I found a problem using an IPv6 over IPv4 tunnel. When CONFIG_IPV6_SIT
was enabled, the packets would be rejected as net/ipv6/sit.c was catching
all IPPROTO_IPV6 packets and returning an ICMP port unreachable error.
I think this patch fixes the problem cleanly. I believe the code in
net/ipv4/tunnel4.c:tunnel4_rcv takes care of it properly if none of the
handlers claim the skb.
Signed-off-by: David McCullough <david_mccullough@mcafee.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use strncpy instead of memcpy when working on strings
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove printks for ring blocks, fifo blocks, and rx doorbell mode as
they clutter the dmesg output during modprobe and provide no useful
information.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ipip is built as a module the 'ip tunnel add' command would fail because
the ipip module was not being autoloaded. Adding an alias for
the tunl0 device name cause dev_load() to autoload it when needed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If gre is built as a module the 'ip tunnel add' command would fail because
the ip_gre module was not being autoloaded. Adding an alias for
the gre0 device name cause dev_load() to autoload it when needed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use strcpy() rather the sprintf() for the case where name is getting
generated. Fix indentation.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate qdisc memory according to NUMA properties of cpus included in
xps map.
To be effective, qdisc should be (re)setup after changes
of /sys/class/net/eth<n>/queues/tx-<n>/xps_cpus
I added a numa_node field in struct netdev_queue, containing NUMA node
if all cpus included in xps_cpus share same node, else -1.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIC partitioning is another flavor of multi function - having few
PCI functions share the same physical port. Unlike the currently
supported mode of multi-function which depends on the switch
configuration and uses outer-VLAN, the NPAR mode is switch independent
and uses the MAC addresses to distribute incoming packets to the different
functions. This patch adds the specific HW setting of the NPAR mode
and some distinctions between switch dependent (SD) and
switch independent (SI) multi-function (MF) modes where the configuration
is not the same.
Advance driver version to 1.60.00-6
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restore the check for an unassigned mac address before adopting the
first slaves as it's own. The change in behavior was introduced by:
commit c20811a79e
Author: Jiri Pirko <jpirko@redhat.com>
bonding: move dev_addr cpy to bond_enslave
Signed-off-by: David Strand <dpstrand@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code for the b44_wap54g10_workaround was never included, because
the config option was wrong. The nvram_get function was never in
mainline kernel, only in external OpenWrt patches.
The code should be compiled in when CONFIG_BCM47XX is selected and not
when CONFIG_SSB_DRIVER_MIPS is selected, because nvram_getenv is only
available on bcm47xx platforms and now in the mainline kernel code.
Using an include is better than a second function declaration, to fix
this when the function signature changes.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip6_tunnel always assumes it consumes 40 bytes (ip6 hdr) of the mtu of the
underlaying device. So for a normal ethernet bearer, the mtu of the ip6_tunnel is
1460.
However, when creating a tunnel the encap limit option is enabled by default, and it
consumes 8 bytes more, so the true mtu shall be 1452.
I dont really know if this breaks some statement in some RFC, so this is a request for
comments.
Signed-off-by: Anders Franzen <anders.franzen@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Atheros 3011 has small sflash firmware and needs to be
blacklisted in transport driver to load actual firmware
in DFU driver.
Signed-off-by: Bala Shanmugam <sbalashanmugam@atheros.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
If a device is autosuspended an inability to resubmit URBs is
to be expected. Check the error code and only log real errors.
(Now that autosuspend is default enabled for btusb, those log
messages were happening all the time e.g. with a BT mouse)
Signed-off-by: Stefan Seyfried <seife+kernel@b1-systems.com>
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Then we can make a completely generic tcp_remember_stamp()
that uses ->get_peer() as a helper, minimizing the AF specific
code and minimizing the eventual code duplication when we implement
the ipv6 side of TW recycling.
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of directly accessing "peer", change to code to
operate using a "struct inet_peer_base *" pointer.
This will facilitate the addition of a seperate tree for
ipv6 peer entries.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dbbf1755b0 "iwlwifi: use
antenna information in EEPROM" caused 4965 device breakage with
"Microcode SW error detected. Restarting 0x82000000." message.
This patch reverts 4965 part of that commit.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove a superfluous ieee80211_is_data check as that was checked a few
lines before already and we wont't get here for non-data frames at all.
Second, the frame was already converted to 802.3 header format and
reading the fc and addr1 fields was only possible because the 802.3
header is short enough and didn't overwrite the relevant parts of the
802.11 header. Make the code more obvious by checking the ethernet
header's h_dest field.
Furthermore reorder the conditions to reduce the number of checks
when dynamic powersave is not needed (AP mode for example).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All rt2x00 drivers except rt2800pci call ieee80211_tx_status() from
a workqueue, which causes "NOHZ: local_softirq_pending 08" messages.
To fix it, add ieee80211_tx_status_ni() similar to ieee80211_rx_ni()
which can be called from process context, and call it from
rt2x00lib_txdone(). For the rt2800pci special case a driver
flag is introduced.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* A diff between rfbuffer settings of turbo and non-turbo
modes indicates there is a bit on bank 2 related to turbo operation
(it's set on turbo modes). This bit is present on all radios except
RF5413 that seems to have a completely different bank 2. Also
since 2317 has the same rf-registers locations with 2425 and
since the bit exists on 2317 I assume it also exists on 2425/2417).
So in case we use turbo mode (40MHz) enable it on bank modification.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Clean up what's left of turbo mode, since we handle all
register modifications (rfbuffer comes next) on code there
is no need to have duplicated arrays.
* Rename change_channel to skip_pcu on initvals.c as we did
on reset.c
Signed-off-by: Nick Kossifidis <micklfemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Clean up CHANNEL_T(URBO), use AR5K_BWMODE_40MHZ instead
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Use correct clock value when setting OFDM timings on
non-default bwmodes.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Don't return -EINVAL when trying to set tx power
on RF5110 because AR5210 reset will fail. We need to
add support for RF5110 and AR5210 eeprom in the future
but for now just skip it.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Tweak phy activation -> rx delay for different bwmodes
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Since we set antenna flags on phy init and ack bitrate
mode on pcu init, there is no need to save/restore sta_id
flags on ath5k_hw_reset. Also we don't need to re-set our
mac address because it's not affected by resets.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add synth-only channel change for AR2413/5413. When we call
ath5k_reset with a channel ath5k_hw_reset will first try to
set channel on PHY while PHY is running instead of doing a normal
full reset. To do this phy_init has to change to implement this
functionality.
* Clean up change_channel flag, what it really did was skip PCU
registers when setting initvals. This is done because on reset
PCU registers are not affected (except the registers we set
in pcu init and -due to hw problems- TSF). Use a new skip_pcu
flag that's not misleading instead. In the future we might use
that to also skip PCU reset and save us the TSF etc problems
(needs testing because standard practice is to reset everything).
* Use fast channel change only when setting channel, and set skip_pcu
to false only on init. When we reset the card due to DMA or PHY
problems skip pcu but never do a fast channel change.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Only set power table if we are changing channel/mode
there is no need to recalculate and reset the power table
all the time.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Set correct PLL settings for each bwmode
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add spur mitigation filter support for half/quarter and turbo.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Tweak power detector delays on AR5111/AR5112 when
using half/quarter modes.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Make sure we always set IFS timings even if no
coverage class is set. If we don't we'll miss the
needed changes for different bwmodes.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Set AR5K_DCU_GBL_IFS_MISC_TURBO_MODE flag on DCU when operating
on 40MHz
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Replace set_slot_time with set_ifs_intervals that also sets
the various inter-frame space intervals based on current bwmode.
* Clean up AR5210 mess from reset_tx_queue, AR5210 only has one
data queue and we set IFS intervals for that queue on set_ifs_intervals
so there is nothing left to do for 5210 on reset_tx_queue.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Extend ieee80211_generic_frame_duration to support the various
bwmodes.
* Better document what's going on with ack bitrates and update
write_rate_duration to support the standard ack bitrates (when
we don't set the high bit).
* Get rid of set_ack_bitrate_high and introduce a flag on ath5k_hw
for this (we only called the function on init anyway so there is no
difference).
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Extend get_default_sifs/slot_time to include timings for turbo
half and quarter rate modes.
* AR5210 code for now uses timings already on core clock units
instead of usecs so rename them (we 'll clean it up later).
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Move setting of tx retry limits on a separate function
(we 'll clean up this AR5210 mess later)
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* On turbo mode increase PHY settling times, note that
we only increase switch settling time on AR5212 as indicated
by initvals.
* A few cleanups: Move frame control settings for AR5210 from
reset_tx_queue to tweak_initvals and remove phy_scal settings
from tweak_initvals (we tweak them alread on set_sleep_clock).
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Now that we properly set rx/tx latencies for AR5311 remove
that old buggy part of code left inside ath5k_hw_tweak_initval_settings
that was never executed (you can't have an RF5112 radio on a mac older
than AR5212). Also use a magic value for 5311 PHY_SCAL value.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Handle all usec parameters in one function. It's much cleaner
this way.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Prepare for half/quarter/turbo support, introduce a new
ah_bwmode parameter and get rid of ah_turbo. Bwmode stands
for "bandwidth mode" and can have 4 values, default (20MHz),
turbo (40MHz), half rate (10MHz), and quarter rate (5MHz).
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Since we only use ath5k_hw_stop_tx_dma to stop the beacon
queue, introduce a new function ath5k_hw_stop_beacon_queue so
that we can use that instead and have better control. In the future
we can add more beacon queue specific stuff there (maybe tweak
beacon timers or something), for now just call ath5k_hw_stop_tx_dma.
* Also since we don't call ath5k_hw_stop_rx/tx_dma from outside
dma.c, make them static.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Make sure we are not trying to set RXDP while RX is active,
for now ignore the return value.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
