Since this is a SOM (System on Module) that will be part
of another embedded board (and can't really exist on its own)
define it as a "dtsi" that will be included in the Device tree
describing the whole system later on.
Hardware specification:
* AM335x SoC
* up to 512 MB RAM
* NAND Flash (8x interface, cs0)
* UART0
* PMIC
* I2C0 (for PMIC)
* 1x Ethernet MAC
Signed-off-by: Rostislav Lisovy <lisovy@jablotron.cz>
[tony@atomide.com: updated nand io size to be just 4]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull "This pull request contains the following changes from Ray for Cygnus SoCs: from Florian Fainelli:
- enable IOMUX, required for pinmux/pinctrl
- enable GPIO, required for the GPIO driver
- enable GPIO hook detection for BCM911360-based phone designs
- enable PCIe controller for the bcm958300k designs
* tag 'arm-soc/for-4.1/devicetree-part-2' of http://github.com/broadcom/stblinux:
ARM: dts: enable PCIe support for Cygnus
ARM: dts: cygnus: enable GPIO based hook detection
ARM: dts: enable GPIO for Broadcom Cygnus
ARM: dts: enable IOMUX for Broadcom Cygnus
This patch introduces devicetree for the Alpine platform, and
for a development board based on the same platform.
Signed-off-by: Barak Wasserstrom <barak@annapurnalabs.com>
Signed-off-by: Tsahee Zidenberg <tsahee@annapurnalabs.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add PCIe device nodes in bcm-cygnus.dtsi but keep them disabled there.
Only enable them for bcm958300k where PCIe interfaces are populated
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This adds the static vcc_sys regulator to the rk3288-evb, the missing
rk808 supplies from it and all the supplies of the act8846 evb-variant.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
- fix SDHCI nodes on Armada 38x
- add Linksys WRT1900AC (Mamba) support (including the Ethernet switch)
- add several fixes and improvement for dove
- enable GPIO fan alarm support for 2Big Network v2
- add several fixes about unit address
- add support for Armada 39x SoC and board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlT9S+0ACgkQCwYYjhRyO9XSkQCfcrsiF6bS+B1B9Gdu+nBwyXdC
BHYAmwUm92D7yH8ePjbKldM4ONM1315b
=yn/6
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.1' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt changes for v4.1 (part #1)" from Gregory CLEMENT:
- fix SDHCI nodes on Armada 38x
- add Linksys WRT1900AC (Mamba) support (including the Ethernet switch)
- add several fixes and improvement for dove
- enable GPIO fan alarm support for 2Big Network v2
- add several fixes about unit address
- add support for Armada 39x SoC and board
* tag 'mvebu-dt-4.1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: add Device Tree files for Armada 39x SoC and board
ARM: mvebu: fix unit address of MPIC nodes
ARM: mvebu: use stdout-path in all armada-*.dts
ARM: mvebu: add serial port aliases on Armada 370/375/38x/XP
ARM: mvebu: remove aliases for Ethernet devices on Armada 370/375/38x/XP
ARM: mvebu: add UART labels to Armada 375
ARM: mvebu: add missing UART labels on Armada 38x
ARM: mvebu: fix usb@ unit address on Armada 38x to match register address
ARM: mvebu: a385-db-ap: Enable the NAND
ARM: ARMADA XP: WRT1900AC: Add support for the Ethernet switch
ARM: Kirkwood: enable GPIO fan alarm support for 2Big Network v2
ARM: mvebu: Fix MPIC unit address
ARM: dts: dove: Add some more common pinctrl settings
ARM: dts: dove: Add node labels for PCIe ports 0 and 1
ARM: dts: dove: Always include gpio and interrupt-controller headers
ARM: dts: dove: Fix uart[23] reg property
ARM: mvebu: add Linksys WRT1900AC (Mamba) support
ARM: mvebu: Add Device Tree description of SDHCI for Armada 388 RD
ARM: mvebu: Update the SDHCI node on Armada 38x
ARM: mvebu: Use macros for interrupt flags on Armada 38x sdhci node
Pull "Broadcom Device Tree changes for 4.1 #1" from Florian Fainelli:
This pull request contains the following Broadcom SoCs Device Tree changes:
- Jonathan adds support for the Broadcom Cygnus BCM958305K board
- Rafal adds support for Netgear R8000 and fixes the default for power LEDs
on Netgear R6250
* tag 'arm-soc/for-4.1/devicetree' of http://github.com/broadcom/stblinux:
ARM: BCM5301X: Fix default state of power LEDs on Netgear R6250
ARM: BCM5301X: Add DT for Netgear R8000
ARM: dts: Enable Broadcom Cygnus BCM958305K
- clock fixes for USB
- compatible string changes for handling USB IP differences
(+ needed AHB matrix syscon)
- fix of a compilation error in PM code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVAFaGAAoJEAf03oE53VmQilsH/Aie6f2WmzqtBACUTJKae3Kj
BLXyewX89rSEDuUEjImJhYdafYDEq/5IeoeRMY/qPdXKrY0KCEhwnVUT5LEH3qy3
P8yl0UAtZycMnKtP2YhFRAFUY/DozxprcOqTw4IfZ7PHHsQKcn4+qrgG8LcHpvfZ
d5wv6C+6gi9UBh3B7omOx98ULFDOnST56UhOml9HGsdOgCc7AbsusEG4FzRON7Bc
4QEJuYxxZPONoeuczpn9qF8SFk9ShO5dHQsjzWkSZjgneBPJK7vujcItR9KWWqw5
gtjQ19BPNuAYY4MY6/2mc/qOGsA3o17Cn9CvNwaAnlvMLebk4tMAWL8Y9Dmjouc=
=l68g
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes3' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
Pull "Third fixes batch for AT91 on 4.0" from Nicolas Ferre:
- clock fixes for USB
- compatible string changes for handling USB IP differences
(+ needed AHB matrix syscon)
- fix of a compilation error in PM code
* tag 'at91-fixes3' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91: pm_slowclock: fix the compilation error
ARM: at91/dt: fix USB high-speed clock to select UTMI
ARM: at91/dt: fix at91 udc compatible strings
ARM: at91/dt: declare matrix node as a syscon device
ARM: at91/dt: at91sam9261: fix clocks and clock-names in udc definition
This patch adds the DT description for the LaCie "2Big NAS" (nas2big).
This NAS is an hardware upgrade of the 2Big Network v2.
Chipset and device list:
- CPU Marvell 88F6282 1600Mhz
- SDRAM memory, 256MB DDR3 (2x128MB x8) 533Mhz
- 1 Ethernet Gigabit port (PHY Marvell 88E1518)
- Flash memory, NAND 256MB TSOP48
- I2C EEPROM, 512 bytes (AT24 type)
- PCIe SATA controller JMicron JMB360 (eSATA)
- I2C fan controller GMT G762 (with a separate alarm GPIO)
- 1 USB2 host port
- 1 push button
- 1 power switch
- 2 SATA LEDs (bi-color, blue and red)
- 1 power LED (bi-color, blue and red)
- CPLD for LEDs and start-up management (Altera Max EMP3064)
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The UTMI clock must be selected by any high-speed USB IP. The logic behind it
needs this particular clock.
So, correct the clock in the device tree files affected.
Reported-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org> #3.18
The at91rm9200, at91sam9260, at91sam9261 and at91sam9263 SoCs have slightly
different UDC IPs.
Those differences were previously handled with cpu_is_at91xx macro which
are about to be dropped for multi-platform support, thus we need to
change compatible strings.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
There is no specific driver handling the AHB matrix, this is a simple syscon
device. the matrix is needed by several other drivers including the USB on some
SoCs (at91sam9261 for instance).
Without this definition, the USB will not work on these SoCs.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
It includes a couple of i.MX6 dts fixes, which set an input supply to
vbus regulator. Without the fixes, the voltage of vbus is incorrect
after system boots up.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU/8l7AAoJEFBXWFqHsHzOb3sH/1fFkQXzUcAon971XnD3sP55
zAbUvcowEQ/04xpb3Q5r5KCfeN4UvOCSY6Zed4sevq/TJZidYl8DKu9q4s0rSnfX
m1GghT3pAixMlyEWdJldmIwTYBXEkaJVrqeNuTB6BqBIsInWW/R+WkuByrPGkaxS
P5ENbyMVz68S0Cq88lmYzFjRXCCc2vWPZiVKj0DEOnqld1TIpY9hQyZwHmepCydZ
GKHLApyWP9qyUs/N6Bxwt/2vPoauit2xfDTvCbBk75jO34uSYEo9L9YpwDQorXPW
f6vj1EkVqW3TljghEm/kSoi1nhU2fNnfUAWClfKQ1UO2yzNLQAWtY+23upR5Qkw=
=kuEJ
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Pull "The i.MX fixes for 4.0" from Shawn Guo:
It includes a couple of i.MX6 dts fixes, which set an input supply to
vbus regulator. Without the fixes, the voltage of vbus is incorrect
after system boots up.
* tag 'imx-fixes-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx6sl-evk: set swbst_reg as vbus's parent reg
ARM: imx6qdl-sabresd: set swbst_reg as vbus's parent reg
with the bigger changes being for the dra7 clocks and hwmod data:
- Fix wl12xx for dm3730-evm
- Fix omap4 prm save and clea
- Fix hwmod clkdm use count
- Fix hwmod data for pcie on dra7
- Fix lockdep for hwmod
- Fix USB on most omap3 boars by enabling it in the defconfig
- Fix the bypass clock source for omap5 and dra7
- Fix the ehrpwm clock for am33xx and am43xx
- Enable AES and SHAM for BeagleBone white
- Use rmii clock for am335x-lxm
- Fix polling intervals for omap5 thermal zones
- Fix slewctrl for am33xx and am43xx
- Fix dra7-evm dcan pinctrl
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C0ct
-----END PGP SIGNATURE-----
Merge tag 'fixes-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Pull "omap fixes against v4.0-rc2" from Tony Lindgren:
Fixes for various omap variants, mostly minor fixes for various SoCs
with the bigger changes being for the dra7 clocks and hwmod data:
- Fix wl12xx for dm3730-evm
- Fix omap4 prm save and clea
- Fix hwmod clkdm use count
- Fix hwmod data for pcie on dra7
- Fix lockdep for hwmod
- Fix USB on most omap3 boars by enabling it in the defconfig
- Fix the bypass clock source for omap5 and dra7
- Fix the ehrpwm clock for am33xx and am43xx
- Enable AES and SHAM for BeagleBone white
- Use rmii clock for am335x-lxm
- Fix polling intervals for omap5 thermal zones
- Fix slewctrl for am33xx and am43xx
- Fix dra7-evm dcan pinctrl
* tag 'fixes-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix wl12xx on dm3730-evm with mainline u-boot
ARM: OMAP: enable TWL4030_USB in omap2plus_defconfig
ARM: dts: dra7x-evm: avoid possible contention while muxing on CAN lines
ARM: dts: dra7x-evm: Don't use dcan1_rx.gpio1_15 in DCAN pinctrl
ARM: dts: am43xx: fix SLEWCTRL_FAST pinctrl binding
ARM: dts: am33xx: fix SLEWCTRL_FAST pinctrl binding
ARM: dts: OMAP5: fix polling intervals for thermal zones
ARM: dts: am335x-lxm: Use rmii-clock-ext
ARM: dts: am335x-bone-common: enable aes and sham
ARM: dts: am43xx-clocks: Fix ehrpwm tbclk data on am43xx
ARM: dts: am33xx-clocks: Fix ehrpwm tbclk data on am33xx
ARM: dts: OMAP5: Fix the bypass clock source for dpll_iva and others
ARM: dts: DRA7x: Fix the bypass clock source for dpll_iva and others
ARM: OMAP4+: PRM: fix omap4 version of prm_save_and_clear_irqen
ARM: OMAP2+: hwmod: fix deassert hardreset clkdm usecounting
ARM: DRA7: hwmod_data: Fix hwmod data for pcie
ARM: omap2+: omap_hwmod: Set unique lock_class_key per hwmod
- little fix for !MMU debug: may also help for randconfig
- fix of 2 errors in LCD clock definitions
- in PM code, not writing the key leads to not execute the action
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJU+DZAAAoJEAf03oE53VmQe34H/3cACqt00PvJiJ/DJNOLq8xM
1E93vZb/sQ5nD4JwF1DK1/VezT8QjOpIdb/Uo/XIKxqV0T7ZfFcLcAYHDCZup1HP
VbNtGRYPDGtQypBBVHDgCHwfgH6QVjTQJk67vjZkKmvWXFBnv6akY2XTrXLeMBKw
24nWEamrpR5tlEG5z9WIx6YFYBslDHq+R8j98AThJRo3NI+d00FPYwfDEwNf730e
T4xh/Rzz9eNbttBoTP5AeN75OXowsnpZwVicbQNtkX0E2jNdv1Ltbkpzc9zWdw8m
pL1kf+sV2MvD7KvcOrFGXMD2Ei3MCUNFdscaftQvfjutjEdmF2eIcK4qAzYRifw=
=UTAc
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
Pull "Second fixes batch for AT91 on 4.0" from Nicolas Ferre:
- little fix for !MMU debug: may also help for randconfig
- fix of 2 errors in LCD clock definitions
- in PM code, not writing the key leads to not execute the action
* tag 'at91-fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/pm: MOR register KEY was missing
ARM: at91/dt: sama5d4: fix lcdck clock definition
ARM: at91/dt: sama5d4: rename lcd_clk into lcdc_clk
ARM: at91: debug: fix non MMU debug
- Fix the SCU virtual mapping
- Add misssing DMA channels for UART nodes
- Fix a sporadic SMP error where CPU1 was not seeing its start address
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pm9Y
-----END PGP SIGNATURE-----
Merge tag 'socfpga_fixes_for_v4.0' of git://git.rocketboards.org/linux-socfpga-next into fixes
Pull "Fixes for v4.0 on the SoCFPGA platform" from Dinh Nguyen:
- Fix the SCU virtual mapping
- Add misssing DMA channels for UART nodes
- Fix a sporadic SMP error where CPU1 was not seeing its start address
* tag 'socfpga_fixes_for_v4.0' of git://git.rocketboards.org/linux-socfpga-next:
ARM: socfpga: make sure socfpga_cpu1start_addr is properly flushed
ARM: socfpga: fix uart DMA binding error
ARM: socfpga: Correct SCU virtual mapping in socfpga
USB vbus 5V is from PMIC SWBST, so set swbst_reg as vbus's
parent reg, it fixed a bug that the voltage of vbus is incorrect
due to swbst_reg is disabled after boots up.
Cc: stable@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
USB vbus 5V is from PMIC SWBST, so set swbst_reg as vbus's
parent reg, it fixed a bug that the voltage of vbus is incorrect
due to swbst_reg is disabled after boots up.
Cc: stable@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Audio DMAC peri peri is no longer DMAEngine. it is supported by
sound driver. this patch enable it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Audio DMAC peri peri is no longer DMAEngine. it is supported by
sound driver. this patch enable it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This enables all 3 GPIO controllers including the ASIU GPIO, the
chipcommonG GPIO, and the ALWAYS-ON GPIO, for Broadcom Cygnus SoC
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Tested-by: Dmitry Torokhov <dtor@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This enables the IOMUX support for Broadcom Cygnus SoC
Signed-off-by: Ray Jui <rjui@broadcom.com>
Tested-by: Dmitry Torokhov <dtor@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Peripheral clock is named pclk and system clock is named hclk (those are
the names expected by the at91_udc driver).
Drop the deprecated usb_clk (formerly used to configure the usb clock rate
which is now directly configurable through hclk).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
On the Radxa Rock board most supplies come from the static 5v vsys supply, but
the inl1-supply comes from the REG4 of the act8846 itself. Model this dependency
using the added supply-handling to make sure the supplying regulator gets handled
correctly and not accidentially turned off.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The switches on r8a73a4/ape6evm do not have pull-up registers. The
schematics say: "Need to use APE6 internal PullUp", hence enable pull-up
using pinctrl.
Without this, the switches don't really work, as the GPIO inputs are
more likely to pick up ghost signals through capacitive coupling than
actual keypresses.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
DCAN1 RX and TX lines are internally pulled high according to [1].
While muxing between DCAN mode and SAFE mode we make sure
that the same pull direction is set to minimize opposite
pull contention during the switching window.
[1] in DRA7 data manual, Ball characteristics table 4-2, DSIS colum shows
the state driven to the peripheral input while in the deselcted mode.
DSIS - De-Selected Input State.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rev.F onwards ball G19 (dcan1_rx) is used as a GPIO for some other
function so don't include it in DCAN pinctrl node.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 has a finer counter granularity, which allows for a delay of 1000ms
in the thermal zone polling intervals. OMAP5 has a different counter
mechanism, which allows at maximum a 500ms timer. Adjust the cpu thermal
zone polling interval accordingly.
Without this patch, the polling interval information is simply ignored,
and the following thermal warnings are printed during boot (assuming
thermal is enabled);
[ 1.545343] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[ 1.552691] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[ 1.560029] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use external clock for RMII since the internal clock doesn't meet the
jitter requirements.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Beaglebone Black doesn't have AES and SHAM enabled like the
original Beaglebone White dts. This breaks applications that
leverage the crypto blocks so fix this by enabling these nodes
in the am335x-bone-common.dtsi. With this change, enabling the
nodes in am335x-bone.dts is no longer required so remove them.
Signed-off-by: Matt Porter <mporter@konsulko.com>
Acked-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.
Fixes: 4da1c67719 ("add tbclk data for ehrpwm")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.
Fixes: 9e100ebafb: ("Fix ehrpwm tbclk data")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes 85dc74e9 (ARM: dts: omap5 clock data)
On OMAP54xx, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.
This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck
Fix this by adding another mux clock as parent in bypass mode.
This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:
DPLL_IVA,
DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes: ee6c750761 (ARM: dts: dra7 clock data)
On DRA7x, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.
This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck
Fix this by adding another mux clock as parent in bypass mode.
This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:
DPLL_IVA, DPLL_DDR,
DPLL_DSP, DPLL_EVE,
DPLL_GMAC, DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
lcdck takes mck (not smd) as its parent. It is also assigned id 3 and not 4.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: squashed 2 related patches]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Rename lcd_clk into lcdc_clk to be consistent with sama5d3 clock
definitions.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
