Some LCD controller cannot provide valid VESA style sync, i.e. coincident
HS/VS edges. First, this patch adds hskew passed from the adjusted_mode to
reference pixel calculation to allow those controllers to add an offset
relative to the expected reference pixel.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Russell King <rmk_kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes the wrong sync generation and sync calculation of TDA998x
for HS/VS-based sync detection.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Russell King <rmk_kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch adds tda998x specific parameters to allow it to be configured
for different boards using it. Also, this implements rudimentary audio
support for S/PDIF attached controllers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Russell King <rmk_kernel@arm.linux.org.uk>
Tested-by: Russell King <rmk_kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The video-input-port (VIP) is highly configurable. This prepares
current driver to allow to configure VIP configuration, as some
boards connect lcd controller and TDA998x "pin-swapped" and depend
on VIP to swap the pins by register configuration.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Russell King <rmk_kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The npix/nline registers are supposed to be programmed with the total
number of pixels/lines, not the displayed pixels/lines, and not minus
one either.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Russell King <rmk_kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When switching between various drivers for this device, it's possible
that some critical registers are left containing values which affect
the device operation. One such case encountered is the VIP output
mux register. This defaults to 0x24 on powerup, but other drivers may
set this to 0x12. This results in incorrect colours.
Fix this by ensuring that the register is always set to the power on
default setting.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Russell King <rmk_kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
TDA19988 devices need their RAM enabled in order to read EDID
information. Add support for this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Russell King <rmk_kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If NO_DMA=y:
drivers/built-in.o: In function `__drm_pci_free':
drivers/gpu/drm/drm_pci.c:112: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `drm_pci_alloc':
drivers/gpu/drm/drm_pci.c:72: undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `drm_gem_unmap_dma_buf':
drivers/gpu/drm/drm_prime.c:87: undefined reference to `dma_unmap_sg'
drivers/built-in.o: In function `drm_gem_map_dma_buf':
drivers/gpu/drm/drm_prime.c:78: undefined reference to `dma_map_sg'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
After any "soft gfx reset" we must manually invalidate the TLBs
associated with each ring. Empirically, it seems that a
suspend/resume or D3-D0 cycle count as a "soft reset". The symptom is
that the hardware would fail to note the new address for its status
page, and so it would continue to write the shadow registers and
breadcrumbs into the old physical address (now used by something
completely different, scary). Whereas the driver would read the new
status page and never see any progress, it would appear that the GPU
hung immediately upon resume.
Based on a patch by naresh kumar kachhi <naresh.kumar.kacchi@intel.com>
Reported-by: Thiago Macieira <thiago@kde.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64725
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Thiago Macieira <thiago@kde.org>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a callback hook to the chip ops struct to allow chips to have their
specific self-refresh function. Currently only used by cdv.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Add a callback hook to the chip ops struct to allow chips to have their
specific fifo watermark update function. Currently only cdv actually
tries to set wms based on crtc configuration but if/when the other chips
needs it we can attach a callback for them as well.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
If we get an error event really early in the driver setup sequence,
which gen3 is especially prone to with various display GTT faults we
Oops. So try to avoid this.
Additionally with Haswell the transcoders are a separate bank of
registers from the pipes (4 transcoders, 3 pipes). In event of an
error, we want to be sure we have a complete and accurate picture of
the machine state, so record all the transcoders in addition to all
the active pipes.
This regression has been introduced in
commit 702e7a56af
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Tue Oct 23 18:29:59 2012 -0200
drm/i915: convert PIPECONF to use transcoder instead of pipe
Based on the patch "drm/i915: Dump all transcoder registers on error"
from Chris Wilson:
v2: Rebase so that we don't try to be clever and try to figure out the
cpu transcoder from hw state. That exercise should be done when we
analyze the error state offline.
The actual bugfix is to not call intel_pipe_to_cpu_transcoder in the
error state capture code in case the pipes aren't fully set up yet.
v3: Simplifiy the err->num_transcoders computation a bit. While at it
make the error capture stuff save on systems without a display block.
v4: Fix fail, spotted by Jani.
v5: Completely new commit message, cc: stable.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60021
Cc: stable@vger.kernel.org
Tested-by: Dustin King <daking@rescomp.stanford.edu>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When the message buffer is currently moving block until it is idle again.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As a corollary to reviewing the interaction between LLC and our cache
domains, the GPU PTE bits are independent of the CPU PAT bits. As such
we can set the cache level on stolen memory based on how we wish the GPU
to cache accesses to it. So we are free to set the same default cache
levels as for normal bo, i.e. enable LLC cacheing by default where
appropriate.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As mentioned in the previous commit, reads and writes from both the CPU
and GPU go through the LLC. This gives us coherency between the CPU and
GPU irrespective of the attribute settings either device sets. We can
use to avoid having to clflush even uncached memory.
Except for the scanout.
The scanout resides within another functional block that does not use
the LLC but reads directly from main memory. So in order to maintain
coherency with the scanout, writes to uncached memory must be flushed.
In order to optimize writes elsewhere, we start tracking whether an
framebuffer is attached to an object.
v2: Use pin_display tracking rather than fb_count (to ensure we flush
cursors as well etc) and only force the clflush along explicit writes to
the scanout paths (i.e. pin_to_display_plane and pwrite into scanout).
v3: Force the flush after hitting the slowpath in pwrite, as after
dropping the lock the object's cache domain may be invalidated. (Ville)
Based on a patch by Ville Syrjälä.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The display engine has unique coherency rules such that it requires
special handling to ensure that all writes to cursors, scanouts and
sprites are clflushed. This patch introduces the infrastructure to
simply track when an object is being accessed by the display engine.
v2: Explain the is_pin_display() magic as the sources for obj->pin_count
and their individual rules is not obvious. (Ville)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The LLC is a fun device. The cache is a distinct functional block within
the SA that arbitrates access from both the CPU and GPU cores. As such
all writes to memory land first in the LLC before further action is
taken. For example, an uncached write from either the CPU or GPU will
then proceed to memory and evict the cacheline from the LLC. This means that
a read from the LLC always returns the correct information even if the PTE
bit in the GPU differs from the PAT bit in the CPU. For the older
snooping architecture on non-LLC, the fundamental principle still holds
except that some coordination is required between the CPU and GPU to
explicitly perform the snooping (which is handled by our request
tracking).
The upshot of this is that we know that we can issue a read from either
LLC devices or snoopable memory and trust the contents of the cache -
i.e. we can forgo a clflush before a read in these circumstances.
Writing to memory from the CPU is a little more tricky as we have to
consider that the scanout does not read from the CPU cache at all, but
from main memory. So we have to currently treat all requests to write to
uncached memory as having to be flushed to main memory for coherency
with all consumers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the FB CMA helpers to implement FBDEV emulation support. The VGA
connector status must be reported as connector_status_connected instead
of connector_status_unknown to be usable by the emulation layer.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The R8A7790 includes two internal LVDS encoders. Support them in the DU
driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The R8A7790 DU variant has a single RGB output called DPAD0 that can be
fed with the output of DU0, DU1 or DU2. Making the routing configurable.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Split the output routing specification between SoC-internal data,
specified in the rcar_du_device_info structure, and board data, passed
through platform data.
The DU has 5 possible outputs (DPAD0/1, LVDS0/1, TCON). SoC-internal
output routing data specify which output are valid, which CRTCs can be
connected to the valid outputs, and the type of in-SoC encoder for the
output.
Platform data then specifies external encoders and the output they are
connected to.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The R8A7790 DU seems to require a 128 bytes pitch alignment, even though
the documentation only mentions a 16 pixels alignement as for the
R8A7779 DU. Make this configurable through a device flag.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The DU revision in the R8A7790 SoC uses one IRQ and clock per CRTC. Add
a corresponding entry in the module platform ID table.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Output routing is configured in group registers, move the corresponding
code from rcar_du_crtc.c to rcar_du_group.c.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Channels are accessed through a global channel memory offset, there's no
need to define register addresses for the second channel.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The rcar_du_device structure contains a field that stores the number of
CRTCs, use it instead of the CRTCs array size. This prepares the driver
to support a variable number of CRTCs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The R8A7779 DU is split in per-CRTC resources (scan-out engine, blending
unit, timings generator, ...) and device-global resources (start/stop
control, planes, ...) shared between the two CRTCs.
The R8A7790 introduced a third CRTC with its own set of global resources
This would be modeled as two separate DU device instances if it wasn't
for a handful or resources that are shared between the three CRTCs
(mostly related to input and output routing). For this reason the
R8A7790 DU must be modeled as a single device with three CRTCs, two sets
of "semi-global" resources, and a few device-global resources.
Introduce a new rcar_du_group driver-specific object, without any real
counterpart in the DU documentation, that models those semi-global
resources.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Move the plane-related fields of struct rcar_du_device to their own
structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The struct rcar_du_encoder_data encoder::field describes the encoder
type, and the rcar_du_encoder_lvds_data and rcar_du_encoder_vga_data
structures describe connector properties. Rename them accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Create a single rcar_du_encoder structure that implements a KMS encoder.
The current implementation is straightforward and only configures CRTC
output routing.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The R8A7790 DU documentation contains further information regarding the
plane Y source coordinate. Update the comment accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Some of the DU revisions use one clock and IRQ per CRTC instead of one
clock and IRQ per device. Retrieve the correct clock and register the
correct IRQ for each CRTC.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The platform device id driver data field points to a device information
structure that only contains a (currently empty) features field for now.
Support for additional model-dependent features will be added later.
Only the R8A7779 variant is currently supported.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Replace the devm_request_mem_region() and devm_ioremap_nocache() calls
with devm_ioremap_resource().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Due to a misplaced memset(), we never actually enabled the FBC WM on HSW.
Move the memset() to happen a bit earlier, so that it won't clobber
results->enable_fbc_wm.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ryan noticed that on his board, HDMI was wired up to port C but not
exposed by the kernel, which had only expected DP on that port. Fix
that up by enumerating both ports if possible.
Tested-by: "Matsumura, Ryan" <ryan.matsumura@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Fix up the whitespace fail. Tsk.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The '!' here was not intended. Since '!' has higher precedence than
compare, it means the check is never true.
This regression was introduced in
commit 71fff20ff1
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Tue Aug 6 22:24:03 2013 +0300
drm/i915: Kill fbc_enable from hsw_lp_wm_results
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is an extra semi-colon here so we just leak and never unbind
anything.
This regression has been introduced in
commit 07fe0b1280
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Wed Jul 31 17:00:10 2013 -0700
drm/i915: plumb VM into bind/unbind code
Cc: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And also fix a small typo in the intel_encoder_dpms() comment.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
