Assigning a socket in timewait state to skb->sk can trigger
kernel oops, e.g. in nfnetlink_log, which does:
if (skb->sk) {
read_lock_bh(&skb->sk->sk_callback_lock);
if (skb->sk->sk_socket && skb->sk->sk_socket->file) ...
in the timewait case, accessing sk->sk_callback_lock and sk->sk_socket
is invalid.
Either all of these spots will need to add a test for sk->sk_state != TCP_TIME_WAIT,
or xt_TPROXY must not assign a timewait socket to skb->sk.
This does the latter.
If a TW socket is found, assign the tproxy nfmark, but skip the skb->sk assignment,
thus mimicking behaviour of a '-m socket .. -j MARK/ACCEPT' re-routing rule.
The 'SYN to TW socket' case is left unchanged -- we try to redirect to the
listener socket.
Cc: Balazs Scheidler <bazsi@balabit.hu>
Cc: KOVACS Krisztian <hidden@balabit.hu>
Signed-off-by: Florian Westphal <fwestphal@astaro.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
If the new connection update parameter are accepted, the LE master
host sends the LE Connection Update Command to its controller informing
the new requested parameters.
Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Use proper timer instead of hci command flow control to timeout
failed hci commands. Otherwise stack ends up sending commands
when flow control is used to block new commands.
2010-09-01 18:29:41.592132 < HCI Command: Remote Name Request (0x01|0x0019) plen 10
bdaddr 00:16:CF:E1:C7:D7 mode 2 clkoffset 0x0000
2010-09-01 18:29:41.592681 > HCI Event: Command Status (0x0f) plen 4
Remote Name Request (0x01|0x0019) status 0x00 ncmd 0
2010-09-01 18:29:51.022033 < HCI Command: Remote Name Request Cancel (0x01|0x001a) plen 6
bdaddr 00:16:CF:E1:C7:D7
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
If the fail happens the HCI del_timer may timeout after the the hci dev
unregister. This lead to a kernel crash.
Reported-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Implements L2CAP Connection Parameter Update Response defined in
the Bluetooth Core Specification, Volume 3, Part A, section 4.21.
Address the LE Connection Parameter Procedure initiated by the slave.
Connection Interval Minimum and Maximum have the same range: 6 to
3200. Time = N * 1.25ms. Minimum shall be less or equal to Maximum.
The Slave Latency field shall have a value in the range of 0 to
((connSupervisionTimeout / connIntervalMax) - 1). Latency field shall
be less than 500. connSupervisionTimeout = Timeout Multiplier * 10 ms.
Multiplier field shall have a value in the range of 10 to 3200.
Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch splits the L2CAP command handling function in order to
have a clear separation between the commands related to BR/EDR and
LE. Commands and responses in the LE signaling channel are not being
handled yet, command reject is sent to all received requests. Bluetooth
Core Specification, Volume 3, Part A, section 4 defines the signaling
packets formats and allowed commands/responses over the LE signaling
channel.
Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Separate LE and ACL timeouts. Othervise ACL connections
on non LE hw will time out after 45 secs.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Fix LE connections not being marked as master.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
l2cap over LE links can be disconnected without sending
disconnect command first.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add support for LE server sockets.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add basic LE connection support to L2CAP. LE
connection can be created by specifying cid
in struct sockaddr_l2
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth chips may have separate buffers for LE traffic.
This patch add support to use LE buffers provided by the chip.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth V4.0 adds support for Low Energy (LE) connections.
Specification introduces new set of hci commands to control LE
connection. This patch adds logic to create, cancel and disconnect
LE connections.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
When IP_VS schedulers do not find a destination, they output a terse
"WLC: no destination available" message through kernel syslog, which I
can not only make sense of because syslog puts them in a logfile
together with keepalived checker results.
This patch makes the output a bit more informative, by telling you which
virtual service failed to find a destination.
Example output:
kernel: [1539214.552233] IPVS: wlc: TCP 192.168.8.30:22 - no destination available
kernel: [1539299.674418] IPVS: wlc: FWM 22 0x00000016 - no destination available
I have tested the code for IPv4 and FWM services, as you can see from
the example; I do not have an IPv6 setup to test the third code path
with.
To avoid code duplication, I put a new function ip_vs_scheduler_err()
into ip_vs_sched.c, and use that from the schedulers instead of calling
IP_VS_ERR_RL directly.
Signed-off-by: Patrick Schaaf <netdev@bof.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
Remove code that should not be called anymore.
Now when ip_vs_out handles replies for local clients at
LOCAL_IN hook we do not need to call conn_out_get and
handle_response_icmp from ip_vs_in_icmp* because such
lookups were already performed for the ICMP packet and no
connection was found.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Fix get_curr_sync_buff to keep buffer for 2 seconds
as intended, not just for the current jiffie. By this way
we will sync more connection structures with single packet.
Signed-off-by: Tinggong Wang <wangtinggong@gmail.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
For testing and debugging purposes it is useful to be able to disable
hardware acceleration of RFS without disabling RFS altogether. Since
this is a similar feature to 'n-tuple' flow steering through the
ethtool API, test the same feature flag that controls that.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
If the root qdisc for a net device is mqprio, and the driver's
ndo_setup_tc() operation dynamically adds and remvoes TX queues,
netif_set_real_num_tx_queues() will be called during device
unregistration to remove the extra TX queues when the qdisc is
destroyed. Currently this causes the corresponding kobjects
to be leaked, and the device's reference count never drops to 0.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
l2cap_load() was added to trigger l2cap.ko module loading from the RFCOMM
and BNEP modules. Now that L2CAP module is gone, we don't need it anymore.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Note that we do not generate the redirect netevent any longer,
because we don't create a new cached route.
Instead, once the new neighbour is bound to the cached route,
we emit a neigh update event instead.
Signed-off-by: David S. Miller <davem@davemloft.net>
The general idea is that if we learn new PMTU information, we
bump the peer genid.
This triggers the dst_ops->check() code to validate and if
necessary propagate the new PMTU value into the metrics.
Learned PMTU information self-expires.
This means that it is not necessary to kill a cached route
entry just because the PMTU information is too old.
As a consequence:
1) When the path appears unreachable (dst_ops->link_failure
or dst_ops->negative_advice) we unwind the PMTU state if
it is out of date, instead of killing the cached route.
A redirected route will still be invalidated in these
situations.
2) rt_check_expire(), rt_worker_func(), et al. are no longer
necessary at all.
Signed-off-by: David S. Miller <davem@davemloft.net>
NETDEV_NOTIFY_PEER is an explicit request by the driver to send a link
notification while NETDEV_UP/NETDEV_CHANGEADDR generate link
notifications as a sort of side effect.
In the later cases the sysctl option is present because link
notification events can have undesired effects e.g. if the link is
flapping. I don't think this applies in the case of an explicit
request from a driver.
This patch makes NETDEV_NOTIFY_PEER unconditional, if preferred we
could add a new sysctl for this case which defaults to on.
This change causes Xen post-migration ARP notifications (which cause
switches to relearn their MAC tables etc) to be sent by default.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicate inclusion of "send.h" and "routing.h" from
net/batman-adv/soft-interface.c
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
With previous patch, rose_get_neigh() routine
investigates the full list of neighbor nodes
until it finds or not an already connected node whether
it is called locally or through a level 3 transit frame.
If no routes are opened through an adjacent connected node
then a classical connect request is attempted.
Then there is no more reason for an extra loop such
as the one removed by this patch.
Signed-off-by: Bernard Pidoux <f6bvp@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
FPAC AX25 packet application is using Linux kernel ROSE
routing skills in order to connect or send packets to remote stations
knowing their ROSE address via a network of interconnected nodes.
Each FPAC node has a ROSE routing table that Linux ROSE module is
looking at each time a ROSE frame is relayed by the node or when
a connect request to a neighbor node is received.
A previous patch improved the system time response by looking at
already established routes each time the system was looking for a
route to relay a frame. If a neighbor node routing the destination
address was already connected, then the frame would be sent
through him. If not, a connection request would be issued.
The present patch extends the same routing capability to a connect
request asked by a user locally connected into an FPAC node.
Without this patch, a connect request was not well handled unless it
was directed to an immediate connected neighbor of the local node.
Implemented at a number of ROSE FPAC node stations, the present patch
improved dramatically FPAC ROSE routing time response and efficiency.
Signed-off-by: Bernard Pidoux <f6bvp@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
WFA certification and the WMM spec require that we
always reply to unicast probe requests, so do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_rx_h_check returned RX_DROP_MONITOR in case the if statement
in question was true but the same return value is also used directly
after the if clause. Hence, we can just drop the whole if clause and as
such simplify the code.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Actually doesn't make sense have these modules built separately.
The L2CAP layer is needed by almost all Bluetooth protocols and profiles.
There isn't any real use case without having L2CAP loaded.
SCO is only essential for Audio transfers, but it is so small that we can
have it loaded always in bluetooth.ko without problems.
If you really doesn't want it you can disable SCO in the kernel config.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Commit 0c838ff1ad (ipv4: Consolidate all default route selection
implementations.) forgot to remove one rcu_read_unlock() from
fib_select_default().
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the cleanup code in mqprio_destroy() is currently conditional on
priv->qdiscs being non-null, but that condition should only apply to
the per-queue qdisc cleanup. We should always set the number of
traffic classes back to 0 here.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
As noticed by Eric, nf_iterate doesn't use RCU correctly by
accessing the prev pointer of a RCU protected list element when
a verdict of NF_REPEAT is issued.
Fix by jumping backwards to the hook invocation directly instead
of loading the previous list element before continuing the list
iteration.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This reverts commit 44bd4de9c2.
I have to revert the early loop termination in connlimit since it generates
problems when an iptables statement does not use -m state --state NEW before
the connlimit match extension.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Struct tmp is copied from userspace. It is not checked whether the "name"
field is NULL terminated. This may lead to buffer overflow and passing
contents of kernel stack as a module name to try_then_request_module() and,
consequently, to modprobe commandline. It would be seen by all userspace
processes.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
struct sco_conninfo has one padding byte in the end. Local variable
cinfo of type sco_conninfo is copied to userspace with this uninizialized
one byte, leading to old stack contents leak.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Struct ca is copied from userspace. It is not checked whether the "device"
field is NULL terminated. This potentially leads to BUG() inside of
alloc_netdev_mqs() and/or information leak by creating a device with a name
made of contents of kernel stack.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch allows userspace to enslave/release slave devices via netlink
interface using IFLA_MASTER. This introduces generic way to add/remove
underling devices.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
nla_nest_start() may return NULL. If it does then we'll blow up in
nla_nest_end() when we dereference the pointer.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The app_data priority may not be the same for all net devices.
In order for stacks with application notifiers to identify the
specific net device dcb_app_type should be passed in the ptr.
This allows handlers to use dev_get_by_name() to pin priority
to net devices.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev->master is now tightly connected to bonding driver. This patch makes
this pointer more general and ready to be used by others.
- netdev_set_master() - bond specifics moved to new function
netdev_set_bond_master()
- introduced netif_is_bond_slave() to check if device is a bonding slave
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to check (master) twice and to drive in and out the header file.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it turns out we never need to walk through the list of multicast
groups subscribed by the bridge interface itself (the only time we'd
want to do that is when we shut down the bridge, in which case we
simply walk through all multicast groups), we don't really need to
keep an hlist for mp->mglist.
This means that we can replace it with just a single bit to indicate
whether the bridge interface is subscribed to a group.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
