set in
writing to Slot Control register. In this case, we should not wait for
command completed bit set, otherwise all commands would be considered
not completed in timeout seconds (1 sec.).
The cause of the problem is pciehp driver didn't take this situation
into account. This patch changes pciehp to take it into account. This
patch also add the check for "No Command Completed Support" bit in
Slot Capability register. If it is set, we should not wait for command
completed bit set as well.
This problem seems to be revealed by the commit
c27fb883df that fixed the bug that
pciehp did not wait for command completed properly (pciehp just
ignored the command completion event).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some (broken?) platform assign the same slot name to multiple hotplug
slots. On such system, slot initialization would fail because of name
collision. The shpchp driver already have a "slot_with_bus" module
option which adds the bus number into the slot name. This patch adds
the message about this module option that will be displayed when slot
name collision is detected.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Problem: An application violating the architectural rules regarding
operation dependencies and having specific Register Stack Engine (RSE)
state at the time of the violation, may result in an illegal operation
fault and invalid RSE state. Such faults may initiate a cascade of
repeated illegal operation faults within OS interruption handlers.
The specific behavior is OS dependent.
Implication: An application causing an illegal operation fault with
specific RSE state may result in a series of illegal operation faults
and an eventual OS stack overflow condition.
Workaround: OS interruption handlers that switch to kernel backing
store implement a check for invalid RSE state to avoid the series
of illegal operation faults.
The core of the workaround is the RSE_WORKAROUND code sequence
inserted into each invocation of the SAVE_MIN_WITH_COVER and
SAVE_MIN_WITH_COVER_R19 macros. This sequence includes hard-coded
constants that depend on the number of stacked physical registers
being 96. The rest of this patch consists of code to disable this
workaround should this not be the case (with the presumption that
if a future Itanium processor increases the number of registers, it
would also remove the need for this patch).
Move the start of the RBS up to a mod32 boundary to avoid some
corner cases.
The dispatch_illegal_op_fault code outgrew the spot it was
squatting in when built with this patch and CONFIG_VIRT_CPU_ACCOUNTING=y
Move it out to the end of the ivt.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Some versions of the Virtual I/O Server on Power
return 0x99 in the non-SCSI error status field as success,
rather than 0. This fixes the ibmvscsi driver to treat this
response as success.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Following a hard reset of a SAS raid, one of the raid targets is occasionally
missing. I tracked this down to a pretty obscure little bug.
The LSI fusion drivers for SAS and Fibre Channel both use their respective
transport layers. Those transport layers increment the target number
assigned to new targets.
The routine __scsi_scan_target uses the "this_id" element of the Scsi_Host
structure to avoid scanning the scsi host adapter. Both fusion drivers set
"this_id" from a value returned in a firmware PortFacts response. For my
particular test case (SAS) the firmware id assigned to the initiator was
173. After enough raid resets to cause the raid targets to go and come a
sufficient number of times, the id assigned by the transport to a raid
target would match the id assigned by the host adapter to the "this_id"
field, resulting in that target not being scanned.
Fix by not assigning this_id and not checking it in slave_configure.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There's a reason why using C99 initialisers even in the supposedly
trivial structs is a good idea.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The identification of this bug is thanks to Cheng Wei and Tomasz
Grobelny.
To avoid divide-by-zero, the implementation previously ignored RTTs
smaller than 4 microseconds when performing integer division RTT/4.
When the RTT reached a value less than 4 microseconds (as observed on
loopback), this prevented the Window Counter CCVal value from
advancing. As a result, the receiver stopped sending feedback. This in
turn caused non-ending expiries of the nofeedback timer at the sender,
so that the sending rate was progressively reduced until reaching the
minimum of one packet per 64 seconds.
The patch fixes this bug by handling integer division more
intelligently. Due to consistent use of dccp_sample_rtt(),
divide-by-zero-RTT is avoided.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC4340 said:
8.5. Pseudocode
...
If P.type is not Data, Ack, or DataAck and P.X == 0 (the packet
has short sequence numbers), drop packet and return
But DCCP has some mistake to handle short sequence numbers packet, now
it drop packet only if P.type is Data, Ack, or DataAck and P.X == 0.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the AP7 cpufreq init to late_initcall() so that we don't try to
bring up cpufreq until the governor is ready. x86 also uses
late_initcall() for this.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The chip phy_init() function must be called before the dig_enable() function
but dig_enable() is called when the device is opened and we only call
phy_init() after having reigstered the device, meaning the two can race.
Fix this by doing the phy_init() before we register the input device.
Thanks to Rodolfo Giometti <giometti@enneenne.com> for the report.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix driver name - thanks to Guennadi Liakhovetski <g.liakhovetski@gmx.de> for
reporting this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
phys is displayed in diagnostic output like that from evbug so ensure
that it is set to something.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Also do not fail i8042 entire initialization if enabling dritek extension
fails.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add Chien and remove Nishi from maintainers list for NetEffect.
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The driver supports a few features (RNR NAK, port active event, SRQ
resize) that were not reported in the device capability flags. This
patch fixes that.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Gabriel C <nix.or.die@googlemail.com> pointed out that when the x86
bitops are updated to operate on unsigned long, the code in
sdma_abort_task() will produce warnings:
drivers/infiniband/hw/ipath/ipath_sdma.c: In function 'sdma_abort_task':
drivers/infiniband/hw/ipath/ipath_sdma.c:267: warning: passing argument 2 of 'constant_test_bit' from incompatible pointer type
and so on, because it uses test_bit() to operation on a u64 value
(returned by ipath_read_kref64() for a hardware register).
Fix up these warnings by converting the test_bit() operations to &ing
with appropriate symbolic defines of the bits within the hardware
register. This has the benign side-effect of making the code more
self-documenting as well.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Based on Roland's patch. This approach was suggested by Austin Clements
from the very beginning, and then by Linus.
As Austin pointed out, the execing task can be killed by SI_TIMER signal
because exec flushes the signal handlers, but doesn't discard the pending
signals generated by posix timers. Perhaps not a bug, but people find this
surprising. See http://bugzilla.kernel.org/show_bug.cgi?id=10460
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Austin Clements <amdragon+kernelbugzilla@mit.edu>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently sigqueue_free() removes sigqueue from list, but doesn't cancel the
pending signal. This is not consistent, the task should either receive the
"full" signal along with siginfo_t, or it shouldn't receive the signal at all.
Change sigqueue_free() to clear SIGQUEUE_PREALLOC but leave sigqueue on list
if it is queued.
This is a user-visible change. If the signal is blocked, it stays queued
after sys_timer_delete() until unblocked with the "stale" si_code/si_value,
and of course it is still counted wrt RLIMIT_SIGPENDING which also limits
the number of posix timers.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Austin Clements <amdragon+kernelbugzilla@mit.edu>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.26:
sh: Drop broken URAM support on SH7723.
sh: update Migo-R defconfig
sh: use sm501 8250 mfd support on r2d boards
sh: add probe support for new sh7723 cut
sh: fix VPU interrupt vector for sh7723
sh: fix USBF resource for sh7722
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (52 commits)
vlan: Use bitmask of feature flags instead of seperate feature bits
fmvj18x_cs: add NextCom NC5310 rev B support
xirc2ps_cs: re-initialize the multicast address in do_reset
3C509: rx_bytes should not be increased when alloc_skb failed
NETFRONT: Use __skb_queue_purge()
VIRTIO: Use __skb_queue_purge()
phylib: do EXPORT_SYMBOL on get_phy_id
netlink: Fix nla_parse_nested_compat() to call nla_parse() directly
WAN: protect HDLC proto list while insmod/rmmod
drivers/net/fs_enet: remove null pointer dereference
S2io: Version update for napi and MSI-X patches
S2io: Added napi support when MSIX is enabled.
S2io: Move all the transmit completions to a single msi-x (alarm) vector
drivers/net/ehea - remove unnecessary memset after kzalloc
au1000_eth: remove useless check
Blackfin EMAC Driver: Removed duplicated include <linux/ethtool.h>
cpmac bugfixes and enhancements
e1000e: use resource_size_t, not unsigned long, for phys addrs
net/usb: add support for Apple USB Ethernet Adapter
uli526x: add support for netpoll
...
I can't think of any valid reason for ext4 to not use barriers when
they are available; I believe this is necessary for filesystem
integrity in the face of a volatile write cache on storage.
An administrator who trusts that the cache is sufficiently battery-
backed (and power supplies are sufficiently redundant, etc...)
can always turn it back off again.
SuSE has carried such a patch for ext3 for quite some time now.
Also document the mount option while we're at it.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
If the device doesn't support write barriers, the write is retried
without ordered mode. But the buffer head needs to be re-locked or
submit_bh will fail with on BUG(!buffer_locked(bh)).
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
If a journal checksum error is detected, the ext4 filesystem will call
ext4_error(), and the mount will either continue, become a read-only
mount, or cause a kernel panic based on the superblock flags
indicating the user's preference of what to do in case of filesystem
corruption being detected.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
There is a bug when we are trying to verify that the reserve inode's
double indirect blocks point back to the primary gdt blocks. The fix is
obvious, we need to mod the gdb count by the addr's per block. This was
verified using the same testcase as with the ext3 equivalent of this
patch.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
With FLEX_BG block bitmaps, inode bitmaps and inode tables _MAY_ be
allocated outside the group. So, when initializing an uninitialized
block bitmap, we need to check the location of this blocks before
setting the corresponding bits in the block bitmap of the newly
initialized group. Also return the right number of free blocks when
counting the available free blocks in uninit group.
Tested-by: Aneesh Kumar K.V <aneesh.kumar@inux.vnet.ibm.com>
Signed-off-by: Jose R. Santos <jrs@us.ibm.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Fix use of uninitialized data with debug enabled.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Align i2c_device_id.driver_data to 8 bytes to not fail on crossbuilds.
(Added in d2653e92732bd3911feff6bee5e23dbf959381db.)
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The tuner driver used to change i2c_client.name for its own needs, but
it really shouldn't, as this field is used by i2c-core to do the
device/driver matching. So, create and use a separate field for the
tuner driver needs.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Just provide reasonable defaults for the new stuff. Tickless and
hrtimers are turned on for all boards except ATSTK1004.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
global_reg_snapshot shouldn't be visible in our userspace headers.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was copied over from the previous MobileR bits, which doesn't
apply to R2. The URAM block on R2 is recycled for the L2 instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
Kconfig: introduce ARCH_DEFCONFIG to DEFCONFIG_LIST
.gitignore: match ncscope.out
scripts/ver_linux use 'gcc -dumpversion'
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] Add ICH9DO into the iTCO_wdt.c driver
[WATCHDOG] Fix booke_wdt.c on MPC85xx SMP system's
[WATCHDOG] Add a watchdog driver based on the CS5535/CS5536 MFGPT timers
[WATCHDOG] hpwdt: Fix NMI handling.
[WATCHDOG] Blackfin Watchdog Driver: split platform device/driver
[WATCHDOG] Add w83697h_wdt early_disable option
[WATCHDOG] Make w83697h_wdt timeout option string similar to others
[WATCHDOG] Make w83697h_wdt void-like functions void
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
[ALSA] hda - Fix capture mute Widget for stac9250/9251
[ALSA] snd-pcsp - fix pcsp_treble_info() to honour an item number
[ALSA] hda - Added support for Foxconn P35AX-S mainboard
[ALSA] hda - Fix COEF and EAPD in ALC889 auto-configuration mode
[ALSA] hda - Fix noise on VT1708 codec
[ALSA] hda - Add model for ASUS P5K-E/WIFI-AP
init/Kconfig contains a list of configs that are searched
for if 'make *config' are used with no .config present.
Extend this list to look at the config identified by
ARCH_DEFCONFIG.
With this change we now try the defconfig targets last.
This fixes a regression reported
by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
