When transitioning into ERROR state, the QP was getting flushed after
waking up any waiters. This can cause applications to miss flushed work
requests which can stall an NFS mount.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
T4/T5 hardware can't handle MRs >= 8GB due to a hardware bug. So limit
registrations to < 8GB for thse devices.
Based on original work by Steve Wise <swise@opengridcomputing.com>.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
0B MRs need some tweaks to work correctly with HW. When writing the
TPTE, if the MR length is zero we now:
1) turn off all permissions
2) set the length to -1
While functionality/capabilities of the MR are the same with these
changes, it resolves a dapltest 0B RDMA Read test failure. Based on
original work by Steve Wise <swise@opengridcomputing.com>.
Signed-off-by: Pramod Kumar <pramod@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Address resolution always does a context switch to a work-queue to
deliver the address resolution event. When the IP address is already
cached in the system ARP table, we're going through the following:
chain:
rdma_resolve_ip --> addr_resolve (cache hit) -->
which ends up with:
queue_req --> set_timeout (now) --> mod_delayed_work(,, delay=1)
We actually do realize that the timeout should be zero, but the code
forces it to a minimum of one jiffie.
Using one jiffie as the minimum delay value results in sub-optimal
scheduling of executing this work item by the workqueue, which on the
below testbed costs about 3-4ms out of 12ms total time.
To fix that, we let the minimum delay to be zero. Note that the
connect step times change too, as there are address resolution calls
from that flow.
The results were taken from running both client and server on the
same node, over mlx4 RoCE port.
before -->
step total ms max ms min us us / conn
create id : 0.01 0.01 6.00 6.00
resolve addr : 4.02 4.01 4013.00 4016.00
resolve route: 0.18 0.18 182.00 183.00
create qp : 1.15 1.15 1150.00 1150.00
connect : 6.73 6.73 6730.00 6731.00
disconnect : 0.55 0.55 549.00 550.00
destroy : 0.01 0.01 9.00 9.00
after -->
step total ms max ms min us us / conn
create id : 0.01 0.01 6.00 6.00
resolve addr : 0.05 0.05 49.00 52.00
resolve route: 0.21 0.21 207.00 208.00
create qp : 1.10 1.10 1104.00 1104.00
connect : 1.22 1.22 1220.00 1221.00
disconnect : 0.71 0.71 713.00 713.00
destroy : 0.01 0.01 9.00 9.00
Signed-off-by: Or Kehati <ork@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Applications can request that the SM assign an MGID by passing a mcast
member request containing MGID = 0. When the SM responds by sending
the allocated MGID, this MGID replaces the 0-MGID in the multicast group.
However, the MGID field in the group is also the key field in the IB
core multicast code rbtree containing the multicast groups for the
port.
Since this is a key field, correct handling requires that the group
entry be deleted from the rbtree and then re-inserted with the new
key, so that the table structure is properly maintained.
The current code does not do this correctly. Correct operation
requires that if the key-field gid has changed at all, it should be
deleted and re-inserted.
Note that when inserting, if the new MGID is zero (not the case here
but the code should handle this correctly), we allow duplicate entries
for 0-MGIDs.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
For RoCE, resolution of layer 2 address attributes forces no VLAN if
link-local GIDs are used. This patch allows applications to choose
the VLAN ID for link-local based RoCE GIDs by setting IB_QP_VID in
their QP attribute mask, and prevents the core from overriding this
choice.
Cc: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
CC [M] drivers/infiniband/ulp/isert/ib_isert.o
drivers/infiniband/ulp/isert/ib_isert.c: In function ‘isert_cq_comp_err’:
drivers/infiniband/ulp/isert/ib_isert.c:1979:42: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
- Fall-through in switch case instead in do_control_comp.
- Move rkey invalidation to a function.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
debug_level 1 (warn): Include warning messages.
debug_level 2 (info): Include relevant info for control plane.
debug_level 3 (debug): Include relevant info in the IO path.
Also, added/removed some logging messages.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Personal preference, easier control of the log level with
a single modparam which can be changed dynamically. Allows
better saparation of control and IO plains.
Replaced throughout ib_isert.c:
s/pr_debug/isert_dbg/g
s/pr_info/isert_info/g
s/pr_warn/isert_warn/g
s/pr_err/isert_err/g
Plus nit checkpatch warning change.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We don't want to wait for conn_logout_comp from isert_comp_wq
context as this blocks further completions from being processed.
Instead we wait for it conditionally (if logout response was
actually posted) in wait_conn. This wait should normally happen
immediately as it occurs after we consumed all the completions
(including flush errors) and conn_logout_comp should have been
completed.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Might result in a deadlock where completion context waits for
session commands release where the later might need a final
completion for it.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In order to reduce the contention on CQ locking (present
in some LLDDs) we poll in batches of 16 work completion items.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case the CQ is packed with completions, we can't just
hog the CPU forever. Poll until a sufficient budget (currently
hard-coded to 64k completions) and if budget is exhausted, bailout
and give a chance to other threads.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In order to know that we consumed all the connection completions
we maintain atomic post_send_buf_count for each IO post send. But
we can know that if we post a "beacon" (zero length RECV work request)
after we move the QP into error state and the target does not serve
any new IO. When we consume it, we know we finished all the connection
completion and we can go ahead and destroy stuff.
In error completion handler we now just need to check for ISERT_BEACON_WRID
to arrive and then wait for session commands to cleanup and complete
conn_wait_comp_err.
We reserve another CQ and QP entries to fit the zero length post recv.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We are calling session reinstatement, wait_conn will start
connection termination.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Using TX and RX CQs attached to the same vector might
create a throttling effect coming from the serial processing
of a work-queue. Use one CQ instead, it will do better in interrupt
processing and it provides a simpler code. Also, We get rid of
redundant isert_rx_wq.
Next we can remove the atomic post_send_buf_count from the IO path.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
A pre-step before going to a single CQ.
Also this makes the code a little more simple to
read.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Nit, uintptr_t is designed for pointer casting, use it.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
As a pre-step to a single CQ, we unite the error completion
handlers to a single handler.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It is disabled at the moment, we will get that back
in once the target is more stable.
This reverts commit 95b60f0
"Add support for completion interrupt coalescing"
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Currently we have no way to tell that the target stack is in shutdown
sequence. In case we have open connections, the initiator immediately
attempts to reconnect in a DDOS attack style, so we may end up
terminating the iser enabled network portal while it's np_accept_list
still have pending connections.
The workaround is simply release all the connections in the list.
A proper fix will be to start shutdown sequence by shutting the
network portal to avoid initiator immediate reconnect attempts.
But the temporary work around seems to work at this point, so I think
we can do this for now...
Reported-by: Slava Shwartsman <valyushash@gmail.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
iSER will report supported protection operations based on
the tpg attribute t10_pi settings and HCA PI offload capabilities.
If the HCA does not support PI offload or tpg attribute t10_pi is
not set, we fall to SW PI mode.
In order to do that, we move iscsit_get_sup_prot_ops after connection
tpg assignment.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fallback to software mode DIF if HCA does not support
PI (without crashing obviously). It is still possible to
run with backend protection and an unprotected frontend,
so looking at the command prot_op is not enough. Check
device PI capability on a per-IO basis (isert_prot_cmd
inline static) to determine if we need to handle protection
information.
Trace:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
IP: [<ffffffffa037f8b1>] isert_reg_sig_mr+0x351/0x3b0 [ib_isert]
Call Trace:
[<ffffffff812b003a>] ? swiotlb_map_sg_attrs+0x7a/0x130
[<ffffffffa038184d>] isert_reg_rdma+0x2fd/0x370 [ib_isert]
[<ffffffff8108f2ec>] ? idle_balance+0x6c/0x2c0
[<ffffffffa0382b68>] isert_put_datain+0x68/0x210 [ib_isert]
[<ffffffffa02acf5b>] lio_queue_data_in+0x2b/0x30 [iscsi_target_mod]
[<ffffffffa02306eb>] target_complete_ok_work+0x21b/0x310 [target_core_mod]
[<ffffffff8106ece2>] process_one_work+0x182/0x3b0
[<ffffffff8106fda0>] worker_thread+0x120/0x3c0
[<ffffffff8106fc80>] ? maybe_create_worker+0x190/0x190
[<ffffffff8107594e>] kthread+0xce/0xf0
[<ffffffff81075880>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff8159a22c>] ret_from_fork+0x7c/0xb0
[<ffffffff81075880>] ? kthread_freezable_should_stop+0x70/0x70
Reported-by: Slava Shwartsman <valyushash@gmail.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts to allocate PI contexts dynamically in order
avoid a potentially bogus np->tpg_np and associated NULL pointer
dereference in isert_connect_request() during iser-target endpoint
shutdown with multiple network portals.
Also, there is really no need to allocate these at connection
establishment since it is not guaranteed that all the IOs on
that connection will be to a PI formatted device.
We can do it in a lazy fashion so the initial burst will have a
transient slow down, but very fast all IOs will allocate a PI
context.
Squashed:
iser-target: Centralize PI context handling code
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In situations such as bond failover, The new session establishment
implicitly invokes the termination of the old connection.
So, we don't want to wait for the old connection wait_conn to completely
terminate before we accept the new connection and post a login response.
The solution is to deffer the comp_wait completion and the conn_put to
a work so wait_conn will effectively be non-blocking (flush errors are
assumed to come very fast).
We allocate isert_release_wq with WQ_UNBOUND and WQ_UNBOUND_MAX_ACTIVE
to spread the concurrency of release works.
Reported-by: Slava Shwartsman <valyushash@gmail.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The np listener cm_id will also get ADDR_CHANGE event
upcall (in case it is bound to a specific IP). Handle
it correctly by creating a new cm_id and implicitly
destroy the old one.
Since this is the second event a listener np cm_id may
encounter, we move the np cm_id event handling to a
routine.
Squashed:
iser-target: Move cma_id setup to a function
Reported-by: Slava Shwartsman <valyushash@gmail.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Take isert_conn pointer from cm_id->qp->qp_context. This
will allow us to know that the cm_id context is always
the network portal. This will make the cm_id event check
(connection or network portal) more reliable.
In order to avoid a NULL dereference in cma_id->qp->qp_context
we destroy the qp after we destroy the cm_id (and make the
dereference safe). session stablishment/teardown sequences
can happen in parallel, we should take into account that
connected_handler might race with connection teardown flow.
Also, protect isert_conn->conn_device->active_qps decrement
within the error patch during QP creation failure and the
normal teardown path in isert_connect_release().
Squashed:
iser-target: Decrement completion context active_qps in error flow
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There is no point in accepting a new CM request only
when we are completely done with the last iscsi login.
Instead we accept immediately, this will also cause the
CM connection to reach connected state and the initiator
is allowed to send the first login. We mark that we got
the initial login and let iscsi layer pick it up when it
gets there.
This reduces the parallel login sequence by a factor of
more then 4 (and more for multi-login) and also prevents
the initiator (who does all logins in parallel) from
giving up on login timeout expiration.
In order to support multiple login requests sequence (CHAP)
we call isert_rx_login_req from isert_rx_completion insead
of letting isert_get_login_rx call it.
Squashed:
iser-target: Use kref_get_unless_zero in connected_handler
iser-target: Acquire conn_mutex when changing connection state
iser-target: Reject connect request in failure path
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
ISER_CONN_UP state is not sufficient to know if
we should wait for completion of flush errors and
disconnected_handler event.
Instead, split it to 2 states:
- ISER_CONN_UP: Got to CM connected phase, This state
indicates that we need to wait for a CM disconnect
event before going to teardown.
- ISER_CONN_FULL_FEATURE: Got to full feature phase
after we posted login response, This state indicates
that we posted recv buffers and we need to wait for
flush completions before going to teardown.
Also avoid deffering disconnected handler to a work,
and handle it within disconnected handler.
More work here is needed to handle DEVICE_REMOVAL event
correctly (cleanup all resources).
Squashed:
iser-target: Don't deffer disconnected handler to a work
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Since commit 0fc4ea701f ("Target/iser: Don't put isert_conn inside
disconnected handler") we put the conn kref in isert_wait_conn, so we
need .wait_conn to be invoked also in the error path.
Introduce call to isert_conn_terminate (called under lock)
which transitions the connection state to TERMINATING and calls
rdma_disconnect. If the state is already teminating, just bail
out back (temination started).
Also, make sure to destroy the connection when getting a connect
error event if didn't get to connected (state UP). Same for the
handling of REJECTED and UNREACHABLE cma events.
Squashed:
iscsi-target: Add call to wait_conn in establishment error flow
Reported-by: Slava Shwartsman <valyushash@gmail.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull networking updates from David Miller:
1) New offloading infrastructure and example 'rocker' driver for
offloading of switching and routing to hardware.
This work was done by a large group of dedicated individuals, not
limited to: Scott Feldman, Jiri Pirko, Thomas Graf, John Fastabend,
Jamal Hadi Salim, Andy Gospodarek, Florian Fainelli, Roopa Prabhu
2) Start making the networking operate on IOV iterators instead of
modifying iov objects in-situ during transfers. Thanks to Al Viro
and Herbert Xu.
3) A set of new netlink interfaces for the TIPC stack, from Richard
Alpe.
4) Remove unnecessary looping during ipv6 routing lookups, from Martin
KaFai Lau.
5) Add PAUSE frame generation support to gianfar driver, from Matei
Pavaluca.
6) Allow for larger reordering levels in TCP, which are easily
achievable in the real world right now, from Eric Dumazet.
7) Add a variable of napi_schedule that doesn't need to disable cpu
interrupts, from Eric Dumazet.
8) Use a doubly linked list to optimize neigh_parms_release(), from
Nicolas Dichtel.
9) Various enhancements to the kernel BPF verifier, and allow eBPF
programs to actually be attached to sockets. From Alexei
Starovoitov.
10) Support TSO/LSO in sunvnet driver, from David L Stevens.
11) Allow controlling ECN usage via routing metrics, from Florian
Westphal.
12) Remote checksum offload, from Tom Herbert.
13) Add split-header receive, BQL, and xmit_more support to amd-xgbe
driver, from Thomas Lendacky.
14) Add MPLS support to openvswitch, from Simon Horman.
15) Support wildcard tunnel endpoints in ipv6 tunnels, from Steffen
Klassert.
16) Do gro flushes on a per-device basis using a timer, from Eric
Dumazet. This tries to resolve the conflicting goals between the
desired handling of bulk vs. RPC-like traffic.
17) Allow userspace to ask for the CPU upon what a packet was
received/steered, via SO_INCOMING_CPU. From Eric Dumazet.
18) Limit GSO packets to half the current congestion window, from Eric
Dumazet.
19) Add a generic helper so that all drivers set their RSS keys in a
consistent way, from Eric Dumazet.
20) Add xmit_more support to enic driver, from Govindarajulu
Varadarajan.
21) Add VLAN packet scheduler action, from Jiri Pirko.
22) Support configurable RSS hash functions via ethtool, from Eyal
Perry.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1820 commits)
Fix race condition between vxlan_sock_add and vxlan_sock_release
net/macb: fix compilation warning for print_hex_dump() called with skb->mac_header
net/mlx4: Add support for A0 steering
net/mlx4: Refactor QUERY_PORT
net/mlx4_core: Add explicit error message when rule doesn't meet configuration
net/mlx4: Add A0 hybrid steering
net/mlx4: Add mlx4_bitmap zone allocator
net/mlx4: Add a check if there are too many reserved QPs
net/mlx4: Change QP allocation scheme
net/mlx4_core: Use tasklet for user-space CQ completion events
net/mlx4_core: Mask out host side virtualization features for guests
net/mlx4_en: Set csum level for encapsulated packets
be2net: Export tunnel offloads only when a VxLAN tunnel is created
gianfar: Fix dma check map error when DMA_API_DEBUG is enabled
cxgb4/csiostor: Don't use MASTER_MUST for fw_hello call
net: fec: only enable mdio interrupt before phy device link up
net: fec: clear all interrupt events to support i.MX6SX
net: fec: reset fep link status in suspend function
net: sock: fix access via invalid file descriptor
net: introduce helper macro for_each_cmsghdr
...
A0 hybrid steering is a form of high performance flow steering.
By using this mode, mlx4 cards use a fast limited table based steering,
in order to enable fast steering of unicast packets to a QP.
In order to implement A0 hybrid steering we allocate resources
from different zones:
(1) General range
(2) Special MAC-assigned QPs [RSS, Raw-Ethernet] each has its own region.
When we create a rss QP or a raw ethernet (A0 steerable and BF ready) QP,
we try hard to allocate the QP from range (2). Otherwise, we try hard not
to allocate from this range. However, when the system is pushed to its
limits and one needs every resource, the allocator uses every region it can.
Meaning, when we run out of raw-eth qps, the allocator allocates from the
general range (and the special-A0 area is no longer active). If we run out
of RSS qps, the mechanism tries to allocate from the raw-eth QP zone. If that
is also exhausted, the allocator will allocate from the general range
(and the A0 region is no longer active).
Note that if a raw-eth qp is allocated from the general range, it attempts
to allocate the range such that bits 6 and 7 (blueflame bits) in the
QP number are not set.
When the feature is used in SRIOV, the VF has to notify the PF what
kind of QP attributes it needs. In order to do that, along with the
"Eth QP blueflame" bit, we reserve a new "A0 steerable QP". According
to the combination of these bits, the PF tries to allocate a suitable QP.
In order to maintain backward compatibility (with older PFs), the PF
notifies which QP attributes it supports via QUERY_FUNC_CAP command.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using BF (Blue-Flame), the QPN overrides the VLAN, CV, and SV fields
in the WQE. Thus, BF may only be used for QPNs with bits 6,7 unset.
The current Ethernet driver code reserves a Tx QP range with 256b alignment.
This is wrong because if there are more than 64 Tx QPs in use,
QPNs >= base + 65 will have bits 6/7 set.
This problem is not specific for the Ethernet driver, any entity that
tries to reserve more than 64 BF-enabled QPs should fail. Also, using
ranges is not necessary here and is wasteful.
The new mechanism introduced here will support reservation for
"Eth QPs eligible for BF" for all drivers: bare-metal, multi-PF, and VFs
(when hypervisors support WC in VMs). The flow we use is:
1. In mlx4_en, allocate Tx QPs one by one instead of a range allocation,
and request "BF enabled QPs" if BF is supported for the function
2. In the ALLOC_RES FW command, change param1 to:
a. param1[23:0] - number of QPs
b. param1[31-24] - flags controlling QPs reservation
Bit 31 refers to Eth blueflame supported QPs. Those QPs must have
bits 6 and 7 unset in order to be used in Ethernet.
Bits 24-30 of the flags are currently reserved.
When a function tries to allocate a QP, it states the required attributes
for this QP. Those attributes are considered "best-effort". If an attribute,
such as Ethernet BF enabled QP, is a must-have attribute, the function has
to check that attribute is supported before trying to do the allocation.
In a lower layer of the code, mlx4_qp_reserve_range masks out the bits
which are unsupported. If SRIOV is used, the PF validates those attributes
and masks out unsupported attributes as well. In order to notify VFs which
attributes are supported, the VF uses QUERY_FUNC_CAP command. This command's
mailbox is filled by the PF, which notifies which QP allocation attributes
it supports.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, we've fired all our completion callbacks straight from our ISR.
Some of those callbacks were lightweight (for example, mlx4_en's and
IPoIB napi callbacks), but some of them did more work (for example,
the user-space RDMA stack uverbs' completion handler). Besides that,
doing more than the minimal work in ISR is generally considered wrong,
it could even lead to a hard lockup of the system. Since when a lot
of completion events are generated by the hardware, the loop over those
events could be so long, that we'll get into a hard lockup by the system
watchdog.
In order to avoid that, add a new way of invoking completion events
callbacks. In the interrupt itself, we add the CQs which receive completion
event to a per-EQ list and schedule a tasklet. In the tasklet context
we loop over all the CQs in the list and invoke the user callback.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If mlx5_core_create_mkey fails, decrease the pending counter to undo the
previous increment.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add required __acquire/__release statements to balance spinlock usage.
2. Change the index parameter of begin_wqe() to be unsigned to match supplied
argument type.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/scsi/scsi_debug.c
Agreed and tested resolution to a merge problem between a fix in scsi_debug
and a driver update
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For SPI drivers use the message definitions from scsi.h, and for target
drivers introduce a new TCM_*_TAG namespace.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com
Since we got rid of ordered tag support in 2010 the prime use case of
switching on and off ordered tags has been obsolete. The other function
of enabling/disabling tagging entirely has only been correctly implemented
by the 53c700 driver and isn't generally useful.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Drop the now unused reason argument from the ->change_queue_depth method.
Also add a return value to scsi_adjust_queue_depth, and rename it to
scsi_change_queue_depth now that it can be used as the default
->change_queue_depth implementation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
We won't ever queue more commands than the host allows. Instead of
letting drivers either reject or ignore this case handle it in
common code. Note that various driver use internal constant or
variables that are assigned to both shost->can_queue and checked
in ->change_queue_depth - I did remove those checks as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
All drivers use the implementation for ramping the queue up and down, so
instead of overloading the change_queue_depth method call the
implementation diretly if the driver opts into it by setting the
track_queue_depth flag in the host template.
Note that a few drivers validated the new queue depth in their
change_queue_depth method, but as we never go over the queue depth
set during slave_configure or the sysfs file this isn't nessecary
and can safely be removed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
This patch cleanups all PCIE, RSS & FW related macros/register defines that are
defined in t4fw_api.h and the affected files.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleanups PF/VF and LDST related macros/register defines that are
defined in t4fw_api.h and the affected files.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleanups all filter related macros/register defines that are defined
in t4fw_api.h and the affected files.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ieee802154/fakehard.c
A bug fix went into 'net' for ieee802154/fakehard.c, which is removed
in 'net-next'.
Add build fix into the merge from Stephen Rothwell in openvswitch, the
logging macros take a new initial 'log' argument, a new call was added
in 'net' so when we merge that in here we have to explicitly add the
new 'log' arg to it else the build fails.
Signed-off-by: David S. Miller <davem@davemloft.net>
